Recovery of value‐added globular proteins from tannery wastewaters using PEG – salt aqueous two‐phase systems

Leather processing involves discharge of high‐value soluble globular proteins in the wastewater. The recovery of value‐added products from the wastewaters is gaining more importance in the context of recovery of wealth from waste. The recovery of these globular proteins from tannery wastewater was selected as a practical model system to study the implementation of polyethylene glycol (PEG)‐sulfate aqueous two‐phase systems (ATPS). The partition coefficient of bovine serum albumin is comparable to that of soluble proteins from tannery wastewaters. The influence of concentration of polymer, salt, pH and temperature on the partitioning of soluble proteins from tannery wastewaters has been studied. The PEG6000 + sodium sulfate + water system provide better partitioning of these soluble proteins as compared to PEG6000 + ammonium sulfate system. The maximum protein recovery yield for PEG6000 + sodium sulfate + water system at 20 °C is 92.75%. The influence of temperature indicates the recovery of proteins from tannery wastewater to be better at lower temperature. The findings of these studies raise the potential application of ATPS processes for protein recovery from complex biological systems. Copyright © 2006 Society of Chemical Industry     

Recovery of B19 virus-like particles by aqueous two-phase systems

The development of process routes for the recovery of intracellular B19 virus-like particles by aqueous two-phase systems (ATPS) was investigated in this study. Two processes have been developed which may prove advantageous when compared to the conventional recovery processes. One process was designed to recover B19 particles from the bottom phase of a polyethylene glycol (PEG) 1000-magnesium sulphate system while removing cell debris and 31% of total protein with the top phase, interface and sediment. With regard to the analysis of VP1 and VP2 capsid protein after extraction, the yield of B19 particles in the bottom phase was 92.8% or 85.7%, respectively. In an alternative process, B19 particles were recovered from a clarified cell disruptate by interfacial partition. With regard to VP1 and VP2 proteins, 95.3% or 33.2%, respectively was recovered in the interface of a PEG 1000-magnesium sulphate system.     

Practical application of aqueous two‐phase systems for the development of a prototype process for c‐phycocyanin recovery from Spirulina maxima

A novel process for the recovery of c‐phycocyanin from Spirulina maxima exploiting aqueous two‐phase systems (ATPS), ultrafiltration and precipitation was developed in order to reduce the number of unit operations and benefit from an increased yield of the protein product. The evaluation of system parameters such as PEG molecular mass, concentration of PEG as well as salt, system pH and volume ratio was carried out to determine under which conditions the c‐phycocyanin and contaminants concentrate to opposite phases. PEG1450–phosphate ATPS proved to be suitable for the recovery of c‐phycocyanin because the target protein concentrated in the top phase whilst the cell debris concentrated in the bottom phase. A two‐stage ATPS process with a phase volume ratio (V_r) equal to 0.3, PEG1450 7% (w/w), phosphate 20% (w/w) and system pH of 6.5 allowed c‐phycocyanin recovery with a purity of 2.4 (estimated as the relationship of the 620 nm to 280 nm absorbances). The use of ultrafiltration (with a 30 kDa membrane cut‐off) and precipitation (with ammonium sulfate) resulted in a recovery process that produced a protein purity of 3.8 ± 0.1 and an overall product yield of 29.5% (w/w). The results reported here demonstrated the practical implementation of ATPS for the design of a prototype recovery process as a first step for the commercial purification of c‐phycocyanin produced by Spirulina maxima. © 2001 Society of Chemical Industry     

Partitioning behaviour of cephalexin and 7‐aminodeacetoxicephalosporanic acid in PEG/ammonium sulfate aqueous two‐phase systems

