Resistive switching characteristics of polyimides derived from 2,2′‐aryl substituents tetracarboxylic dianhydrides

2,2′‐Position aryl‐substituted tetracarboxylic dianhydrides including 2,2′‐bis(biphenyl)‐4,4′,5,5′‐biphenyl tetracarboxylic dianhydride and 2,2′‐bis[4‐(naphthalen‐1‐yl)phenyl)]‐4,4′,5,5′‐biphenyl tetracarboxylic dianhydride were synthesized. A new series of aromatic polyimides (PIs) were synthesized via a two‐step procedure from 3,3′,4,4′‐biphenyl tetracarboxylic dianhydride and the newly synthesized tetracarboxylic dianhydrides monomers reacting with 2,2′‐bis[4′‐(3″,4″,5″‐trifluorophenyl)phenyl]‐4,4′‐biphenyl diamine. The resulting polymers exhibited excellent organosolubility and thermal properties associated with T_g at 264 °C and high initial thermal decomposition temperatures (T_5%) exceeding 500 °C in argon. Moreover, the fabricated sandwich structured memory devices of Al/PI‐a/ITO was determined to present a flash‐type memory behaviour, while Al/PI‐b/ITO and Al/PI‐c/ITO exhibited write‐once read‐many‐times memory capability with different threshold voltages. In addition, Al/polymer/ITO devices showed high stability under a constant stress or continuous read pulse voltage of ? 1.0 V. Copyright © 2011 Society of Chemical Industry     

Structure and properties for conterminously linked polymer of copoly(amic acid) with triallyl isocyanurate and bismaleimide

The copoly(amic acid)s were prepared from two various diamines 2,2′‐bis (4‐aminophenoxy phenyl) hexafluoropropane or 2,2′‐bis (4‐aminophenoxy phenyl) propane and amine‐terminated oligosiloxane, respectively, with aromatic tetracarboxylic dianhydride (3,3′,4,4′‐benzophenone tetracarboxylic dianhydride). The resulted copoly(amic acid) with various mole ratio of triallyl isocyanurate (TAIC)/4,4′‐bismaleimidophenylmethane (BMI) were subsequently thermally imidized to the corresponding copolyimides. These polymers were characterized using viscometer, differential scanning calorimetry, thermogravimetric analyses, dynamic mechanical analysis (DMA), dielectric analyzer, and scanning electron microscope. The dielectric constant (D_K) and dissipation factor (D_f) of copolyimides with TAIC/BMI were much lower than that of copolyimides without TAIC/BMI. Furthermore, the formation of copolyimides also would enhance their thermal stability and solubility. DMA of copolymers showed only a glass transition temperature (T_g), indicating a random structure and an amorphous state. The morphology of copolyimides revealed no phase separation. This indicates that the homogeneous state has been achieved in this coreaction system. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Synthesis and characterization of novel adamantane‐based copoly(aryl ether ketone)s with low dielectric constants

A series of novel adamantane‐based copoly(aryl ether ketone)s (PAEK‐CF₃‐Ad) with low dielectric constants were prepared by post‐amidation of copoly(aryl ether ketone)s containing (3‐trifluoromethyl)phenyl and carboxyl groups with 4‐adamantylaniline. Compared with the preparation of adamantane‐containing poly(aryl ether ketone)s by direct polymerization of adamantyl‐substituted monomers, this side‐chain grafting method avoids various problems, such as high polymerization temperature and the difficult polymerization of adamantyl‐substituted monomers. The dielectric, thermal and mechanical properties of the synthesized PAEK‐CF₃‐Ad were characterized using a precision impedance analyzer, differential scanning calorimetry and thermogravimetric analysis, and a universal tester, respectively. The results indicate that PAEK‐CF₃‐Ad films exhibited low dielectric constants ranging from 2.33 to 2.65 at 1 MHz due to the introduction of the adamantyl groups. The synthesized PAEK‐CF₃‐Ad copolymers exhibited good thermal and mechanical properties. © 2013 Society of Chemical Industry     

Synthesis and properties of copolymers of poly(ether ketone ketone) and poly(ether amide ether amide ether ketone ketone)

