Synthesis,characterization, and properties of low viscosity tetra‐functional epoxy resin N,N,N′,N′‐ tetraglycidyl‐3,3′‐diethyl‐4,4′‐diaminodiphenylmethane

Tetra‐functional epoxy resin N,N,N′,N′‐tetraglycidyl‐3,3′‐diethyl‐4,4′‐diaminodiphenylmethane (TGDEDDM) was synthesized and characterized. The viscosity of TGDEDDM at 25°C was 7.2 Pa·s, much lower than that of N,N,N′,N′‐tetraglycidyl‐4,4′‐diaminodiphenylmethane (TGDDM). DSC analysis revealed that the reactivity of TGDEDDM with curing agent 4,4′‐diamino diphenylsulfone (DDS) was significantly lower than that of TGDDM. Owing to its lower viscosity and reactivity, TGDEDDM/DDS exhibited a much wider processing temperature window compared to TGDDM/DDS. Trifluoroborane ethylamine complex (BF₃‐MEA) was used to promote the curing of TGDEDDM/DDS to achieve a full cure, and the thermal and mechanical properties of the cured TGDEDDM were investigated and compared with those of the cured TGDDM. It transpired that, due to the introduction of ethyl groups, the heat resistance and flexural strength were reduced, while the modulus was enhanced. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2014 , 131, 40009.     

Hydrodynamic properties for N,N,N′,N′‐tetraalkyl diglycolamides dissolved in n‐dodecane system

N,N,N′,N′‐tetraoctyl diglycolamide (TODGA) and N,N,N′,N′‐tetra(2‐ethylhexyl) diglycolamide (T2EHDGA) have been identified as promising extractants for actinide partitioning from high‐level nuclear waste. These extractants are proposed to be used along with suitable phase modifiers, viz. N,N‐dihexyl octanamide (DHOA), tri‐n‐butyl phosphate (TBP) and 2‐decanol dissolved in n‐dodecane. Hydrodynamic parameters, viz. density, viscosity and interfacial tension (IFT) are important for optimisation of hydrometallurgical process to ensure that there is no emulsion formation and to achieve desired phase disengagement rate. Densities and viscosities of the two extractants, viz. TODGA and T2EHDGA along with different phase modifiers have been measured over different range of compositions and temperatures (298–333 K). The viscosity data have been used to calculate the activation energy for viscous flow for each composition of solvents. The IFT values have also been measured for different solvent compositions. The viscosity and IFT data of TODGA and T2EHDGA with 2‐decanol as phase modifier appears suitable under hydrometallurgical conditions proposed for actinide partitioning. © 2011 Canadian Society for Chemical Engineering     

Combustion Properties of Amino‐Substituted Guanidinium 4,4′,5,5′‐Tetranitro‐2,2′‐biimidazolate(N4BIM) Salts

This paper describes the combustion properties of the amino‐substituted guanidinium 4,4′,5,5′‐tetranitro‐2,2′‐biimidazolate (N4BIM) series, including the bis‐mono, di and triaminoguanidinium salts. These salts are of interest as propellant ingredient additives, and in particular, the bis‐triaminoguanidinium salt of N4BIM displays excellent burn rate and combustion behavior. Our combustion studies have shown that TAGN4‐BIM displays a fast burning rate and has the lowest pressure dependence exponent yet measured for a triaminoguanidinium salt.     

Crystallography and Structure–Property Relationships in 2,2′,2″,2′′′,4,4′,4″,4′′′,6,6′,6″,6′′′‐Dodecanitro‐1,1′ : 3′1″ : 3″,1′′′‐ Quaterphenyl (DODECA)

X‐ray crystallographic study of 2,2′,2″,2′′′,4,4′,4″,4′′′,6,6′,6″,6′′′‐dodecanitro‐1,1′ : 3′1″ : 3″,1′′′‐quaterphenyl (DODECA) has been carried out. Nonbonding interatomic distances of oxygen atoms inside of all the nitro groups are shorter than those corresponding to the intermolecular contact radii for oxygen. By means of the DFT B3LYP/6‐31(d, p) method a difference of 136 kJ mol⁻¹ between the X‐ray and DFT structures of DODECA was found. The bearer of the highest initiation reactivity in its molecule in solid phase should be the nitro group at 4′′′‐position, in contrast to those at 2′‐ or 2″‐positions in its isolated molecule. The most reactive nitro group in the DODECA molecule can be well specified by the relationship between net charges on nitro groups and charges on their nitrogen atoms, both of them for the X‐ray structure. The ¹⁵N chemical shift, corresponding to this nitro group for the initiation by impact and shock, correlates very well with these shifts of the reaction centers of the other six “genuine” polynitro arenes.     

