Investigation of crystallization behavior in dynamically vulcanized EPDM–nylon copolymer blends

A thermoplastic vulcanizate (TPV) of a ethylene–propylene–diene terpolymer (EPDM) and nylon copolymer (PA) was prepared by dynamic vulcanization. Maleic anhydride (MAH)–grafted EPDM (EPDM–g–MAH), MAH‐grafted EPR (EPR–g–MAH), and chlorinated polyethylene (CPE) were used as compatibilizers. The effect of dynamic vulcanization and compatibilizer on the crystallization behavior of PA was investigated. Differential scanning calorimeter measurement results showed no pronounced shift in the crystallization temperature for PA in EPDM–PA TPV compared to that for PA in the neat state, whereas the crystallization temperature increased after adding compatibilizer. The decrease in the crystallinity of TPVs was a result of the crystallization occurring in confined spaces between rubber particles. The equilibrium melting temperature (Tm⁰) of the PA copolymer was measured and was determined to be 157°C. The isothermal crystallization kinetics of PA in the neat and TPV states also was investigated. The crystallization rate was highest in the compatibilized TPV and lowest in the neat PA, whereas it was intermediate in the uncompatibilized TPV unvulcanized blends. Compared with unvulcanized EPDM–PA blends, the dynamic vulcanization process seemed to cause an obvious increase in the crystallization rate of the PA copolymer, especially when a suitable compatibilizer was used. This occurred because the dynamic vulcanization introduced fine crosslinked rubber particles that could act as heterogeneous nucleating centers. In addition, the use of a suitable compatibilizer permitted the formation of finely dispersed vulcanized rubber particles and therefore increased the density of the nucleating centers. The complex morphology of the blends was investigated by atomic force microscopy to evaluate the effect of compatibilizer on the size of the dispersed rubber particles. Compared with the morphology of TPVs with the same dosage of EPDM–g–MAH compatibilizer, the morphology of TPVs using EPR–g–MAH as compatibilizer showed much smaller dispersed rubber particles, which may have contributed to the higher crystallization rate. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 824–829, 2003     

Mechanical property and morphology comparison between the two blends poly(propylene)/ethylene‐propylene‐diene monomer elastomer and poly(propylene)/maleic anhydride‐g‐ethylene‐propylene‐diene monomer

The comparison of the mechanical properties between poly(propylene)/ethylene‐propylene‐diene monomer elastomer (PP/EPDM) and poly(propylene)/maleic anhydride‐g‐ethylene‐propylene‐diene monomer [PP/MEPDM (MAH‐g‐EPDM)] showed that the latter blend has noticeably higher Izod impact strength but lower Young's modulus than the former one. Phase morphology of the two blends was examined by dynamic mechanical thermal analysis, indicating that the miscibility of PP/MEPDM was inferior to PP/EPDM. The poor miscibility of PP/MEPDM degrades the nucleation effectiveness of the elastomer on PP. The observations of the impact fracture mode of the two blends and the dispersion state of the elastomers, determined by scanning electron microscopy, showed that PP/EPDM fractured in a brittle mode, whereas PP/MEPDM in a ductile one, and that a finer dispersion of MEPDM was found in the blend PP/MEPDM. These observations indicate that the difference in the dispersion state of elastomer between PP/EPDM and PP/MEPDM results in different fracture modes, and thereby affects the toughness of the two blends. The finer dispersion of MEPDM in the blend of PP/MEPDM was attributed to the part cross‐linking of MEPDM resulting from the grafting reaction of EPDM with maleic anhydride (MAH) in the presence of dicumyl peroxide (DCP). © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 2486–2491, 2002     

Dynamically cured polypropylene/Novolac blends compatibilized with maleic anhydride‐g‐polypropylene

