Surface modification of poly(ether sulfone) ultrafiltration membranes by low‐temperature plasma‐induced graft polymerization

Low‐temperature helium plasma treatment followed by grafting of N‐vinyl‐2‐pyrrolidone (NVP) onto poly(ether sulfone) (PES) ultrafiltration (UF) membranes was used to modify commercial PES membranes. Helium plasma treatment alone and post‐NVP grafting substantially increased the surface hydrophilicity compared with the unmodified virgin PES membranes. The degree of modification was adjusted by plasma treatment time and polymerization conditions (temperature, NVP concentration, and graft density). The NVP‐grafted PES surfaces were characterized by Fourier transform infrared attenuated total reflection spectroscopy and electron spectroscopy for chemical analysis. Plasma treatment roughened the membrane as measured by atomic‐force microscopy. Also, using a filtration protocol to simulate protein fouling and cleaning potential, the surface modified membranes were notably less susceptible to BSA fouling than the virgin PES membrane or a commercial low‐protein binding PES membrane. In addition, the modified membranes were easier to clean and required little caustic to recover permeation flux. The absolute and relative permeation flux values were quite similar for the plasma‐treated and NVP‐grafted membranes and notably higher than the virgin membrane. The main difference being the expected long‐term instability of the plasma treated as compared with the NVP‐grafted membranes. These results provide a foundation for using low‐temperature plasma‐induced grafting on PES with a variety of other molecules, including other hydrophilic monomers besides NVP, charged or hydrophobic molecules, binding domains, and biologically active molecules such as enzymes and ribozymes. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 72: 1699–1711, 1999     

Surface modification of poly(ethylene terephthalate) film by coating with poly(ethylene glycol)‐grafted polystyrene

The poly(ethylene glycol) (PEG)‐grafted styrene (St) copolymer, which was formed as a nanosphere, was used as an agent to modify the surface of poly(ethylene terephthalate) (PET) film. The graft copolymer was dissolved into chloroform and coated onto the PET film by dip–coating method. The coated amount depends on the content ratios of PEG and St, the solution concentration, and the coating cycles. The graft copolymers having a low molecular weight of PEG‐ or St‐rich content was fairly stable on washing in sodium dodecyl sulfate (SDS) aqueous solution. It was confirmed that the PET surface easily altered its surface property by the coating of the graft copolymers. The contact angles of the films coated with the graft copolymers were very high (ca. 105–120°). The coated film has good antistatic electric property, which agreed with PEG content. The best condition of coating is a one‐cycle coating of 1% (w/v) graft copolymer solution. The coated surface had water‐repellency and antistatic electric property at the same time. The graft copolymer consisted of a PEG macromonomer; St was successfully coated onto PET surfaces, and the desirable properties of both of PEG macromonomer and PSt were exhibited as a novel function of the coated PE film. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 1524–1530, 1999     

Synthesis and surface properties of polystyrene‐graft‐poly(ethylene glycol) copolymers

Polystyrene‐graft‐poly(ethylene glycol) copolymers (PS‐g‐PEG) were successfully synthesized using the “grafting‐through” method. The graft copolymers and the surface properties of their coats were characterized by 1 H‐NMR, gel permeation chromatography (GPC), differential scanning calorimetry (DSC), transmission electron microscopy (TEM), X‐ray photoelectron spectroscopy (XPS), static contact angle measurement, and atomic force microscopy (AFM). Both DSC and TEM indicated that the graft copolymers had a microphase separated structure. AFM showed the microphase separated structure also occurred at the coat surface, especially at high PEG content, which could also be indirectly confirmed by the XPS and contact angle results. The formation mechanism of the microphase separated structure was discussed. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 1458–1465, 2007     

Surface functionalization of polypropylene by entrapment of polypropylene‐grafted‐poly(ethylene glycol)