α-Substituierte Phosphonate. XXXI. Zur Reaktion von N,N,N′,N′-Tetramethylchlorformamidiniumchlorid mit P-III-Verbindungen

α-Substituted Phosphonates. XXXI. The Reaction of N,N,N′,N′-Tetramethyl Chloroformamidinium Chloride with P(III) Compounds N,N,N′,N′-Tetramethyl chloroformamidiniumchloride ( 4 ) does not react with triethyl phosphite (TEP) or isopropyl diphenylphosphinate to give the expected bisphosphoryl derivatives 7 and 11 , respectively, but primarily the monophosphorylated amidinium salts 6 and 10 respectively. The phosphine oxide 10 is stable, while 6 undergoes an elimination of ethyl chloride to the betain 8 . Even under more drastic conditions the reaction of 4 or 8 with TEP does not lead to the expected bis(dimethylamino)bisphosphonate 7 , but to the monoaminated bisphosphonate 1 , involving a reduction step. Similar reduction has been observed under mild conditions in Michaelis-Arbusov reaction of dichloromethylenimonium chloride, yielding the expected trisphosphonate 2 and the bisphosphonate 1 as a by-product.     

Synthesis and Energetic Properties of 4,4′,5,5′‐Tetranitro‐2,2′‐biimidazolate(N4BIM) Salts

This paper describes the synthesis and characterization of several salts of 4,4′,5,5′‐tetranitro‐2,2′‐biimidazolate (N4BIM). Each of the salts were characterized chemically, thermally, morphologically, as well as with respect to destructive stimuli (impact, electrostatic discharge, friction, thermal). These salts show promise as propellant ingredient additives, and in particular, the bis‐triaminoguanidinium salt of N4BIM displays excellent burn rate and combustion behavior. Our combustion studies have shown that TAGN4BIM displays a fast burning rate and has the lowest pressure dependence exponent yet measured for a triaminoguanidinium salt.     

Water Solvent Method for Esterification and Amide Formation between Acid Chlorides and Alcohols Promoted by Combined Catalytic Amines: Synergy between N‐Methylimidazole and N,N,N′,N′‐Tetramethylethylenediamine (TMEDA)

An efficient method for esterification between acid chlorides and alcohols in water as solvent has been developed by combining the catalytic amines, N‐methylimidazole and N,N,N′,N′‐tetramethylethylenediamine (TMEDA). The present Schotten–Baumann‐type reaction was performed by maintaining the pH at around 11.5 using a pH controller to prevent the decomposition of acid chlorides and/or esters and to facilitate the condensation. The choice of catalysts (0.1 equiv.) was crucial: the combined use of N‐methylimidazole and TMEDA exhibited a dramatic synergistic effect. The catalytic amines have two different roles: (i) N‐methylimidazole forms highly reactive ammonium intermediates with acid chlorides and (ii) TMEDA acts as an effective HCl binder. The production of these intermediates was rationally supported by a careful ¹H NMR monitoring study. Related amide formation was also achieved between acid chlorides and primary or secondary amines, including less nucleophilic or water‐soluble amines such as 2‐(or 4‐)chloroaniline, the Weinreb N‐methoxyamine, and 2,2‐dimethoxyethanamine.     

