Effect of electrode material on electrical discharge machining of alumina

Technologies for machining advanced insulating ceramics are demanded in many industrial fields. Recently, several insulating ceramics, such as Si₃N₄, SiC and ZrO₂, have been successfully machined by electrical discharge machining (EDM). As unstable discharges occur during the machining of Al₂O₃ ceramics, inferior machining properties have been obtained. The formation mechanism of the electrical conductive layer on the EDMed surface is much different as compared to other ceramics. In addition to this, the electrically conductive layers are not formed sufficiently to adhere to the EDMed workpiece surface and keep a stable and continuous discharge generation on the ceramics. Graphite is widely used as electrode material in EDM. It is expected that carbon from graphite electrode implant and generate a conductive layer. Copper, graphite (Poco EDM-3) and copper-infiltrated-graphite (Poco EDM-C3) electrodes were used to compare the effects of generation of a conductive layer on alumina corresponding to EDM properties. The electrical discharge machining of 95% pure alumina shows that the EDM-C3 performs very well, giving significantly higher material removal rate (MRR) and lower electrode wear ratio than the EDM-3 and copper electrodes. The value of MRR was found to increase by 60% for EDM-3 with positive electrode polarity. As for EDM-C3, MRR was increased by 80% under the same condition. When the results were investigated with energy dispersive spectroscopy (EDS), no element of copper was observed on the conductive layer with both EDM-3 and EDM-C3. However, surface resistivity of a conductive layer created with EDM-C3 is less than with EDM-3. Surface roughness was improved to 25 μm with positive polarity of EDM-C3.     

Experimental characterization of material removal in dry electrical discharge drilling

Dry electrical discharge machining is one of the novel EDM variants, which uses gas as dielectric fluid. Experimental characterization of material removal in dry electrical discharge drilling technique is presented in this paper. It is based on six-factor, three-level experiment using L₂₇ orthogonal array. All the experiments were performed in a ‘quasi-explosion’ mode by controlling pulse ‘off-time’ so as to maximize the material removal rate (MRR). Furthermore, an enclosure was provided around the electrodes with the aim to create a back pressure thereby restricting expansion of the plasma in the dry EDM process. The main response variables analyzed in this work were MRR, tool wear rate (TWR), oversize and compositional variation across the machined cross-sections. Statistical analysis of the results show that discharge current (I), gap voltage (V) and rotational speed (N) significantly influence MRR. TWR was found close to zero in most of the experiments. A predominant deposition of melted and eroded work material on the electrode surface instead of tool wear was evident. Compositional variation in the machined surface has been analyzed using EDAX; it showed migration of tool and shielding material into the work material. The study also analyzed erosion characteristics of a single-discharge in the dry EDM process vis-á-vis the conventional liquid dielectric EDM. It was observed that at low discharge energies, single-discharge in dry EDM could give larger MRR and crater radius as compared to that of the conventional liquid dielectric EDM.     

Performance and Surface Integrity of Ti6Al4V After Sinking EDM with Special Graphite Electrodes

Titanium and its alloys have high chemical reactivity with most of the cutting tools. This makes it difficult to work with these alloys using conventional machining processes. Electrical discharge machining (EDM) emerges as an alternative technique to machining these materials. In this work, it is investigated the performance of three special grades of graphite as electrodes when ED-Machining Ti6Al4V samples under three different regimes. The main influences of electrical parameters are discussed for the samples material removal rate, volumetric relative wear and surface roughness. The samples surfaces were evaluated using SEM images, microhardness measurements, and x-ray diffraction. It was found that the best results for samples material removal rate, surface roughness, and volumetric relative wear were obtained for the graphite electrode with 10-μm particle size and negative polarity. For all samples machined by EDM and characterized by x-ray (XRD), it was identified the presence of titanium carbides. For the finish EDM regimes, the recast layer presents an increased amount of titanium carbides compared to semi-finish and rough regimes.     

