Effects of B2O3 Addition on the Dielectric and Ferroelectric Properties of Ba0.7Sr0.3TiO3 Ceramics

The effects of B₂O₃ addition on the sintering behavior and the dielectric and ferroelectric properties of Ba_0.7Sr_0.3TiO₃ (BST) ceramics were investigated. The dielectric and ferroelectric properties of a BST sample with 0.5 wt% B₂O₃ sintered at <1150°C were as good as those of undoped BST sintered at 1350°C, and the dielectric loss was better. When >1.0 wt% B₂O₃ was added to BST, the overdoped B₂O₃ did not form a liquid phase or volatilize; it remained in the samples and formed a secondary phase that lowered the sintering behavior and the dielectric and ferroelectric properties of the BST.     

Effect of Glass Additions on BaO–TiO2–WO3 Microwave Ceramics

The effect of glass addition on the properties of BaO–TiO₂-WO₃ microwave dielectric material N-35, which has Q = 5900 and K = 35 at 7.2 GHz for samples sintered at 1360°C, was investigated. Several glasses including B₂O₃, SiO₂, 5ZnO–2B₂O₃, and nine other commercial glasses were selected for this study. Among these glasses, one with a 5 wt% addition of B₂O₃ to N-35, when sintered at 1200°C, had the best dielectric properties: Q = 8300 and K = 34 at 8.5 GHz. Both Q and K increased with firing temperature as well as with density. The Q of N-35, when sintered with a ZnO–B₂O₃ glass system, showed a sudden drop in the sintering temperature to about 1000°C. The results of XRD, thermal analysis, and scanning electron microscopy indicated that the chemical reaction between the dielectric ceramics and glass had a greater effect on Q than on the density. The effects of the glass content and the mixing process on the densification and microwave dielectric properties are also presented. Ball milling improved the densification and dielectric properties of the N-35 sintered with ZnO–B₂O₃.     

Low-Temperature Firing and Microwave Dielectric Properties of Ca[(Li1/3Nb2/3)0.84Ti0.16]O3−δ Ceramics for LTCC Applications

The effects of LiF and ZnO–B₂O₃–SiO₂ (ZBS) glass combined additives on phase composition, microstructures, and microwave dielectric properties of Ca[(Li_1/3Nb_2/3)_0.84Ti_0.16]O_3−δ (CLNT) ceramics were investigated. The LiF and ZBS glass combined additives lowered the sintering temperature of CLNT ceramics effectively from 1150° to 880°C. The main diffraction peaks of all the specimens split due to the coexistence of the non-stoichiometric phase (A) and stoichiometric phase (B), which all possess CaTiO₃-type perovskite structures. The transformation from A into B became accelerated with the increase of LiF or ZBS content. ZBS glass restrained the volatilization of lithium salt, which greatly affected the microstructures and microwave dielectric properties. CLNT ceramics with 2 wt% LiF and 3 wt% ZBS sintered at 900°C for 2 h show excellent dielectric properties: ɛ_r=34.3, Q × f =17 400 GHz, and τ_f=−4.6 ppm/°C. It is compatible with Ag electrodes, which makes it a promising ceramic for low-temperature cofired ceramics technology application.     

Synthesis of BaCu(B2O5) Ceramics and their Effect on the Sintering Temperature and Microwave Dielectric Properties of Ba(Zn1/3Nb2/3)O3 Ceramics

BaCu(B₂O₅) ceramics were synthesized and their microwave dielectric properties were investigated. BaCu(B₂O₅) phase was formed at 700°C and melted above 850°C. The BaCu(B₂O₅) ceramic sintered at 810°C had a dielectric constant (ɛ_r) of 7.4, a quality factor ( Q × f ) of 50 000 GHz and a temperature coefficient of resonance frequency (τ_f) of −32 ppm/°C. As the BaCu(B₂O₅) ceramic had a low melting temperature and good microwave dielectric properties, it can be used as a low-temperature sintering aid for microwave dielectric materials for low temperature co-fired ceramic application. When BaCu(B₂O₅) was added to the Ba(Zn_1/3Nb_2/3)O₃ (BZN) ceramic, BZN ceramics were well sintered even at 850°C. BaCu(B₂O₅) existed as a liquid phase during the sintering and assisted the densification of the BZN ceramic. Good microwave dielectric properties of Q × f =16 000 GHz, ɛ_r=35, and τ_f=22.1 ppm/°C were obtained for the BZN+6.0 mol% BaCu(B₂O₅) ceramic sintered at 875°C for 2 h.     