Microwave‐assisted and conventional polycondensation reaction of optically active N,N′‐(4,4′‐sulphonediphthaloyl)‐bis‐L‐leucine diacid chloride with aromatic diamines

3,3′,4,4′‐Diphenylsulfonetetracarboxylic dianhydride ( 1 ) was reacted with L‐leucine ( 2 ) in acetic acid and the resulting imide‐acid ( 3 ) was obtained in high yield. The diacid chloride ( 4 ) was prepared from diacid derivative ( 3 ) by reaction with thionyl chloride. The polycondensation reaction of diacid chloride ( 4 ) with several aromatic diamines such as 4,4′‐sulfonyldianiline ( 5a ), 4,4′‐diaminodiphenyl methane ( 5b ), 4,4′‐diaminodiphenylether ( 5c ), p‐phenylenediamine ( 5d ), m‐phenylenediamine ( 5e ), 2,4‐diaminotoluene ( 5f ), and 1,5‐diaminonaphthalene ( 5g ) was developed by using a domestic microwave oven in the presence of a small amount of a polar organic medium such as o‐cresol. The polymerization reactions were also performed under two conventional methods: low temperature solution polycondensation in the presence of trimethylsilyl chloride, and a short period reflux conditions. A series of optically active poly(amide‐imide)s with inherent viscosity of 0.25–0.42 dL/g were obtained with high yield. All of the above polymers were fully characterized by IR, elemental analyses, and specific rotation techniques. Some structural characterizations and physical properties of these optically active poly (amide‐imide) s are reported. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91: 2992–3000, 2004     

Synthesis and properties of organosoluble polyimides derived from 2,2′‐dibromo‐ and 2,2′,6,6′‐tetrabromo‐4,4′‐oxydianilines

Two new aromatic diamines, 2,2′‐dibromo‐4,4′‐oxydianiline (DB‐ODA 4 ) and 2,2′,6,6′‐tetrabromo‐4,4′‐oxydianiline (TB‐ODA 5 ), have been synthesized by oxidation, bromination, and reduction of 4,4′‐oxydianiline (4,4′‐ODA). Novel polyimides 6a–f and 7a–f were prepared by reacting DB‐ODA ( 4 ) and TB‐ODA ( 5 ) with several dianhydrides by one‐step method, respectively. The inherent viscosities of these polyimides ranged from 0.31 to 0.99 dL/g (0.5 g/dL, in NMP at 30°C). These polyimides showed enhanced solubilities compared to those derived from 4,4′‐oxydianiline and corresponding dianhydrides. Especially, polyimides 7a , derived from rigid PMDA and TB‐ODA ( 5 ) can also be soluble in THF, DMF, DMAc, DMSO, and NMP. These polyimides also exhibited good thermal stability. Their glass transition temperatures measured by thermal mechanical analysis (TMA) ranged from 251 to 328°C. When the same dianhydrides were used, polyimides 7 containing four bromide substituents had higher glass transition temperatures than polyimides 6 containing two bromide substituents. The effects of incorporating more polarizable bromides on the refractive indices of polyimides were also investigated. The average refractive indices (n_av) measured at 633 nm were from 1.6088 to 1.7072, and the in‐plane/out‐of‐plane birefringences (Δn) were from 0.0098 to 0.0445. It was found that the refractive indices are slightly higher when polyimides contain more bromides. However, this effect is not very obvious. It might be due to loose chain packing resulted from bromide substituents at the 2,2′ and 2,2′,6,6′ positions of the oxydiphenylene moieties. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Synthesis and spectroelectrochemistry of dithieno(3,2‐b:2′,3′‐d)pyrrole derivatives