In order to develop an aqueous two‐phase system (ATPS) for cephalexin synthesis with extractive bioconversion, the partitioning behaviour of cephalexin and 7‐aminodeacetoxicephalosporanic acid (7‐ADCA) in poly(ethylene glycol) (PEG)/salt ATPS were examined. Parameters such as PEG size, salt type and tie line length were investigated to find a primary extraction system. In PEG400/ammonium sulfate and PEG400/magnesium sulfate systems, the partition coefficient of cephalexin (K_C) was larger than 1 while that of 7‐ADCA (K_A) deviated about 1.5. Addition of neutral salts, surfactants and water‐miscible solvents were also investigated in the primary ATPS in order to improve the separation efficiency. K_C greatly increased when neutral salts and surfactants were added to the PEG400/ammonium sulfate primary systems whereas K_A was only slightly higher than that of the additive‐free ATPS. In an improved ATPS for extractive bioconversion, consisting of PEG400 (20% w/w), ammonium sulfate (17.5% w/w), methanol (5% w/w) and NaCl (3% w/w), a K_C value of up to 15.2 was achieved; K_A was 1.8; K_P (partition coefficient of phenylglycine methyl ester) was 1.2 and the recovery yield of cephalexin was 94.2%. The results obtained from the extractive bioconversion of cephalexin in the improved ATPS showed that it is feasible to perform such an enzymatic process in an ATPS and the system offers the potential as a model for enzymatic synthesis of some water soluble products. © 2001 Society of Chemical Industry     

Aqueous two‐phase systems for the recovery of a recombinant viral coat protein from Escherichia coli

In this study the use of an aqueous two‐phase system (ATPS) following the direct chemical extraction of a recombinant viral coat protein, from the cytoplasm of Escherichia coli, is evaluated. The driving force is the need to establish an economically‐viable process for the manufacture of a vaccine against human papilloma infection. The partition behaviour of recombinant L1 protein, the major structural protein of the virus, and DNA was investigated in a polyethylene glycol (PEG)–phosphate system. An evaluation of system parameters including PEG molecular mass and the concentrations of PEG and phosphate was conducted, to estimate conditions under which the L1 protein and DNA partition to opposite phases. ATPS extraction comprising a volume ratio of 1.00, PEG 1000 (18.0%(w/w)) and phosphate (15.0%(w/w)) provided the conditions for accumulation of DNA into the bottom phase and concentration of L1 protein into the opposite phase (ie partition coefficient of DNA; ln K_DNA < 0.0 and partition coefficient of L1; ln K_L1 > 2.5). The findings reported here demonstrate the potential of ATPS to recover recombinant protein released from E coli by direct chemical extraction. © 2002 Society of Chemical Industry     

Improved recovery of B‐phycoerythrin produced by the red microalga Porphyridium cruentum

A simplified process for the primary recovery and purification of B‐phycoerythrin (BPE) from Porphyridium cruentum exploiting aqueous two‐phase systems (ATPS) and isoelectric precipitation was developed in order to reduce the number of unit operations and benefit from increased purity and yield of the protein product. Evaluation of the partitioning behaviour of BPE in polyethylene glycol (PEG)/sulphate, PEG/dextran and PEG/phosphate ATPS was carried out to determine under what conditions the BPE and contaminants concentrated into opposite phases. An additional stage of isoelectric precipitation at pH 4.0 after cell disruption resulted in an increase in purity of the target protein from the BPE crude extract and enhanced the performance of the subsequent ATPS. PEG1000/phosphate ATPS proved to be suitable after isoelectric precipitation for the recovery of highly purified (defined as absorbance ratio A_{545 nm}/A_{280 nm} > 4.0) BPE with a potential commercial value as high as US$ 50/mg. An ATPS extraction stage comprising 29.5% (w/w) PEG1000, 9.0% (w/w) phosphate, a volume ratio (V_r) equal to 1.0, a system pH of 7.0 and loaded with 40% (w/w) of the BPE extract generated by precipitation allowed BPE recovery with a purity of 4.1±0.2 and an overall product yield of 72% (w/w). The purity of BPE from the crude extract increased 5.9‐fold after isoelectric precipitation and ATPS. The results reported herein demonstrate the benefits of the practical application of isoelectric precipitation together with ATPS for the recovery and purification of BPE produced by P. cruentum as a first step in the development of a commercial purification process. Copyright © 2006 Society of Chemical Industry     