Influence of V2O5 Additions to 5Li2O–1Nb2O5–5TiO2 Ceramics on Sintering Temperature and Microwave Dielectric Properties

The effects of the addition of V₂O₅ on the sintering behavior, microstructure, and microwave dielectric properties of 5Li₂O–1Nb₂O₅–5TiO₂ (LNT) ceramics have been investigated. With low-level doping of V₂O₅ (≤3 wt%), the microstructure of the LNT ceramic changed from a special two-level intergrowth structure into a two-phase composite structure with separate grains. And the sintering temperature of the LNT ceramics could be lowered to around 900°C by adding a small amount of V₂O₅ without much degradation in microwave dielectric properties. Typically, better microwave dielectric properties of ɛ_r=41.7, Q × f =7820 GHz, and τ _f =45 ppm/°C could be obtained for the 1 wt% V₂O₅-doped ceramics sintered at 900°C.     

Effect of Li2CO3 Addition on the Sintering Temperature and Microwave Dielectric Properties of Mg2V2O7 Ceramics

Li₂CO₃ was added to Mg₂V₂O₇ ceramics in order to reduce the sintering temperature to below 900°C. At temperatures below 900°C, a liquid phase was formed during sintering, which assisted the densification of the specimens. The addition of Li₂CO₃ changed the crystal structure of Mg₂V₂O₇ ceramics from triclinic to monoclinic. The 6.0 mol% Li₂CO₃-added Mg₂V₂O₇ ceramic was well sintered at 800°C with a high density and good microwave dielectric properties of ɛ _r=8.2, Q × f =70 621 GHz, and τ_f=−35.2 ppm/°C. Silver did not react with the 6.0 mol% Li₂CO₃-added Mg₂V₂O₇ ceramic at 800°C. Therefore, this ceramic is a good candidate material in low-temperature co-fired ceramic multilayer devices.     

Sintering and Microwave Dielectric Properties of the LiNb0.63Ti0.4625O3 Ceramics with the B2O3–SiO2 Liquid-Phase Additives

The effect of B₂O₃–SiO₂ liquid-phase additives on the sintering, microstructure, and microwave dielectric properties of LiNb_0.63Ti_0.4625O₃ ceramics was investigated. It was found that the sintering temperature could be lowered easily, and the densification and dielectric properties of LiNb_0.63Ti_0.4625O₃ ceramics could be greatly improved by adding a small amount of B₂O₃–SiO₂ solution additives. No secondary phase was observed for the ceramics with B₂O₃–SiO₂ additives. With the addition of 0.10 wt% B₂O₃–SiO₂, the ceramics sintered at 900°C showed favorable microwave dielectric properties with ɛ_r=71.7, Q × f =4950 GHz, and τ_f=−2.1 ppm/°C. The energy dispersive spectra analysis showed an excellent co-firing interfacial behavior between the LiNb_0.63Ti_0.4625O₃ ceramic and the Ag electrode. It indicated that LiNb_0.63Ti_0.4625O₃ ceramics with B₂O₃–SiO₂ solution additives have a number of potential applications on passive integrated devices based on the low-temperature co-fired ceramics technology.     

Low-Temperature Sintering Barium Titanate-Based X8R Ceramics with Nd2O3 Dopant and ZnO–B2O3 Flux Agent

To demonstrate that barium titanate-based ceramics could be sintered at a low temperature thus reducing the cost of capacitor production, systematic investigation has been made on the structure and dielectric properties of barium titanate-based X8R ceramics, doped with various Nd₂O₃ content and different ZnO–B₂O₃ solution as the sintering aids. The dielectric ceramic powder with good permittivity and low dielectric loss were obtained at a sintering temperature of 900°C, meeting X8R specifications. Transmission electron microscopy and EDS analysis shows a high concentration of Nd element in the boundary regions, which verifies the beneficial role of Nd in facilitating the formation of core-shell structure. The results also suggest that the developed BaTiO₃-based ceramics may serve as a promising candidate for fabricating cheap multilayer capacitors with pure Ag as inner electrode.     

