Characterization of Ni–Cu–Zn ferrite prepared from industrial wastes

We propose the distillation method to synthesize Ni–Cu–Zn ferrite powder and to recover nitric acid, using scrap iron and the waste solution of electroplating as the starting materials. It was found that the Ni–Cu–Zn ferrite powder prepared from industry wastes also showed the formation of cubic ferrite with a saturation magnetization (M_s) of 55,825 A m² g⁻¹ and an intrinsic coercive force (Hci) of 579 A m⁻¹. For sintered Ni–Cu–Zn ferrite specimen, the toroidal specimen sintered at 950 °C for 2 h presented an maximum initial permeability (μ_i) of 176 at 28.3 MHz, a maximum quality factor (Q) of 32 at 3 MHz. The AC impedance measurements were performed by using impedance analyzer Solartron 1260. The semicircles in the impedance spectra shift to higher frequencies with increasing temperatures. The values of resistance (grain interior, grain boundary, and total) decreased with increasing temperatures. The semicircles of grain boundary and electrode are observed clearly. These data can be used to analyze typical the grain interior and the grain boundary resistance of Ni–Cu–Zn ferrite.     

Crystallization behavior of Bi1.25Y1.75Fe5O12 prepared by coprecipitation process

A non-isothermal study of the crystallization kinetic of coprecipitation of Bi_1.25Y_1.75Fe₅O₁₂ was carried out by differential scanning calorimetry (DSC). The Avrami exponent n suggesting the dimensionality of crystal growth was determined using the Ozawa equation. From non-isothermal DSC data presented values in range of 775–1023 kJ/mol and 3.28–2.10 for the activation energy of crystallization and the Avrami exponent, respectively. These Avrami exponent values were consistent with surface and internal crystallizations growth simultaneously.     

Structure,magnetic and transmission characteristics of the Co substituted Mg ferrites synthesized via a standard ceramic route

Co-Mg ferrites, ${\mathrm{Co}}_{\mathrm{x}}{\mathrm{Mg}}_{1?\mathrm{y}}{\mathrm{Fe}}_{2?\mathrm{z}}{\mathrm{O}}_4$ (x?=?0.0, 0.2, 0.4, 0.6, 0.8 and 1.0, 0?<?y?<?0.34 and 0?<?z?<?0.67), were synthesized via a standard ceramic route, and the structural, morphological, magnetic properties and transmission parameter of the samples were studied. The thermal behavior of the ground powder was characterized using a differential thermal analysis technique (DTA). The XRD patterns proved the formation of single phase Mg-ferrite in the samples with "x" contents varying from 0.0 to 0.8. The sample with x?=?1.0 showed two phases: a spinel Mg-ferrite and a secondary (Co,Mg)O phase. The lattice parameter and crystallite size of the samples increased remarkably by increasing the x content. The SEM images revealed that Co substitution in Mg ferrite at x?=?0.2 causes the particle growth, but their growth was not significant until x?=?0.8. For x?=?1.0, a remarkable particle growth was again observed. A maximum bulk density of 4.94?g/cm³ was obtained for x?=?0.8. Magnetic properties of the sintered samples showed an increase in coercive force up to 113?Oe by increasing Co substitution up to x?=?1.0. Saturation magnetization reached a maximum value of ~45.40?emu/g at x?=?0.8. Studying the microwave transmission behavior of the samples, using a vector network analyzer (VNA), indicated that by increasing Co, the transmission loss was reduced from $~$??15?dB for x?=?0.0 to less than ??10?dB for x?=?0.8 in the frequency range of 8–12?GHz.     

