Microstructure and crystallization of melt‐mixed poly(ethylene terephthalate)/poly(ethylene isophthalate) blends

Physical blends of poly(ethylene terephthalate) (PET) and poly(ethylene isophthalate) (PEI), abbreviated PET/PEI (80/20) blends, and of PET and a random poly(ethylene terephthalate‐co‐isophthalate) copolymer containing 40% ethylene isophthalate (PET₆₀I₄₀), abbreviated PET/PET₆₀I₄₀ (50/50) blends, were melt‐mixed at 270°C for different reactive blending times to give a series of copolymers containing 20 mol % of ethylene isophthalic units with different degrees of randomness. ¹³C‐NMR spectroscopy precisely determined the microstructure of the blends. The thermal and mechanical properties of the blends were evaluated by DSC and tensile assays, and the obtained results were compared with those obtained for PET and a statistically random PETI copolymer with the same composition. The microstructure of the blends gradually changed from a physical blend into a block copolymer, and finally into a random copolymer with the advance of transreaction time. The melting temperature and enthalpy of the blends decreased with the progress of melt‐mixing. Isothermal crystallization studies carried out on molten samples revealed the same trend for the crystallization rate. The effect of reaction time on crystallizability was more pronounced in the case of the PET/PET₆₀I₄₀ (50/50) blends. The Young's modulus of the melt‐mixed blends was comparable to that of PET, whereas the maximum tensile stress decreased with respect to that of PET. All blend samples showed a noticeable brittleness. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 3076–3086, 2003     

Synthesis and characterization of poly(ethylene isophthalate‐co‐ethylene terephthalate) copolyesters

Poly(ethylene isophthalate‐co‐ethylene terephthalate) (PEIPET) copolymers of various compositions and molecular weights were synthesized by melt polycondensation and characterized in terms of chemical structure and thermal and rheological properties. At room temperature, all copolymers were amorphous and thermally stable up to about 400°C. The main effect of copolymerization was a monotonic increase of glass transition temperature (T_g) as the content of ethylene terephthalate units increased. The Fox equation accurately describes the T_g–composition data. The presence of ethylene terephthalate units was found to influence rheological behavior in the melt, with the Newtonian viscosity increasing as the content of ethylene terephthalate units increased. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 186–193, 2004     

Synthesis and non‐isothermal crystallization behavior of poly(ethylene phthalate‐co‐terephthalate)s

A series of poly(ethylene phthalate‐co‐terephthalate)s were synthesized by melt polycondensation of ethylene glycol (EG) with dimethyl phthalate (DMP) and dimethyl terephthalate (DMT) in various proportions. The DMT‐rich polymers were obtained with reasonably high molecular weights, whereas the DMP‐rich polymers were synthesized with relatively low molecular weights due to steric effects associated with the highly kinked DMP monomer. The compositions and thermal properties of the polymers were determined. The copolymers containing DMP in amounts of ≤ 21 mol% were crystallizable, whereas the other polymers were not. All the polymers exhibited a single glass transition temperature. Analysis of the measured glass transition temperatures and crystal melting temperatures confirmed that the DMT‐rich copolymers are random copolymers. The non‐isothermal crystallization behaviors of the DMT‐rich copolymers were investigated by calorimetry and modified Avrami analysis. The Avrami exponents n were found to range from 2.7 to 3.8, suggesting that the copolymers crystallize via a heterogeneous nucleation and spherulitic growth mechanism; that is, the incorporation of DMP units as the minor component does not change the growth mechanism of the copolymers. In addition, the activation energies of the crystallizations of the copolymers were determined; the copolymers were found to have higher activation energies than the PET homopolymer. Polym. Eng. Sci. 44:1682–1691, 2004. © 2004 Society of Plastics Engineers.     