用聚乙二醇沉淀法清除细胞碎片

<文> 自 80年代以来,双水相苯取技术用于生化产品的分离受到重视,尤其对聚乙二醇 （PEG）和无机盐体系的开发研究更多“,“,双水相荤取技术在分离细胞匀浆中胞内产物和细胞 碎片方面,显示出可取代高速离心和微孔膜过滤的潜力。目前大多数研究集中在双水相革取的 机理和分离纯化不同蛋白质上,对清除细胞碎片的应用研究尚不多见。本文从细胞碎片在 PEG－无机盐系统的分配规律中发规系统未形成双水相前,存在一个液－固两相生成区。在此 区内大部分碎片形成固相沉淀,低速离心即可除去。以从酵母中提取醇脱氢酶为例,将这种新 的售脸碰计茉D体同Nil。t。十签人（门的W＊栅茉阶体淋杆了计林     

Potential application of aqueous two‐phase systems for the fractionation of RNase A and α‐Lactalbumin from their PEGylated conjugates

BACKGROUND: PEGylation reactions often result in a heterogeneous population of conjugated species and unmodified proteins that presents a protein separations challenge. Aqueous two‐phase systems (ATPS) are an attractive alternative for the potential fractionation of native proteins from their PEGylated conjugates. The present study characterizes the partition behaviors of native RNase A and α‐Lac and their mono and di‐PEGylated conjugates on polyethylene glycol (PEG)—potassium phosphate ATPS. RESULTS: A potential strategy to separate unreacted native protein from its PEGylated species was established based upon the partition behavior of the species. The effect of PEG molecular weight (400–8000 g mol^?1), tie‐line length (15–45% w/w) and volume ratio (V_R; 0.33, 1.00 and 3.00) on native and PEGylated proteins partition behavior was studied. The use of ATPS constructed with high PEG molecular weight (8000 g mol^?1), tie‐line lengths of 25 and 35% w/w, and V_R values of 1.0 and 3.0 allowed the selective fractionation of native RNase A and α‐Lactalbumin, respectively, from their PEGylated conjugates on opposite phases. Such conditions resulted in an RNase A bottom phase recovery of 99%, while 98% and 88% of mono and di‐PEGylated conjugates, respectively were recovered at the top phase. For its part, α‐Lac had a bottom phase recovery of 92% while its mono and di‐PEGylated conjugates were recovered at the top phase with yields of 77% and 76%, respectively. CONCLUSIONS: The results reported here demonstrate the potential application of ATPS for the fractionation of PEGylated conjugates from their unreacted precursors. Copyright © 2010 Society of Chemical Industry     

Partition of tannery wastewater proteins in aqueous two-phase poly (ethylene glycol)-magnesium sulfate systems: Effects of molecular weights and pH

The partitioning behavior of soluble proteins from tannery wastewater using aqueous two-phase system (ATPS) was investigated. An ATPS polyethylene glycol (PEG)/MgSO₄ was examined with regard to the effects of PEG molecular weight (MW) and concentration, MgSO₄ concentration, pH and NaCl concentration on protein partition and extraction. The partition coefficients measured for soluble proteins were proportional to the difference in PEG concentration between the phases. The MW and concentration of PEG were found to have significant effects on protein partition and extraction with low MW PEG4000 showing the best conditions for the partitioning of protein in PEG+MgSO₄+water system. Sulfate salt was chosen as the phase-forming salt because of its ability to promote hydrophobic difference between the phases. This system was operated at room temperature . Increase in pH of the system increases the partition coefficient of proteins from tannery wastewater. The addition of sodium chloride showed significant influence on the partition coefficient. ATPS comprising PEG4000-magnesium sulfate provided a means for the recovery of proteins from tannery wastewater. The maximum percentage yield of protein extracted is 82.68%.     

Separation and Purification of Aloe Anthraquinones Using PEG/Salt Aqueous Two-Phase System

The anthraquinones were extracted from Curacao aloe leaves. Aqueous two-phase system (ATPS) of polyethylene glycol (PEG)/salt, coupled with spectrophotometry and high performance liquid chromatography (HPLC) were employed for the first time as an attractive alternative for the downstream processing of aloe anthraquinones, mainly for the removal of the impurities without additional steps. The influence factors such as molecular mass and concentration of PEG, type, and concentration of neutral salt, temperature, and pH on the phase partition behavior of ATPS had been studied. Under the optimal condition, the highest extraction yield 90.54% was obtained in PEG phase using PEG-6000/(NH₄)₂SO₄ system to a mass ratio of 2:1 at 40°C, pH 3.0 with 0.6 g sodium chloride added. The reverse extraction of anthraquinones from the PEG phase was achieved with a recovery of 70.15% by adjusting the pH. Meanwhile, the PEG could be recycled. The major components in aloe anthraquinones of aloe-emodin and chrysophanol were analyzed by HPLC before and after ATPS extraction process. Compared with conventional purification methods, this technique can be completed in one operation; besides it is low-cost and environmentally friendly.     