A surface functionalization polypropylene was prepared by entrapment a copolymer of polypropylene‐grafted‐poly(ethylene glycol) into polypropylene. The effects of structure of copolymer, contact dies, and content of modifiers were studied. The results of attenuated total reflection infrared spectroscopy(ATR‐FTIR) and contact angle measurements indicated that PP‐g‐PEG could preferably diffuse onto the surface and effectively increase the hydrophilicity of PP. PPw‐g‐PEG with lower PEG contents, lower molecular weight of PPw and PEG had better selective enrichment on the surface of PP blend film. By grafting of PEG‐OH onto the MPP, PP macromolecular surface modifier with better solvent‐resistance than that of PEG can be achieved. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Wettability of poly(ethylene terephthalate) film treated with low‐temperature plasma and their surface analysis by ESCA

The surface of poly(ethylene terephthalate) (PET) film was modified by low‐temperature plasma with O₂, N₂, He, Ar, H₂, and CH₄ gases, respectively. After being treated by low‐temperature plasma, their surface wettability and chemical composition were investigated by means of electron spectroscopy for chemical analysis (ESCA) and contact angle measurement. The result shows that the surface wettability of PET can be improved by low‐temperature plasma, and the effect of the modification is due mainly to the kind of the gases. Mainly because of the contribution of hydrogen bonding force γ[STACK]^c_S[ENDSTACK], the surface wettability of PET treated with O₂, N₂, He, and Ar plasma for a short time (3 min) increase sharply, and the surface wettability is also improved by H₂ plasma treatment; but the CH₄ plasma treatment does not improve the wettability of PET. ESCA shows that the effect of wettability of PET is tightly related to the presence of polar functional groups that reside in the outermost surface layer of PET. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 72: 1327–1333, 1999     

Surface modification of a biomedical poly(ester)urethane by several low‐powered gas plasmas

Several low‐powered gas plasmas were employed to treat a biomedical poly(ester)urethane using the treatment gases of CO₂, O₂, NH₃, and SO₂ with different treatment time (2, 5, 10, and 15 min). The changes of the physical and chemical characteristics of the biopolymer surface were studied. Surface morphology was evaluated by scanning probe microscopy, which showed increased roughness of the surface after plasma treatment. The wettability of the surface was examined by static water contact angle (SCA) measurements, which presented that there was a decrease of SCA in all plasma treatments compared with the untreated surface and that each gas plasma had an optimum treatment time accompanied by a minimum contact angle. X‐ray photoelectron spectroscopy indicated the changes of the surface functional groups. The data demonstrated that CO₂ and O₂ plasmas resulted in the incorporation of oxygen‐containing groups, while NH₃ plasma resulted in the combination of nitrogen‐containing groups, and SO₂ plasma resulted in the formation of sulfur‐containing groups. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 1273–1282, 2006     

Synthesis and characterization of comb‐like polymer PVC–poly(ethylene oxide)

A new series of amphiphilic graft‐copolymers, composed of poly(vinyl chloride) (PVC) backbones and poly(ethylene oxide) side chains, was synthesized by chemical modification of PVC. The synthesis was based on the reaction between chlorine in PVC (polymerization degree 700) and sodium salt of polyethylene glycol (PEG). PEGs with molecular weights of 200 and 600 were used. The graft polymers were characterized by IR and gel permeation chromatography and the molecular parameters such as the average numbers of grafting chains on the PVC backbones were calculated as well as the grafting percent. The molecular weights of PEG were found to influence the rate of the grafting reaction and the final degree of conversion. The maximum grafting percentage of the resulted polymers after the purification was ca. 34%, regardless of the molecular weight of PEG. No gel was observed in the PVC‐g‐PEOs, in spite of the average numbers of grafting chains up to 32. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 75: 475–479, 2000     

Surface graft copolymerization of acrylic acid onto corona-treated poly(ethylene terephthalate) fabric

Acrylic acid (AA) was grafted onto the surface of poly(ethylene terephthalate) (PET) fabric after having short-time corona-discharge treatment (CDT) in an atmosphere in the presence of the initiator. The effect of N,N-dimethylformamide (DMF) pretreatment time, CDT time, graft copolymerization time and temperature, concentration of AA, and the content of initiator on graft yield of PET fabric was discussed. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 73: 1161–1164, 1999     

Mesoporous carbon membranes from polyimide blended with poly(ethylene glycol)

