Cationic copolymers of α,β‐poly‐(N‐2‐hydroxyethyl)‐DL‐aspartamide (PHEA) and α,β‐polyasparthylhydrazide (PAHy): synthesis and characterization

In the present study the derivatization of two water‐soluble synthetic polymers, α,β‐poly(N‐2‐hydroxyethyl)‐DL ‐aspartamide (PHEA) and α,β‐polyasparthylhydrazide (PAHy), with glycidyltrimethylammonium chloride (GTA) is described. This reaction permits the introduction of positive charges in the macromolecular chains of PHEA and PAHy in order to make easier the electrostatic interaction with DNA. Different parameters affect the reaction of derivatization, such as GTA concentration and reaction time. PHEA reacts partially and slowly with GTA; on the contrary the reaction of PAHy with GTA is more rapid and extensive. The derivatization of PHEA and PAHy with GTA is a convenient method to introduce positive groups in their chains and it permits the preparation of interpolyelectrolyte complexes with DNA. © 2000 Society of Chemical Industry     

Poly‐α,β‐(3‐hydroxypropyl)‐DL‐aspartamide: A new drug carrier

Poly‐α,β‐(3‐hydroxypropyl)‐DL ‐aspartamide (PHPA) was synthesized by the ring‐open reaction of polysuccinimide (PSI) and 3‐hydroxypropylamine. The polymer was characterized by ¹H‐NMR, ¹³C‐NMR, FTIR, and GPC. Mark–Houwink coefficients were obtained from viscometry and GPC measurements, K = 5.53 × 10⁻³ and α = 0.78 in water. The acute toxicity of PHPA was examined and it revealed no death in ICR mice up to the dose treated of 15.3 kg/kg, and hematological parameters showed no significant difference between treated and control animals. The potential use of PHPA as a drug carrier was also investigated. In a typical case, a contraceptive drug, norethindrone (NET), was bonded to PHPA, and the drug sustained released as long as 120 days an in vitro test. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 2411–2417, 2000     

Blends of bacterial poly[(R)‐3‐hydroxybutyrate] with oligo[(R,S)‐3‐hydroxybutyrate]‐diol

The miscibility, melting and crystallization behaviour of poly[(R)‐3‐hydroxybutyrate], PHB, and oligo[(R,S)‐3‐hydroxybutyrate]‐diol, oligo‐HB, blends have been investigated by differential scanning calorimetry: thermograms of blends containing up to 60 wt% oligo‐HB showed behaviour characteristic of single‐phase amorphous glasses with a composition dependent glass transition, T_g, and a depression in the equilibrium melting temperature of PHB. The negative value of the interaction parameter, determined from the equilibrium melting depression, confirms miscibility between blend components. In parallel studies, glass transition relaxations of different melt‐crystallized polymer blends containing 0–20 wt% oligo‐HB were dielectrically investigated between ?70 °C and 120 °C in the 100 Hz to 50 kHz range. The results revealed the existence of a single α‐relaxation process for blends, indicating the miscibility between amorphous fractions of PHB and oligo‐HB. © 2002 Society of Chemical Industry     

Preparation of electrorheological active ionomers from poly(2‐hydroxyethyl methacrylate)‐co‐poly(4‐vinyl pyridine)

In this study, synthesis, characterization, partial hydrolysis, and salt formation of poly(2‐hydroxyethyl methacrylate)‐co‐poly(4‐vinyl pyridine), (poly(HEMA)‐co‐poly‐(4‐VP)) copolymers were investigated. The copolymers were synthesized by free radical polymerization using K₂S₂O₈ as an initiator. By varying the monomer/initiator ratio, chain lengths of the copolymers were changed. The copolymers were characterized by gel permeation chromatography (GPC), viscosity measurements, ¹H and ¹³C NMR and FTIR spectroscopies, elemental analysis, and end group analysis methods. The copolymers were partially hydrolyzed by p‐toluene sulfonic acid monohydrate (PTSA·H₂O) and washed with LiOH_(aq) solution to prepare electrorheological (ER) active ionomers, poly(Li‐HEMA)‐co‐poly(4‐VP). © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 99: 3540–3548, 2006     

Surface‐active amphiphilic poly[(2‐acrylamido‐2‐methylpropanesulfonic acid)‐co‐(N‐isopropylacrylamide)] nanoparticles as stabilizer in aqueous emulsion polymerization

