Kinetics of the reaction of iron blast furance slag/hydrated lime sorbents with SO2 at low temperatures: effects of sorbent preparation conditions

Sorbents highly reactive towards SO₂ have been prepared from iron blast furnace slag and hydrated lime under different hydration conditions. The reaction of the dry sorbents with SO₂ has been studied under the conditions similar to those in the bag filters in the spray-drying flue gas desulfurization system. The reaction was well described by a modified surface coverage model which assumes the reaction rate being controlled by chemical reaction on sorbent grain surface and takes into account the effect of sorbent Ca molar content and the surface coverage by product. The effects of sorbent preparation conditions on sorbent reactivity were entirely represented by the effects of the initial specific surface area (S_g0) and the Ca molar content (M⁻¹) of sorbent. The initial conversion rate of sorbent increased linearly with increasing S_g0, and the ultimate conversion increased linearly with increasing S_g0M⁻¹. The initial conversion rate and ultimate conversion of sorbent increased significantly with increasing relative humidity of the gas. Temperature and SO₂ concentration had mild effects on the initial conversion rate and negligible effects on the ultimate conversion.     

Thermogravimetric analysis of polyurethane–polysulfone blends

Thermal decomposition of blends of a poly(ester urethane) and poly(ether sulfone) with or without poly(urethane sulfone), taken as a compatibilizing agent, was studied by thermogravimetric analysis under dynamic conditions. Theoretical mass loss curves were compared with experimental ones and it was found that the blends studied possessed lower thermal stability than the pure polymers, indicating the presence of interactions in the degradation process. The shifts between the theoretical and experimental curves became smaller as the amounts of polysulfone increased, confirming the thermal stabilisation effect of this polymer. The analysis of activation energy revealed, for both binary and ternary systems, that E_CR (T_max corresponding to the main decomposition stage of polysulfone) increased as the amount of this polymer increased and also the reaction order became zero. For the polyurethane decomposition stages and blending revealed no significant changes as far as activation energy and order of reaction were concerned. © 2002 Society of Chemical Industry     

Thermogravimetric characteristics of aerobic granules developed at different salinities

BACKGROUND: Aerobic granular sludge is a self‐immobilization biotechnology for wastewater treatment. The thermogravimetric characteristics of aerobic granules were investigated in this study. RESULTS: The strongly physically bound water in granules that developed at a salinity of 1% (in reactor R1) and 5% (in reactor R2) were 5% and 3%, respectively. In addition, the extracellular polymer substances (EPS) affected the bound water more significantly at a low salinity than a higher one. Based on thermogravimetric analysis (TGA), granules that developed at low salinity (such as 1% in R1) exhibited a rich diversity of organic components, and higher total EPS concentrations, inferred from the ratios of volatile solids to total solids. Additionally, the maximum weight loss rates of the granules in all reactors occurred at a temperature of around 250 °C and the endothermic peaks shifted to a relatively low temperature with increasing salinity regardless of the existence of EPS. CONCLUSION: Increasing the salinity in the substrates slightly decreased the bound water fraction in granules and reduced the richness of the granule components as well as the biodiversity. This study provides detailed information on the components of aerobic granule. Copyright © 2007 Society of Chemical Industry     

Fire‐retardant copolymer of acrylonitrile with O,O‐diethyl‐O‐allyl thiophosphate

A novel halogen‐free flame retardant, O,O‐diethyl‐O‐allyl thiophosphate (DATP), which simultaneously contained phosphorus and sulfur, was synthesized through a simple method. The structure of DATP was characterized by Fourier transform infrared spectroscopy, ¹H‐NMR, and mass spectroscopy. The flame‐retardant copolymer was obtained by the free‐radical copolymerization of DATP with acrylonitrile. The flammability and thermal degradation characteristics of the copolymer were assayed by limiting oxygen index measurement, thermogravimetric analysis, and differential scanning calorimetry. The results show that the incorporation of a small percentage of DATP into the copolymer had a significant effect on the retarding combustion of the copolymer, with the limiting oxygen index of the copolymer reaching 28.5% and the char yield being 68.63 wt % at 554°C. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Thermal decomposition behavior of carbon‐nanotube‐reinforced poly(ethylene 2,6‐naphthalate) nanocomposites