Surface modifications of Al–Zn–Mg alloy using combined EDM with ultrasonic machining and addition of TiC particles into the dielectric

This study proposes a novel combined process that integrates electrical discharge machining (EDM) and ultrasonic machining (USM) to investigate the machining performance and surface modification on Al–Zn–Mg alloy. In the experiment, TiC particles were added into the dielectric to explore the influence of the combined process on the material removal rate (MRR), the relative electrode wear ratio (REWR), the surface roughness and the expansion of the machined hole. The elemental distributions of titanium and carbon on the cross-section were quantitatively determined using an electron probe micro-analyzer (EPMA). Microhardness and wear resistance tests were conducted to evaluate the modifications on the machined surface caused by the combined process. The experimental results show that the combined process was associated with improved machining performance. The combination of EDM with USM yielded an alloyed layer that improved the hardness and wear resistance of the machined surface.     

The effect in EDM of a dielectric of a urea solution in water on modifying the surface of titanium

This study investigates the influence of the machining characteristics on pure titanium metals using an electrical discharge machining (EDM) with the addition of urea into distilled water. Additionally, the effects of urea addition on surface modification are also discussed. In the experiments, machining parameters such as the dielectric type, peak current and pulse duration were changed to explore their effects on machining performance, including the material removal rate, electrode wear rate and surface roughness. Moreover, the elemental distribution of nitrogen on the machined surface was qualitatively determined by EPMA to assess the effects on surface modification. Micro hardness and wear resistance tests were performed to evaluate the effects of the reinforced surface.Experimental results indicate that the nitrogen element decomposed from the dielectric that contained urea, migrated to the work piece, forming a TiN hard layer, resulting in good wear resistance of the machined surface after EDM.     

High-speed dry electrical discharge machining

A novel high-speed dry electrical discharge machining (EDM) method was proposed in this study. Using this method, the material can be rapidly melted by extremely high discharge energy and flushed out of the discharge gap by high-pressure and high-speed air flow. The material removal rate (MRR) of dry EDM was significantly improved by the proposed method. The MRR of dry EDM is usually in tens mm³/min, whereas the MRR of the proposed method can be as high as 5162 mm³/min, which improves the MRR by 2nd to 3rd order of magnitude. Investigation was conducted systemically. The influences of work piece polarity, discharge current, pulse duration time, gas pressure, and electrode rotation speed on machining performance were studied. The machining mechanism of this method was thoroughly analyzed. Moreover, the re-solidified layer, surface morphology, elementary composition, and phase of AISI 304 stainless steel for high-speed dry EDM were also investigated. Theoretical and technical foundations were laid for the industry application of dry EDM.     

Manufacturing linear and circular contours using CNC EDM and frame type tools

In traditional electro discharge machining (EDM) the usual practice is to form a 3D female cavity in the work piece by making a corresponding male shaped tool and plunging this into the work piece. Recently, however, computer numerical control (CNC) EDM machines have become available which have the potential to generate a detailed shape without using complex electrodes. This paper describes a novel method of electro discharge machining which makes the generation of linear, circular and curved contours possible without any special electrodes. The experimental work employs CNC EDM, mild steel work pieces and inexpensive “frame type” copper tools. The results indicate, relative to the cavities produced, an improved effective material removal rate (MRR), a better surface finish and a lower powered machine. The paper also introduces the effect of EDM parameters on the process performance by modelling and analysing the experimental results using statistical techniques. Finally, a few applications are discussed.     

High-speed EDM milling with moving electric arcs

A novel high-speed electrical discharge machining (EDM) milling method using moving electric arcs has been proposed in this study. We connected a copper electrode rotating rapidly around its axis and a work piece to a DC power supply to generate a moving electric arc. To ensure high relative speed of any point on the electrode with respect to the work piece, the electrode was shaped like a pipe. It was observed that the electric arcs move rapidly within the discharge gap due to the revolution of the tool electrode, removing the materials on the electrode along the track of the arc roots. To explore the characteristics of machining with moving electric arcs, an EDM milling apparatus was devised. Two planes with approximately the same roughness were machined separately by this equipment and a traditional EDM machine for comparison. It was found that a much higher material removal rate can be easily achieved by EDM milling with moving electric arcs. In the meanwhile, wear of the tool electrode in this new method is negligible, which is greatly favorable for machining accuracy. The microstructures of these surfaces were also investigated for further information.     