This work reports the effect of nanogel solid particles on the surface and interfacial tension of water/air and water/styrene interfaces. Moreover, the work aimed to use nanogels as a stabilizer for miniemulsion aqueous polymerization. A series of amphiphilic crosslinked N‐isopropylacrylamide (NIPAm) and 2‐acrylamido‐2‐methylpropanesulfonic acid (AMPS) copolymer nanogels were synthesized based on an aqueous copolymerization batch method. Divinylbenzene and N,N‐methylene bisacrylamide were used as crosslinkers. The morphologies of the prepared nanogels were investigated using transmission and scanning electron microscopies. The lower critical transition temperatures were determined using differential scanning calorimetry. The surface tension of colloidal NIPAm/AMPS dispersions was measured as functions of surface age, temperature and the morphology of the NIPAm/AMPS nanogels. The NIPAm/AMPS nanogels reduced the surface tension of water to about 30.1 mN m^?1 at 298 K with a small increase at 313 K. Surface activities of these nanogels in water were determined by surface tension measurements. The NIPAm/AMPS dispersions had high surface activity and were used as a stabilizer to prepare a crosslinked poly(styrene‐co‐AMPS) microgel based on emulsion crosslinking polymerization. © 2013 Society of Chemical Industry     

Shape memory properties and unusual optical behaviour of an interpenetrating network of poly(ethylene oxide) and poly(2‐hydroxyethyl methacrylate)

An interpenetrating polymer network (IPN) with shape memory properties was prepared by using poly(2‐hydroxyethyl methacrylate) (PHEMA) and poly(ethylene oxide) (PEO). PHEMA acts as a fixed phase and PEO as a switching phase. The switching action of PEO is due to the reversible process of melting and crystallization. It was observed that the shape recovery of the IPN increases with increasing crosslinker concentration up to an optimum value and decreases thereafter. In addition to the shape memory property, the IPNs show a reversible change in optical properties from translucent to opaque. The change in optical properties is quite different from that observed in a semicrystalline polymer system where the transparency increases as a result of the melting of crystals. This behaviour of the IPN is explained in terms of H‐bonding of PEO with PHEMA. Fourier transform infrared spectroscopy was used to study the H‐bonding between PEO and PHEMA. © 2019 Society of Chemical Industry     

DNA adsorption on a poly‐L‐lysine‐immobilized poly(2‐hydroxyethyl methacrylate) membrane

The DNA adsorption properties of poly‐L ‐lysine‐immobilized poly(2‐hydroxyethyl methacrylate) (pHEMA) membrane were investigated. The pHEMA membrane was prepared by UV‐initiated photopolymerization and activated with epichlorohydrin. Poly‐L ‐lysine was then immobilized on the activated pHEMA membrane by covalent bonding, via a direct chemical reaction between the amino group of poly‐L ‐lysine and the epoxy group of pHEMA. The poly‐L ‐lysine content of the membrane was determined as 1537 mg m^?2. The poly‐L ‐lysine‐immobilized membrane was utilized as an adsorbent in DNA adsorption experiments. The maximum adsorption of DNA on the poly‐L ‐lysine‐immobilized pHEMA membrane was observed at 4 °C from phosphate‐buffered salt solution (pH 7.4, 0.1 M; NaCl 0.5 M) containing different amounts of DNA. The non‐specific adsorption of DNA on the plain pHEMA membrane was low (about 263 mg m^?2). Higher DNA adsorption values (up to 5849 mg m^?2) were obtained in which the poly‐L ‐lysine‐immobilized pHEMA membrane was used. Copyright © 2003 Society of Chemical Industry     

Preparation of poly(styrene‐b‐2‐hydroxyethyl acrylate) block copolymer using reverse iodine transfer polymerization

Reverse iodine transfer polymerizations (RITP) of 2‐h‐ydroxyethyl acrylate (HEA) were performed in N,N‐dimethylformamide at 75°C using AIBN as initiator. Poly(2‐hydroxyethyl acrylate) (PHEA) with M_n = 3300 g mol^?1 and M_w/M_n <1.5 were obtained. Homopolymerization of styrene in RITP was also carried out under similar conditions using toluene as solvent. The resulting iodo‐polystyrene (PS‐I) with (M_{n, SEC} = 607 g mol^?1, polydispersity index (PDI) = 1.31) was used as a macroinitiator for the synthesis of amphiphilic block copolymers based on HEA with controlled well‐defined structure. Poly(styrene‐b‐2‐hydroxyethyl acrylate) (PS‐b‐PHEA) with M_n = 13,000 g mol^?1 and polydispersity index (M_w/M_n) = 1.4 was obtained, copolymer composition was characterized using ¹H‐NMR and FTIR, whereas SEC and gradient HPLC were used to confirm the formation of block copolymer and the living character of polymer chains. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Preparation and physicochemical performances of poly[(vinylidene fluoride)‐co‐hexafluoropropylene]‐based composite polymer electrolytes doped with modified carbon nanotubes