Application of Aqueous Two‐Phase Systems for the Potential Extractive Fermentation of Cyanobacterial Products

The potential use of aqueous two‐phase systems (ATPS) to establish a viable protocol for the in situ recovery of cyanobacterial products was evaluated. The evaluation of system parameters such as poly (ethylene glycol) (PEG) molecular mass, concentration of PEG and salt was carried out to determine the conditions under which Synechocystis sp. PCC 6803 cell and cyanobacterial products, i.e., β‐carotene and lutein, become concentrated in opposite phases. PEG‐phosphate ATPS proved to be unsuitable for the recovery of cyanobacterial products due to the negative effect of the salt upon the cell growth. The use of ATPS PEG‐dextran (6.6 % w/w PEG 3350, 8.4 % w/w dextran 66900, TLL 17.3 % w/w, V_R 1.0, pH 7) and (4.22 % w/w PEG 8000, 9.77 % w/w dextran 66900, TLL 18 % w/w, V_R 1.0, pH 7) resulted in the growth of cyanobacteria (Synechocystis sp. PCC 6803) and the concentration of lutein in opposite phases. However, β‐carotene was seen to concentrate in the top phase together with the biomass. The results reported here demonstrate the potential application of ATPS to establish the conditions for an extractive fermentation prototype process for the recovery of cyanobacterial products.     

Development and Evaluation of PEG-Lithium Citrate Salt Based Aqueous Two Phase System and Its Application in Partitioning of Proteins from Fish Industry Effluent

A aqueous two phase system (ATPS) comprising of PEG (Average mol. Wt: 4000, 6000, 8000) – lithium citrate salt-water systems were studied. The basic studies like binodal curve data generation and equilibrium studies were carried out. Furthermore, the binodal model and Othmer-Tobias and Bancroft models for phase equilibria were used for reproducing the experimental binodal data and phase equilibrium composition data, respectively. Good agreement was obtained with the experimental binodal data and tie line data with the models. The effective excluded volume values were obtained from the binodal model for the present ATPS. The tie line length was determined through the phase equilibrium composition data. This system was used to partition crude proteins of the fish industry effluent. The effects of PEG and salt weight fraction in terms of tie line length and effective excluded volume on partitioning coefficient of crude protein were studied in detail. From the results it was observed that, the crude proteins present in the fish effluent were partitioned in the PEG rich phase and the maximum partition coefficient of 7.82 was obtained. The results are discussed in the context of practical potential of this citrate based ATPS in separating crude proteins from fish industry effluent.     

The optimization of aqueous two‐phase extraction of lysozyme from crude hen egg white using response surface methodology

BACKGROUND: Aqueous two‐phase extraction is a versatile method for separating biological particles and macromolecules. In the present wok, the feasibility of using PEG 4000/potassium citrate aqueous two‐phase system (ATPS) for recovering and purifying lysozyme was investigated. Response surface methodology was used to determine an optimized ATPS for purification of lysozyme from crude hen egg white. RESULTS: Mathematical models concerning the purification of lysozyme from chicken egg white in polyethylene glycol 4000 (PEG 4000)/potassium citrate ATPS are established using response surface methodology. Screening experiments using fractional factorial designs show that the pH of the system significantly affects the recovery and purification of lysozyme. An optimized ATPS was proved to be at pH 5.5 and 30 °C and contained 18% (w/w) PEG, 16% (w/w) potassium citrate, 3.75% (w/w) potassium chloride (KCl). Under those conditions, the specific activity, purification factor and activity yield for lysozyme were 31100 U mg^?1, 21.11 and 103%, respectively. CONCLUSION: The PEG 4000/potassium citrate ATPS has the potential to be applied to establish bioprocesses for the primary recovery and partial purification of lysozyme. © 2012 Society of Chemical Industry     