In this article, the dynamic vulcanization process was applied to polypropylene (PP)/Novolac blends compatibilized with maleic anhydride‐grafted PP (MAH‐g‐PP). The influences of dynamic cure, content of MAH‐g‐PP, Novolac, and curing agent on mechanical properties of the PP/Novolac blends were investigated. The results showed that the dynamically cured PP/MAH‐g‐PP/Novolac blend had the best mechanical properties among all PP/Novolac blends. The dynamic cure of Novolac improved the modulus and stiffness of the PP/Novolac blends. The addition of MAH‐g‐PP into dynamically cured PP/Novolac blend further enhanced the mechanical properties. With increasing Novolac content, tensile strength, flexural modulus, and flexural strength increased significantly, while the elongation at break dramatically deceased. Those blends with hexamethylenetetramine (HMTA) as a curing agent had good mechanical properties at HMTA content of 10 wt %. Scanning electron microscopy (SEM) analysis showed that dynamically cured PP/MAH‐g‐PP/Novolac blends had finer domains than the PP/MAH‐g‐PP/Novolac blends. Thermogravimetric analysis (TGA) results indicated that the incorporation of Novolac into PP could improve the thermal stability of PP. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Synergetic toughness and morphology of poly(propylene)/nylon 11/maleated ethylene‐propylene diene copolymer blends

Polypropylene (PP)/nylon 11/maleated ethylene‐propylene‐diene rubber (EPDM‐g‐MAH) ternary polymer blends were prepared via melt blending in a corotating twin‐screw extruder. The effect of nylon 11 and EPDM‐g‐MAH on the phase morphology and mechanical properties was investigated. Scanning electron microscopy observation revealed that there was apparent phase separation for PP/EPDM‐g‐MAH binary blends at the level of 10 wt % maleated elastomer. For the PP/nylon 11/EPDM‐g‐MAH ternary blends, the dispersed phase morphology of the maleated elastomer was hardly affected by the addition of nylon 11, whereas the reduced dispersed phase domains of nylon 11 were observed with the increasing maleated elastomer loading. Furthermore, a core‐shell structure, in which nylon 11 as a rigid core was surrounded by a soft EPDM‐g‐MAH shell, was formed in the case of 10 wt % nylon 11 and higher EPDM‐g‐MAH concentration. In general, the results of mechanical property measurement showed that the ternary blends exhibited inferior tensile strength in comparison with the PP matrix, but superior toughness. Especially low‐temperature impact strength was obtained. The toughening mechanism was discussed with reference to the phase morphology. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

The effect of compatibilizers and organically modified nanoclay on the morphology and performance properties of poly(acrylonitrile–butadiene–styrene)/polypropylene blends

In this study, poly(acrylonitrile–butadiene–styrene)/polypropylene (ABS/PP) blends with various compositions were prepared by melt intercalation in a twin‐screw extruder. Modifications of the above blends were performed by using organically modified montmorillonite (OMMT, Cloisite 30B) reinforcement as well as two types of compatibilizers, namely polypropylene grafted with maleic anhydride (PP‐g‐MAH) and ABS grafted with maleic anhydride (ABS‐g‐MAH). Increasing the PP content in ABS matrix seems to increase the melt flow and thermal stability of their blends, whereas a deterioration of the tensile properties was recorded. On the other hand, the addition of ABS to PP promotes the formation of the β‐crystalline phase, which became maximum at 30 wt% ABS concentration, and increases the crystallization temperature (T_c) of PP. A tendency for increase of T_c was also recorded by incorporation of the above compatibilizers, whereas the glass transition temperature (T_g) of PP and SAN phase in ABS was reduced. Regarding the Young's modulus, the greatest improvement was observed in pure ABS/PP blends containing organically modified nanoclay. However, in reinforced pure PP, the use of compatibilizers is recommended in order to improve the elastic modulus. The addition of OMMT to noncompatibilized and compatibilized ABS/PP blends significantly improves their storage modulus. POLYM. ENG. SCI., 56:458–468, 2016. © 2016 Society of Plastics Engineers     

Mechanical,thermal, and morphological characteristics of compatibilized and dynamically vulcanized polyoxymethylene/ethylene propylene diene terpolymer blends