New π‐conjugated polymers containing dithieno(3,2‐b:2′,3′‐d)pyrrole (DTP) were successfully synthesized via electropolymerization. The effect of structural differences on the electrochemical and optoelectronic properties of the 4‐[4H‐dithieno(3,2‐b:2′,3′‐d)pyrrol‐4‐yl]aniline (DTP–aryl–NH₂), 10‐[4H‐dithiyeno(3,2‐b:2′,3′‐d)pirol‐4‐il]dekan‐1‐amine (DTP–alkyl–NH₂), and 1,10‐bis[4H‐dithieno(3,2‐b:2′,3′‐d)pyrrol‐4‐yl] decane (DTP–alkyl–DTP) were investigated. The corresponding polymers were characterized by cyclic voltammetry, NMR (¹H‐NMR and ¹³C‐NMR), and ultraviolet–visible spectroscopy. Changes in the electronic nature of the functional groups led to variations in the electrochemical properties of the π‐conjugated systems. The electroactive polymer films revealed redox couples and exhibited electrochromic behavior. The replacement of the DTP–alkyl–DTP unit with DTP–aryl–NH₂ and DTP–alkyl–NH₂ resulted in a lower oxidation potential. Both the poly(10‐(4H‐Dithiyeno[3,2‐b:2′,3′‐d]pirol‐4‐il)dekan‐1‐amin) (poly(DTP–alkyl–NH₂)) and poly(1,10‐bis(4H‐dithieno[3,2‐b:2′,3′‐d]pyrrol‐4‐yl) decane) (poly(DTP–alkyl–DTP)) films showed multicolor electrochromism and also fast switching times (<1 s) in the visible and near infrared regions. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40701.     

Syntheses and Analyses of N,N′‐Dinitrourea

N,N′‐Dinitrourea was prepared through nitration of urea at low temperature in mixed acids in 67 % yield. The prepared material was pure and found to be stable at room temperature. The properties of N,N′‐dinitrourea were analysed by: TG, DSC, ignition test in Wood's metal bath, NMR, MS, FT‐IR, gaspycnometry and BAM impact and friction sensitivity tests. N,N′‐Dinitrourea was found to have a very high density and positive oxygene balance. It was, however, found to be sensitive both to impact and friction.     

Synthesis of Substituted 2,2′‐Bipyridines and 2,2′:6′,2′′‐Terpyridines by Cobalt‐Catalyzed Cycloaddition Reactions of Nitriles and α,ω‐Diynes with Exclusive Regioselectivity

A variety of substituted 2,2′‐bipyridines were synthesized by a 1,2‐bis(diphenylphosphino)ethane (dppe)/cobalt chloride hexahydrate (CoCl₂⋅6 H₂O)/zinc‐catalyzed [2+2+2] cycloaddition reaction of diynes and nitriles, with all reactions exhibiting exclusive regioselectivity. Thus, symmetrical and unsymmetrical 1,6‐diynes and 2‐cyanopyridine reacted in the presence of 5 mol % of dppe, 5 mol % of CoCl₂⋅6 H₂O and 10 mol % of zinc powder to provide the corresponding 2,2′‐bipyridines. Under identical reaction conditions, 1‐(2‐pyridyl)‐1,6‐diynes and nitriles reacted smoothly with exclusive regioselectivity to produce 2,2′‐bipyridines in good yield. 2,2′‐Bipyridines were also obtained by the double [2+2+2] cycloaddition reaction of 1,6,8,13‐tetraynes with nitriles. Similarly, 2,2′:6′,2′′‐terpyridines were synthesized from 1‐(2‐pyridyl)‐1,6‐diyne and 2‐cyanopyridine. The regiochemistry observed can be explained by considering the electronic nature of cobaltacyclopentadiene intermediates and nitriles. A survey of the exclusive regiochemical trend gives reasonable credence to the synthetic potential of the present method.     

Crystallography and Structure–Property Relationships of 2,2″,4,4′,4″,6,6′,6″‐Octanitro‐1,1′ : 3′,1″‐Terphenyl (ONT)

An X‐ray crystallographic study of 2,2″,4,4′,4″,6,6′,6″‐octanitro‐1,1′ : 3′,1″‐terphenyl (ONT) has been carried out. The dihedral angles between benzene rings vary from 84.9° to 89.4°. Nonbinding interatomic distances of oxygen atoms inside all the nitro groups are shorter than the intermolecular contact radii for oxygen. On the basis of the DFT B3LYP/6‐31(d, p) method it was found that the difference between the X‐ray structure in the solid phase and DFT result for the gas phase is 98 kJ mol⁻¹, and the bearer of the highest initiation reactivity of the ONT molecule in the solid phase should be the nitro group at 4″‐position, in contrast to those at 4′‐ or 6′‐position that play this role in the isolated molecule. It has been stated that the nitro groups at the reaction centers of the ONT molecule are relatively well specified by their ¹⁵N NMR chemical shifts.     