Electrical and magnetic properties of magnesium-substituted lithium ferrite

Magnesium-substituted lithium ferrite of different composition (Li_0.5Fe_2.5−xMg_xO_4−δ) were prepared for x = 0.0–1.0 by conventional ceramic technique. The crystal structure characterization and morphology were investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM). Initial permeability and quality factor were measured in the frequency range of 1 kHz to 100 MHz. The permeability decreased gradually from μ (f = 10 MHz) = 34.0 for Li_0.5Fe_2.5O₄ to μ (f = 10 MHz) = 11.5 for Li_0.5Fe_1.5Mg_1.0O₄. Electrical conductivity measurements were carried in the range of 250–700 °C in air. The maximum electrical conductivity, σ_700 °C = 0.1274 S/cm has been found to be for Li_0.5Fe_2.5O₄ specimen. With increasing Mg-substituted content, the decreased in the electrical conductivity.     

Structure and magnetic properties of multi-morphological CoFe2O4/CoFe nanocomposites by one-step hydrothermal synthesis

Multi-morphological CoFe₂O₄/CoFe nanocomposites have been synthesized using a facile hydrothermal process. The effects of hydrazine hydrate amount during hydrothermal reaction on the structure and magnetic property of the specimens were studied. With increasing hydrazine hydrate amount, the CoFe₂O₄ transformed to CoFe and the morphology of the specimen changed from granular particles to faceted particles. The saturation magnetization monotonically increased and the coercivity monotonically decreased with increasing hydrazine hydrate amount. The magnetic interactions, determining the magnetic properties of the composites, result from the dominant dipole coupling and relative weak exchange coupling between CoFe₂O₄ and CoFe nanoparticles. The CoFe₂O₄/CoFe nanocomposite prepared with 2?mL hydrazine hydrate exhibited the optimal magnetic properties, with the saturation magnetization of 81?emu/g and coercivity of 636?Oe.     

Magnetic and catalytic properties of copper ferrite nanopowders prepared by a microwave-induced combustion process

Copper ferrite nanopowders were successfully synthesized by a microwave-induced combustion process using copper nitrate, iron nitrate, and urea. The process only took a few minutes to obtain CuFe₂O₄ nanopowders. The resultant powders were investigated by XRD, SEM, VSM, and surface area measurement. The results revealed that the CuFe₂O₄ powders showed that the average particle size ranged from 300 to 600 nm. Also, it possessed a saturation magnetization of 21.16 emu/g, and an intrinsic coercive force of 600.84 Oe, whereas, upon annealing at 800 °C for 1 h. The CuFe₂O₄ powders specific surface area was 5.60 m²/g. Moreover, these copper ferrite magnetic nanopowders also acted as a catalyst for the oxidation of 2,3,6-trimethylphenol to synthesize 2,3,5-trimethylhydrogenquinone and 2,3,5-trimethyl-1,4-benzoquinone for the first time. On the basis of experimental evidence, a rational reaction mechanism is proposed to explain the results satisfactorily.     

Effect of Tb substitution on structural, magnetic and electrical properties of magnesium ferrites

A series of Mg_1−xTb_xFe₂O₄, ferrite samples (0.0 ≤ x ≤ 0.2) were synthesized by the ceramic method and were characterized by using X-ray diffraction, Fourier transform infrared spectroscopy (FTIR) and vibrating sample magnetometery. The XRD patterns showed the single phase ferrites up to x ≤ 0.04 without other secondary phase. The lattice constant increases slightly as a function of terbium content up to x = 0.04 and decreases for x > 0.04. The increase is attributed to the difference in the ionic radii of the cations involved and decrease led to the formation of secondary phase (TbFeO₃). The bulk density was found to increase from 3.5 to 4.6 (g/cm³) with the increase of terbium concentration. FTIR spectra exhibited two significant absorption bands in the wave number range of 370–1500 cm⁻¹ which confirm the spinel structure and completion of chemical reaction. The magnetic properties revealed a decrease in the saturation magnetization as a function of Tb content. An unexpected increase in magnetization at the Tb content of 0.02 could be due to the migration of Mg ions towards tetrahedral sites, consistent with the results of FTIR. Coercivity variations are attributed to the magneto-crystalline anisotropy. The resistivity increased with the substitution of terbium relative to the sample undoped with terbium while the drift mobility was found to decrease.     