Dynamically vulcanized blends of polyoxymethylene (POM) and ethylene propylene diene terpolymer (EPDM) with and without compatibilizer were prepared by melt mixing in a twin screw extruder. Maleic anhydride (MAH) grafted EPDM (EPDM‐g‐MAH) has been used as a compatibilizer. Dicumyl peroxide was used for vulcanizing the elastomer phase in the blends. Mechanical, dynamical mechanical, thermal, and morphological properties of the blend systems have been investigated as a function of blend composition and compatibilizer content. The impact strength of both dynamically vulcanized blends and compatibilized/dynamically vulcanized blends increases with increase in elastomer content with decrease in tensile strength. Dynamic mechanical analysis shows decrease in tanδ values as the elastomer and compatibilizer content increased. Thermograms obtained from differential scanning calorimetric studies reveal that compatibilized blends have lower T_m values compared to dynamically vulcanized blends, which confirms strong interaction between the plastic and elastomer phase. Scanning electron microscopic observations on impact fractured surface indicate reduction in particle size of elastomer phase and its high level of dispersion in the POM matrix. In the case of compatibilized blends high degree of interaction between the component polymers has been observed. POLYM. ENG. SCI., 47:934–942, 2007. © 2007 Society of Plastics Engineers     

Morphology,rheology, and mechanical properties of dynamically cured EPDM/PP blend: Effect of curing agent dose variation

The structure development, rheological behavior, viscoelastic, and mechanical properties of dynamically cured blend based on the ethylene–propylene–diene terpolymer (EPDM) and polypropylene (PP) with a ratio of 60/40 by weight were studied. The variation of two‐phase morphology was observed and compared as the level of curing agent was increased. Meanwhile, as the level of curing agent increased, viscosity as a function of shear stress always increased at a shear stress range of 2.2 × 10⁴ to 3.4 × 10⁵ Pa at the temperature of 200°C, yet viscosity of the blend approached each other at high shear stress. Dynamic mechanical spectra at different temperatures show that dynamic modulus (E′) of the blend exhibits two drastic transitions corresponding to glass transition temperature (T_g) of EPDM and T_g of PP, respectively. In the blends T_gs of EPDM increase and T_gs of PP almost remain unchangeable with an increase in curing agent level. Tensile strength increased, yet elongation at break decreased as the level of curing agent is increased. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 357–362, 2004     

The dynamic mechanical analysis,impact, and morphological studies of EPDM–PVC and MMA‐g‐EPDM–PVC blends

The dynamic mechanical studies, impact resistance, and scanning electron microscopic studies of ethylene propylene diene terpolymer–poly(vinyl chloride) (EPDM–PVC) and methyl methacrylate grafted EPDM rubber (MMA‐g‐EPDM)–PVC (graft contents of 4, 13, 21, and 32%) blends were undertaken. All the regions of viscoelasticity were present in the E′ curve, while the E″ curve showed two glass transition temperatures for EPDM–PVC and MMA‐g‐EPDM–PVC blends, and the T_g increased with increasing graft content, indicating the incompatibility of these blends. The tan δ curve showed three dispersion regions for all blends arising from the α, β, and Γ transitions of the molecules. The sharp α transition peak shifted to higher temperatures with increasing concentration of the graft copolymer in the blends. EPDM showed less improvement while a sixfold increase in impact strength was noticed with the grafted EPDM. The scanning electron microscopy micrographs of EPDM–PVC showed less interaction between the phases in comparison to MMA‐g‐EPDM–PVC blends. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 71: 1959–1968, 1999     

The Effects of Dynamic Vulcanization by Dicumyl Peroxide (DCP) and N,N-m-Phenylene Bismaleimide (HVA-2) on the Properties of Polypropylene (PP)/Ethylene-Propylene Diene Terpolymer (EPDM)/Natural Rubber (NR) Blends

ABSTRACT

This paper discusses some properties of the polypropylene (PP)/ethylene-propylene diene terpolymer (EPDM)/natural rubber (NR) blends, such as tensile properties, heat resistance, gel content, and morphology. Dicumyl peroxide (DCP) and N,N-m-phenylene bismaleimide (HVA-2) and their combination were applied in PP/EPDM/NR blends as cross-link agents. In terms of tensile properties, the combination of DCP with HVA-2 shows the highest tensile strength and elongation at break in all PP/EPDM/NR blend ratios compared to similar blends, except with DCP or HVA-2 alone. The addition of HVA-2 produced blends with good heat resistance, while the combination of DCP with HVA-2 shows the highest gel content dealing with the cross-links formation. SEM micrographs from the surfaces extraction of the blends support that the cross-links have occurred during dynamic vulcanization process.     