Improving glutathione extraction from crude yeast extracts by optimizing aqueous two-phase system composition and operation conditions

PEG-Dextran and PEG-salt aqueous two-phase systems (ATPS) have been applied to separate glutathione (GSH) from crude yeast extracts. Single-factor experiments were carried out to determine the important factors influencing the partition coefficient and extraction yield. The effect of PEG molecular weight, phase-forming components, PEG and Dextran concentration, pH value, and temperature on the GSH partitioning behavior in ATPS was investigated. Three factors, Dextran concentration, pH value, and temperature, were confirmed to have significant influence on the partition coefficient and extraction yield. These factors were further analyzed with the aid of central composite rotatable design and response surface methodology. The optimal conditions for GSH extraction in the PEGDextran system were determined, including PEG molecular weight 6,000, 10% PEG concentration, 14% Dextran concentration, pH 5.2, and temperature 32 °C. A high extraction yield (83.55%) of GSH from crude yeast extracts was achieved under these optimized conditions. This work is very helpful for developing one efficient and cost-effective process for the separation and purification of GSH from yeast broths.     

Continuous aqueous two-phase systems devices for the recovery of biological products

Aqueous two-phase systems (ATPS) have proved to be a suitable technique for the recovery of biological products. Although ATPS have been in the field of primary recovery and purification of products for several years, the majority of the studies exploiting ATPS are usually based on batch mode operation. Reports on the potential of using continuous ATPS are not common. This review attempts to present a practical analysis of selected devices employed for ATPS continuous processing, from the conventional column contactors to novel designed mixer-settler units. A critical analysis of operational and design parameters that impact the system performance is presented. Current trends on the implementation of continuous ATPS approaches are discussed, together with the major challenges faced for the generic adoption of the technique. Conclusions are drawn on the major contribution of previous studies in the field to provide a better understanding of the technique for the newcomers.     

Partition of alkaline protease in aqueous two-phase systems of polyethylene glycol 1000 and potassium phosphate

This article presents a study of polyethylene glycol 1000 (PEG1000)/potassium phosphate aqueous two-phase systems (ATPSs) forBacillus subtilis NS99 alkaline protease extraction. The objectives were to evaluate effects of system pH (7.5, 8.5,9.5, and 10.5), and NaCl concentration (0,4,7, and 10% (w/w)) on ATPS binodal curves, effects of system pH, NaCl concentration, and tie-line length (TLL) on alkaline protease partition coefficient (K) and yield (Y%) at room temperature (30±2 ‡C). Casein hydrolysis was used for determination of alkaline protease activity. It was revealed that system pH had the slightest effect on locations of binodal curves (except at pH 10.5). In contrast, addition of NaCl appeared to have a significant effect on phase characteristics since binodal curves of systems with NaCl (4-10% (w/w)) shifted significantly towards the origin in comparison to the ones without NaCl. Increased NaCl concentration from 4 to 10% (w/w), however, showed trivial influence on locations of the binodal curves. Changes of system compositions due to variation in system pH, TLL, and NaCl concentrations obviously resulted in varied obtainable K and Y% of alkaline proteases. Longer TLL and higher pH generally resulted in higher K. In contrast, the lower NaCl concentration, the higher K. Since the same phase volume ration (1:1) was used throughout the experiments, Y% depended solely on K. The most suitable PEG1000/potassium phosphate ATPS was determined at pH 9.5, and comprised PEG1000, potassium phosphate, and NaCl 18.0,13.0, and 0% (w/w), respectively. This system resulted in considerably high K, and Y% of 20.0, and 95.1%, respectively. Information from this study will be important for further development of an ATPS extraction unit for alkaline protease recovery.     

Optimization of Rhizopus niveus Lipase Partitioning by an Aqueous Biphasic System

An unconventional aqueous two‐phase system (ATPS) composed of polyethylene glycol (PEG) and sodium carbonate was developed and optimized by employing response surface methodology for separation of Rhizopus niveus lipase. A five‐level central composite design was applied to evaluate the optimal level of three process variables in order to obtain maximum lipase separation. Experimental data were analyzed by regression and a polynomial model was created which was found significant. The maximum partition coefficient was achieved with the system PEG 4000/sodium carbonate. Validation experiments confirmed the high accordance of predicted and experimental results. The optimized ATPS can be applied as a suitable cost‐effective system for lipase extraction.     

