Dynamic mechanical and impact properties of polypropylene/EPDM blends

It was established by instrumented impact testing on notched Charpy specimens (DIN 53453 standard, No. 2 bar) that PP homopolymers impact modified by EPDM sorts of different melt viscosities at a rate lower than 10% were subject to brittle fracture in a wide temperature range. The most efficient of the EPDM impact modifiers had melt viscosities similar to that of the starting PP under the conditions of mixing. The course of maximum load at rupture (F_max) and notched impact strength as functions of temperature showed some analogies with one another as well as with the dynamic mechanical storage (E′) and with the mechanical loss factor (tan δ). Thus, linear regression analysis was applied to the following relations: F_max vs. (E′; tan δ; impact strength), F²_max vs. (tan δ, impact strength) and impact strength vs. tan δ. The optimum correlation coefficients were obtained for F_max vs. E′ and impact strength vs. tan δ. The supposed linearity of the former relation suggested that notched small Charpy specimens behaved as linear elastic bodies at high-rate three-point bending while the latter function referred to the significant role of relaxation of the EPDM impact modifier in the dissipation of impact energy during brittle or semi-brittle fracture of the two-phase PP/EPDM blends. The above relations are rendered probable by the fact that frequency of impact load is 10² to 10³ Hz while that of the dynamic mechanical measurements is about 10¹ Hz.     

Effect of dynamic crosslinking on tensile yield behavior of polypropylene/ethylene‐propylene‐diene rubber blends

Tensile yield behavior of the blends of polypropylene (PP) with ethylene‐propylene‐diene rubber (EPDM) is studied in blend composition range 0–40 wt % EPDM rubber. These blends were prepared in a laboratory internal mixer by simultaneous blending and dynamic vulcanization. Vulcanization was performed with dimethylol phenolic resin. For comparison, unvulcanized PP/EPDM blends were also prepared. In comparison to the unvulcanized blends, dynamically vulcanized blends showed higher yield stress and modulus. The increase of interfacial adhesion caused by production of three‐dimensional network is considered to be the most important factor in the improvement. It permits the interaction of the stress concentrate zone developed at the rubber particles and causes shear yielding of the PP matrix. Systematic changes with varying blend composition were found in stress‐strain behavior in the yield region, viz., in yield stress, yield strain, width of yield peak, and work of yield. Analysis of yield stress data on the basis of the various expressions of first power and two‐thirds power laws of blend compositions dependence and the porosity model led to consistent results from all expression about the variation of stress concentration effect in both unvulcanized and vulcanized blend systems. Shapes and sizes of dispersed rubber phase (EPDM) domains at various blend compositions were studied by scanning electron microscopy. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 2104–2121, 2000     

Miscibility of blends of ethylene‐propylene‐diene terpolymer and polypropylene

The miscibility of polymers is not only an important basis for selecting a proper blending method, but it is also one of the key factors in determining the morphology and properties of the blends. The miscibility between ethylene‐propylene‐diene terpolymer (EPDM) and polypropylene (PP) was explored by means of dynamic mechanical thermal analysis, transmission electron microscopy (TEM), and differential scanning calorimetry (DSC). The results showed that a decrease in the PP content and an increase of the crosslinking density of EPDM in the EPDM/PP blends caused the glass‐transition temperature peaks of EPDM to shift from a lower temperature to higher one, yet there was almost no variance in the glass‐transition temperature peaks of PP and the degree of crystallinity of PP decreased. It was observed that the blends prepared with different mixing equipment, such as a single‐screw extruder and an open mill, had different mechanical properties and blends prepared with the former had better mechanical properties than those prepared with the latter. The TEM micrographs revealed that the blends were composed of two phases: a bright, light PP phase and a dark EPDM phase. As the crosslinking degree of EPDM increased, the interface between the phases of EPDM and PP was less defined and the EPDM gradually dispersed in the PP phase became a continuous phase. The results indicated that EPDM and PP were both partially miscible. The mechanical properties of the blends had a lot to do with the blend morphology and the miscibility between the blend components. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 315–322, 2002     

Effect of dynamic cross‐linking on melt rheological properties of polypropylene/ethylene‐propylene‐diene rubber blends