Probability of precision micro-machining of insulating Si3N4 ceramics by EDM

Electrical discharge machining (EDM) is used as a precision machining method for the electrically conductive hard materials with a soft electrode material. But recently we succeeded to machine on insulating material by EDM. The technology is named as an assisting electrode method. The EDMed surface is covered with the electrical conductive layer during discharge. The layer holds the electrical conductivity during discharge. For micro-EDM, the wear of tool electrode becomes lager ratio than the normal machining. So the micro-machining is extremely difficult to get the precision sample.

In this paper to obtain a fine and precise ceramics sample, some trials were carried out considering the EDM conditions, tool electrodes material and assisting electrode materials. Insulating Si₃N₄ ceramics were used for workpiece. The machining properties were estimated by the removal rate and tool wear ratio. To confirm the change of micro-machining process, the discharge waveforms were observed. The micro-machining of the Ø0.05 mm hole could be machined with the commercial sinking electrical discharge machine.     

Electrical Discharge Surface Alloying of Ti and Fe Workpiece Materials Using Refractory Powder Compact Electrodes and Cu Wire

The paper reviews the use of metal powders dispersed in the dielectric fluid and refractory PM electrodes, to initiate workpiece surface modification during EDM. Experimental work details the effects of EDM parameters (up to 270 V) on the hardness/composition of the white layer following die sink machining of AISI H13 tool steel and roll texturing of 2% Cr steel using partially sintered PM electrodes. Similar data are presented following EDM scanning and wire cutting of standard TI alloy TI-6AI-4V and a y TIAI. With AISI H13, recast layers were 5-20 μm thick and up to ∼ 1350 HK_0.025. When machining TI-6AI-4V with WC/Co electrodes, recast microhardness was 600-2900 HK_0.025. Wire cutting y TIAI generated porous alloyed layers up to 115 μm thick with extensive cracks and no increase in bulk hardness.     

Machining characteristics of magnetic force-assisted EDM

The gap conditions of electrical discharge machining (EDM) would significantly affect the stability of machining progress. Thus, the machining performance would be improved by expelling debris from the machining gap fast and easily. In this investigation, magnetic force was added to a conventional EDM machine to form a novel process of magnetic force-assisted EDM. The beneficial effects of this process were evaluated. The main machining parameters such as peak current and pulse duration were chosen to determine the effects on the machining characteristics in terms of material removal rate (MRR), electrode wear rate (EWR), and surface roughness. The surface integrity was also explored by a scanning electron microscope (SEM) to evaluate the effects of the magnetic force-assisted EDM. As the experimental results suggested that the magnetic force-assisted EDM facilitated the process stability. Moreover, a pertinent EDM process with high efficiency and high quality of machined surface could be accomplished to satisfy modern industrial applications.     

Workpiece surface modification using electrical discharge machining

Electrical discharge machining (EDM) is a widely used process in the mould / die and aerospace industries. Following a brief summary of the process, the paper reviews published work on the deliberate surface alloying of various workpiece materials using EDM. Details are given of operations involving powder metallurgy (PM) tool electrodes and the use of powders suspended in the dielectric fluid, typically aluminium, nickel, titanium, etc. Following this, experimental results are presented on the surface alloying of AISI H13 hot work tool steel during a die sink operation using partially sintered WC / Co electrodes operating in a hydrocarbon oil dielectric. An L8 fractional factorial Taguchi experiment was used to identify the effect of key operating factors on output measures (electrode wear, workpiece surface hardness, etc.). With respect to microhardness, the percentage contribution ratios (PCR) for peak current, electrode polarity and pulse on time were ˜24, 20 and 19%, respectively. Typically, changes in surface metallurgy were measured up to a depth of ˜30 μm (with a higher than normal voltage of ˜270 V) and an increase in the surface hardness of the recast layer from ˜620 HK_0.025 up to ˜1350 HK_0.025.     