Sequence analysis and fiber properties of a blend of poly(ethylene terephthalate) and poly(ethylene terephthalate‐co‐4,4′‐bibenzoate)

Blends of poly(ethylene terephthalate) (PET) and poly(ethylene terephthalate‐co‐4,4′‐ bibenzoate) (PETBB) are prepared by coextrusion. Analysis by ¹³C‐NMR spectroscopy shows that little transesterification occurs during the blending process. Additional heat treatment of the blend leads to more transesterification and a corresponding increase in the degree of randomness, R. Analysis by differential scanning calorimetry shows that the as‐extruded blend is semicrystalline, unlike PETBB15, a random copolymer with the same composition as the non‐ random blend. Additional heat treatment of the blend leads to a decrease in the melting point, T_m, and an increase in glass transition temperature, T_g. The T_m and T_g of the blend reach minimum and maximum values, respectively, after 15 min at 270°C, at which point the blend has not been fully randomized. The blend has a lower crystallization rate than PET and PETBB55 (a copolymer containing 55 mol % bibenzoate). The PET/PETBB55 (70/30 w/w) blend shows a secondary endothermic peak at 15°C above an isothermal crystallization temperature. The secondary peak was confirmed to be the melting of small and/or imperfect crystals resulting from secondary crystallization. The blend exhibits the crystal structure of PET. Tensile properties of the fibers prepared from the blend are comparable to those of PET fiber, whereas PETBB55 fibers display higher performance. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 1793–1803, 2004     

Crystallization kinetics of poly(1,4‐butylene‐co‐ethylene terephthalate)

The crystallization kinetics of poly(butylene terephthalate) (PBT), poly(ethylene terephthalate) (PET), and their copolymers poly(1,4‐butylene‐co‐ethylene terephthalate) (PBET) containing 70/30, 65/35 and 60/40 molar ratios of 1,4‐butanediol/ethylene glycol were investigated using differential scanning calorimetry (DSC) at crystallization temperatures (T_c) which were 35–90 °C below equilibrium melting temperature . Although these copolymers contain both monomers in high proportion, DSC data revealed for copolymer crystallization behaviour. The reason for such copolymers being able to crystallize could be due to the similar chemical structures of 1,4‐butanediol and ethylene glycol. DSC results for isothermal crystallization revealed that random copolymers had a lower degree of crystallinity and lower crystallite growth rate than those of homopolymers. DSC heating scans, after completion of isothermal crystallization, showed triple melting endotherms for all these polyesters, similar to those of other polymers as reported in the literature. The crystallization isotherms followed the Avrami equation with an exponent n of 2–2.5 for PET and 2.5–3.0 for PBT and PBETs. Analyses of the Lauritzen–Hoffman equation for DSC isothermal crystallization data revealed that PBT and PET had higher growth rate constant G_o, and nucleation constant K_g than those of PBET copolymers. © 2001 Society of Chemical Industry     

Effect of poly(ethylene glycol) on the solid‐state polymerization of poly(ethylene terephthalate)

Poly(ethylene glycol) (PEG) and end‐capped poly(ethylene glycol) (poly(ethylene glycol) dimethyl ether (PEGDME)) of number average molecular weight 1000 g mol^?1 was melt blended with poly(ethylene terephthalate) (PET) oligomer. NMR, DSC and WAXS techniques characterized the structure and morphology of the blends. Both these samples show reduction in T_g and similar crystallization behavior. Solid‐state polymerization (SSP) was performed on these blend samples using Sb₂O₃ as catalyst under reduced pressure at temperatures below the melting point of the samples. Inherent viscosity data indicate that for the blend sample with PEG there is enhancement of SSP rate, while for the sample with PEGDME the SSP rate is suppressed. NMR data showed that PEG is incorporated into the PET chain, while PEGDME does not react with PET. Copyright © 2005 Society of Chemical Industry     

Oxygen barrier properties of PET copolymers containing bis(2‐hydroxyethyl)hydroquinones

A series of poly[ethylene‐co‐bis(2‐ethoxy)hydroquinone terephthalate], PET‐co‐BEHQ copolymers were prepared by polymerization of various substituted bis(2‐hydroxyethyl)hydroquinones (BEHQs), dimethyl terephthalate (DMT), and ethylene glycol (EG). In addition to copolymers containing 6–16.5 mol % BEHQ, the homopolymer of BEHQ with dimethyl terephthalate, p(BEHQ‐T), was also prepared. The thermal and barrier properties of amorphous materials were studied. As the amount of comonomer was increased, the T_g and T_m of the materials decreased relative to those of PET. Oxygen permeability also decreased with increasing comonomer content. This improvement in barrier‐to‐oxygen permeability was primarily due to a decrease in solubility of oxygen in the polymer. All of the copolymers tested displayed similar oxygen diffusion coefficients. The decrease in solubility correlates with the decrease in T_g. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 934–942, 2003     