Study of melts rheological properties of unvulcanized and dynamically vulcanized polypropylene (PP)/ethylene‐propylene‐diene rubber (EPDM) blends, at blending ratios 10–40 wt %, EPDM, are reported. Blends were prepared by melt mixing in an internal mixer at 190°C and rheological parameters have been evaluated at 220°C by single screw capillary rheometer. Vulcanization was performed with dimethylol phenolic resin. The effects of (i) blend composition; (ii) shear rate or shear stress on melt viscosity; (iii) shear sensitivity and flow characteristics at processing shear; (iv) melt elasticity of the extrudate; and (v) dynamic cross‐linking effect on the processing characteristics of the blends were studied. The melt viscosity increases with increasing EPDM concentration and decreased with increasing intensity of the shear mixing for all compositions. In comparison to the unvulcanized blends, dynamically vulcanized blends display highly pseudoplastic behavior provides unique processing characteristics that enable to perform well in both injection molding and extusion. The high viscosity at low shear rate provides the integrity of the extrudate during extrusion, and the low viscosity at high shear rate enables low injection pressure and less injection time. The low die‐swell characteristics of vulcanizate blends also give high precision for dimensional control during extrusion. The property differences for vulcanizate blends have also been explained in the light of differences in the morphology developed. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 1488–1505, 2000     

Mechanical and morphological properties of white rice husk ash filled polypropylene/ethylene‐propylene‐diene terpolymer thermoplastic elastomer composites

The performance of white rice husk ash (WRHA) as filler for polypropylene (PP)/ethylene‐propylene‐diene terpolymer (EPDM) thermoplastic elastomer (TPE) composites was investigated. The composites with different filler loadings were prepared in a Brabender plasticorder internal mixer. Both unvulcanized and dynamically vulcanized composites were prepared. Mixing and vulcanization processes of the composites were monitored through the typical Brabender torque‐time curves. The mechanical properties and morphology of the composites were also studied. The Brabender torque curves revealed that the dynamic vulcanization process employed was successful and incorporation of filler has no adverse effect on the processibility of the composites. Incorporation of WRHA improves the tensile modulus and flexural modulus and lowers tensile strength, elongation at break, tear strength, and toughness of both types of composites. Dynamic vulcanization significantly enhances the mechanical and TPE properties of the composites. Dynamic mechanical analysis (DMA) study revealed the existence of two phases in both types of composites. It further shows that neither dynamic vulcanization nor filler agglomeration has played a prominent role in the compatibility of the composites. Thermogravimetric investigation shows that dynamic vulcanization or WRHA loading has not adversely affected the thermal stability of the composites. The scanning electron micrographs provide evidence for the tendency to form filler agglomerates with increasing filler loading, better filler dispersion of dynamically vulcanized composites over unvulcanized composites, and effective vulcanization of elastomer phase of the composites in the presence of filler. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 438–453, 2002     

Structural characterization of reactor blends of polypropylene and ethylene‐propylene rubber

Blends of isotactic polypropylene (PP), ethylene‐propylene rubber copolymer (EPR), and ethylene‐propylene crystalline copolymer (EPC) can be produced through in situ polymerization processes directly in the reactor and blends with different structure and composition can be obtained. In this work we studied the structure of five reactor‐made blends of PP, EPR, and EPC produced by a Ziegler‐Natta catalyst system. The composition of EPR was related to the ratio between ethylene and propylene used in the copolymerization step. The ethylene content in the EPR was in the range of 50–70 mol %. The crystallization behavior of PP and EPC in the blends was influenced by the presence of the rubber, and some specific interactions between the components could be established. By preparative temperature rising elution fractionation (P‐TREF) analysis, the isolation and characterization of crystalline EPC fractions were made. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 2155–2162, 2004     

Compatibilization of nitrile‐butadiene rubber/ethylene‐propylene‐diene monomer blends by mercapto‐modified ethylene‐vinyl acetate copolymers

Mercapto‐modified ethylene‐vinyl acetate (EVASH) has been employed as a reactive compatibilizing agent for nitrile‐butadiene rubber (NBR)/ethylene‐propylene‐diene monomer (EPDM) blends vulcanized with a sulfur/2,2′‐dithiobisbenzothiazole (MBTS) single accelerator system and a (sulfur/MBTS/tetramethylthiuram disulfide (TMTD) binary accelerator system. The addition of 5.0 phr EVASH resulted in a significant improvement in the tensile properties of blends vulcanized with the sulfur/MBTS system. In addition to better mechanical performance, these functionalized copolymers gave rise to a more homogeneous morphology and, in some cases, better aging resistance. The compatibilization was not efficient in blends vulcanized with the S/MBTS/TMTD binary system, probably because of the faster vulcanization process occurring in this system. The good performance of these EVASH samples as compatibilizing agents for NBR/EPDM blends is attributed to the higher polarity of these components that is associated with their lower viscosity. Dynamic mechanical analysis also suggested a good interaction between the phases in the presence of EVASH. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 1404–1412, 2004     