Toughening of PP/EPDM blend by compatibilization

To improve the mechanical properties of blends of polypropylene (PP) and terpolymer of ethylene–propylene–diene (EPDM), a triblock copolymer, (PP‐g‐MAH)‐co‐[PA‐6,6]‐co‐(EPDM‐g‐MAH), was synthesized by coupling reaction of maleic anhydride (MAH)‐grafted PP (PP‐g‐MAH), EPDM‐g‐MAH, and PA‐6,6. The newly prepared block copolymer brought about a physical interlocking between the blend components, and imparted a compatibilizing effect to the blends. Introducing the block copolymer to the blends up to 5 wt % lead to formation of a β‐form crystal. The wide‐angle X‐ray diffractograms measured in the region of 2θ between 10° and 50° ascertained that incorporating the block copolymer gave a new peak at 2θ = 15.8°. The new peak was assigned to the (300) plane spacings of the β‐hexagonal crystal structure. In addition, the block copolymer notably improved the low‐temperature impact property of the PP/EPDM blends. The optimum usage level of the compatibilizer proved to be 0.5 wt %. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 1267–1274, 2000     

Influence of Copolymer Composition and Curing on Toughness of Isotactic Polypropene Blended Together with Metallocene‐EPDM and Ethene/Propene/Vinylcyclohexane Terpolymers

Ethene/propene terpolymers containing either 1‐vinylcylohexene‐4 (VCHen) or vinylcyclohexane (VCHan) as termonomer component were prepared using MAO‐activated rac‐Me₂Si(2‐MeBenz[e]Ind)₂ZrCl₂ (MBI). Propene content was varied between 26 and 72 wt.‐% with less than 1 mol‐% termonomer incorporation. Blends containing 85 vol.‐% isotactic polypropene (i‐PP) and 15 vol.‐% of the two EP terpolymer families were prepared by melt‐compounding in a twin‐screw kneader at 200°C to examine the role of sulfur‐mediated crosslinking of the unsaturated EPDM terpolymer phase in comparison to the corresponding blends containing non‐crosslinked saturated EP/VCHan terpolymers. The observed glass temperature (T_g) depression of the T_g of EP(D)M phases with respect to the T_g of the corresponding bulk EP(D)M was attributed to the presence of thermally induced stresses in both blend systems. Blends of i‐PP with crosslinked EPDM showed smaller T_g depression with respect to those of iPP/EPM blends containing non‐crosslinked EP and EPM dispersed phases. Morphology differences were detected for i‐PP/EPM and dynamically vulcanized i‐PP/EPDM blends by means of atomic force microscopy (AFM). The crosslinked i‐PP/EPDM blends exhibited significantly improved low temperature toughness as compared to the corresponding non‐crosslinked i‐PP/EPM blends. Curing of the EPDM elastomer phase in i‐PP/EPDM (85 vol.‐%/15 vol.‐%) blends afforded significantly improved toughness/stiffness balance and a wider toughness window with respect to the corresponding i‐PP/EPM and i‐PP/EP blends without sulfur‐cured rubber phases.     

