Aerobic granulation in a sequencing batch reactor (SBR) for industrial wastewater treatment.

Aerobic granulation seems to be an a attractive process for COD removal from industrial wastewater, characterised by a high content of soluble organic compounds. In order to evaluate the practical aspects of the process, comparative experimental tests are performed on synthetic and on industrial wastewater, originating from pharmaceutical industry. Two pilot plants are operated as sequencing batch bubble columns. Focus was put on the feasibility of the process for high COD removal and on its operational procedure. For both wastewaters, a rapid formation of aerobic granules is observed along with a high COD removal rate. Granule characteristics are quite similar with respect to the two types of wastewater. It seems that filamentous bacteria are part of the granule structure and that phosphorus precipitation can play an important role in granule formation. For both wastewaters similar removal performances for dissolved biodegradable COD are observed (> 95%). However, a relatively high concentration of suspended solids in the outlet deteriorates the performance with regard to total COD removal. Biomass detachment seems to play a non-negligible role in the current set-up. After a stable operational phase the variation of the pharmaceutical wastewater caused a destabilisation and loss of the granules, despite the control for balanced nutrient supply. The first results with real industrial wastewater demonstrate the feasibility of this innovative process. However, special attention has to be paid to the critical aspects such as granule stability as well as the economic competitiveness, which both will need further investigation and evaluation.     

低温下SBR污水处理工艺运行研究

研究了低温和常温条件下SBR系统的运行状况，探索了低温条件下不同有机负荷与曝气时间的对应关系。常温SBR系统启动期为6d，低温系统启动期为8d，每天运行周期均为8h。低温系统的COD去除随曝气时间的变化趋势与常温系统基本相同，与常温系统的运行状况相比，低温系统在相同有机负荷情况下，其出水COD比常温系统稍低，但没有大的区别。常温和低温两种系统中，同一负荷每天出水COD浓度大致相同，但不同有机负荷系统的出水COD显著不同。     

Aerobic granular sludge: a promising technology for decentralised wastewater treatment.

In order to evaluate the characteristics of aerobic granular sludge, a sequencing batch reactor, feeding with synthetic wastewater at the organic loading rate of 8 kg COD/m3 d, was employed on the laboratory scale. Granules occurred in the reactor within 1 week after the inoculation from conventional flocculent sludge. Aerobic granular sludge was characterised by the outstanding settling properties and considerable contaminates removal efficiencies. The SVI30 values were in the range of 20 to 40 ml g(-1). However, the sludge volume index of short settling time (e.g. SVI10--10 min) is suggested to describe the fast settling properties of aerobic granular sludge. The potential application in the decentralised system is evaluated from the point view of footprint and high bioactivity. The occurrence of sloughing, resulting from the outgrowth of filamentous organisms, would be responsible for the instability of aerobic granules. The starvation phase should therefore be carefully controlled for the maintenance and stability of aerobic granular sludge system.     

High COD wastewater treatment in an aerobic SBR: treatment of effluent from a small farm goat's cheese dairy.

In France, small goat's cheese dairies using traditional craft methods often have no profitable solution for dealing with the whey byproduct of their cheesemaking activity: it is usually mixed with the cleaning wastewater which, in the absence of other possibilities, is then discharged directly into the environment. The volume of such wastewater is small but it has a high COD of around 12-15 g/L. An aerobic SBR was proposed as a method for treating the mixture of wastewater and whey and the first installation was set up on a farm with 170 goats. Its operations were monitored for 7.5 months, particularly in order to measure any excess volume of sludge and to check that such excess remained within acceptable limits, given the high COD of the effluent requiring treatment. The results obtained show that the treated wastewater was of excellent quality, well within the most rigorous discharge norms. With this type of wastewater, excess sludge was produced in only very low amounts with 0.2 g of SS/g of COD. Moreover, the sludge proved to be quick settling which made it possible to: i) maintain a high level of SS in the reactor (up to 15 g/L); ii) withdraw sludge with concentrations reaching 30 g/L after 2 hours of settling. This resulted in a low volume of excess sludge (less than 5% of treated volume), making such aerobic biological treatment in an SBR competitive when compared to the straightforward spreading of all the wastewater.     