Natural rubber–ethylene‐propylene‐diene rubber covulcanization: Effect of reinforcing fillers

Filled covulcanizates of elastomer blend comprising natural rubber (NR) and ethylene‐propylene‐diene rubber (EPDM) of commercial importance were successfully prepared by using a multifunctional rubber additive; namely, bis(diisopropyl)thiophosphoryl disulfide (DIPDIS). A Two‐stage vulcanization technique further improved the physicochemical properties of the blend vulcanizates by restricting, through the formation of polar rubber bound intermediates, the migration of curative and filler from lower to highly unsaturated rubber. Scanning electron microscopy studies indicate homogeneity and coherency in the morphology of the two‐stage vulcanizates. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 1001–1010, 2002; DOI 10.1002/app.10361     

Impact strength and dynamic mechanical properties correlation in elastomer‐modified polypropylene

This article describes the impact and dynamic mechanical properties of rubber‐modified binary blends of polypropylene (PP). Two conventional elastomers [viz. ethylene vinyl acetate copolymer (EVA) and ethylene propylene diene terpolymer (EPDM)] were used as an impact modifier for PP. It is clearly indicated by the results that EPDM is better than EVA as an impact modifier of PP. Analysis of data of dynamic mechanical properties and impact properties at various compositions of the blends revealed a direct correlation between impact properties and dynamic mechanical loss tangent. The energy dissipation due to viscoelastic relaxation is therefore suggested as a mechanism of impact toughening of PP, in addition to the other commonly known mechanisms of toughening (viz. shear yielding and crazing induced by deformation of rubber‐phase domains). © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 962–971, 2000     

Mechanical property and morphology comparison between the two blends poly(propylene)/ethylene‐propylene‐diene monomer elastomer and poly(propylene)/maleic anhydride‐g‐ethylene‐propylene‐diene monomer

The comparison of the mechanical properties between poly(propylene)/ethylene‐propylene‐diene monomer elastomer (PP/EPDM) and poly(propylene)/maleic anhydride‐g‐ethylene‐propylene‐diene monomer [PP/MEPDM (MAH‐g‐EPDM)] showed that the latter blend has noticeably higher Izod impact strength but lower Young's modulus than the former one. Phase morphology of the two blends was examined by dynamic mechanical thermal analysis, indicating that the miscibility of PP/MEPDM was inferior to PP/EPDM. The poor miscibility of PP/MEPDM degrades the nucleation effectiveness of the elastomer on PP. The observations of the impact fracture mode of the two blends and the dispersion state of the elastomers, determined by scanning electron microscopy, showed that PP/EPDM fractured in a brittle mode, whereas PP/MEPDM in a ductile one, and that a finer dispersion of MEPDM was found in the blend PP/MEPDM. These observations indicate that the difference in the dispersion state of elastomer between PP/EPDM and PP/MEPDM results in different fracture modes, and thereby affects the toughness of the two blends. The finer dispersion of MEPDM in the blend of PP/MEPDM was attributed to the part cross‐linking of MEPDM resulting from the grafting reaction of EPDM with maleic anhydride (MAH) in the presence of dicumyl peroxide (DCP). © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 2486–2491, 2002     

Studies on blends of natural rubber and ethylene propylene diene rubber modified with phosphorylated cardanol prepolymer: Processability,physico‐mechanical properties,and morphology

The melt processability and physico‐mechanical properties of blends of natural rubber (NR) and ethylene propylene diene rubber (EPDM) containing different dosages (0–10 phr) of phosphorylated cardanol prepolymer (PCP) were studied in unfilled and china‐clay‐filled mixes. The plasticizing effect of PCP in the blends was evidenced by progressive reduction in power consumption of the mixing and activation energy for melt flow with an increase in the dosage of PCP. The PCP‐modified blend vulcanizates showed higher tensile properties and tear strength despite a decrease in the chemical crosslink density (CLD) index. This is presumably due to the formation of a crosslinked network structure of PCP with the rubbers and improved dispersion of the filler particles in the rubber matrix, as evidenced by scanning electron microscopy (SEM) and atomic force microscopy (AFM). Thermogravimetric analysis showed an increase in thermal stability of the blend vulcanizate in presence of 5 phr of PCP. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 5123–5130, 2006     