Polymer nanocomposites based on poly (ethylene 2,6‐naphthalate) (PEN) and carbon nanotubes (CNTs) were prepared by direct melt blending with a twin‐screw extruder. Dynamic thermogravimetric analysis was conducted on the PEN/CNT nanocomposites to clarify the effect of CNTs on the thermal decomposition behavior of the polymer nanocomposites. The thermal decomposition kinetics of the PEN/CNT nanocomposites was strongly dependent on the CNT content, the heating rate, and the gas atmosphere. On the basis of the thermal decomposition kinetic analysis, the variation of the activation energy for thermal decomposition revealed that a very small quantity of CNTs substantially improved the thermal stability and thermal decomposition of the PEN/CNT nanocomposites. Morphological observations demonstrated the formation of interconnected or network‐like structures of CNTs in the PEN matrix. The unique character of the CNTs introduced into the PEN matrix, such as the physical barrier effect of CNTs during thermal decomposition and the formation of interconnected or network‐like structures of CNTs, resulted in the enhancement of the thermal stability of the PEN/CNT nanocomposites. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Direct polycondensation of N‐trimellitylimido‐L‐isoleucine with aromatic diamines

N‐Trimellitylimido‐L ‐isoleucine (3) was prepared from the reaction of trimellitic anhydride with L ‐isoleucine [L ‐2‐amino‐3‐methylvalerianic acid or (2S,3S)‐2‐amino‐3‐methyl‐n‐valerinic acid] in an N,N‐dimethylformamide solution at the refluxing temperature. The direct polycondensation reaction of the monomer imide diacid (3) with 1,4‐phenylenediamine, 4,4′‐diaminodiphenylmethane, 4,4′‐diaminodiphenylsulfone, diaminodiphenylether, 1,5‐naphthalendiamine, 2,4‐diaminotoluene, and 1,3‐phenylenediamine was performed in a medium consisting of triphenyl phosphite, N‐methyl‐2‐pyrolidone (NMP), pyridine, and calcium chloride. The polycondensation was performed under two different conditions: in one method, the reaction mixture was heated in an NMP solution at 60, 90, and then 130°C for different periods of time, and in the other method, the reaction mixture was refluxed only for 1 min in the same solvent. The resulting poly(amide imide)s (PAIs), with inherent viscosities of 0.21–0.37 dL/g, were obtained in high yields. All of these compounds were fully characterized by IR spectra, elemental analyses, and specific rotation measurements. Some structural characterizations and physical properties of these new optically active PAIs were examined. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 116–122, 2003     

脉冲电晕结合Ca(OH)2吸收法脱硫脱硝

Removal of SO2 and NOx by pulsed corona combined with in situ alkali absorption was experimentally investigated.In the reactor,a plate-wire-plate combination is devised for generating pulsed corona and then alkaline absorbent slurries were introduced into the reactor by a continuous band conveying system to capture the gaseous reaction products.It was found that both SO2 and NO could be removed by corona combined with in situ alkali absorption.The removal of SO2 increased to 75%with the corona discharge,compared with 60%removal only with Ca(OH)2 absorption.About 40%removal of NO was reached by pulsed corona combined with in situ Ca(OH)2 absorption.It was found that SO2 and NO in the gas stream are oxidized to SO3 and NO2 by pulsed corona respectively,and then absorbed by the alkali in the reactor.The removals of SO2 as well as NO were higher with Ca(OH)2 as the absorbent,compared with using CaCO3 or ZnO.     

Photopolymerization and thermal behavior of phosphate diacrylate and triacrylate used as reactive‐type flame‐retardant monomers in ultraviolet‐curable resins

Tri(acryloyloxyethyl)phosphate (TAEP) and di(acryloyloxyethyl)ethyl phosphate (DAEEP) were used as reactive‐type flame‐retardant monomers along with commercial epoxy acrylate and polyurethane acrylate oligomers in ultraviolet (UV)‐curable resins. The concentrations of the monomers were varied from 17 to 50 wt %. The addition of the monomers greatly reduced the viscosity of the oligomers and increased the photopolymerization rates of the resins. The flame retardancy and thermal degradation behavior of the UV‐cured films were investigated with the limiting oxygen index (LOI) and thermogravimetric analysis. The results showed that the thermal stability at high temperatures greater than 400°C and the LOI values of the UV‐cured resins, especially those containing epoxy acrylate, were largely improved by the addition of the monomers. The dynamic mechanical thermal properties of the UV‐cured films were also measured. The results showed that the crosslink density increased along with the concentrations of the monomers. However, the glass‐transition temperature decreased with an increasing concentration of DAEEP because of the reduction in the rigidity of the cured films, whereas the glass‐transition temperature increased with the concentration of TAEP because of the higher crosslink density of the cured films. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 185–194, 2005     