Magnetic and thermal expansion properties of chromium-substituted lithium ferrite

The structure, magnetic, and thermal expansion properties of chromium-substituted lithium ferrite have been investigated. The lattice constant (Å) decreases linearly as a (x) = 8.32366 − 0.04338x for Li_0.5Fe_2.5−xCr_xO₄ (x = 0.0–1.0). When increasing Cr content, the initial permeability decreased gradually. The average thermal expansion coefficient of Li_0.5Fe_2.5−xCr_xO₄ (x = 0.0–1.0) varied from 15.34 to 17.77 ppm/°C, with increasing Cr content, the average thermal expansion coefficient decreased. The average thermal expansion coefficient (ppm/°C) in the range of 25–850 °C give the polynomial correlation as follows, TEC (x) = 1 7.775 − 0.216x − 0.723x² − 1.493x³ for Li_0.5Fe_2.5−xCr_xO₄ (x = 0.0–1.0).     

High permeability Ni-Cu-Zn ferrites through additive-free low-temperature sintering of nanocrystalline powders

Nanocrystalline Ni-Cu-Zn ferrite powders Ni_0.20Cu_0.20Zn_0.62Fe_1.98O_3.99 were prepared by thermal decomposition of an oxalate precursor. The particle size is 6 nm and 350 nm, respectively, for powders obtained through calcinations at 350 °C or 750 °C. The shrinkage behavior significantly changes with particle size; the temperature of maximum shrinkage rate is T_MSR = 700 °C for particles of 6 nm size and increases to T_MSR = 880 °C for particles 350 nm in size. Dense samples with a permeability of μ = 780 are obtained by sintering at 900 °C for 2 h. Mixtures of nanocrystalline and sub-micron powders allow tailoring of the shrinkage behavior. A maximum permeability of μ = 840 is obtained after sintering of a 1:1-mixture at 900 °C. This demonstrates the potential of nanocrystalline ferrites for co-firing without additives at 900 °C and integration of ferrite inductors into LTCC modules.     

Synthesis of ultradisperse NiFe2O4 spinel by thermal decomposition of citrate precursors and its magnetic properties

Peculiarities of synthesis of nanocrystalline NiFe₂O₄ powders by thermal decomposition of citrate precursors were investigated. It was found that the parameters of nanopowders are determined by the decomposition temperature and pH of the precursor media. The temperature and duration of the process of precursor decomposition are limiting factors for decrease of the grain size. An optimum relation between the limiting factors can be determined experimentally by variation of pH. Correlation between the synthesis parameters, particle size, and magnetic properties is discussed. It is shown that optimum magnetic and magnetostrictive properties were found for the bulk polycrystalline samples sintered using the powders obtained for pH 2.     

One-step hydrothermal synthesis and microwave electromagnetic properties of RGO/NiFe2O4 composite

The reduced graphene oxide (RGO)/NiFe₂O₄ composite was synthesized by a facile one-pot hydrothermal route, which avoided the usage of chemical reducing agent. The reduction of graphene oxide (GO) and the crystallization of NiFe₂O₄ crystals happened in a one-step hydrothermal process. The morphology, microstructure and magnetic properties of the composite were detected by means of XRD, XPS, TEM, EDX, TG-DSC and VSM. The maximum R_L of the RGO/NiFe₂O₄ composite is −39.7 dB at 9.2 GHz with the thickness of 3.0 mm, and the absorption bandwidth with the R_L below −10 dB is up to 5.0 GHz (from 12.7 to 17.7 GHz) with a thickness of 1.9 mm. The introduction of RGO signally enhanced microwave absorption performance of the NiFe₂O₄ NPs. It is believed that such composite will be applied widely in microwave absorbing area.     