Thermal and mechanical properties of silicon rubber/cis‐polybutadiene rubber/ethylene–propylene–diene monomer blends

Considering the properties of silicon rubber, ethylene–propylene–diene monomer (EPDM), and cis‐polybutadiene rubber (BR), a blend made by a new method was proposed in this article; this blend had thermal resistance and good mechanical properties. The morphology of the blend was studied by SEM, and it was found that the adhesion between the phases of BR, EPDM, and polysiloxanes (silicon rubber) could be enhanced, and the compatibility and covulcanization were good. The influence of the mass ratio of peroxide and silica on the mechanical properties and thermal resistance of the blend was studied. The results showed that the mechanical properties and thermal resistance of the blend were improved when silicon rubber/BR/EPDM was 20/30/50, dicumyl peroxide/sulfur was 2.5/2.5, and the amount of silica was 80 phr. The integral properties of rubber blend had more advantages than did the three rubbers. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 4462–4467, 2006     

Effect of different types of carbon black on the mechanical and acoustic properties of ethylene–propylene–diene rubber

The effects of the incorporation of different types of carbon black as fillers on some selected physical and mechanical properties of ethylene–propylene–diene rubber (EPDM) based compounds were studied with the results of density, ultrasonic wave velocity, and tensile measurements. Ultrasonic wave velocities (both longitudinal and shear) were measured at frequencies up to 4 MHz at room temperature. The density, ultrasonic attenuation coefficient, and tensile strength results showed that rubber mixes containing general‐purpose furnace (GPF) black at a concentration of 25 phr had the best physical and mechanical properties. These results were interpreted to be due to the better compatibility of GPF black, which, because of its particle size and structure, filled the interstitial spaces in EPDM and provided better reinforcement of the elastomer. The use of a nondestructive technique such as ultrasonic measurement presents a new possibility for testing rubber and plastic products more efficiently. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Effect of flexibility of ethylene vinyl acetate and crystallization of polypropylene on the mechanical properties of i‐PP/EVA blends

Polymer blend technology has been widely used for the past several years for the modification or enhancement of mechanical properties of polymers to obtain an overall balance of properties over those of the constituents. Despite its interesting mechanical and thermal properties, the impact strength of polypropylene leaves wide scope for improvement. A series of blends of ethylene vinyl acetate (EVA) copolymer with an impact grade of isotactic polypropylene (i‐PP) were prepared by single screw extrusion at 0–0.32 volume fraction of the dispersed phase. The mechanical properties such as tensile behavior, elongation‐at‐break, and impact strength of these blends systems as well as crystallinity were evaluated. Crystallinity data have been used in greater depth to support the mechanical properties. Differential scanning calorimetry studies conducted to study the modification in crystallinity of the crystalline component, i‐PP, of the blend revealed that the rubber component of the blend enhanced the crystallinity of i‐PP phase by providing sites for nucleation. Tensile modulus and strength decreased while the impact strength and breaking elongation enhanced with blending elastomer concentration. The improved properties of these PP/EVA blends are encouraging for carrying out further work on this system (composites) and suggest potential high impact strength applications for PP. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

环氧化天然橡胶共交联改性EPDM/NR共混物的性能

将三元乙丙橡胶(EPDM)与环氧化天然橡胶(ENR)共交联改性后,再与天然橡胶(NR)共混,考察了ENR共交联改性EPDM/NR共混胶的硫化特性、硫化胶的物理机械性能、溶胀指数和耐热空气老化性能,并对该硫化胶进行了差示扫描量热分析。结果表明,EPDM经过ENR共交联改性后与NR共混,ENR共交联改性EPDM/NR共混胶的交联程度明显提高,各相达到了同步交联,硫化胶的综合性能得到了显著改善。     

Dynamic mechanical properties of polypropylene‐g‐maleic anhydride and ethylene–propylene–diene terpolymer blends: Effect of blend preparation methods

In this work, we attempted two different ways of processing to improve interfacial adhesion of polypropylene (PP) and ethylene–propylene–diene terpolymer (EPDM) by introducing maleic anhydride (MAH); In one way, the in situ grafting and dynamic vulcanization (ISGV) were performed simultaneously from PP and EPDM with MAH in the presence of dicumyl peroxide (DCP) in an intensive mixer. In another way, PP was first grafted with MAH and then the PP‐g‐MAH was blended with EPDM in the intensive mixer in the presence of DCP by the dynamic vulcanization (DV). It was found that the glass transition temperatures (T_gs) of both PP and EPDM phases were shifted to higher temperature as the EPDM content increased for the blends prepared by both IGSV and DV methods, mainly due to the crosslinking of EPDM. The higher T_gs and larger storage moduli were observed for the blends prepared by the ISGV method than those prepared by the DV method, while the morphology showed that the size reduction of dispersed particles in latter blends was larger than that of the former blends. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 2777–2784, 2000     