Modified carbon nanotubes (m‐CNTs) were successfully prepared by the interactions between nitric and sulfuric acids and CNTs, which was confirmed using Fourier transform infrared spectroscopy. Poly[(vinylidene fluoride)‐co‐hexafluoropropylene]‐based composite polymer electrolyte (CPE) membranes doped with various amounts of m‐CNTs were prepared by phase inversion method. The desired CPEs were obtained by soaking the liquid electrolytes for 30 min. The physicochemical and electrochemical properties of the CPE membranes were investigated using scanning electron microscopy, X‐ray diffraction, thermogravimetry, electrochemical impedance spectroscopy and linear sweep voltammetry. The results show that the CPE membranes doped with 2.2 wt% m‐CNTs possess the smoothest surface and the highest decomposition temperature about 450 °C. Obviously, adding an appropriate amount of m‐CNTs into the polymer matrix can decrease the crystallinity and enhance the ionic conductivity; the temperature dependence of ionic conductivity follows the Arrhenius relation and the ionic conductivity at room temperature is up to 4.9 mS cm^?1. The interfacial resistance can reach a stable value of about 415 Ω cm^?2 after 10 days storage. The excellent rate and cycle performances with an electrochemical working window up to 5.4 V ensure that the CPEs doped with 2.2 wt% m‐CNTs can be considered as potential candidates as polymer electrolyte for lithium ion batteries. © 2013 Society of Chemical Industry     

Facile fabrication of highly flexible poly(lactic acid) film using alternate multilayers of poly[(butylene adipate)‐co‐terephthalate]

Poly(lactic acid) (PLA) and poly[(butylene adipate)‐co‐terephthalate] (PBAT) are both commonly used biodegradable polymers. In this study, co‐extrusion of PLA and PBAT was used to create alternately multilayered films in order to obtain high‐flexibility PLA film. The incorporation of PBAT provides enhanced flexibility to PLA and the effect is more distinct in the PLA/PBAT multilayer film as the number of layers increases. Through differential scanning calorimetric and wide‐angle X‐ray scattering analyses, the crystallinity of PLA is shown to decrease more in the multilayer film than in the blended film. Transparency is also enhanced in the multilayer film. The fabrication of alternate multilayered film by co‐extrusion of PLA and PBAT shows a new method of preparing a flexible, transparent and fully biodegradable film, which is impossible through a blending process. © 2014 Society of Chemical Industry     

Preparation of monodispersed ZrO2 nanoparticles and their applications in poly[(vinylidene fluoride)‐co‐hexafluoropropylene]‐based composite polymer electrolytes

To improve the electrochemical performance of pure poly[(vinylidene fluoride)‐co‐hexafluoropropylene] (P(VDF‐HFP))‐based gel polymer electrolytes, different amounts of monodispersed ZrO₂ nanoparticles were introduced to fabricate P(VDF‐HFP)/ZrO₂ composite polymer electrolytes (CPEs) using the phase inversion method and activated processes, in which the monodispersed ZrO₂ nanoparticles were synthesized by an easy route without any chelating agents or surfactants, and confirmed using scanning electron microscopy, particle size distribution measurement and X‐ray diffraction. The characterization results show that the as‐fabricated CPE membranes present not only an abundant porous structure, but also an improved mechanical strength. In particular, sample CPE‐5 presents the best properties when the doped content of the monodispersed ZrO₂ nanoparticles reaches 5 wt% in the polymer matrix, in which the liquid uptake and ionic conductivity at room temperature are about 192.4% and 3.926 mS cm^?1, and the electrochemical working window and thermal decomposition temperature can increase to 5.1 V and 420 °C, respectively. Moreover, an assembled LiCoO₂/CPE‐5/Li coin cell can deliver excellent rate and cycling performance, in which the discharge specific capacity of the cell can show about 83.95% capacity retention at 2.0 C after 85 cycles. © 2018 Society of Chemical Industry     