Aerobic biological treatment of thermophilically digested sludge

Aerobic biological treatment of digested sludge was studied in a continuously operated laboratory set-up. An aerated reactor was filled with thermophilically digested sludge from the Moscow wastewater treatment plant and inoculated with special activated sludge. It was then operated at the chemostat mode at different flow rates. Processes of nitrification and denitrification, as well as dephosphatation, occurred simultaneously during biological aerobic treatment of thermophilically digested sludge. Under optimal conditions, organic matter degradation was 9.6%, the concentrations of ammonium nitrogen and phosphate decreased by 89 and 83%, respectively, while COD decreased by 12%. Dewaterability of digested sludge improved significantly. The processes were found to depend on hydraulic retention time, oxygen regime, and temperature. The optimal conditions were as follows: hydraulic retention time 3-4 days, temperature 30-35 degrees C, dissolved oxygen levels 0.2-0.5 mg/L at continuous aeration or 0.7-1 mg/L at intermittent aeration. Based on these findings, we propose a new combined technology of wastewater sludge treatment. The technology combines two stages: anaerobic digestion followed by aerobic biological treatment of digested sludge. The proposed technology makes it possible to degrade the sludge with conversion of approximately 45% volatile suspended solids to biogas, to improve nitrogen and phosphorus removal in reject water from sludge treatment units, and to achieve removal of malodorous substances after 8-9 days of anaerobic-aerobic sludge treatment.     

恒液位SBR工艺处理城市污水的研究

采用恒液位SBR工艺对城市污水处理进行实验研究。研究影响恒液位SBR工艺脱氮除磷效果的缺氧-好氧循环、沉淀时间、进水流量等因素。结果表明:在最佳工况下处理城市污水时,COD、TN、TP和NH3-N去除率分别为88.21%~91.04%、68.04%~70.45%、95.26%~96.11%和89.76%~91.17%,说明采用恒液位SBR工艺处理城市污水是可行的。     

Two-stage SBR for treatment of oil refinery wastewater.

A two-stage sequencing batch reactor (SBR) system was used for treatment of oily wastewater with COD and oil and grease (O&G) concentrations ranging from 1,722-7,826 mg/L and 5,365-13,350 mg/L, respectively. A suitable start-up protocol was developed using gradual increase in oily wastewater composition with methanol as the co-substrate. This strategy enabled a short acclimation period of 12 days for the sludge in the two-stage SBR to adapt to the oily wastewater. After acclimation, the 1st stage and 2nd stage SBRs were able to achieve COD removals of 47.0+/-2.4% and 95.3+/-0.5%, respectively. The 1st stage SBR was able to achieve 99.8+/-0.1% of O&G removal and effluent O&G from the 1st stage SBR was only 6+/-2 mg/L. The 2nd stage SBR was used to further remove COD in the effluent from the 1st stage SBR. The final effluent from the 2nd stage SBR had a COD concentration of 97+/-16 mg/L with no detectable O&G content. Thus, a two-stage SBR system was shown to be feasible for treating high strength oily wastewater to meet the local discharge standards.     

核晶凝聚诱导造粒法同步去除硬度和有机物的研究

针对石油废水中无机离子与有机物共存的特点,构建了一体化核晶凝聚诱导造粒装置,探究了该体系对石油废水中总硬度和溶解性有机物的去除效果和去除原理.研究结果表明:当氢氧化钠投加量为250 mg/L时,总硬度、钙离子和COD的去除率分别为88.35％、90％和52.92％.结合SEM和XRD表征结果发现钙离子主要以碳酸钙形式附...     

Floc size distribution in a stirred suspension.

This paper focuses on the distribution of alumino-humic flocs found in a stirred suspension. Distributions were scaled using the transformation u = d/dL in which d is floc diameter and dL its arithmetic mean value and fitted by a gamma distribution. Flocs were treated as monofractal with solids mass concentration specified by C = A'rhos (d/do)D-3 in which A' is a packing coefficient, rhos the density of the floc solids, D the fractal dimension and do a reference size. It was shown that the overall solids concentration (M) complies with the dependence M proportional to NA'dDL-S(D) in which N is the number of flocs per unit volume and S(D) a distribution moment. Initial estimates of A' and D were obtained from analysis of floc sedimentation behaviour. From knowledge of the base parameters, the calculated value of M did not match the measured M and varied with shear. This was attributed to a kinematic influence on C over and beyond changes associated with the response of dL to shear. Issues of self-similarity were examined and it was concluded that distributions did not display strict self-similarity. Data are provided on the size distribution found in the flocculators of a treatment works at full scale.     