Poly(aryl ether ketone)s (PAEKs) are a class of high‐performance engineering thermoplastics known for their excellent combination of chemical, physical and mechanical properties, and the synthesis of semicrystalline PAEKs with increased glass transition temperatures (T_g) is of much interest. In the work reported, a series of novel copolymers of poly(ether ketone ketone) (PEKK) and poly(ether amide ether amide ether ketone ketone) were synthesized by electrophilic solution polycondensation of terephthaloyl chloride with a mixture of diphenyl ether and N,N′‐bis(4‐phenoxybenzoyl)‐4,4′‐diaminodiphenyl ether (BPBDAE) under mild conditions. The copolymers obtained were characterized using various physicochemical techniques. The copolymers with 10–35 mol% BPBDAE are semicrystalline and have markedly increased T_g over commercially available poly(ether ether ketone) and PEKK due to the incorporation of amide linkages in the main chain. The copolymers with 30–35 mol% BPBDAE not only have high T_g of 178–186 °C, but also moderate melting temperatures of 335–339 °C, having good potential for melt processing. The copolymers with 30–35 mol% BPBDAE have tensile strengths of 102.4–103.8 MPa, Young's moduli of 2.33–2.45 GPa and elongations at break of 11.7–13.2%, and exhibit high thermal stability and good resistance to organic solvents. Copyright © 2010 Society of Chemical Industry     

Synthesis and properties of poly(aryl ether ketone)s containing both biphenylene moieties and sulfone linkages in the main chain

Two monomers, 4,4′‐bis(4‐phenoxybenzoyl)biphenyl (BPOBBP) and 4,4′‐diphenoxydiphenyl sulfone (DPODPS), were conveniently synthesized via simple synthetic procedures from readily available materials. A series of novel poly(aryl ether ketone)s containing both biphenylene moieties and sulfone linkages in the main chain were synthesized by the modified electrophilic Friedel‐Crafts acylation copolycondensation of isophthaloyl chloride (IPC) with a mixture of BPOBBP and DPODPS, over a wide range of BPOBBP/DPODPS molar ratios. The resulting polymers were characterized by Fourier transform infrared spectroscopy (FT‐IR), wide‐angle X‐ray diffraction (WAXD), differential scanning calorimetry (DSC), and thermogravimetric analysis (TGA), etc. The results indicated that the copolymers with 30 to 35 mol% DPODPS were semicrystalline and had remarkably increased glass transition temperatures (T_gs) over the conventional poly(ether ether ketone) (PEEK) and poly(ether ketone ketone) (PEKK) due to the incorporation of biphenylene units and sulfone linkages in the main chain. The copolymers with 30 to 35 mol% DPODPS had not only high T_gs of 176 to 177°C, but also moderate melting temperatures (T_ms) of 334 to 337°C, having good potential for the melt processing. The semicrystalline copolymers II to V had tensile strengths of 99.8 to 103.1 MPa, Young's moduli of 2.26 to 2.79 GPa, and elongations at break of 16.8 to 26.5% and exhibited outstanding thermal stability and good resistance to organic solvents. POLYM. ENG. SCI., 55:2140–2147, 2015. © 2015 Society of Plastics Engineers     

Highly fluorinated poly(ether‐imide)s derived from 2,2′‐bis(3,4,5‐trifluorophenyl)‐4,4′‐diaminodiphenyl ether and aromatic dianhydrides