Thermal degradation of poly(dimethylsilylene) and poly(tetramethyldisilylene‐co‐styrene)

Thermal degradation of poly(dimethylsilylene) homopolymer (PDMS) and poly(tetramethyldisilylene‐co‐styrene) copolymer (PTMDSS) was investigated by pyrolysis‐gas chromatography and thermogravimetry (TG). PDMS decomposes by depolymerization, producing linear and cyclic oligomeric products, whereas PTMDSS decomposes by random degradation along the chain resulting in each monomeric product and various other combination products. The homopolymer was found to be much less stable than the copolymer. The decomposition mechanisms leading to the formation of various products are shown. The kinetic parameters of thermal degradation were evaluated by different integral methods using TG data. The activation energies of decomposition (E) for the homopolymer and the copolymer are found to be 122 and 181 kJ/mol, respectively, and the corresponding values of order of reaction are 1 and 1.5. The observed difference in the thermal stability and the values of the kinetic parameters for decomposition of these polymers are explained in relation with the mechanism of decomposition. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci, 2006     

Effect of BaTiO3 on the microwave absorbing properties of Co‐doped Ni‐Zn ferrite nanocomposites

Coprecipitation and hydrothermal method were utilized for the synthesis of Co‐doped Ni‐Zn ferrite and barium titanate nanoparticles. The microwave absorption properties of Co‐doped Ni‐Zn ferrite/barium titanate nanocomposites with single layer structure were studied in the frequency range of 8.2–12.4 GHz.The spectroscopic characterizations of the nanocomposites were examined using X‐ ray diffraction, scanning electron microscopy, transmission electron microscopy and dynamic light scattering measurement. Thermogravimetric analysis indicated the high thermal stabilities of the composites. The composite materials showed brilliant microwave absorbing properties in a wide range of frequency in the X‐band region with the minimum return loss of ?42.53 dB at 11.81 GHz when sample thickness was 2 mm and the mechanisms of microwave absorption are happening mainly due to the dielectric loss. Compared with pure Co‐doped Ni‐Zn ferrite, Co‐doped Ni‐Zn ferrite/BaTiO₃ composites exhibited enhanced absorbing properties. The microwave absorbing properties can be modulated by controlling the BaTiO₃ content of the absorbers and also by changing the sample thicknesses. Therefore, these composites can be used as lightweight and highly effective microwave absorbers. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39926.     

Phenol–formaldehyde‐type resins made from phenol‐liquefied wood for the bonding of particleboard

Liquefaction of southern pine wood in phenol in 30–40 : 70–60 weight ratios resulted in homogeneous liquefied materials, which were directly used to synthesize phenol–formaldehyde (PF)‐type resins. The synthesized resins showed good physical and handling properties: low viscosity, stability for storage and transportation, and resin applicable by a common sprayer. Particleboard panels bonded with the synthesized resins showed promising physical properties and significantly lower formaldehyde emission values than those bonded with the urea–formaldehyde resin control. One deficiency observed for the synthesized resins was lower internal bond values, which might be overcome the use of a hot‐stacking procedure. Overall, the process of wood liquefaction with limited amounts of phenol as a solvent was shown to have the potential of providing practical, low‐cost PF‐type resins with very low formaldehyde emission potentials. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Fabrication of reverse‐osmosis membranes for the desalination of underground water via the γ‐radiation grafting of acrylic acid onto polyethylene films

Research has been devoted to the desalination of saline water to fresh water suitable for human demands because of the shortage of water in some countries. Therefore, in this study, reverse‐osmosis membranes were prepared via the γ‐radiation graft copolymerization of acrylic acid onto high‐density and low‐density polyethylene. The factors that could affect the grafting process, such as the solvent type, monomer and inhibitor concentration, and irradiation dose, were investigated to determine the optimum conditions for radiation grafting. The polyethylene grafted acrylic acid copolymers (PAAc‐g‐PE) graft copolymer was characterized by Fourier transform infrared spectroscopy, scanning electron microscopy, and mechanical, rheological, and thermal property testing to illustrate the possibility of practical use in water desalination. The prepared grafted membranes showed significant results in the reverse‐osmosis desalination method with underground saline water. The factors affecting the desalination of water, such as the water flux, operation time, and grafting percentage, were studied. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45410.     