超声振动辅助气中放电加工实验分析

超声振动辅助气中放电加工技术避免了常用的煤油等工作液作为介质带来的环境污染问题，具有工作环境清洁、适用范围广、加工效率高、工具电极简单等优点。实验研究了电压、脉冲宽度、峰值电流、超声振幅及气体介质压力等参数对加工效率、工件表面粗糙度及电极损耗的影响．并对试验结果进行了分析。     

Optimization of machining parameters in magnetic force assisted EDM based on Taguchi method

A versatile process of electrical discharge machining (EDM) using magnetic force assisted standard EDM machine has been developed. The effects of magnetic force on EDM machining characteristics were explored. Moreover, this work adopted an L18 orthogonal array based on Taguchi method to conduct a series of experiments, and statistically evaluated the experimental data by analysis of variance (ANOVA). The main machining parameters such as machining polarity (P), peak current (I_p), pulse duration (τ_p), high-voltage auxiliary current (I_H), no-load voltage (V) and servo reference voltage (S_v) were chosen to determine the EDM machining characteristics such as material removal rate (MRR) and surface roughness (SR). The benefits of magnetic force assisted EDM were confirmed from the analysis of discharge waveforms and from the micrograph observation of surface integrity. The experimental results show that the magnetic force assisted EDM has a higher MRR, a lower relative electrode wear ratio (REWR), and a smaller SR as compared with standard EDM. In addition, the significant machining parameters, and the optimal combination levels of machining parameters associated with MRR as well as SR were also drawn. Moreover, the contribution for expelling machining debris using the magnetic force assisted EDM would be proven to attain a high efficiency and high quality of surface integrity to meet the demand of modern industrial applications.     

On Electro Discharge Machining of Inconel 718 with Hollow Tool

Inconel 718 is a nickel-based alloy designed for high yield, tensile, and creep-rupture properties. This alloy has been widely used in jet engines and high-speed airframe parts in aeronautic application. In this study, electric discharge machining (EDM) process was used for machining commercially available Inconel 718. A copper electrode with 99.9% purity having tubular cross section was employed to machine holes of 20?mm height and 12?mm diameter on Inconel 718 workpieces. Experiments were planned using response surface methodology (RSM). Effects of five major process parameters??pulse current, duty factor, sensitivity control, gap control, and flushing pressure on the process responses??material removal rate (MRR) and surface roughness (SR) have been discussed. Mathematical models for MRR and SR have been developed using analysis of variance. Influences of process parameters on tool wear and tool geometry have been presented with the help of scanning electron microscope (SEM) micrographs. Analysis shows significant interaction effect of pulse current and duty factor on MRR yielding a wide range from 14.4 to 22.6?mm³/min, while pulse current remains the most contributing factor with approximate changes in the MRR and SR of 48 and 37%, respectively, corresponding to the extreme values considered. Interactions of duty factor and flushing pressure yield a minimum surface roughness of 6.2???m. The thickness of the sputtered layer and the crack length were found to be functions of pulse current. The hollow tool gets worn out on both the outer and the inner edges owing to spark erosion as well as abrasion due to flow of debris.     

A comparative experimental study of machining characteristics in vibratory, rotary and vibro-rotary electro-discharge machining

This paper compares the effects of high- and low-frequency forced axial vibration of the electrode, rotation of the electrode, and combinations of these methods in respect of material removal rate (MRR), tool wear rate and surface roughness in die sinking electro-discharge machining (EDM) with a flat electrode (planing mode).

The results of the combined states of rotation and vibration at high and low frequency (vibro-rotary EDM) are compared in order to establish which combinations are most appropriate to different machining regimes (finishing, semi-finishing and roughing). It is found that the combination of high-frequency vibration and rotation of the electrode is effective in attaining a high MRR at a specified surface roughness (R_a). This case is modelled by stepwise linear regression. The significant parameters are found by analysis of variance (ANOVA) and the optimum machining parameter settings are obtained using overlay contour plots. The advantages of vibration and rotation are seen to combine in this new process when employed for die sinking EDM with a flat electrode.     