A new diamine, 2,2′‐bis(3,4,5‐trifluorophenyl)‐4,4′‐diaminodiphenyl ether (FPAPE) was synthesized through the Suzuki coupling reaction of 2,2′‐diiodo‐4,4′‐dinitrodiphenyl ether with 3,4,5‐trifluorophenylboronic acid to produce 2,2′‐bis(3,4,5‐trifluorophenyl)‐4,4′‐dinitrodiphenyl ether (FPNPE), followed by palladium‐catalyzed hydrazine reduction of FPNPE. FPAPE was then utilized to prepare a novel class of highly fluorinated all‐aromatic poly(ether‐imide)s. The chemical structure of the resulting polymers is well confirmed by infrared and nuclear magnetic resonance spectroscopic methods. Limiting viscosity numbers of the polymer solutions at 25 °C were measured through the extrapolation of the concentrations used to zero. M_n and M_w of these polymers were about 10 000 and 25 000 g mol^?1, respectively. The polymers showed a good film‐forming ability, and some characteristics of their thin films including color and flexibility were investigated qualitatively. An excellent solubility in polar organic solvents was observed. X‐ray diffraction measurements showed that the fluoro‐containing polymers have a nearly amorphous nature. The resulting polymers had T_g values higher than 340 °C and were thermally stable, with 10% weight loss temperatures being recorded above 550 °C. Based on the results obtained, FPAPE can be considered as a promising design to prepare the related high performance polymeric materials. Copyright © 2011 Society of Chemical Industry     

Synthesis and gas transport properties of novel poly(aryl ether ketone)s with branched structure

Poly(aryl ether ketone)s (PAEKs) based on 2‐(3′‐trifluoromethylphenyl) hydroquinone and 4,4′‐difluorobenzophenone were synthesized and characterized in the presence or absence of 2,4′,6‐trifluorobenzophenone (BB′₂ monomer). The influence of the incorporation of a branched structure (BB′₂ monomer) on the gas transport properties of PAEKs was investigated. The results showed that PAEKs with a branched structure possess a higher permeability and selectivity than PAEKs without a branched structure. Moreover, improvements in the permeability and selectivity were enhanced with increasing content of BB′₂ monomer. This synergistic effect on permeability and selectivity was mainly due to the higher fractional free volume and the unique size and distribution of free volume holes arising from the incorporation of the branched structure. © 2013 Society of Chemical Industry     

Synthesis and properties of novel copolymers of poly(ether ketone diphenyl ketone ether ketone ketone) and poly(ether amide ether amide ether ketone ketone)

New monomers, 4,4′‐bis(4‐phenoxybenzoyl)diphenyl (BPOBDP) and N,N′‐bis(4‐phenoxybenzoyl)?4,4′‐diaminodiphenyl ether (BPBDAE), were conveniently synthesized via simple synthetic procedures from readily available materials. Novel copolymers of poly(ether ketone diphenyl ketone ether ketone ketone) (PEKDKEKK) and poly(ether amide ether amide ether ketone ketone) (PEAEAEKK) were synthesized by electrophilic Friedel‐Crafts solution copolycondensation of isophthaloyl chloride (IPC) with a mixture of BPOBDP and BPBDAE, over a wide range of BPOBDP/BPBDAE molar ratios, in the presence of anhydrous AlCl₃ and N‐methylpyrrolidone (NMP) in 1,2‐dichloroethane (DCE). The copolymers obtained were characterized by different physico‐chemical techniques. The copolymers with 10–40 mol% BPBDAE are semicrystalline and had remarkably increased T_gs over commercially available PEEK and PEKK due to the incorporation of amide and diphenyl linkages in the main chains. The copolymers IV and V with 30–40 mol% BPBDAE had not only high T_gs of 185–188°C, but also moderate T_ms of 326–330°C, having good potential for the melt processing. The copolymers IV and V had tensile strengths of 101.7–102.3 MPa, Young's moduli of 2.19–2.42 GPa, and elongations at break of 13.2–16.6% and exhibited high thermal stability and excellent resistance to organic solvents. POLYM. ENG. SCI., 54:1757–1764, 2014. © 2013 Society of Plastics Engineers     

Synthesis and thermotropic liquid‐crystalline behaviour of novel main‐chain poly(ether ether ketone ketone)s containing a lateral tert‐butyl group