New aqueous two‐phase systems based on poly(ethylene oxide sulfide) (PEOS) and potassium phosphate for the potential recovery of proteins

A new aqueous two‐phase system (ATPS) based on a degradable polymer called poly(ethylene oxide sulfide) with a molecular weight of 33 000 g mol^?1 (identified as PEOS‐12) and potassium phosphate was exploited for the potential recovery of proteins. An initial characterisation of the ATPS was achieved by the construction of a phase diagram for the PEOS‐12/phosphate system. The protein partitioning behaviour of lysozyme and bovine serum albumin (BSA), selected as single model proteins, and B‐phycoerythrin (BPE) produced by Porphyridium cruentum in the new ATPS under increasing tie line length (TLL) conditions at constant phase volume ratio (V_r) and system pH was investigated. Both single proteins partitioned in the new ATPS, initially exhibiting bottom phase preference; however, lysozyme changed phase preference when TLL was increased. Fractionation of a complex model (production of BPE by P. cruentum) using PEOS‐12/phosphate ATPS was performed to evaluate the potential protein recovery from fermentation broth or cell homogenate. The proposed new ATPS proved to be suitable for the potential recovery of BPE from crude extract of P. cruentum. In general, a system comprising V_r = 1.0, 18% (w/w) PEOS‐12, 8% (w/w) phosphate and 30% (w/w) TLL at pH 7.0 provided conditions to concentrate BPE into the bottom phase (i.e. partitioning behaviour of BPE; lnK_BPE = ?1.8) with a protein recovery of 84%. The findings reported here demonstrate the potential application of the new ATPS for the recovery of proteins from complex biological suspensions. Copyright © 2006 Society of Chemical Industry     

Purification of Glucose Oxidase and β‐Galactosidase by Partitioning in a PEG‐Salt Aqueous Two‐Phase System in the Presence of PEG‐Derivatives

Abstract

Purification of glucose oxidase from Aspergillus niger and that of β‐galactosidase from Kluyveromyces lactis have been attempted using poly(ethylene glycol) (PEG)‐sodium sulfate aqueous two phase system (ATPS) in the presence of PEG‐derivatives, i.e. PEG‐Coomassie brilliant blue G‐250 and PEG‐benzoate, PEG‐palmitate and PEG‐TMA, respectively. The enzymes showed poor partitioning towards the PEG phase in comparison with other proteins in ATPS containing no ligands. Selective partitioning of other proteins was observed towards the PEG phase in the presence of PEG‐benzoate and PEG‐palmitate enriching β‐galactosidase in the salt phase whereas in the case of glucose oxidase, PEG‐Coomassie brilliant blue G‐250 derivative worked as a better affinity ligand for other proteins. A 19‐fold purification was obtained with the PEG dye derivative after 5 stage cross extractions with 80% recovery of glucose oxidase and an enrichment factor upto ～7 for β‐galactosidase with the PEG‐TMA derivative. The interaction of PEG‐benzoate and PEG‐TMA ligands with the active site of β‐galactosidase has been evaluated by molecular modeling. The effect of the molecular weight of glucose oxidase on its partitioning was confirmed as the molecular simulation shows strong affinity interaction of PEG‐glucoside with the enzyme.     

Extractive bioconversion of xylan for production of xylobiose and xylotriose using a PEG6000/sodium citrate aqueous two-phase system

Aqueous two-phase system (ATPS) was applied for extraction bioconversion of xylan by xylanase from Trichoderma viride. Phase diagrams for poly (ethylene glycol) (PEG) and sodium citrate were determined at room temperature. The ATPS composed of 12.99% (w/w) PEG6000 and 12.09% (w/w) sodium citrate was favorable for partition of xylanase and used for extraction bioconversion of xylan. Batch hydrolysis demonstrated that higher concentrations of xylobiose and xylotriose were obtained in the PEG6000/sodium citrate ATPS compared to those in the aqueous system. These results present the potential feasibility of production of xylo-oligosaccharides by extraction bioconversion in ATPS.