Recast layer removal after electrical discharge machining via Taguchi analysis: A feasibility study

This study explores the feasibility of removing the recast layer (RCL) using etching and mechanical grinding for Ni-based superalloy materials by means of electrical discharge machining (EDM). The EDM process is widely used for machining hard metals and performing specific tasks that cannot be achieved using conventional techniques. The sparks produced during the EDM process melt the metal's surface, which then undergo ultra rapid quenching. A layer forms on the workpiece surface defined as a recast layer after solidification. Molds and dies desire to remove the RCL even though it is hard and has good matrix adherence.This experiment is divided into three stages. The first stage acquires a thick recast layer by using EDM with a larger discharging energy. A thick recast layer is essential for verification of the EDM technique for observing the recast process. Thus, this work applies the Taguchi L₁₈ analytical method to acquire the thick recast layer. The second stage optimizes the recast layer removal technique. Therefore, the thick recast layer is intentionally made in the first stage. This work determines the second stage setting using Taguchi's recommendation. Thus, the L₉ orthogonal array sets up the etching and mechanical grinding parameters and observes the recast layer removal quantity analysis. Finally, an experiment studies the surface characteristics of Ni-based superalloys, such as composition and micro-hardness after removing the recast layer.     

A study of EDM and ECM/ECM-lapping complex machining technology

EDM (electrodischarge machining) and ECM (electrochemical machining)/ECM-lapping complex machining is investigated in this paper. First, EDM shaping and ECM finishing technology are investigated. These processes are carried out in sequence on the same machine tool with the same electrode (copper) and the same machining liquid (water). Two types of EDM and ECM complex machining are investigated. One is with a formed electrode, and the other is with simple-shape electrode scanning. The complex machining with electrode scanning is applied to produce small and various-shaped components without making a formed electrode. The EDM surface of 1 μm Ra is improved to 0.2 μm Ra by applying ECM. Second, in order to get a smoother surface, a new EDM and ECM-lapping complex machining technology is developed. The surface roughness of a machined hole is improved to 0.07 μm Ra by applying 2 min of ECM lapping. The surface finishing of a hole shape is demonstrated with the complex machining technology.     

低盐溶液电火花-电解复合加工微小方孔试验

综合电火花加工快速蚀除材料与电解加工溶解重铸层的优势,提出了在低电导率的NaNO3溶液中使用电极逐层往复式铣削加工微小方孔的电火花-电解复合加工方法,并研究了电解液浓度、电压和电容参数对微小方孔加工质量的影响。结果表明:电解液浓度与加工电压对微小方孔加工质量影响较大,电容影响相对较小。选用最优加工参数在100μm厚的321不锈钢片上加工微小方孔,得到的方孔加工质量好、侧壁表面无重铸层,且工具电极相对损耗仅0.05%。     

Compound machining of titanium alloy by super high speed EDM milling and arc machining

A novel compound machining of titanium alloy (Ti6Al4V) by super high speed electrical discharge machining (EDM) milling and arc machining was proposed in this paper. The power supply consisted of a pulse generator and a DC power source which were isolated from each other. A rotating pipe graphite electrode was connected to the negative pole of the power supply. The plasma channel was able to deionize, and maximum material removal rate (MRR) reached 21,494 mm³/min with a relative electrode wear ratio (REWR) of 1.7% because of high current and efficient flushing. Compared with traditional EDM, the compound machining achieved a significantly higher MRR but a similar REWR. To investigate the characteristics of the compound machining, the effects of electrode polarity, peak voltage, peak current, and flushing pressure on the performance of the process, including its MRR, REWR, and radius of overcut (ROC), were determined. In addition, scanning electron microscopy, X-ray diffraction, and microhardness analysis were conducted. Result shows that the proposed method can machine difficult-to-machine materials efficiently.