Electrical Properties of Sr0.7Ba0.3TiO3 Ceramics Doped with Nb2O5, 3Li2O · 2SiO2, and Bi2O3

The electrical properties of Sr_0.5Ba_0.3TiO₃ in the presence of Nb₂O₅ as a donor, 3Li₂O · 2SiO₂ as a sintering agent, and Bi₂O₃ as a dopant have been studied. When the compositions of the ceramics were 1 mol Sr_0.7Ba_0.3TiO₃+ 0.5 mol% Nb₂O₅+ 2 mol% 3Li₂O · 2SiO₂+ 0.2 mol% Bi₂O₃, the ceramics were sintered at 1100°C and exhibited the following characteristics: apparent dielectric constant ɛ, 25000; loss factor tan δ, 2%; insulating resistivity ρ_j, 10¹⁰Ω· cm; variation of dielectric constant with temperature Δɛ/ɛ (−25° to +85°C), +10%, −14%. ɛ and tan δ show only small changes with frequency. The study shows this ceramic can be used in multilayer technology.     

Low-Temperature Sintering and Microwave Dielectric Properties of the Zn2SiO4 Ceramics

B₂O₃ was added to nominal composition Zn_1.8SiO_3.8 (ZS) ceramics to decrease their sintering temperature for application to low-temperature cofired ceramic (LTCC) devices. B₂O₃ reacted with SiO₂ to form a liquid phase containing SiO₂ and B₂O₃. The composition and melting temperature of the liquid phase depended on the sintering temperature and the B₂O₃ content. The specimen containing 20.0 mol% of B₂O₃ sintered at 900°C exhibited high microwave dielectric properties of Q × f =53 000 GHz, ɛ _r=5.7, and τ_f=−16 ppm/°C, confirming the promising potential of the B₂O₃-added ZS ceramics as candidate materials for the LTCC devices.     

A New Microwave Dielectric Ceramic for LTCC Applications

A new low-sintering temperature microwave dielectric ceramic, the Li₂TiO₃ solid solution, was found and investigated in the Li₂O–Nb₂O₅–TiO₂ system. The compound with the composition of Li_2.081Ti_0.676Nb_0.243O₃ crystallizes as a monoclinic structure. This new microwave dielectric ceramic shows a relatively low permittivity (∼20), high Q × f values up to 50 000 (7.8 GHz), and near-zero temperature coefficients (13 ppm/°C), which were obtained via sintering at 1100°C. The addition of ≤2 wt% B₂O₃ was very effective in lowering the sintering temperature ( T _s), and dense ceramics could be obtained at T _s≤900°C. The addition of B₂O₃ does not induce apparent degradation in the microwave properties but lowers the τ_f value to near zero. It is obvious that the ceramics could be promising candidates for multilayer low-temperature co-fired ceramics applications.     

Microwave Dielectric Properties of 5Li2O–0.583Nb2O5–3.248TiO2 Ceramics with V2O5

The effects of V₂O₅ addition on the sintering behavior, microstructure, and the microwave dielectric properties of 5Li₂O–0.583Nb₂O₅–3.248TiO₂ (LNT) ceramics have been investigated. With addition of low-level doping of V₂O₅ (≤2 wt%), the sintering temperature of the LNT ceramics could be lowered down to around 920°C due to the liquid phase effect. A secondary phase was observed at the level of 2 wt% V₂O₅ addition. The addition of V₂O₅ does not induce much degradation in the microwave dielectric properties but lowers the τ_f value to near zero. Typically, the excellent microwave dielectric properties of ɛ_r=21.5, Q × f =32 938 GHz, and τ_f=6.1 ppm/°C could be obtained for the 1 wt% V₂O₅-doped sample sintered at 920°C, which is promising for application of the multilayer microwave devices using Ag as an internal electrode.     