The control of the mesoporous structure in a carbon membrane from a poly(ethylene glycol)/polyimide‐blended polymer was investigated. The size of the pores tends to become large with increase of the content of poly(ethylene glycol) against polyimide, that is, the mesoporous structure could be controlled by the composition of the blended polymers. On the other hand, the average molecular weight of poly(ethylene glycol) has little effect from the viewpoint of the control of the pore structure. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 79: 836–841, 2001     

Effect of poly(ethylene glycol) on the solid‐state polymerization of poly(ethylene terephthalate)

Poly(ethylene glycol) (PEG) and end‐capped poly(ethylene glycol) (poly(ethylene glycol) dimethyl ether (PEGDME)) of number average molecular weight 1000 g mol^?1 was melt blended with poly(ethylene terephthalate) (PET) oligomer. NMR, DSC and WAXS techniques characterized the structure and morphology of the blends. Both these samples show reduction in T_g and similar crystallization behavior. Solid‐state polymerization (SSP) was performed on these blend samples using Sb₂O₃ as catalyst under reduced pressure at temperatures below the melting point of the samples. Inherent viscosity data indicate that for the blend sample with PEG there is enhancement of SSP rate, while for the sample with PEGDME the SSP rate is suppressed. NMR data showed that PEG is incorporated into the PET chain, while PEGDME does not react with PET. Copyright © 2005 Society of Chemical Industry     

Synthesis of amphiphilic poly(phthalazinone ether sulfone ketone)‐graft‐poly(ethylene glycol) graft copolymers via Williamson etherification

Amphiphilic graft copolymers consisting of poly(phthalazinone ether sulfone ketone) (PPESK) backbones and poly(ethylene glycol) (PEG) side chains were synthesized via reaction of chloromethylated PPESK (CMPPESK) with a sodium alkoxide of methoxyl PEG (PEG‐ ONa). The reactive precursor, CMPPESK, was prepared by the chloromethylation of PPESK with chloromethylether (CME) using concentrated H₂SO₄ as reaction medium. FTIR spectroscopy, ¹H‐NMR and Solid‐state ¹³C CP‐MAS NMR analysis confirmed the covalent linking of PEG with PPESK backbones. The PEG content in the graft copolymers from ¹H‐NMR analysis varied from 21.0 to 37.2 wt %, which was approximately in agreement with that calculated from TGA tests. The graft products have good solubility in many aprotic polar solvents and can be slightly swelled by water and ethanol, but water insoluble. Contact angle measurements revealed that the hydrophilicity of PPESK was significantly improved by the introduction of PEG graft chains, indicating the graft copolymer is a potential hydrophilic additive for PPESK membranes. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007.     

A novel method of surface modification on thin-film composite reverse osmosis membrane by grafting poly(ethylene glycol)

A novel method of surface modification by grafting hydrophilic poly(ethylene glycol) (PEG) chains onto the surface of a thin-film composite (TFC) polyamide reverse osmosis (RO) membrane was performed. Aminopolyethylene glycol monomethylether (MPEG-NH₂) was used as grafting monomer. The membranes were characterized by attenuated total reflectance Fourier transform infrared spectroscopy (ATR-FTIR), X-ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM). The changes in chemical composition and morphology of the membranes' surface indicated the successful grafting process. Furthermore, a preliminary experiment confirmed that the grafting of PEG chains improved membrane antifouling property.     

Formation of honeycomb films from poly(L‐lactide)‐block‐poly(ethylene glycol) via water‐droplet templating

The fabrication of honeycomb‐patterned films from amphiphilic poly(L ‐lactide)‐block‐poly(ethylene glycol) (PLEG) in a high‐humidity atmosphere is reported. The influence of the solution concentration on pattern formation was investigated. Moreover, by comparing the different conditions of fabricating regular structures between PLEG and poly(phenylene oxide), the mechanism of the regular pattern formation was studied. Finally, by adding sodium dodecylsulfate to a concentrated solution of 1 g L^?1 PLEG? CHCl₃ which otherwise could not form regular pores, we found that regular pores could be obtained. The PLEG honeycomb films are expected to be of use in cell culture, tissue engineering and many other areas. Copyright © 2007 Society of Chemical Industry     