The synthesis of novel poly(ether ether ketone ketone)s containing a lateral group via the random copolymerization of 4,4′‐biphenol, tert‐butylhydroquinone and 1,4‐bis(p‐fluorobenzoyl)benzene is described. The copolymers were characterized by differential scanning calorimetry (DSC), wide‐angle X‐ray diffraction (WAXD) and polarized optical microscopy (POM) observation. The results showed that the thermotropic liquid‐crystalline properties were achieved in the copolymers containing 30 mol% and 50 mol% tert‐butylhydroquinone, which have relatively lower melting temperatures due to the copolymerization effect. Both the crystalline–liquid‐crystalline transition (T_m) and the liquid‐crystalline–isotropic phase transition (T_i) were observable in the DSC thermograms, while the biphenol‐based poly(aryl ether ketone) has only one melting transition. The hydroquinone‐based polymer was shown to be amorphous. Thermogravimetric analysis (TGA) results showed that these copolymers are all high‐temperature resistant with higher glass transition temperature between 147 and 149 °C, and higher decomposition temperature T_d in the range 480–520 °C. © 2000 Society of Chemical Industry     

Organosoluble polyimides derived from asymmetric 2‐substituted‐and 2,2′,6‐trisubstituted‐4,4′‐oxydianilines

We report a new method for the preparation of asymmetric diamines using 4,4′‐oxydianiline (4,4′‐ODA) as the starting material. By controlling the equivalents of bromination agent, N‐bromosuccinimide, we were able to attach bromide and phenyl substituents at the 2‐ or 2,2′,6‐positions of 4,4′‐ODA. Thus, four new asymmetric aromatic diamines, 2‐bromo‐4,4′‐oxydianiline (6), 2,2′,6‐tribromo‐4,4′‐oxydianiline (7), 2‐phenyl‐4,4′‐oxydianiline (8) and 2,2′,6‐triphenyl‐4,4′‐oxydianiline (9), were synthesized by this method. Their structural asymmetry was confirmed using ¹H NMR spectroscopy. Asymmetric polyimides (PI10–PI13) were prepared from these diamines and three different dianhydrides (pyromellitic dianhydride (PMDA), 3,3′,4,4′‐biphenyltetracarboxylic dianhydride and 2,2‐bis(3,4‐dicarboxyphenyl)hexafluoropropane dianhydride) in refluxing m‐cresol. The formed polyimides, except PI10a derived from 6 and PMDA, were all soluble in m‐cresol without premature precipitation during polymerization. These polyimides with inherent viscosity of 0.41–0.96 dL g^?1, measured at a concentration of 0.5 g dL^?1 in N‐methyl‐2‐pyrrolidone at 30 °C, can form tough and flexible films. Because of the structural asymmetry, they also exhibited enhanced solubility in organic solvents. Especially, polyimides PI11a and PI13a derived from 7 and 9 with rigid PMDA were soluble in various organic solvents at room temperature. The structural asymmetry of the prepared polyimides was also evidenced from ¹H NMR spectroscopy. In the ¹H NMR spectrum of PI11a, the protons of pyromellitic moiety appeared in an area ratio of 1:2:1 at three different chemical shifts, which were assigned to head‐to‐head, head‐to‐tail and tail‐to‐tail configurations, respectively. These polyimides also exhibited good thermal stability. Their glass transition temperatures ranged from 297 to 344 °C measured using thermal mechanical analysis. © 2013 Society of Chemical Industry     

Sulfonated poly(arylene ether ketone)s prepared by direct copolymerization as proton exchange membranes: Synthesis and comparative investigation on transport properties

Sulfonated poly(aryl ether ketone)s (SPAEK) copolymers were synthesized by aromatic nucleophilic polycondensation from 3,3′, 5,5′‐tetramethyl‐4, 4′–biphenol, 1,4‐bis(4‐fluorobenzoyl) benzene, and disulfonated difluorobenzophenone. The SPAEK membranes did not exhibit excessive swelling in hot water and at the same time show the proton conductivities in the range of 0.030 S/cm to 0.099 S/cm at 80°C. The methanol diffusion coefficients of the SPAEK membranes were in the range of 4.7 × 10^?7 to 8.1 × 10^?7cm²/s measured at 25°C. The transport properties of this series of SPAEK copolymers were compared to poly(aryl ether ether ketone)s (SPEEK), poly(aryl ether ether ketone ketone)s (SPEEKK), and Nafion® membranes. It was found that the transport properties (including proton conductivity and methanol permeability) follows the trend of SPEEKK‐60 < SPAEK‐60 < SPEEK‐60 < Nafion® 117, the order of which is also attributed to the differences in the chemical structure of the polymers and the membrane morphology. In general, this novel series of SPAEK membranes possess various advantages, such as low cost of the initial monomers, high thermal and mechanical stability, and low methanol permeability while simultaneously possessing sufficient proton conductivity, which makes them notably promising as proton exchange membrane (PEM) materials in direct methanol fuel cell (DMFC) applications. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Fluorinated poly(aryl thioether)s and poly(aryl sulfone)s derived from 2,3,4,5,6‐pentafluorobenzoic acid