High-Q Microwave Dielectric Materials Based on the Spinel Mg2TiO4

Composite ceramics based on the spinel Mg₂TiO₄ were prepared by a conventional mixed-oxide route. To achieve the temperature stabilization of the dielectric constant, each of the composites was added with 7 mol% CaTiO₃. The effect of the substitution of isovalent Co for Mg on the microstructure and the microwave dielectric properties of the composite ceramics was also investigated. A maximum Q × f value of around 150–160 THz was obtained for the undoped Mg₂TiO₄, whereas a reduced Q × f value was observed for an increase in the Co concentration in the system (1− x )Mg₂TiO₄− x Co₂TiO₄. Upon doping with 7 mol% CaTiO₃, the Q × f value passed through a maximum with increasing Co concentration. Adding ZnO–B₂O₃ to the composite system based on Co-doped Mg₂TiO₄ resulted in a reduction of the sintering temperature by 150°–200°C without any significant degradation in the Q × f value.     

Microwave Dielectric Properties and Low-Temperature Sintering of Ba0.60Sr0.40TiO3 Ceramics

In the present work, the sintering behaviors and dielectric properties of Ba_0.60Sr_0.40TiO₃ (BST) ceramics with the addition of BaCu(B₂O₅) were investigated in detail. The results indicated that the addition reduced the sintering temperature of BST by about 500°C. It was suggested that a liquid phase BaCu(B₂O₅) assisted the densification of BST ceramics at lower temperatures. For a low-level BaCu(B₂O₅) addition (2.0 mol%), the BST sample sintered at 950°C for 5 h displayed good dielectric properties, with a moderate dielectric constant (ɛ=2553) and a low dielectric loss (tan δ=0.00305) at room temperature and at 10 kHz. The sample showed 45.9% tunability at 10 kHz under a dc electric field of 30 kV/cm. At the frequency of 0.984 GHz, BST-added 2.0 mol% BaCu(B₂O₅) possessed a dielectric constant of 2204 and a Q value of 146.7.     

The Li2O–Nb2O5–TiO2 Composite Microwave Dielectric Ceramics with Adjustable Permittivities

A group of new y M-phase/(1− y ) Li_{2+ x} Ti_{1−4 x} Nb_{3 x} O₃ composite ceramics with adjustable permittivities for low-temperature co-fired ceramic applications was initially investigated in the study. The 0.5 M-phase/0.5 Li_{2+ x} Ti_{1−4 x} Nb_{3 x} O₃ ( x =0.01, 0.02, 0.04, 0.06, 0.081) composite ceramics were first investigated to find the appropriate "Li₂TiO₃ss" composition ( x value). The best dielectric properties of ɛ_r=40.1, Q × f values up to 9318 GHz, τ_f=25 ppm/°C, were obtained for the ceramics composites at x =0.02. Based on the good dielectric properties, the suitable "Li₂TiO₃ss" composition with x =0.02 was mixed with the Li_1.0Nb_0.6Ti_0.5O₃ powder as the ratio of y "M-phase"/(1− y ) "Li₂TiO₃ss" ( y =0.2, 0.4, 0.5, 0.6, 0.8). By adjusting the y values, the group of composite ceramics could exhibit largely are adjustable permittivities varying from ∼20 to ∼60, while Q × f and τ_f values relatively good. Nevertheless, in this study, because there are interactions between the M-phase and Li₂TiO₃ss during sintering process, their microwave dielectric properties could not be predicted precisely by the empirical model.     

Effects of La2O3/ZnO Additives on Microstructure And Microwave Dielectric Properties of Zr0.8Sn0.2TiO4 Ceramics

Dielectric ceramics of Zr_0.8Sn_0.2TiO₄ containing La₂O₃ and ZnO as sintering aids were prepared and investigated for microstructure and microwave dielectric properties. Low-level doping with La₂O₃ and ZnO (up to 0.30 wt%) is good for densification and dielectric properties. These additives do not affect the dielectric constant and the temperature coefficient. Dielectric losses increase significantly at additive levels higher than 0.15 wt%. The combined additives La₂O₃ and ZnO act as grain growth enhancers. With 0.15 wt% additives, a ceramic having a dielectric constant, a quality factor, and a temperature coefficient of frequency at 4.2 GHz of 37.6, 12 800, and –2.9 ppm/°C, respectively, was obtained. The quality factor was considerably improved by prolonged sintering.     