Effects of molecular weight on phase structure of poly(ethylene terephthalate)/poly(ethylene 2,6‐naphthalate) blends

The phase structure of poly(ethylene terephthalate)/poly(ethylene 2,6‐naphthalate) (PET/PEN) blends was studied in relation to the molecular weight. The samples were prepared by both solution blends, which showed two glass‐transition temperatures (T_g), and melt blends (MQ), which showed a single T_g, depending on the composition of the blends. The T_g of the MQ series was independent of the molecular weight of the homopolymer, although the degree of transesterification in the blends was affected by the molecular weight. The MQ series showed two exotherms during the heating process of a differential scanning calorimetry scan. The peak temperature and the heat flow of the exotherms were affected by the molecular weight of the homopolymers. The strain‐induced crystallization of the MQ series suggested the independent crystallization of PET and PEN. Based on the results, a microdomain structure of each homopolymer was suggested. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 2428–2438, 2005     

Synthesis and characterization of poly(ethylene terephthalate‐co‐isophthalate)s with low content of isophthalate units

The objective of this work was to study the effect of the introduction of low amounts of isophthalate units on the mechanical properties, crystallization rates, and thermal parameters of poly(ethylene terephthalate). For this reason a series of five random poly(ethylene terephthalate‐co‐isophthalate) copolymers, containing 0.5, 1, 1.5, 2, and 4 mol % isophthalic acid, were prepared by the melt polycondensation process. The intrinsic viscosity of copolymers ranged between 0.7 and 0.8 dL/g. The increase of isophthalate content resulted in a significant decrease of the crystallization rates, but in a small decline of tensile strength, Young's modulus, and elongation at break, whereas tensile strength at yield point remained almost unaffected. Also, a decrease in the melting point was recorded, whereas the glass‐transition temperature was only very slightly affected. The higher decrease for the aforementioned parameters was noted for the copolymer with 4 mol % isophthalate units content. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 1931–1941, 2002     

Poly(ethylene terephthalate‐co‐isophthalate) copolyesters obtained from ethylene terephthalate and isophthalate oligomers

A series of poly(ethylene terephthalate‐co‐isophthalate) copolyesters containing upto 50%‐mole of isophthalic units were prepared by polycondensation from ethylene terephthalate and ethylene isophthalate fractions of linear oligomers containing from 5 to 6 repeating units in average. The polyesters were obtained in good yields and with high‐molecular‐weights. The microstructure of the copolyesters was studied as a function of reaction time by ¹³C‐NMR showing that a random distribution of the comonomers was achieved since the earlier stages of polycondensation. The melting temperature and enthalpy of the copolyesters decreased with the content of isophthalic units so that copolyesters containing more than 25% of these units were amorphous. Isothermal crystallization studies made on crystalline copolyesters revealed that the crystallization rate of copolyesters decreased with the content in isophthalic units. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Crystallization behavior of poly(ethylene terephthalate‐co‐neopentyl terephthalate‐co‐ethylene isophthalate‐co‐neopentyl isophthalate) copolyester and its application in laminated tin‐free steel

A low crystallinity, the copolyester poly(ethylene terephthalate‐co‐neopentyl terephthalate‐co‐ethylene isophthalate‐co‐neopentyl isophthalate) (PENIT) was synthesized and applied for laminated tin‐free steel. The structures and thermal properties of the copolyester were characterized by ¹H‐NMR, thermogravimetry analysis, differential scanning calorimetry, wide‐angle X‐ray diffraction, and polarized optical microscopy. Differential scanning calorimetry, wide‐angle X‐ray diffraction, and polarized optical microscopy results show that the crystallization ability of the copolyester decreased obviously. Meanwhile, the peel strength, crystallinity, and water‐vapor permeability of the copolyester film were also measured at varied lamination temperatures. The result confirm that an improvement in the lamination temperature led to an increased ratio of amorphous PENIT to crystalline PENIT and decreased structural orientation, and the decrease in the structural orientation sped up the increase in the rate of water‐vapor permeability. On the basis of the purpose of reducing a detrimental effect on the corrosion resistance caused by water permeation, a reasonable lamination temperature was selected. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42308.     