Synthesis of 3,3′-Bis(2,2′,4,4′,6,6′-Hexanitortilbene)

This paper describes the synthesis of 3,3′bis(2,2′,4,4′,6,6′-hexanitrostilbene) (5). Based on the Ullmann reaction we prepared the title compound in nitrobenzene by using 3-chloro 2,2′,4,4′,6,6′-hexanitroztilbene (4) as the starting material and copper powder as the catalyst. (4) was reacted with hydrazine, not to yield a desired product, azo-3,3′bist(2,2′,4,4′,6,6′-hexanitrostilbene.) but to form a well-known explosive, 2,2′,4,4′,6,6′-hexanitrostibene (6). Differential scanning calorimetrical analysis has shown that (5) begins to decompose at the temperature of 298°C.     

Organosoluble polyimides derived from asymmetric 2‐substituted‐and 2,2′,6‐trisubstituted‐4,4′‐oxydianilines

We report a new method for the preparation of asymmetric diamines using 4,4′‐oxydianiline (4,4′‐ODA) as the starting material. By controlling the equivalents of bromination agent, N‐bromosuccinimide, we were able to attach bromide and phenyl substituents at the 2‐ or 2,2′,6‐positions of 4,4′‐ODA. Thus, four new asymmetric aromatic diamines, 2‐bromo‐4,4′‐oxydianiline (6), 2,2′,6‐tribromo‐4,4′‐oxydianiline (7), 2‐phenyl‐4,4′‐oxydianiline (8) and 2,2′,6‐triphenyl‐4,4′‐oxydianiline (9), were synthesized by this method. Their structural asymmetry was confirmed using ¹H NMR spectroscopy. Asymmetric polyimides (PI10–PI13) were prepared from these diamines and three different dianhydrides (pyromellitic dianhydride (PMDA), 3,3′,4,4′‐biphenyltetracarboxylic dianhydride and 2,2‐bis(3,4‐dicarboxyphenyl)hexafluoropropane dianhydride) in refluxing m‐cresol. The formed polyimides, except PI10a derived from 6 and PMDA, were all soluble in m‐cresol without premature precipitation during polymerization. These polyimides with inherent viscosity of 0.41–0.96 dL g^?1, measured at a concentration of 0.5 g dL^?1 in N‐methyl‐2‐pyrrolidone at 30 °C, can form tough and flexible films. Because of the structural asymmetry, they also exhibited enhanced solubility in organic solvents. Especially, polyimides PI11a and PI13a derived from 7 and 9 with rigid PMDA were soluble in various organic solvents at room temperature. The structural asymmetry of the prepared polyimides was also evidenced from ¹H NMR spectroscopy. In the ¹H NMR spectrum of PI11a, the protons of pyromellitic moiety appeared in an area ratio of 1:2:1 at three different chemical shifts, which were assigned to head‐to‐head, head‐to‐tail and tail‐to‐tail configurations, respectively. These polyimides also exhibited good thermal stability. Their glass transition temperatures ranged from 297 to 344 °C measured using thermal mechanical analysis. © 2013 Society of Chemical Industry     

Synthesis and properties of new aromatic polyimides based on 2,2′‐dibromo‐4,4′,5,5′‐benzophenone tetracarboxylic dianhydride

New polyimides with enhanced thermal stability and high solubility were synthesized in common organic solvents from a new dianhydride, 2,2′‐dibromo‐4,4′,5,5′‐benzophenone tetracarboxylic dianhydride (DBBTDA). DBBTDA was used as monomer to synthesize polyimides by using various aromatic diamines. The polymers were characterized by IR and NMR spectroscopy and elemental analysis. These polyimides had good inherent viscosities in N‐methyl‐2‐pyrrolidinone (NMP) and also high solubility and excellent thermo‐oxidative stability, with 5 % weight loss in the range 433 to 597 °C. Copyright © 2004 Society of Chemical Industry     