搅拌槽内流体力学特性的数值模拟研究

采用FLUENT6.3.26软件求解气液两相流,自由液面的捕捉采用VOF(volume of fluid)法,辅以标准k-ε湍流模型数值求解气液两相流时均方程,使用了半隐式SIMPLE(Semi-Implicit Method for Pressure-Linked Equations)算法求解速度与压力耦合方程组,旨在研究搅拌槽在搅拌过程中流体流动的力学特性,分析比较了不同水深处的水流沿半径方向的径向速度、切向速度及轴向速度的规律,经过研究和分析发现模拟的速度值与实验值吻合良好,为搅拌槽的设计和运行提供了参考。     

DAT-IAT工艺及设备的研究与应用

对序批式活性污泥法 (SBR)的一种新型变法DAT -IAT工艺的工作原理、特点、工艺设计参数、三种不同动力形式的滗水器及在天津开发区污水处理厂的工作实例作了介绍。论述了此项新型变法的工艺、设备特征及节省工程投资、减少占地及设备的三个优点。     

Study of the biological N removal over nitrite in a physico-chemical-biological treatment of digested pig manure in a SBR.

SBR technology is used to treat the supernatant from mesophilic anaerobic digestion of piggery wastewater. The novelty of the treatment consists in the use of a final coagulation/flocculation step inside the SBR cycle to reach the legal COD effluent standard. The pH changes introduced by the use of FeCl(3) do not affect the nitrifying activity. The SBR treatment includes a strategy to the control of oxygen supply and ammonia concentrations inside the digester to favor the biological nitrogen removal over nitrite, which makes the process more economical. The influence of several of these parameters on the AOB biomass activity is studied in this paper.     

Nutrient removal and microbial granulation in an anaerobic process treating inorganic and organic nitrogenous wastewater.

The sustainable anaerobic nitrogen removal and microbial granulation were investigated by using a laboratory anaerobic granular sludge bed reactor, treating synthetic (inorganic and organic) wastewater and piggery waste. From inorganic synthetic wastewater, lithoautotrophic ammonium oxidation to nitrite/nitrate was observed by an addition of hydroxylamine. Also, the results revealed that the Anammox intermediates (particularly, hydrazine) contents in the substrate would be one of the important parameters for success of the anaerobic nitrogen removal process. The results from organic synthetic wastewater show that if the Anammox organism were not great enough in the startup of the process, denitritation and anaerobic ammonification would be a process prior to the Anammox reaction. The anaerobic ammonium removal from the piggery waste was performed successfully, probably due to the Anammox intermediates contained in the substrate. This reactor shows a complex performance including the Anammox reaction and HAP crystallization, as well as having partial denitritation occurring simultaneously. From the activity test, the maximum specific N conversion rate was 0.1 g NH4-N/g VSS/day (0.77 g T-N/g VSS/day), indicating that potential denitritation is quite high. The NO2-N/NH4-N ratio to Anammox is 1.17. The colour of the biomass treating the piggery waste changed from black to dark red. It was also observed that the red-colored granular sludge had a diameter of 1-2 mm. The settleability assessment of the granular sludge revealed that the granular sludge had a good settleability even though it was worse than that of seed granular sludge.     

On-site treatment of a motorway service area wastewater using a package sequencing batch reactor (SBR).

A sequencing batch reactor (SBR) treating the effluent of a motorway service station in the south of England situated on a major tourist route was investigated. Wastewater from the kitchens, toilets and washrooms facilities was collected from the areas on each side of the motorway for treatment on-site. The SBR was designed for a population equivalent (p.e.) of 500, assuming an average flow of 100 m3/d, influent biochemical oxygen demand (BOD) of 300 mg/l, and influent suspended solids (SS) of 300 mg/l. Influent monitoring over 8 weeks revealed that the average flow was only 65 m3/d and the average influent BOD and SS were 480 mg/l and 473 mg/l respectively. This corresponded to a high sludge loading rate (F:M) of 0.42 d(-1) which accounted for poor performance. Therefore the cycle times were extended from 6 h to 7 h and effluent BOD improved from 79 to 27 mg/l.     

佳木斯东区污水处理厂SBR工艺的低温快速启动

为在低温(水温14℃)下完成佳木斯东区污水处理厂SBR工艺的快速启动,采用复合生物茵剂、粪便水和活性污泥同时投加、先异步后同步的复合培茵方法对污水处理厂进行了调试.结果表明,该方法可有效克服低水温、贫营养、缺水、跑泥等问题对启动过程的不利影响,在进水CODCr、NH3-N和TP分别在140～430 mg/L、20～40 mg/L和2～3 mg/L大幅度波动的情况下,实现出水的快速持续达标,平均出水浓度分别为42.1 mg/L、6.4 mg/L和0.9 mg/L,满足了<城镇污水处理厂污染物排放标准>(GB 18918-2002)中一级A标准.     

The performance of a nitrogen-fixing SBR.