Synthesis and characterization of a poly(ether–ester) copolymer from poly(2,6 dimethyl‐1,4‐phenylene oxide) and poly(ethylene terephthalate)

A series of poly(ether–ester) copolymers were synthesized from poly(2,6 dimethyl‐1,4‐phenylene oxide) (PPO) and poly(ethylene terephthalate) (PET). The synthesis was carried out by two‐step solution polymerization process. PET oligomers were synthesized via glycolysis and subsequently used in the copolymerization reaction. FTIR spectroscopy analysis shows the coexistence of spectral contributions of PPO and PET on the spectra of their ether–ester copolymers. The composition of the poly(ether–ester)s was calculated via ¹H NMR spectroscopy. A single glass transition temperature was detected for all synthesized poly(ether–ester)s. T_g behavior as a function of poly(ether–ester) composition is well represented by the Gordon‐Taylor equation. The molar masses of the copolymers synthesized were calculated by viscosimetry. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci, 2006     

The complicated influence of branching on crystallization behavior of poly(ethylene terephthalate)

The randomly branched poly(ethylene terephthalate) (BPET) was prepared by bulk polycondensation from dimethyl terephthalate (DMT) and ethylene glycol (EG), with 0.4–5.0 mol % (with respect to DMT) of glycerol (GL) as a branching agent. The glass transition and crystallization behavior was studied by differential scanning calorimetry (DSC). It was found that the glass transition temperature of BPET reduced with the increasing content of GL until 1.2 mol %, and then increases a little at high degrees of branching. When compared with a linear PET, the crystallization temperature of BPET from the melt shifted to higher temperature as GL content was smaller than 1.2 mol %, and then became lower while GL load was added. Nonisothermal crystallization kinetics was studied through the modified Avrami analysis. It was revealed that the overall crystallization rate parameter of BPET became larger when the GL content was less than 1.2 mol %, then turned to lower at higher branching degree. This indicated that low degree of branching could enhance the overall crystallization of poly(ethylene terephthalate) (PET), whereas high degree of branching in the range of 3.5–5.0 mol % would block the development of crystallization. On the basis of Hoffman's secondary crystallization theory, the product σσ_e of the free energy of formation per unit area of the lateral and folding surface was calculated. According to the change of the product σσ_e with the degree of branching, a possible explanation was presented to illuminate this diverse effect of different degrees of branching on crystallization. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Crystallization of 2‐methyl‐1,3‐propanediol substituted poly(ethylene terephthalate). I. Thermal behavior and isothermal crystallization

Differential scanning calorimetry (DSC) was used to evaluate the thermal behavior and isothermal crystallization kinetics of poly(ethylene terephthalate) (PET) copolymers containing 2‐methyl‐1,3‐propanediol as a comonomer unit. The addition of comonomer reduces the melting temperature and decreases the range between the glass transition and melting point. The rate of crystallization is also decreased with the addition of this comonomer. In this case it appears that the more flexible glycol group does not significantly increase crystallization rates by promoting chain folding during crystallization, as has been suggested for some other glycol‐modified PET copolyesters. The melting behavior following isothermal crystallization was examined using a Hoffman–Weeks approach, showing very good linearity for all copolymers tested, and predicted an equilibrium melting temperature (T_m⁰) of 280.0°C for PET homopolymer, in agreement with literature values. The remaining copolymers showed a marked decrease in T_m⁰ with increasing copolymer composition. The results of this study support the claim that these comonomers are excluded from the polymer crystal during growth. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 2592–2603, 2006     

Synthesis and characterization of copolymers based on poly(butylene terephthalate) and ethylene oxide‐poly(dimethylsiloxane)‐ethylene oxide