Discovery of 5′′‐Chloro‐N‐[(5,6‐dimethoxypyridin‐2‐yl)methyl]‐2,2′:5′,3′′‐terpyridine‐3′‐carboxamide (MK‐1064): A Selective Orexin 2 Receptor Antagonist (2‐SORA) for the Treatment of Insomnia

The field of small‐molecule orexin antagonist research has evolved rapidly in the last 15 years from the discovery of the orexin peptides to clinical proof‐of‐concept for the treatment of insomnia. Clinical programs have focused on the development of antagonists that reversibly block the action of endogenous peptides at both the orexin 1 and orexin 2 receptors (OX₁R and OX₂R), termed dual orexin receptor antagonists (DORAs), affording late‐stage development candidates including Merck’s suvorexant (new drug application filed 2012). Full characterization of the pharmacology associated with antagonism of either OX₁R or OX₂R alone has been hampered by the dearth of suitable subtype‐selective, orally bioavailable ligands. Herein, we report the development of a selective orexin 2 antagonist (2‐SORA) series to afford a potent, orally bioavailable 2‐SORA ligand. Several challenging medicinal chemistry issues were identified and overcome during the development of these 2,5‐disubstituted nicotinamides, including reversible CYP inhibition, physiochemical properties, P‐glycoprotein efflux and bioactivation. This article highlights structural modifications the team utilized to drive compound design, as well as in vivo characterization of our 2‐SORA clinical candidate, 5′′‐chloro‐N‐[(5,6‐dimethoxypyridin‐2‐yl)methyl]‐2,2′:5′,3′′‐terpyridine‐3′‐carboxamide (MK‐1064), in mouse, rat, dog, and rhesus sleep models.     

Studies on the Synthesis of 2,2′,4,4′,6,6′-Hexanitrostilbene

The synthesis of 2,2′,4,4′,6,6′-hexanitrostilbene by oxidative coupling of 2,4,6-trinitrotoluene in the presence of metal catalysts has been studied. The effects of reaction parameters on product yields have been evaluated and mechanisms for the reaction are proposed.     

Palladium‐Catalyzed N‐Arylation of N,N‐Dialkylhydrazines with Aryl Chlorides

N,N‐Dialkyl‐N′‐arylhydrazines have been prepared usually in high to excellent yields via the reaction of N,N‐dialkylhydrazines with aryl chlorides in the presence of Pd₂(dba)₃, Xphos and NaO‐t‐Bu in dioxane at 120 °C. With ortho‐substituted aryl chlorides best results have been obtained by using 2‐(2′,6′‐dimethoxybiphenyl)dicyclohexylphosphine (ligand d) as the ligand.     

Antioxidant mechanism of a 3‐arylbenzofuranone containing a 2′‐hydroxyl group

5‐Methyl‐7‐tert‐butyl‐3‐(2′hydroxyl‐5′‐methylphenyl)3H‐benzofuran‐2‐one (PCRBF2), is a better scavenger of 2,2‐diphenyl‐1‐picrylhydrazyl radicals than benzofuranone analogs without the 2′‐substituent, which indicates that PCRBF2 will cause good stabilization in polymers. To prove this further, antioxidation by PCRBF2 and other benzofuranone analogs, namely, 5‐methyl‐7‐tert‐butyl‐3‐(3′,4′‐dimethylphenyl)3H‐benzofuran‐2‐one (OXBF2) and 5‐methyl‐7‐tert‐butyl‐3‐(2′,5′‐dimethylphenyl)3H‐benzofuran‐2‐one (PXBF2), was comparatively studied in polypropylene. The resulting antioxidant activity order of these benzofuranones was PCRBF2 > OXBF2 > PXBF2, an observation showing that the hydroxyl group in the 2′‐position does not weaken the antioxidant activity of benzofuranone, but, on the contrary, increases it. Analyses by FTIR revealed intramolecular hydrogen bonding between the 3‐position hydrogen and the oxygen of the 2′‐hydroxyl group, which makes the 2′‐hydroxyl hydrogen of PCRBF2 more reactive than the 3‐position reactive hydrogen. Thus the hydroxyl group reacts with radicals first. J. VINYL ADDIT. TECHNOL., 19:198‐202, 2013. © 2013 Society of Plastics Engineers