A laboratory study has successfully demonstrated that a nitrogen deficient thermomechanical pulping wastewater can be effectively treated in a sequencing batch reactor (SBR) operated under conditions of biological nitrogen fixation (the N-ViroTech process). In comparison to continuous stirred tank reactor activated sludge (CSTR-AS) configurations operated under either nitrogen fixing or nitrogen supplemented conditions, slightly lower removals of dissolved organic material were observed in the SBR. However, this was largely offset by significantly better suspended solids removal in the SBR, which contributes to the overall COD discharge. The settleability and dewaterability of sludge produced by the SBR was significantly better than that obtained from the nitrogen fixing CSTR-AS reactors, and comparable to that of a nitrogen supplemented system. Consistently low total and dissolved nitrogen discharges from the N-ViroTech systems demonstrated the advantage of this system over ones requiring nitrogen supplementation. The feast-famine regime of an SBR-type configuration has significant potential for the application of this technology in the treatment of nitrogen deficient waste streams, particularly those in which conventional single-stage systems may be susceptible to sludge bulking problems.     

Specific SBR population behaviour as revealed by comparative dynamic simulation analysis of three full-scale municipal SBR wastewater treatment plants.

Three full-scale municipal sequential batch reactor (SBR) wastewater treatment plants (WWTPs) were investigated by dynamic simulation studies using ASM1. All three WWTPs showed similar kinetic and stoichiometric conditions in the SBR population behaviour after calibration of the models. The simulation results detected only a discrepancy to the ammonia online data during and shortly after shock loading under anoxic and anaerobic conditions that so far could not be adjusted by the ASM1 model. However, these differences did not severely affect the quality of the simulations nor the effluent flows. Additionally, in all cases a dynamic alpha factor curve occurred during the aeration phases that was verified by further oxygen transfer measurements. This might reveal new aspects for the process control, design and simulation of SBR WWTPs. A short lag phase was detected in many cases at the beginning of the first aeration phase.     

Removal efficiency of subsurface vertical flow constructed wetlands for different organic loads.

Using subsurface vertical flow constructed wetlands (SSVFCWs) with intermittent loading it is possible to fulfil the stringent Austrian effluent standards regarding nitrification. For small plants (less than 500 persons) standards for ammonia nitrogen concentration have to be met at water temperatures higher than 12 degrees C, effluent concentrations and treatment efficiencies for organic matter have to be met the whole year around. According to the Austrian design standards the required surface area for SSVFCWs treating wastewater was 5 m2 per person. Within the first part of an Austrian research project the goal was to optimise, i.e. minimise the surface area requirement of vertical flow beds. Therefore, three SSVFCWs with a surface area of 20 m2 each have been operated in parallel. The organic loads applied were 20, 27 and 40 g COD/m2/d, which corresponds to a specific surface area requirement of 4, 3 and 2 m2 per PE, respectively. The paper compares the effluent concentrations and elimination efficiencies of the three parallel operated beds. It could be shown that a specific area demand of 4 m2 per person is suitable to be included in the revision of the Austrian design standard. Additionally it could be shown that during the warmer seasons (May-October) when the temperature of the effluent is higher than 12 degrees C the specific surface area might be further reduced; even 2 m2 per person has been proven to be adequate.     

Detroit River phosphorus loads: Anatomy of a binational watershed

As a result of increased harmful algal blooms and hypoxia in Lake Erie, the US and Canada revised their phosphorus loading targets under the 2012 Great Lakes Water Quality Agreement. The focus of this paper is the Detroit River and its watershed, a source of 25% of the total phosphorus (TP) load to Lake Erie. Its load declined 37% since 1998, due chiefly to improvements at the regional Great Lakes Water Authority Water Resource Recovery Facility (WRRF) in Detroit and phosphorus sequestered by zebra and quagga mussels in Lake Huron. In addition to the 54% of the load from Lake Huron, nonpoint sources contribute 57% of the TP load and 50% of the dissolved reactive phosphorus load, with the remaining balance from point sources. After Lake Huron, the largest source is the WRRF, which has already reduced its load by over 40%. Currently, loads from Lake Huron and further reductions from the WRRF are not part of the reduction strategy, therefore remaining watershed sources will need to decline by 72% to meet the Water Quality Agreement target - a daunting challenge. Because other urban sources are very small, most of the reduction would have to come from agriculturally-dominated lands. The most effective way to reduce those loads is to apply combinations of practices like cover crops, buffer strips, wetlands, and applying fertilizer below the soil surface on the lands with the highest phosphorus losses. However, our simulations suggest even extensive conservation on those lands may not be enough.     

SBR类污水处理厂升级改造工艺选择及运行

以太湖流域9座采用SBR及其改进工艺的污水处理厂升级改造工程为例,介绍了该工艺升级改造方案的选择和达标难度分析,并在案例分析的基础上,总结了SBR类污水处理厂改造工程在设计和运行时需要注意的问题。