A series of thermoplastic elastomers based on ethylene oxide‐poly(dimethylsiloxane)‐ethylene oxide (EO‐PDMS‐EO), as the soft segment, and poly(butylene terephthalate) (PBT), as the hard segment, were synthesized by catalyzed two‐step, melt transesterification reaction of dimethyl terephthalate (DMT) with 1,4‐butanediol (BD) and α,ω‐dihydroxy‐(EO‐PDMS‐EO). Copolymers with a content of hard PBT segments between 40 and 90 mass % and a constant length of the soft EO‐PDMS‐EO segments were prepared. The siloxane prepolymer with hydrophilic terminal EO units was used to improve the miscibility between the polar comonomers, DMT and BD, and the nonpolar PDMS. The molecular structure and composition of the copolymers were determined by ¹H‐NMR spectroscopy, whereas the effectiveness of the incorporation of α,ω‐dihydroxy‐(EO‐PDMS‐EO) into the copolymer chains was verified by chloroform extraction. The effects of the structure and composition of the copolymers on the melting temperatures and the degree of crystallinity, as well as on the thermal degradation stability and some rheological properties, were studied. It was demonstrated that the degree of crystallinity, the melting and crystallization temperatures of the copolymers increased with increasing mass fraction of the PBT segments. The thermal stability of the copolymers was lower than that of PBT homopolymer, because of the presence of thermoliable ether bonds in the soft segments. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Analysis of physical properties of PET/CD‐PET polyblend hollow fiber and its kinetics of alkaline hydrolysis

Cationic dyeable poly(ethylene terephthalate) (CD‐PET) was formed by copolymerizing dimethylterephthalate (DMT),5‐sodium sulfonate dimethyl isophthalate (SIPM) with a molar ratio of 2% and ethylene glycol (EG). Blends of regular poly(ethylene terephthalate) (PET) and CD‐PET were spun into hollow fibers. The fibers were then treated with aqueous NaOH. This study investigated the physical properties of PET/CD‐PET polyblend hollow fibers and their kinetic behavior of alkaline hydrolysis using differential scanning calorimetry (DSC), wide‐angle X‐ray diffraction (WAXD), the density gradient method, a gel permeation chromatograph (GPC), a rheometer, and regression analysis of the statistical method. For the alkaline hydrolysis kinetics equation of PET, CD‐PET, and PET/CD‐PET polyblend materials: ? dW/dt = KC^αA^β, β values of chip and POY/ FOY hollow fibers are equal to 1. Moreover, R² of the kinetics equation of chip/POY/FOY for a from 1.09–1.35/1.08–1.32/1.06–1.29 were better than those of a = 1. Experimental results indicate that the rate constant of alkaline hydrolysis was CD‐PET hollow fiber > PET/CD‐PET polyblend hollow fibers > PET hollow fiber and FOY > POY > > Chip. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 3601–3610, 2002     

Nonisothermal crystallization behavior of biodegradable poly(butylene terephthalate‐co‐butylene adipate‐co‐ethylene terephthalate‐co‐ethylene adipate) copolyester

A series of biodegradable aliphatic‐aromatic copolyester, poly(butylene terephthalate‐co‐butylene adipate‐co‐ethylene terephthalate‐co‐ethylene adipate) (PBATE), were synthesized from terephthalic acid (PTA), adipic acid (AA), 1,4‐butanediol (BG) and ethylene glycol (EG) by direct esterification and polycondensation. The nonisothermal crystallization behavior of PBATE copolyesters was studied by the means of differential scanning calorimeter, and the nonisothermal crystallization kinetics were analyzed via the Avrami equation modified by Jeziorny, Ozawa analysis and Z.S. Mo method, respectively. The results show that the crystallization peak temperature of PBATE copolyesters shifted to lower temperature at higher cooling rate. The modified Avrami equation could describe the primary stage of nonisothermal crystallization of PBATE copolyesters. The value of the crystallization half‐time (t_1/2) and the crystallization parameter (Z_c) indicates that the crystallization rate of PBATE copolyesters with more PTA content was higher than that with less PTA at a given cooling rate. Ozawa analysis was not suitable to study the nonisothermal crystallization process of PBATE copolyesters, but Z.S. Mo method was successful in treatingthis process. POLYM. ENG. SCI., 2011. © 2011 Society of Plastics Engineers     

Hybrid poly(ethylene terephthalate)/silica nanocomposites prepared by in‐situ polymerization