Thermal degradation kinetics of poly(N‐adamantyl‐exo‐nadimide) synthesized by addition polymerization

The thermal decomposition behavior and degradation kinetics of poly(N‐adamantyl‐exo‐nadimide) were investigated with thermogravimetric analysis under dynamic conditions at five different heating rates: 10, 15, 20, 25, and 30°C/min. The derivative thermogravimetry curves of poly(N‐adamantyl‐exo‐nadimide) showed that its thermal degradation process had one weight‐loss step. The apparent activation energy of poly(N‐adamantyl‐exo‐nadimide) was estimated to be about 214.4 kJ/mol with the Ozawa–Flynn–Wall method. The most likely decomposition process was an F1 deceleration type in terms of the Coats–Redfern and Phadnis–Deshpande results. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 3003–3009, 2007     

Thermogravimetric analysis of blends of low‐density polyethylene and poly(dimethyl siloxane) rubber: The effects of compatibilizers

The thermal stability of vulcanizates of low‐density polyethylene (LDPE), poly(dimethyl siloxane) (PDMS) rubber, and their blends was studied by nonisothermal thermogravimetry. Four ethylene copolymers [ethylene methyl acrylate (EMA), ethylene vinyl acetate, ethylene acrylic acid, and a zinc‐salt‐based ionomer (Lotek 4200)] were used as compatibilizers for the blend systems. The thermograms and derivatograms of the blends showed that thermal degradation took place in two stages, whereas those for the base polymers showed single‐stage degradation. Kinetic studies of the blends and pure components showed that the degradation followed first‐order reaction kinetics. The activation energy at 10% degradation was determined with the Freeman–Carroll method and was at a maximum (42.34 kcal/mol) for the 25:75 LDPE/PDMS rubber blend. The half‐life at 200°C was evaluated by the Flynn–Wall method and was at a maximum (812.5 days) for the same blend. Out of four compatibilizers, EMA showed the maximum activation energy (34.25 kcal/mol) for degradation and a maximum half‐life (695.3 days), indicating that EMA was the best compatibilizer for the blend system. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 635–642, 2003     

Fluidization Behavior of Cohesive Ca(OH)2 Powders Mixed with Hydrophobic Silica Nanoparticles

Dry mixing with hydrophobic silica nanopowders was used to improve the fluidization quality of Ca(OH)₂ particles which belong to the Geldart C group and, thus, normally cannot be fluidized. Three parameters, i.e., sieved size of Ca(OH)₂ particles and sieved size and weight percentage of SiO₂ nanoparticles were selected for experiments. A direct proportionality was found between the coverage quality of materials over each other and the fluidization behavior of their corresponding adsorbents. Optimum SiO₂ size and concentration values were determined for the improvement of Ca(OH)₂ fluidizability. The sieved size of Ca(OH)₂ powder had no consequential effect on the coverage quality. The Richarson‐Zaki equation and fractal analysis combined with a modified Richardson‐Zaki approach were proposed for prediction of the fluidization quality and agglomerate size.     

基于中温烟气多污染物控制的烟气脱硫实验

中温（200～400℃）烟气多污染物一体化脱除方法能够实现烟尘、NO_x、SO₂一体化脱除,在当前环境问题日趋严峻的背景下具有一定的发展前景。氢氧化钙作为该方法的一种潜力脱硫剂,在中温条件下进行烟气中SO₂脱除的实验研究较少,针对该情况,在自制实验系统上探究了不同因素对SO₂脱除效果的影响,研究表明,在实验室自制的固定床实验系统下,烟气成分中水蒸气、CO₂、NO_x、O₂等的存在会对脱硫产生抑制,升高温度对SO₂脱除有一定促进作用。对吸附产物进行了XRD、SEM等表征,验证了化学吸附机理,氢氧化钙在该温度区间会逐渐分解形成氧化钙,促进SO₂的吸附与内扩散,使得脱硫效果提高。研究结果为进一步提高脱硫效果,提高氢氧化钙活性,并为下一步实现中温下烟气多污染物一体化脱除奠定基础。