Dielectric relaxation spectroscopy of poly[(R)‐3‐hydroxybutyrate] (PHB) during crystallization

The dielectric response of poly [(R)‐3‐hydroxybutyrate] (PHB) was investigated as a function of time after quenching a film from the melt to a crystallization temperature of 20 °C. In the frequency range investigated (20 to 10⁶ Hz) a relaxation maximum was observed–attributable to the glass transition–which could be analysed by the Havriliak–Negami relation. Changes in the complex dielectric constant were monitored both during spherulite growth (primary crystallization) and subsequently during a period of progressive crystallization (secondary crystallization) at room temperature. The relaxation strength changed only slightly during primary crystallization and its peak position remained at a constant frequency. Subsequently a continuous decrease in relaxation strength occurred, indicating considerable changes in molecular mobility after spherulite growth had been completed. The results provide further evidence that molecular mobility in the amorphous regions decreases significantly with time, and that this would be the reason why PHB shows embrittlement on ageing at room temperature. Copyright © 2004 Society of Chemical Industry     

Effects of plasma treatment on biocompatibility of poly[(L‐lactide)‐co‐(ϵ‐caprolactone)] and poly[(L‐lactide)‐co‐glycolide] electrospun nanofibrous membranes

Poly[(l ‐lactide)‐co ‐(? ‐caprolactone)] (PLCL) and poly[(l ‐lactide)‐co ‐glycolide] (PLGA) copolymers are widely used in neural guide tissue regeneration. In this research, the surface modification of their hydrophilicity was achieved using plasma treatment. Attachment and proliferation of olfactory ensheathing cells on treated electrospun membranes increased by 26 and 32%, respectively, compared to the untreated PLCL and PLGA counterparts. Cells cultivated on both the PLCL and PLGA membranes showed high viability (>95%) and healthy morphologies with no evidence of cytotoxic effects. Cells grown on treated electrospun fibres displayed significant increases in mitochondrial activity and reductions in membrane leakage when compared to untreated samples. The results suggested that plasma treatment of the surface of the polymers enhanced both cell viability and growth without incurring any cytotoxic effects. © 2017 Society of Chemical Industry     

Swelling and diffusion characteristics of novel semi‐interpenetrating network hydrogels composed of poly[(acrylamide)‐ co‐(sodium acrylate)] and poly[(vinylsulfonic acid), sodium salt]

A series of novel semi‐interpenetrating polymer networks (IPNs) composed of poly[(acrylamide)‐co‐(sodium acrylate)] with varying amounts (5, 10, and 15 wt%) of poly[(vinylsulfonic acid), sodium salt] was synthesized. The semi‐IPN hydrogels were characterized by infrared spectroscopy. The swelling behavior of these IPNs was studied in distilled water/physiological solutions/buffer solutions/salt solutions. As the amount of poly[(vinylsulfonic acid), sodium salt] increased in the network, the swelling capacity of the semi‐IPNs increased considerably. The swelling and diffusion characteristics such as water penetration velocity (v), diffusion exponent (n), and diffusion coefficient (D) were calculated in distilled water, as well as in other physiological solutions. The highest swelling capacity was noted in urea and glucose solutions. The semi‐IPN hydrogels followed non‐Fickian diffusion behavior in water and physiological fluids, whereas Fickian behavior was observed in buffer solutions. The stimuli‐responsive characteristics towards physiological fluids, salt concentration, and temperature of these semi‐IPN hydrogels were also investigated. The swelling behavior of the semi‐IPNs decreased markedly with an increase of the concentration of the salt solutions. Copyright © 2006 Society of Chemical Industry     

Invertase immobilized on spacer‐arm attached poly(hydroxyethyl methacrylate) membrane: Preparation and properties

Microporous poly(2‐hydroxyethyl methacrylate) (pHEMA) membrane was prepared by UV‐initiated photopolymerization. The spacer arm (i.e., hexamethylene diamine) was attached covalently and then invertase was immobilized by the condensation reaction of the amino groups of the spacer arm with carboxyl groups of the enzyme in the presence of carbodiimides. The values of the Michael's constant K_m of invertase were significantly larger (ca. 2.5 times) upon immobilization, indicating decreased affinity by the enzyme for its substrate, whereas V_max was smaller for the immobilized invertase. Immobilization improved the pH stability of the enzyme as well as its temperature stability. Thermal stability was found to increase with immobilization and at 70°C the half times for the activity decay were 12 min for the free enzyme and 41 min for the immobilized enzyme. The immobilized enzyme activity was found to be quite stable in repeated experiments. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 75: 1685–1692, 2000     