Biodegradability of poly(ethylene terephthalate) copolymers with poly(ethylene glycol)s and poly(tetramethylene glycol)

Poly(ethylene terephthalate) copolymers were prepared by melt polycondensation of dimethyl terephthalate and excess ethylene glycol with 10–40mol% (in feed) of poly(ethylene glycol) (E) and poly(tetramethylene glycol) (B), with molecular weight (MW) of E and B 200–7500 and 1000, respectively. The reduced specific viscosity of copolymers increased with increasing MW and content of polyglycol comonomer. The temperature of melting (T_m), cold crystallization and glass transition (T_g) decreased with the copolymerization. T_m depression of copolymers suggested that the E series copolymers are the block type at higher content of the comonomer. T_g was decreased below room temperature by the copolymerization, which affected the crystallinity and the density of copolymer films. Water absorption increased with increasing content of comonomer, and the increase was much higher for E1000 series films than B1000 series films. The biodegradability was estimated by weight loss of copolymer films in buffer solution with and without a lipase at 37°C. The weight loss was enhanced a little by the presence of a lipase, and increased abruptly at higher comonomer content, which was correlated to the water absorption and the concentration of ester linkages between PET and PEG segments. The weight loss of B series films was much lower than that of E series films. The abrupt increase of the weight loss by alkaline hydrolysis is almost consistent with that by biodegradation.     

Surface modification of polypropylene membrane by low‐temperature plasma treatment

Microporous polypropylene membranes were low temperature plasma treated with acrylic acid and allylamine. Parameters of plasma treatment were examined and optimized for the enhancement of membrane performance properties. Excess power damaged the membrane surface and excess monomer flow rate increased the reactor pressure to interfere with the glow discharge. Longer plasma treatment time resulted in even more plasma coating and micropore blocking. The contact angle with water decreased and wettabilities increased with the increase of plasma treatment time. Deposition of the plasma polymer on the membrane surface was confirmed by FTIR/ATR spectra of the treated surface. In determining the flux, the hydrophilicity of the surface played a role as important as that of the micropore size. Adequate plasma treatment could enhance both water flux and solute removal efficiency. Results from the BSA (bovine serum albumin) solution test confirmed that fouling was greatly reduced after the plasma treatment. The BSA solution flux through the plasma‐treated membranes depended on pH, whereas pH variation had no serious effects on the untreated membrane. Modification of the surface charge by the plasma treatment should exert a substantial influence on the adsorption and removal of BSA. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 1555–1566, 2001     

Synthesis and characterization of novel block copolymer from trans‐4‐hydroxy‐L‐proline and poly(ethylene glycol)

A series of novel ABA‐type block copolymers were synthesized by polymerization of trans‐4‐hydroxy‐L ‐proline (HyP) in the presence of various molecular weight poly(ethylene glycol)s (PEGs), a bifunctional OH‐terminated PEG using stannous octoate as catalyst. The optimal reaction conditions for the synthesis of the copolymers were obtained with 5 wt % stannous octoate at 140°C under vacuum (20 mmHg) for 24 h. The synthesized copolymers were characterized by IR spectroohotometry, proton nuclear magnetic resonance, differential scanning calorimetry, and Ubbelohde viscometer. The glass transition temperature (T_g) of the copolymers shifted to significantly higher temperature with increasing the number average degree of polymerization and HyP/PEO molar ratio. In contrast, the melting temperature (T_m) decreased with increasing the HyP/PEO molar ratio. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 1581–1587, 2001     

Preparation of protein microarrays on non‐fouling and hydrated poly(ethylene glycol) hydrogel substrates using photochemical surface modification