The nanocomposites, based on hybrid poly(ethylene terephthalate) (PET)/silica nanoparticles, were prepared via in‐situ condensation polymerization of terephthalic acid and ethylene glycol in the presence of silica nanoparticles pretreated with a silane coupling agent. Such a polymerization process ensured that the silica nanoparticles were well dispersed in PET matrix with the size ranging from 40 to 60 nm, which was confirmed by transmission electron microscope (TEM) observation. Attributed to the unique bonding between SiO₂ nanoparticle and PET, the crystallization behavior of PET was improved significantly, at a low temperature in particular. To further explore the effects of silica nanoparticles on crystallization, extensive differential scanning calorimeter (DSC) measurements were performed in an attempt to reveal the impact of the morphology of the dispersed silica nanoparticle (i.e., sphere or gel‐like) on the peak temperature during melting as well as the amount of heat involved in crystallization. The influences of the structure of polyether glycol (PEG) used for PET preparation as well as the addition of glass fibres (GF) were also investigated using DSC. It was concluded that the synergy among silica nanoparticles, modified PEG, and GFs lowers both T_g and T_m of PET, thus facilitating the injection processes in application. POLYM. COMPOS. 28:42–46, 2007. © 2007 Society of Plastics Engineers     

Characterization and thermal‐oxidative degradation behavior of poly(ethylene terephthalate‐co‐4,4′‐bibenzoate) prepared via direct esterification technique

A series of poly(ethylene terephthalate‐co‐4,4′‐bibenzoate)s (PETBBs) were prepared via direct esterification from the monomers of terephthalic acid (TPA), 4,4′‐biphenyl dicarboxylic acid (BPDA), and ethylene glycol (EG) with different molar ratios. The chemical compositions of the obtained PETBBs, investigated by H¹‐NMR, were identical with the feed ratio, and the high molecular weights of PETBBs were confirmed by GPC analysis. The glass transition, crystallization, and melting behavior of them were measured by DSC; the results indicated that, in the range of 5–25 mol% of BPDA addition, the glass transition temperature (T_g) increased almost linearly and the melting temperature (T_m) decreased with increasing content of BPDA unit. As expected, the crystallization of PETBB became difficult with increasing introduction of BPDA, explained by higher crystallization temperature and smaller crystallization enthalpy from the glassy state. This decrease of crystallization rate may be beneficial to film processing. Moreover, owing to the introduction of rigid‐rod BPDA unit, the initial and maximum thermal‐oxidative decomposition temperatures were enhanced. The kinetic analysis of the thermal‐oxidative degradation indicated that the apparent activation energies of degradation for these PETBBs became higher than that of PET. POLYM. ENG. SCI., 2012. © 2012 Society of Plastics Engineers     

Effects of dispersing agents on dispersity and mechanical properties of carbon black/PET

Three kinds of dispersing agents, all copolyesters, were synthesized from the polycondensation reaction of dimethyl terephthalate (DMT), dimethyl isophthalate (DMI), sebacic acid (SA), and 1,4-butandiol (BD). Copolyester from DMT, SA, and BD was designated as PBTS; from DMT, SA, DMI, and BD as PBTIS; and from DMT, DMI, and BD as PBTI. Carbon black masterbatches were prepared by mixing carbon black into the dispersing agents in a Brabender Plasticorder PLE331. Using single screw extruder, masterbatches were compounded with poly(ethylene terephthalate) in 3 wt% concentration and mechanical properties of the compounds were investigated. Gel permeation chromatography data implied that thermal degradation of polymeric dispersing agents was not very significant. Capillary rheometer tests showed that PBTI has the highest viscosity and shear sensitivity of the three dispersing agents. Volume resistivities of each masterbatch were increased as the rotor rpm of the Brabender and mixing time increased. Transmission electron micrographs showed that dispersion of carbon black was enhanced by increasing the melt viscosity of the dispersing agent. The performance and mechanical characteristics of carbon-black-filled PET compounds depends directly on the dispersion quality of the carbon black in the masterbatch. Mechanical properties of compounds were improved by increasing dispersion of carbon black and increasing numbers of rigid aromatic groups in the copolyester dispersing agent.