Synthesis,characterization, conductivity,band gap,and kinetic of thermal degradation of poly‐4‐[(2‐mercaptophenyl) imino methyl] phenol

The oxidative polycondensation reaction conditions of 4‐[(2‐mercaptophenyl) imino methyl] phenol (2‐MPIMP) were studied in an aqueous acidic medium between 40 and 90°C by using oxidants such as air, H₂O₂, and NaOCl. The structures of the synthesized monomer and polymer were confirmed by FTIR, ¹H NMR, ¹³C NMR, and elemental analysis. The characterization was made by TGA‐DTA, size exclusion chromatography (SEC) and solubility tests. At the optimum reaction conditions, the yield of poly‐4‐[(2‐mercaptophenyl) imino methyl]phenol (P‐2‐MPIMP) was found to be 92% for NaOCl oxidant, 84% for H₂O₂ oxidant 54% for air oxidant. According to the SEC analysis, the number‐average molecular weight (M_n), weight‐average molecular weight (M_w), and polydispersity index values of P‐2‐MPIMP were found to be 1700 g mol^?1, 1900 g mol^?1, and 1.118, using H₂O₂; 3100 g mol^?1, 3400 g mol^?1, and 1.097, using air; and 6750 g mol^?1, 6900 g mol^?1, and 1.022, using NaOCl, respectively. According to TG analysis, the weight losses of 2‐MPIMP and P‐2‐MPIMP were found to be 95.93% and 76.41% at 1000°C, respectively. P‐2‐MPIMP showed higher stability against thermal decomposition. Also, electrical conductivity of the P‐2‐MPIMP was measured, showing that the polymer is a typical semiconductor. The highest occupied molecular orbital, the lowest unoccupied molecular orbital, and the electrochemical energy gaps (E′_g) of 2‐MPIMP and P‐2‐MPIMP were found to be ?6.13, ?6.09; ?2.65, ?2.67; and 3.48, 3.42 eV, respectively. Kinetic and thermodynamic parameters of these compounds investigated by MacCallum‐Tanner and van Krevelen methods. The values of the apparent activation energies of thermal decomposition (E_a), the reaction order (n), pre‐exponential factor (A), the entropy change (ΔS*), enthalpy change (ΔH*), and free energy change (ΔG*) were calculated from the TGA curves of compounds. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Synthesis and in vitro degradation properties of poly[(tetramethylene carbonate)‐co‐(sebacic anhydride)]

A novel poly[(tetramethylene carbonate)‐co‐(sebacic anhydride)] (PTCSA) was synthesized by the melt polycondensation reaction of sebacic acid (SA) and the dicarboxylic acid which derived from oligo(tetramethylene carbonate) diol via the corresponding mixed anhydrides. The copolymer structure was confirmed by means of FTIR and [¹H] NMR spectra. DSC analysis showed PTCSA was semicrystalline polymer which had low T_g (<?30 °C). The measurements of contact angles indicated that the hydrophobicity of PTCSA increased as the content of carbonate segments increased. In vitro degradation of PTCSA was performed in lipase‐free and lipase‐containing phosphate‐buffer saline (0.1 M, pH 7.4) at 37 °C. It was found that the degradation rate of PTCSA increased with the amount of SA. After 7 days of degradation in lipase‐free phosphate‐buffer saline, the weight loss of PTCSA was 74, 49 and 22% for 80, 58 and 32 mol% SA contained samples, respectively. The weight loss of PTCSA increased rapidly in the first week, then slowed down but could be greatly enhanced by lipase. After 3 weeks of degradation with or without lipase, the weight loss of PTCSA was 66 and 52% for 58 mol% SA‐containing samples, respectively. The size of the samples was gradually reduced and the surface became coarse. It was also found that the molecular weights of the outer layer were lower than those of the inner layer of the samples after degradation. The results suggested that PTCSA was some kind of biodegradation and surface‐erosion material. © 2001 Society of Chemical Industry     