Poly(aryl thioether)s (F‐PTEs) containing 2,3,5,6‐tetrafluoro‐1,4‐phenylene moiety and polar moiety, such as 1,3,4‐ozadiazole, ether ketone, and amide groups, were synthesized by nucleophilic aromatic substitution reaction of aryl fluorides and 4,4′‐thiobisbenzenthiol. F‐PTEs were amorphous with good thermal properties including high glass transition temperature (T_g) and thermal stability, solubility, and hydrophobicity. F‐PTEs were transformed into poly(aryl sulfone)s (F‐PSs) by the oxidation reaction with hydrogen peroxide in acetic acid. Because of the sulfone group, the T_gs of the F‐PSs were 30–40°C higher than those of the corresponding F‐PTEs. F‐PSs maintained solubility in polar aprotic solvents and exhibited hydrophobicity in spite of the content of polar sulfone groups due to the highly substituted fluorine atoms. These F‐PTEs and F‐PSs were a new class of high‐performance polymers. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Synthesis and properties of poly(aryl ether sulfone ether ketone ketone) (PESEKK)

4,4′‐bis(Phenoxy)diphenyl sulfone (DPODPS) was synthesized by reaction of phenol with bis(4‐chlorophenyl) sulfone in tetramethylene sulfone in the presence of NaOH. Two poly(aryl ether sulfone ether ketone ketone)s (PESKKs) with high molecular weight were prepared by low temperature solution polycondensation of DPODPS and terephthaloyl chloride (TPC) or isophthaloyl chloride (IPC), respectively, in 1,2‐dichloroethane and in the presence of aluminum chloride (AlCl₃) and N‐methylpyrrolidone (NMP). The resulting polymers were characterized by various analytical techniques, such as FT‐IR, ¹H‐NMR, DSC, TG, and WAXD. The results show that the T_g and T_d of PESEKKs are much higher, but its T_m is lower than those of PEKK. The other results indicate that PESEKKs exhibit excellent thermostabilities at 300 ± 10°C. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 489–493, 2005     

New polymer syntheses: II. Preparation of aromatic poly(ether ketone)s from silylated bisphenols

Bulk condensations of 4,4′-difluorobenzophenone and various silylated bisphenols were carried out at 220°–320°C, with caesium fluoride as catalyst. Silylated bisphenol-A, tetramethylbisphenol-A, 1,1-bis(4-hydroxyphenyl)cyclohexane or 4,4′-dihydroxydiphenylsulphone as monomers and glassy polymers were soluble in several organic solvents. Their glass transitions were determined by differential scanning calorimetry (d.s.c.) and their number molecular weights ($\text{M}\text{?}{}_{\mathrm{<mtext>n</mtext>}}$) determined by means of vapour pressure osmometry. M_n's up to 10 000 were obtained. When silylated hydroquinone, 4,4′-dihydroxydiphenyl, 2,7-dihydroxynaphthalene or 4,4′-dihydroxydiphenylsulphide undergo polycondensation the resulting poly (ether ketone)s form crystals. It is demonstrated that transesterification does not take place and that block copoly(ether ketone-ether sulphone)s are synthesized. Furthermore, the thermostability of the poly(ether ketone)s in air was investigated.     