Effects of B2O3 on the Phase Stability of Ba2Ti9O20 Microwave Ceramic

Preparation of dense and phase-pure Ba₂Ti₉O₂₀ is generally difficult using solid-state reaction, since there are several thermodynamically stable compounds in the vicinity of the desired composition and a curvature of Ba₂Ti₉O₂₀ equilibrium phase boundary in the BaO–TiO₂ system at high temperatures. In this study, the effects of B₂O₃ on the densification, microstructural evolution, and phase stability of Ba₂Ti₉O₂₀ were investigated. It was found that the densification of Ba₂Ti₉O₂₀ sintered with B₂O₃ was promoted by the transient liquid phase formed at 840°C. At sintering temperatures higher than 1100°C, the solid-state sintering became dominant because of the evaporation of B₂O₃. With the addition of 5 wt% B₂O₃, the ceramic yielded a pure Ba₂Ti₉O₂₀ phase at sintering temperatures as low as 900°C, without any solid solution additive such as SnO₂ or ZrO₂. The facilities of B₂O₃ addition to the stability of Ba₂Ti₉O₂₀ are apparently due to the eutectic liquid phase which accelerates the migration of reactant species.     

Low-Temperature Sintering of (Ba0.6Sr0.4)TiO3

An addition of just 0.4 wt% Li₂O to (Ba_0.6Sr_0.4)TiO₃ powder was able to reduce the sintering temperature to ≤900°C and produce ceramics with a relative density of 97%. Small amounts of two secondary phases were formed during this process: Li₂TiO₃ and Ba₂TiO₄. The addition of Li₂O depresses the ferroelectric character of the (Ba_0.6Sr_0.4)TiO₃ and, as a result, reduces the permittivity, improves the temperature coefficient of permittivity, and reduces the dielectric losses. The tunability shows no significant variation with Li₂O concentration and remains between 16.5% and 13.5%. A low-temperature sintering mechanism was proposed. The mechanism involves the intermediate formation of BaCO₃, its melting and the incorporation of Li⁺ into the BST. The sintering mechanism can be characterized as reactive liquid-phase sintering.     

Microwave Dielectric Properties of CaTiO3-CaAl1/2Nb1/2O3 Ceramics Doped with Li3NbO4

The microwave dielectric properties of CaTi_{1− x} (Al_1/2Nb_1/2) _x O₃ solid solutions (0.3 ≤ x ≤ 0.7) have been investigated. The sintered samples had perovskite structures similar to CaTiO₃. The substitution of Ti⁴⁺ by Al³⁺/Nb⁵⁺ improved the quality factor Q of the sintered specimens. A small addition of Li₃NbO₄ (about 1 wt%) was found to be very effective for lowering sintering temperature of ceramics from 1450–1500° to 1300°C. The composition with x = 0.5 sintered at 1300°C for 5 h revealed excellent dielectric properties, namely, a dielectric constant (ɛ_r) of 48, a Q × f value of 32 100 GHz, and a temperature coefficient of the resonant frequency (τ_f) of −2 ppm/K. Li₃NbO₄ as a sintering additive had no harmful influence on τ_f of ceramics.     

Effects of Heating Rate on the Sintering Behavior and the Dielectric Properties of Ba0.7Sr0.3TiO3 Ceramics Prepared by Boron-Containing Liquid-Phase Sintering

The effects of heating rate on the sintering behavior and the dielectric properties of Ba_0.7Sr_0.3TiO₃ ceramics prepared by boron-containing liquid-phase sintering were investigated. When 0.5 wt% B₂O₃ was added to Ba_0.7Sr_0.3TiO₃, sintering was achieved at ∼1150°C, and the overdoped B₂O₃ did not form an adequate amount of liquid phase or volatilize; it remained in the samples and formed a secondary phase. A transition broadening was observed as the heating rate increased. As the heating rate increased, the Curie temperature increased and the maximum dielectric constant ( k _max) at the Curie temperature decreased. This result is attributable to a decrease in the diffuseness parameter (δ) and the tetragonality ( c / a ).