Microstructure and electromagnetic properties of LiFe5O8 ferrite ceramics prepared from wet- and dry-milled powders

The effect of dry and wet ball milling of LiFe₅O₈ ferrite powder on the microstructure and electromagnetic properties of ferrite ceramics was studied using XRD analysis, scanning electron microscopy, dilatometry, thermogravimetry, calorimetry, and measurement of specific magnetization and electrical resistance. The sintering temperature was 1050 °C; the sintering time was 2 h. It was found that ferrite fabricated from dry-milled powder exhibits an ordered α-LiFe₅O₈ phase with bulk density of 91%. Its saturation magnetization and Curie temperature are 55 emu/g and 628°С, respectively. Specific electrical resistance is 4?10⁶ Ω cm. Wet milling in isopropyl alcohol causes formation of a disordered β-LiFe₅O₈ phase. Ceramics produced by this method shows higher bulk density (97%) and low porosity, and an order of magnitude lower resistivity. Its saturation magnetization and Curie temperature are 51 emu/g and 607°С, respectively.     

Controllable synthesis and magnetic properties of hydrothermally synthesized NiCo2O4 nano-spheres

In the work, we explored an efficient synthetic platform to purposefully fabricate different morphologies of NiCo₂O₄ by controlling the hydrothermal temperature. All the obtained samples were characterized by means of X-ray diffraction, scanning electron microscopy, high resolution transmission electron microscopy. With the increase of hydrothermal temperature, the morphology of obtained samples transformed from spongy nanosphere to ellipse-like, then to peanut-like structure and an effective blue shifting of Raman spectroscopy occurred. The magnetic measurements indicated that the materials transform from paramagnetic to weak ferromagnetic with the increase of hydrothermal temperature.     

Structural,electrical, and magnetic properties of Zn substituted magnesium ferrite

Zinc substituted magnesium (Mg–Zn) ferrites with the general formula Mg_1−xZn_xFe₂O₄ (x=0.00, 0.25, 0.50, 0.75, and 1.00) were prepared using the solution combustion route. The dried powder after calcination (700 °C for 2 h) was compacted and sintered at 1050 °C for 3 h. The structural, morphological, dielectric and magnetic properties of the sintered ferrites were studied using X-ray diffraction (XRD), scanning electron microscopy (SEM), impedance spectroscopy, and vibration sample magnetometry (VSM). The XRD analysis of sintered samples confirmed that the expected spinel cubic phase was formed for all samples. The crystallite sizes evaluated using Scherre's formula were found to be in the range of 47–80 nm. SEM analysis showed homogeneous grains with a polyhedral structure. The electrical conductivity increased with increasing frequency, which is normal dielectric behavior for such materials. The dielectric constant, dielectric loss tangent, and AC conductivity were found to be lowest for x=0.50. The VSM results showed that the zinc concentration had a significant influence on the saturation magnetization and coercivity.     

Microwave properties of chromium-substituted lithium ferrite

A structure characterization of chromium-substituted lithium ferrite specimens was carried out by the X-ray diffraction technique and found that the lattice parameter decreases with increasing of Cr-substitution content and the microstructure was determined by scanning electron microscopy (SEM), which revealed that the average grain size of chromium-substituted lithium ferrite decreases gradually with increasing Cr-substitution content.     

Dependence of photocatalytic activity on structural and optical properties of nanocrystalline ZnO powders

Nanocrystalline ZnO powders were prepared from cetyltrimethylammonium bromide (CTAB)-modified NaOH, NH₄OH and (CH₂)₆N₄ solutions. The calcined ZnO powders exhibited a hexagonal structure without any secondary phase. Different shapes of ZnO powders were formed depending on CTAB concentration and type of precipitating agent. As (CH₂)₆N₄ solution was used, rod-like ZnO structure was changed to a spherical shape when CTAB concentration was increased. The widest E_g value of approximately 3.23 eV was obtained from the sample containing the lowest defect concentration. The decolorization efficiency was higher than 90% after irradiating for 90 min and the sample with higher E_g value showed higher decolorization efficiency.     