Synthesis of a novel hexaarylbiimidazole with ether groups and characterization of its photoinitiation properties for acrylate derivatives

A novel photoinitiator 2,2′‐bis‐(2‐chlorophenyl)‐4,4′,5,5′‐tetra‐[3‐(2‐hydroxylmethyl‐2‐triethylene glycol monoethylene ether‐ethane‐1‐oxy)‐phenyl]‐1,2′‐biimidazole (BCTE‐HABI) was synthesized from 3,3′‐dimethoxy benzoin. Ultraviolet spectra, fluorescence spectra, ESR, photodilatometer, and photo‐DSC measurements indicate that its photoinitiating activity for acrylate derivatives is better than 2,2′‐bis‐(2‐chlorophenyl)‐4,4′,5,5′‐tetraphenyl‐1,2′‐biimidazole (o‐Cl‐HABI), which is one of the most widely studied and used derivatives of HABI. POLYM. ENG. SCI., 46:474–479, 2006. © 2006 Society of Plastics Engineers.     

Synthesis and characterization of organo‐soluble poly(ether ether ketone)s and poly(ether ether ketone ketone)s containing pendant pentadecyl chains

Poly(ether ether ketone)s and poly(ether ether ketone ketone)s containing pendant pentadecyl chains were synthesized by polycondensation of each of the two bisphenol monomers viz, 1,1,1‐[bis(4‐hydroxyphenyl)‐4′‐pentadecylphenyl]ethane and 1,1‐bis(4‐hydroxyphenyl)‐3‐pentadecyl cyclohexane with activated aromatic dihalides namely, 4,4′‐difluorobenzophenone, and 1,3‐bis(4‐fluorobenzoyl)benzene in a solvent mixture of N,N‐dimethylacetamide and toluene, in the presence of anhydrous potassium carbonate. Polymers were isolated as white fibrous materials with inherent viscosities and number average molecular weights in the range 0.70–1.27 dL g^?1 and 76,620–1,36,720, respectively. Poly(ether ether ketone)s and poly(ether ether ketone ketone)s were found to be soluble at room temperature in organic solvents such as chloroform, dichloromethane, tetrahydrofuran, and pyridine and could be cast into tough, transparent, and flexible films from their solutions in chloroform. Wide angle X‐ray diffraction patterns exhibited a broad halo at around 2θ = ～ 19° indicating that the polymers containing pentadecyl chains were amorphous in nature. In the small‐angle region, diffuse reflections of a typically layered structures resulting from the packing of pentadecyl side chains were observed. The temperature at 10% weight loss, obtained from TG curves, for poly(ether ether ketone)s and poly(ether ether ketone ketone)s were in the range 416–459°C, indicating their good thermal stability. A substantial drop in glass transition temperatures (68–78°C) was observed for poly(ether ether ketone)s and poly(ether ether ketone ketone)s due to “internal plasticization” effect of flexible pendant pentadecyl chains. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Synthesis of aromatic poly(urea‐imide) with heterocyclic side‐chain structure

The poly(urea‐imide) copolymers with inherent viscosity of 0.81–1.08 dL/g were synthesized by reacting aryl ether diamine or its polyurea prepolymer with various diisocyanate‐terminated polyimide prepolymers. The aryl ether diamine was obtained by first nucleophilic substitution of phenolphthalein with p‐chloronitrobenzene in the presence of anhydrous potassium carbonate to form a dinitro aryl ether, and then further hydrogenated to diamine. The polyimide prepolymers were prepared by using 4,4′‐diphenylmethane diisocyanate to react with pyromellitic dianhydride, 3,3′,4,4′‐benzophenonetetracarboxylic dianhydride, or 3,3′,4,4′‐sulfonyldiphthalic anhydride by using the direct one‐pot method to improve their solubility, but without sacrificing thermal property. These copolymers are amorphous and readily soluble in a wide range of organic solvents such as N‐methyl‐2‐pyrrolidone, dimethylimidazole, N,N‐dimethylacetamide, dimethyl sulfoxide, N,N‐dimethylformamide, m‐cresol, and sulfolane. All the poly(urea‐imides) have glass transition temperatures in the range of 205–240°C and show a 10 wt % loss at 326–352°C in nitrogen and 324–350°C in air. The tensile strength, elongation at break, and initial modulus of these copolymer films range from 42 to 79 MPa, 5 to 16%, and 1.23 to 2.02 GPa, respectively. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 1719–1730, 1999     