Synthesis and characterization of multi‐block copolymers containing poly [(3‐hydroxybutyrate)‐co‐(3‐hydroxyvalerate)] and poly(ethylene glycol)

Various problems, including high crystallinity, high melting temperature, poor thermal stability, hydrophobicity and brittleness, have impeded many practical applications of poly[(3‐hydroxybutyrate)‐co‐(3‐hydroxyvalerate)] (PHBV) as an environmentally friendly material and biomedical material. In the work reported here, multi‐block copolymers containing PHBV and poly(ethylene glycol) (PHBV‐b‐PEG) were synthesized with telechelic hydroxylated PHBV as a hard and hydrophobic segment, PEG as a soft and hydrophilic segment and 1,6‐hexamethylene diisocyanate as a coupling reagent to solve the problems mentioned above. PHBV and PEG blocks in PHBV‐b‐PEG formed separate crystalline phases with lower crystallinity levels and lower melting temperatures than those of phases formed in the precursors. The crystallite dimensions of the two blocks in PHBV‐b‐PEG were smaller than those of the corresponding precursors. Compared to values for the original PHBV, the maximum decomposition temperature of the PHBV block in PHBV‐b‐PEG was 16.0 °C higher and the water contact angle was 9° lower. In addition, the elongation at break was 2.8% for a pure PHBV fiber but 20.9% for a PHBV/PHBV‐b‐PEG fiber with a PHBV‐b‐PEG content of 30%. PHBV‐b‐PEGs can overcome some of the disadvantages of pure PHBV; it is possible that PHBV might be a good candidate for the formulation of environmentally friendly materials and biomedical materials. Copyright © 2010 Society of Chemical Industry     

Anomalous rheological behavior of poly(1‐vinyl‐2‐pyrrolidone) and CuCl2 in solution and their interactions in solid composites

BACKGROUND: The aggregation structure of polymers in solution is an important aspect of their behavior. The interactions between metal ions and water‐soluble polymers have a significant influence on the conformation behavior of biological macromolecules, and on the ionic selectivity of cells, etc. RESULTS: The rheological behavior of poly(1‐vinyl‐2‐pyrrolidone) (PVP) and CuCl₂ dispersed in N,N‐dimethylformamide was investigated using rheological techniques. Concentrated solutions containing CuCl₂ exhibited a rheological behavior different from those containing other metal chlorides (LiCl, CaCl₂ and CoCl₂). This indicated that the variation in the aggregation state of the PVP chains with concentration of CuCl₂ was different from those of PVP solutions containing Li⁺, Ca²⁺ or Co²⁺ ions. CONCLUSION: The interactions between PVP and CuCl₂ inhibit the crystallization of CuCl₂ and induce the formation of microphase separation in the system. Copyright © 2009 Society of Chemical Industry     

Preparation of collagen‐immobilized poly(ethylene glycol)/poly(2‐hydroxyethyl methacrylate) interpenetrating network hydrogels for potential application of artificial cornea

To enhance the mechanical strength of poly(ethylene glycol)(PEG) gels and to provide functional groups for surface modification, we prepared interpenetrating (IPN) hydrogels by incorporating poly(2‐hydroxyethyl methacrylate)(PHEMA) inside PEG hydrogels. Formation of IPN hydrogels was confirmed by measuring the weight percent gain of the hydrogels after incorporation of PHEMA, as well as by ATR/FTIR analysis. Synthesis of IPN hydrogels with a high PHEMA content resulted in optically transparent and extensively crosslinked hydrogels with a lower water content and a 6 ～ 8‐fold improvement in mechanical properties than PEG hydrogels. Incorporation of less than 90 wt % PHEMA resulted in opaque hydrogels due to phase separation between water and PHEMA. To overcome the poor cell adhesion properties of the IPN hydrogels, collagen was covalently grafted to the surface of IPN hydrogels via carbamate linkages to hydroxyl groups in PHEMA. Resultant IPN hydrogels were proven to be noncytotoxic and cell adhesion study revealed that collagen immobilization resulted in a significant improvement of cell adhesion and spreading on the IPN hydrogel surfaces. The resultant IPN hydrogels were noncytotoxic, and a cell adhesion study revealed that collagen immobilization improved cell adhesion and spreading on the IPN hydrogel surfaces significantly. These results indicate that PEG/PHEMA IPN hydrogels are highly promising biomaterials that can be used in artificial corneas and a variety of other load‐bearing tissue engineering applications. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011