Properties of copolymer-type polyacetal/ethylene–propylene–diene terpolymer blends

Two kinds of polymer blends, polyacetals (POMs) and ethylene–propylene–diene terpolymer (EPDM), have been prepared by mechanical blending. The rubbery EPDM was added to the rigid POM matrix to increase toughness. The mechanical, physical, thermal, dynamic mechanical, and morphological properties of these samples have been measured. The notched Izod impact strength and the elongation of the blends reaches a maximum at 7.5 wt % EPDM content. Scanning electron micrographs (SEM) showed that the domain sizes of EPDM vary from 0.25 to 1.0 μm and were independent of the composition. The POM/EPDM blends were determined to be immiscible by SEM, but showed single T_g behavior as determined by differential scanning calorimetry (DSC) and dynamic mechanical analyses up to 7.5 wt % EPDM. Because of that, the T_g's of POM and EPDM were very similar in value. © 1993 John Wiley & Sons, Inc.     

Compatibilizing effect of ethylene–propylene–diene grafted maleic anhydride terpolymer on the blend of polyamide 66 and thermal liquid crystalline polymer

Polyamide 66–thermal liquid crystalline polymer (PA66/TLCP) composites containing 10 wt% TLCP was compatibilized by ethylene–propylene–diene‐grafted maleic anhydride terpolymer (MAH‐g‐EPDM). The blending was performed on a twin‐screw extrusion, followed by an injection molding. The rheological, dynamic mechanical analysis (DMA), thermal, mechanical properties, as well as the morphology and FTIR spectra, of the blends were investigated and discussed. Rheological, DMA, and FTIR spectra results showed that MAH‐g‐EPDM is an effective compatibilizer for PA66/TLCP blends. The mechanical test indicated that the tensile strength, tensile elongation, and the bending strength of the blends were improved with the increase of the content of MAH‐g‐EPDM, which implied that the blends probably have a great frictional shear force, resulting from strong adhesion at the interface between the matrix and the dispersion phase; while the bending modulus was weakened with the increase of MAH‐g‐EPDM content, which is attributed to the development of the crystalline phase of PA66 hampered by adding MAH‐g‐EPDM. POLYM. COMPOS., 27:608–613, 2006. © 2006 Society of Plastics Engineers     

Synthesis of polypropylene‐graft‐maleic anhydride compatibilizer and evaluation of nylon 6/polypropylene blend properties

Polymer blends based on polyolefins are of a great interest owing to their broad spectrum of properties and practical applications. However, because of poor compatibilities of components, most of these systems generally exhibit high interfacial tension, a low degree of dispersion and poor mechanical properties. It is generally accepted that polypropylene (PP) and nylon 6 (N6) are not compatible and that their blending results in poor materials. The compatibility can be improved by the addition of a compatibilizer, and in this study PP was functionalized by maleic anhydride (MAH) in the presence of an optimized amount of dicumyl peroxide (DCP). The reaction was carried out in the molten state using an internal mixer. Then, once the compatibilizer polypropylene‐graft‐maleic anhydride (PP‐g‐MAH) was prepared, it was added at various concentrations (2.5–10 wt%) to 30/70 glass fibre reinforced N6 (GFRN6) PP, and the mechanical properties were evaluated. It was found that the incorporation of the compatibilizer enhanced the tensile properties (tensile strength and modulus) as well as the Izod impact properties of the notched samples. This was attributed to better interfacial adhesion as evidenced by scanning electron microscopy (SEM). The optimum in these properties was achieved at a critical PP‐g‐MAH concentration. Copyright © 2005 Society of Chemical Industry     

Preparation of polypropylene/acrylonitrile–styrene copolymer alloys by one‐step reactive blending

The compatibilization of polypropylene/acrylonitrile–styrene (PP/AS) blends through the addition of peroxide (DCP) was investigated in this study. The grafting reaction between PP and AS with the addition of peroxide occurred during the reactive‐blending process. The in situ‐formed grafting copolymers of PP‐g‐AS and AS‐g‐PP were then characterized by FTIR. The optimum concentration of the initiator, DCP, was 0.2 wt %, and the reaction temperature should be above 195°C. It was found that, when AS was the major component of the blends, the grafting of AS onto PP was the main process; conversely, when PP was the major component, PP was grafted onto AS. These results can be explained by the main‐chain scission of PP during the reactive‐blending process. With increase of the AS component, the total degree of grafting increased at first and then decreased after the composition of the blends reached 50/50. The maximum degree of grafting was found to be 6 wt % for the 50/50 PP/AS/DCP blend. PP was more degradable than was AS in the presence of peroxide at high temperatures. The MFR values of the PP/AS/DCP blends were slightly greater than were those of the simple PP/AS blends, which means that blending is an effective way to protect PP from degradation. SEM micrographs of the cross section of PP/AS/DCP showed a fine dispersion and a smaller domain size of the dispersed‐phase particles, implying that the in situ‐formed grafting copolymers act as a compatibilizer to reduce the interfacial tension between the PP and AS phases. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 1284–1290, 2001     