The effects of dynamic vulcanization and compatibilizer on properties of paper sludge‐filled polypropylene/ethylene propylene diene terpolymer composites

The effects of dynamic vulcanization (DV) and dynamic vulcanization plus compatibilizer (DVC) of paper sludge (PS) filled polypropylene/ethylene propylene diene terpolymer (PP/EPDM) composites on torque development, mechanical properties, water absorption, morphology, and thermal properties were studied. Results show that DV and DVC composites exhibit higher stabilization torque than unvulcanized composites (UV). The dynamic vulcanized (DV) and dynamic vulcanized plus compatibilizer (DVC) composites exhibit higher tensile strength, elongation at break, and Young's modulus but lower water absorption than unvulcanized composites. The scanning electron microscopy (SEM) study of tensile fracture surface of DV and DVC composites shows the improved interfacial interaction between PS and PP/EPDM matrix. The DV and DVC composites also exhibit better thermal stability and higher crystallinity than unvulcanized PP/EPDM/PS composites. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

超细全硫化粉末丁苯橡胶/三元乙丙橡胶共混物的结构与性能

制备了超细全硫化粉末丁苯橡胶(UFPSBR)/三元乙丙橡胶(EPDM)共混物,研究了其硫化特性、相态结构、动态力学性能及物理机械性能。透射电镜观察表明,无论UFPSBR与EPDM共混比如何,UFPSBR粒子始终保持为分散相。当UFPSBR用量为10份(质量)时,它在EPDM中的分散相尺寸为200 nm左右;用量较高时其分散相尺寸较大,存在大量的聚集体。动态力学分析结果显示共混物存在2个玻璃化转变温度,说明共混物存在两相结构。加工性能分析结果表明,UFPSBR粒子在EPDM基质中形成了网络结构,对EPDM基质起到了较好的增强作用,当UFPSBR与EPDM的质量共混比为50/50时,共混物的拉伸强度可达13.4 MPa。UFPSBR对EPDM的硫化特性有明显影响。     

Rheological behavior and processability of polypropylene blends with rubber ethylene propylene diene terpolymer

A study of the dynamic complex and steady shear viscosity of isotactic polypropylene (iPP), ethylene–propylene diene terpolymer rubber (EPDM) and three different blends of both polymers are presented over a range of temperatures and frequencies. Moreover, the processability of these materials is studied through torque measurements during blend mixing. The results obtained show that the viscosity gradually increases with rubber content in the blend and decreases with both temperature and frequency. Plots of η″ versus η′ (Cole–Cole plots) show that the blend with the lower rubber content (25%), has a certain rheological compatibility with neat PP. Furthermore, torque curves measured during blend mixing confirm these results, demonstrating that the blend with 25% of elastomer has a similar behavior of iPP during processing. To analyze the morphological structure of the blends, a dynamic mechanical analysis of the solid state is also presented. It is observed that the blends have two distinct values of T_g close to the corresponding values of the pure polymers, confirming that this type of blends based on a semicrystalline polymer and an amorphous elastomer forms a two‐phase system with a limited degree of miscibility between both components. In addition, the polymer present with the higher concentration forms the continuous phase and controls the rheological properties of the blend. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 1–10, 2001     

Crystallization behavior and mechanical properties of polypropylene random copolymer/poly(ethylene‐octene) blends

New polymer blends of polypropylene random copolymer (PP‐R) and poly(ethylene‐octene) (POE) were prepared by melt‐blending process using a corotating twin‐screw extruder. The POE content was varied up to 35%. The toughening efficiency of POE for PP‐R was evaluated by the mechanical properties of the resulted PP‐R/POE blends. The crystallization behavior and morphology of the blends were also studied. Results show that POE acts as nucleation agent to induce the crystallization of PP‐R matrix at higher crystallization temperature. Super‐toughened PP‐R/POE blends (Izod impact strength more than 500 J/m) can be readily achieved with only 10 wt % of POE. The high toughness of PP‐R/POE is attributed to cavitation and shear yielding of matrix PP‐R, as revealed by the morphology studies. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011