Kinetics of azo‐initiated 1‐vinyl‐2‐pyrrolidone polymerizations at low conversions in aqueous media

The free‐radical polymerization behavior of 1‐vinyl,2‐pyrrolidone (NVP) was studied at low conversions, using capillary dilatometry. The aqueous media were kept at neutral pH and the studies were conducted isothermally, at 40 or 45°C. The azo‐type initiators used were 4,4′‐azobis‐4‐cyanopentanoic acid (ACPA), 2,2′‐azobisisobutyronitrile (AZBN), and 2,2′‐azobis[2‐(2‐imidazolin‐2‐yl)propane dihydrochloride] (ABDH). The monomer concentration and initiator concentration ranges were 1.17–2.34 mol L⁻¹ and 1–8 mmol L⁻¹, respectively. The rates of polymerization (R_p) and orders of reaction with respect to NVP and the initiator were evaluated and the kinetic equations were found to be R_p ∝ [NVP] [ACPA]^1.2; R_p ∝ [NVP] [AZBN]^1.1; and R_p ∝ [NVP]^2.2 [ABDH]^1.1. The polymers obtained were characterized by their viscosity numbers and correlation of the viscosity average molecular weights made with the type and amount of the azo initiator. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 75: 239–246, 2000     

Synthesis and characterization of highly soluble poly(ether imide)s containing indane moieties in the main chain

A new indane containing unsymmetrical diamine monomer ( 3 ) was synthesized. This diamine monomer leads to a number of novel semifluorinated poly (ether imide)s when reacted with different commercially available dianhydrides like benzene‐1,2,4,5‐tetracarboxylic dianhydride (PMDA), benzophenone‐3,3′, 4,4′‐tetracarboxylic dianhydride (BTDA), 4,4′‐(hexafluoro‐isopropylidene)diphthalic anhydride (6FDA), 4,4′‐oxydiphthalic anhydride (ODPA), and 4,4′‐(4,4′‐Isopropylidenediphenoxy)bis(phthalic anhydride) (BPADA) by thermal imidization route. All the poly(ether imide)s showed excellent solubility in several organic solvents such as N‐methylpyrrolidone (NMP), N,N‐dimethylformamide (DMF), N,N‐dimethylacetamide (DMAc), tetrahydrofuran (THF), chloroform (CHCl₃) and dichloromethane (DCM) at room temperature. These light yellow poly (ether imide)s showed very low water absorption (0.19–0.30%) and very good optical transparency. Wide angle X‐ray diffraction measurements revealed that these polymers were amorphous in nature. The polymers exhibited high thermal stability up to 526°C in nitrogen with 5% weight loss, and high glass transition temperature up to 265°C. The polymers exhibited high tensile strength up to 85 MPa, modulus up to 2.5 GPa and elongation at break up to 38%, depending on the exact polymer structure. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Novel poly(ether ketone)arylates: Synthesis,characterization and properties

In order to reduce the melt temperature (T_m) of the thermotropic crystalline polyarylate and improve its compatibility with poly(ether ether ketone) (PEEK), a series of poly(ether ketone)arylates (PEKARs) containing aryl ether ketone units (AEK) are synthesized through melt transesterification reaction from p‐acetoxybenzoic acid, 1,3‐bis(4′‐carboxylphenoxy)benzene and 4,4′‐bis(p‐acetoxyphenoxy)benzophenone. The inherent viscosities of these polymers are in the range 0.35–0.81 dL/g. The morphologies and properties of PEKARs are characterized by polarized optical microscopy, wide‐angle X‐ray diffraction, differential scanning calorimetry, thermal gravimetric analysis, etc. The results show that all PEKARs are semi‐crystalline polymers, and the introduction of AEK units can reduce the symmetry of the main chains, leading to decreasing the crystallizability and changing the crystalline form. The PEKARs with AEK less than 30% can exhibit thermotropic liquid crystalline state. The initial and the maximum decomposition temperatures increase with the increase in AEK content. These PEKARs are expected to act as processing agents for PEEK to reduce its processing viscosity. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013