Dynamically vulcanized polypropylene/styrene–butadiene rubber blends: The effect of a peroxide/bismaleimide curing system and composition

Polypropylene (PP)/styrene–butadiene rubber blends were studied with special attention given to the effects of the blend ratio and dynamic vulcanization. Dicumyl peroxide (DCP) was used as the curing agent in combination with N,N′‐m‐phenylene bismaleimide (BMI) as the coagent for the curing process. Outstanding mechanical performance, especially with regard to the elongation at break, and better resistance to compression set were achieved with the dynamic vulcanization; this indicated that the DCP/BMI system also acted as a compatibilizing agent. This phenomenon was also confirmed by Fourier transform infrared spectroscopy of the insoluble material, the crystallinity degree of the PP phase (as investigated by X‐ray diffractometry), and scanning electron microscopy. The dynamic mechanical properties of the nonvulcanized and vulcanized blends were also investigated. The aging resistance of the blends was also evaluated. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

In situ dynamic vulcanization process in preparation of electrically conductive PP/EPDM thermoplastic vulcanizate/expanded graphite nanocomposites: Effects of state of cure

In situ melt dynamic vulcanization process has been employed to prepare electrically conductive polypropylene (PP)/ethylene–propylene–diene rubber (EPDM) (40/60 wt %) thermoplastic vulcanizates (TPVs) incorporated by expanded graphite (EG) as a conductive filler. Maleic anhydride grafted PP (PP‐g‐MAH) was used as compatibilizer and a sulfur curing system was designed and incorporated to vulcanize the EPDM phase during mixing process. Developed microstructures were characterized using scanning electron microscopy (SEM), melt rheomechanical spectroscopy (RMS), X‐ray diffraction (XRD), and transmission electron microscopy (TEM) and were correlated with electrical conductivity behavior. For comparison, another class of TPV/EG nanocomposites was fabricated using a commercially available PP/EPDM‐based TPV via both direct and masterbatch melt mixing process. Conductivity of the nanocomposites prepared by in situ showed no significant change during dynamic vulcanization till the mixing torque reached to the stationary level where micro‐morphology of the cured rubber droplets was fully developed, and conductivity abrupt was observed. In situ cured nanocomposites showed higher insulator to conductor transition threshold (3.15 vol % EG) than those based on commercially available TPV. All electrically conductive in situ prepared TPV nanocomposites exhibited reinforced melt elasticity with pseudosolid‐like behavior within low frequency region in dynamic melt rheometry indicating formation of physical networks by both EG nanolayers and crosslinked EPDM droplets. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Dynamically cured polypropylene/epoxy blends