Enhancing the magnetic and antibacterial properties of ZnO nanopowders through Mn+Co doping

Undoped and doubly (Mn+Co) doped ZnO nanopowders were synthesized with different doping levels of Co (1, 2, 3, 4 and 5 at%) and constant Mn doping level (10 at%) using a simple soft chemical route. XRD profiles confirmed that the synthesized material is nanocrystalline ZnO with hexagonal wurtzite structure. No peaks other than the characteristic ZnO peaks were observed in the XRD pattern confirming the absence of any secondary phase. Antibacterial activities of synthesized ZnO nanopowders were tested against Staphylococcus aureus bacteria using agar well diffusion method. It was found that the antibacterial efficiency of the doubly doped ZnO nanopowders was remarkably high when the Co doping level was 5 at%. The obtained PL, SEM and TEM results are corroborated well with the antibacterial activity. Magnetic measurements showed that undoped ZnO sample exhibits diamagnetic behavior and as the Co doping level increases, the nanopowder behaves as a ferromagnetic material.     

Effect of sintering regimes on the microstructure and magnetic properties of LiTiZn ferrite ceramics

In present work, the influence of sintering regimes on the microstructure, saturation magnetization, density and porosity, the grain size, the Curie point, and the temperature dependence of the initial permeability of LiTiZn ferrite ceramics was investigated. Ceramics was prepared by a standard ceramic technique. The formation of a single-phase cubic spinel structure was confirmed by XRD analysis. The Curie point was determined from both the temperature dependences of the initial permeability and the method of thermogravimetric measurements in a magnetic field. Density/porosity and the grain size, the Curie point and magnetization are sensitive to the sintering regime. The initial permeability of ferrite decreases with sintering temperature (in the range of 1010–1150?°С) and grain size increasing that contradicts the generally accepted Globus and Smith-Wijn theories. A possible reason of such behavior is the formation of intragranular pores growing with the increase in the sintering temperature and inhibiting the domain wall motion inside the grain. These results correspond to the porosity of the investigated ferrite ceramic samples, which grows with sintering temperature increasing.The non-stoichiometry arising due to evaporation of lithium and zinc oxides at temperature above 1010?°C affects the initial permeability. In this work, a qualitative assessment of the defective state of ferrite samples obtained under various sintering regimes was given.     

Structural,optical, and magnetic evaluation of Co-, Ni-, and Mn-modified multiferroic BiFeO3 ceramics

Co-, Ni-, and Mn-doped BiFeO₃ (BFO) ceramics were synthesized herein through a solid-state reaction. All doped BFO samples exhibit visible-light response, and the Co- and Ni-doped BFO samples present enhanced ferromagnetic order at room temperature. All doped samples show secondary phases in minor quantities. Optical spectra reveal two absorptions bands, indicating multiple electron transitions for BFO and its secondary phases. M ? H hysteresis loops suggest enhanced ferromagnetism in the Co- and Ni-doped BFO samples because of magnetic spinel CFP and NFO phases, respectively, whereas changes in oxygen vacancies and Fe–O–Fe bond angle play minor roles in the ferromagnetic behavior.     

Influence of Co content on the characterization and magnetic properties of magnetite

Preparation of nanosized Co_xFe_3−xO₄; 0.05 ≤ x ≤ 0.20 particles from metal nitrates solution through citrate–precursor method was performed. XRD pattern of all prepared systems showed single phase with cubic spinel structure. The crystallite size was determined from TEM and found to agree with that calculated from Sherrer's equation (60–76 nm) The magnetic constants such as molar magnetic susceptibility (χ_M), Curie temperature (T_C) and saturation magnetization (M_S) were measured and the results indicated that, at x = 0.2 the values of χ_M, M_S, remanent magnetization (M_r,) and coercive field (H_c) are 23 emu/g mol, 77.62 emu/g, 33.17 emu/g and 574.5 Oe, respectively_.