BACKGROUND: Conventional protein microarrays prepared on hard, dry substrates, such as glass and silicone, have several limitations, as proteins may easily denature and lose their structure. To overcome such problems, the fabrication of wet protein microarrays on non‐fouling and hydrated PEG‐based hydrogels was investigated. RESULT: Bovine serum albumin (BSA) and glucose oxidase (GOX), chosen as model proteins, were covalently immobilized on PEG hydrogel surfaces via 5‐azidonitrobenzoyloxy N‐hydroxysuccinimide, a photoreactive bifunctional linker. Successful fixation of the bifunctional linker and subsequent immobilization of the proteins on the PEG hydrogel surfaces were confirmed with X‐ray photoelectron spectroscopy (XPS) and Fourier transform infrared spectroscopy (FTIR) studies. GOX immobilized on the hydrogel surface maintained approximately 50% of its initial activity after 24 h when left in dry conditions, but maintained only 20% when immobilized on a dry substrate. Photochemical fixation combined with photolithography produced well‐defined protein micropatterns with sizes ranging from 50–500 µm, and molecular recognition‐mediated specific binding between biotin and streptavidin was successfully assayed using microarrays on PEG hydrogels. CONCLUSION: A protein‐repellent PEG hydrogel surface was photochemically modified to covalently immobilize proteins and create protein microarrays. The use of hydrated hydrogels as substrates for protein microarrays could minimize the deactivation of proteins in dry conditions, and the non‐fouling property of PEG hydrogels allows the passivation step of protein microarray preparation to be skipped. Copyright © 2008 Society of Chemical Industry     

Crystallization behavior of biodegradable amphiphilic poly(ethylene glycol)‐poly(L‐lactide) block copolymers

Poly(ethylene glycol)‐poly(L ‐lactide) diblock and triblock copolymers were prepared by ring‐opening polymerization of L ‐lactide with poly(ethylene glycol) methyl ether or with poly(ethylene glycol) in the presence of stannous octoate. Molecular weight, thermal properties, and crystalline structure of block copolymers were analyzed by ¹H‐NMR, FTIR, GPC, DSC, and wide‐angle X‐ray diffraction (WAXD). The composition of the block copolymer was found to be comparable to those of the reactants. Each block of the PEG–PLLA copolymer was phase separated at room temperature, as determined by DSC and WAXD. For the asymmetric block copolymers, the crystallization of one block influenced much the crystalline structure of the other block that was chemically connected to it. Time‐resolved WAXD analyses also showed the crystallization of the PLLA block became retarded due to the presence of the PEG block. According to the biodegradability test using the activated sludge, PEG–PLLA block copolymer degraded much faster than PLLA homopolymers of the same molecular weight. © 1999 John Wiley amp; Sons, Inc. J Appl Polym Sci 72: 341–348, 1999     

Synthesis and characterization of poly(L‐lactide)‐poly(ethylene glycol) multiblock copolymers

Poly(L‐lactide)‐poly(ethylene glycol) multiblock copolymers with predetermined block lengths were synthesized by polycondensation of PLA diols and PEG diacids. The reaction was carried out under mild conditions, using dicyclohexylcarbodiimide as the coupling agent and dimethylaminopyridine as the catalyst. The resulting copolymers were characterized by various analytical techniques, such as GPC, viscometry, ¹H‐NMR, FTIR, DSC, X‐ray diffractometry, and contact angle measurement. The results indicated that these copolymers presented outstanding properties pertinent to biomedical use, including better miscibility between the two components, low crystallinity, and hydrophilicity. Moreover, the properties of the copolymers can be modulated by adjusting the block length of the two components or the reaction conditions. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 1729–1736, 2002; DOI 10.1002/app.10580     

Surface immobilization of star‐shaped poly(ethylene oxide) on poly(dimethylsiloxane)

A thin layer of star‐shaped poly(ethylene oxide) (PEO) (starPEO), on the polydimethylsiloxane (PDMS) membrane was prepared by a simple immobilization procedure. Photoreactive molecules were introduced on the surface of the polymeric support to achieve the formation of thin starPEO film from the materials having no functional groups. This novel technique enabled us to immobilize any kind of chemical, especially one that had no functional groups, and readily to control the amount of immobilization. The gas permeation properties of the starPEO‐immobilized PDMS membranes were investigated for pure propane and propylene. The permeance of gases were found to decrease in the starPEO‐immobilized PDMS membranes, although the ideal separation factors for propylene/propane were increased with the loading amount of silver ions, because of the facilitation action of silver ions in the immobilized PEO unit on the PDMS membranes, as propylene carriers. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 2369–2373, 2002