The dynamic vulcanization process, usually used for the preparation of thermoplastic elastomers, was used to prepare polypropylene (PP)/epoxy blends. The blends had crosslinked epoxy resin particles finely dispersed in the PP matrix, and they were called dynamically cured PP/epoxy blends. Maleic anhydride grafted polypropylene (MAH‐g‐PP) was used as a compatibilizer. The effects of the reactive compatibilization and dynamic cure were studied with rheometry, capillary rheometry, and scanning electron microscopy (SEM). The crystallization behavior and mechanical properties of PP/epoxy, PP/MAH‐g‐PP/epoxy, and dynamically cured PP/epoxy blends were also investigated. The increase in the torque at equilibrium for the PP/MAH‐g‐PP/epoxy blends indicated the reaction between maleic anhydride groups of MAH‐g‐PP and the epoxy resin. The torque at equilibrium of the dynamically cured PP/epoxy blends increased with increasing epoxy resin content. Capillary rheological measurements also showed that the addition of MAH‐g‐PP or an increasing epoxy resin content increased the viscosity of PP/epoxy blends. SEM micrographs indicated that the PP/epoxy blends compatibilized with PP/MAH‐g‐PP had finer domains and more obscure boundaries than the PP/epoxy blends. A shift of the crystallization peak to a higher temperature for all the PP/epoxy blends indicated that uncured and cured epoxy resin particles in the blends could act as effective nucleating agents. The spherulites of pure PP were larger than those of PP in the PP/epoxy, PP/MAH‐g‐PP/epoxy, and dynamically cured PP/epoxy blends, as measured by polarized optical microscopy. The dynamically cured PP/epoxy blends had better mechanical properties than the PP/epoxy and PP/MAH‐g‐PP/epoxy blends. With increasing epoxy resin content, the flexural modulus of all the blends increased significantly, and the impact strength and tensile strength increased slightly, whereas the elongation at break decreased dramatically. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 1437–1448, 2004     

The control of miscibility of PP/EPDM blends by adding lonomers and applying dynamic vulcanization

The control of miscibility for isotactic polypropylene (PP) and ethylene-propylene-diene terpolymer (EPDM) has been attempted by adding poly(ethylene-comethacrylic acid) (EMA) ionomers and by applying dynamic vulcanization. The rheological properties, crystallization behavior, and morphology of the dynamically vulcanized EPDM/PP/ionomer ternary blends were investigated with a Rheometrics dynamic spectrometer (RDS), a differential scanning calorimeter (DSC), and a scanning electron microscope (SEM). Two kinds of EMA ionomers neutralized with different metal ions (Na⁺ and ZN⁺⁺) were investigated. Blends were prepared on a laboratory internal mixer at 190°C. Blending and curing were performed simultaneously, i.e., EPDM was vulcanized with dicumyl peroxide (DCP) in the presence of PP/ionomer. The composition of PP and EPDM was fixed at 50/50 by wt% and the contents of EMA ionomer were vaired from 5 to 20 parts based on the total amount of PP and EPDM. It was found that the addition of ionomers and the application of the dynamic vulcanization were effective in enhancing the miscibility of PP and EPDM. The structure of the blends was controlled by the following three component phases, i.e., the phase of the dynamially valcanized EPDM, PP, and Zn-neutralized ionomer. The ternary blends showed more miscibility than the PP/EPDM binary blend. This is due to the thermoplastic interpenetrating polymer network (IPN) of the ternary blends. The structure and properties of the ternary blends differed, depending on the types and contents of ionomer, i.e., the ternary blend containing Na-neutralized ionomer did not show a thermoplastic IPN structure clearly, even though the blend was prepared by dynamic vulcanization. The ternary blend containing Zn-neutralized ionomer clearly showed the behavior of a thermoplastic IPN when the contents of ionomer and DCP were 15 parts and 1.0 part, respectively.     

Thermoplastic elastomers based on high‐density polyethylene,ethylene–propylene–diene terpolymer,and ground tire rubber dynamically vulcanized with dicumyl peroxide

Thermoplastic vulcanizates (TPVs) based on high‐density polyethylene (HDPE), ethylene–propylene–diene terpolymer (EPDM), and ground tire rubber (GTR) were dynamically vulcanized with dicumyl peroxide (DCP). The polymer blend was composed of 40% HDPE, 30% EPDM, and 30% GTR, and the concentration of DCP was varied from 0.3 to 3.6 parts per hundred rubber (phr). The properties of the TPVs were determined by evaluation of the gel fraction content and the mechanical properties. In addition, IR spectroscopy and differential scanning calorimetry analysis were performed as a function of the DCP content. Decreases in the Young's modulus of the blends and the crystallinity of HDPE were observed when the content of DCP was greater than 1.8 phr. The results regarding the gel content indicate that the presence of DCP promoted the crosslinking of the thermoplastic matrix, and optimal properties were obtained with 1.5% DCP. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39901.