EXPERIMENTAL INVESTIGATIONS ON SUBSURFACE DAMAGE IN ROTARY ULTRASONIC MACHINING OF GLASS BK7

The present study aimed to establish an exact comprehension of the subsurface damage patterns generated during rotary ultrasonic machining (RUM) of glass BK7 process. First, the subsurface damage of the specimens produced with and without ultrasonic using three different diamond tools was compared and characterized by means of the bonded interface sectioning technique. Then, the RUM scratching tests were conducted on the polished specimen surfaces with two diamond tools to investigate the subsurface damage formation mechanisms involved in formal RUM process. The damage characteristics of the RUM scratches were investigated with respect to the kinematics principles of the abrasives and the dynamic fracture theory of the brittle material. As a result, three types of RUM-induced subsurface damage were identified: pulverization, chipping and cracking. The pulverization layer characterized by finer debris was just populated near the top surface of the RUM specimen without extending into the interior material. The finer debris should emerge simultaneously, resulting from the increased strain rate and the decreased dynamic fracture toughness of the material, both of which were aroused by the inertia loading of the abrasive when reaching the vertex of its sinusoidal trajectory.     

Effect on crystalline structure of AISI M2 steel using tungsten–thorium electrode through MRR,EWR, and surface finish

To investigate on the crystalline structure of AISI M2 steel by using tungsten–thorium electrode in electrical discharge machining (EDM) process was studied. Furthermore, the investigation were carried out for finding the value of material removal rate (MRR), electrode wear rate (EWR) and surface roughness (SR) of tool steel material depending upon three variable input process parameters. On the basis of weight loss, the value of MRR and EWR were calculated at optimized process parameter. Subsequently, surface topography of the processed material were examined through different characterization techniques like scanning electron microscopy (SEM), Optical surface profiler (OSP) and Atomic force microscopy (AFM), respectively. In XRD study, broadening of the peak was observed which confirmed the change in material properties due to the homogeneous dispersion of the particles inside the matrix. Lowest surface roughness and MRR of 0.001208 mg/min was obtained. Minimum surface roughness was obtained 1.12 μm and 2.18427 nm by OSP and AFM study, respectively. Also, minimum EWR was found as 0.013986 mg/min.     

高体积分数SiCp/Al复合材料旋转超声铣磨加工的试验研究

由于大量高硬度增强相SiC颗粒的存在,高体积分数铝基碳化硅（SiCp/Al）复合材料的机械加工十分困难。旋转超声加工被认为是加工这种材料的有效方法。通过超声辅助划痕试验,分析高体积分数SiCp/Al复合材料旋转超声铣磨加工的材料去除机理。在超声振动的作用下,材料中铝基体发生塑性变形,其表面得到夯实;SiC增强相被锤击成细小的颗粒而发生脱落,形成较大的空洞。由于材料加工的缺陷大多产生于SiC颗粒的去除过程中,SiC颗粒的去除方式对加工表面的质量起着决定性的作用,选择合适的工艺参数可以有效提高加工表面质量。旋转超声加工工艺特征试验表明,超声振动可有效降低切削力;主轴转速对轴向切削力的影响最大,其次是进给速度,切削深度对轴向切削力的影响较小;另外主轴转速对表面质量的影响效果也最大,并随主轴转速的增大表面粗糙度增大。因此在加工过程中,可以适当加大切削深度,在保证加工质量的基础上,选择较大的进给速度,在保证刀具寿命的前提下,选择合适的主轴转速,以获得较优的加工表面质量和加工效率。     

Rotary ultrasonic machining: effects of tool natural frequency on ultrasonic vibration amplitude

Rotary ultrasonic machining (RUM) is a hybrid machining process that combines the material removal mechanisms of grinding and ultrasonic machining. RUM has been applied to hole-making for a wide range of materials. It is known that ultrasonic vibration amplitude has significant effects on cutting force, torque, and surface finish in RUM. One experimental observation that has been reported in the literature multiple times states that different tools show different vibration amplitudes on the same ultrasonic power level. However, no analyses can be found in the literature to explain this observation. The existence of this knowledge gap makes it difficult to explain some experimentally obtained trends or to conduct more realistic physics-based modeling work. The objectives of this research are to understand the effects of tool natural frequency on ultrasonic vibration amplitude in RUM, to provide an explanation to the observation and verification of measurement methods, and also to guide tool design and selection in RUM. Ultrasonic vibration amplitudes of tools are measured by three methods and compared. It is found that tool natural frequency significantly affects ultrasonic vibration amplitude. The tool with its natural frequency closest to that of the ultrasonic power supply (20?kHz) generates the highest ultrasonic vibration amplitude on every ultrasonic power level tested.     

硬脆材料旋转超声加工技术的研究现状及展望

旋转超声加工是一种复合特种加工技术,它复合了传统超声加工和普通磨削加工的材料去除方式,在提高硬脆材料去除效率、减小切削力、提高加工精度和表面完整性等方面具有显著优势。自旋转超声加工技术发明至今,国内外学者开展了大量的有关旋转超声加工装备及工艺的研究工作,并且已在几乎所有主要的硬脆难加工材料中得到实际应用。本研究在简要概述旋转超声加工技术的基本原理和发展过程基础上,总结国内外学者在材料去除机理、工艺特性、加工新形式以及装备研发等几方面的主要研究成果,并对旋转超声加工技术的发展趋势及值得关注的问题进行展望。     

Ultrasonic vibration assisted grinding of hard and brittle linear micro-structured surfaces

In this paper, a novel ultrasonic vibration assisted grinding (UVAG) technique was presented for machining hard and brittle linear micro-structured surfaces. The kinematics of the UVAG for micro-structures was first analyzed by considering both the vibration trace and the topological features on the machined surface. Then, the influences of the ultrasonic vibration parameters and the tilt angle on the ground quality of micro-structured surfaces were investigated. The experimental results indicate that the introduction of ultrasonic vibration is able to improve the surface quality (The roughness SR_a was reduced to 78 nm from 136 nm), especially in guaranteeing the edge sharpness of micro-structures. By increasing the tilt angle, the surface roughness can be further reduced to 56 nm for a 59% improvement in total. By using the preferred UVAG parameters realized by orthogonal experiments, a micro cylinder array with surface roughness of less than 50 nm and edge radius of less than 1 μm was fabricated. The primary and secondary sequence of the grinding parameters obtained by the orthogonal experiments are as follows: feed rate, tilt angle of workpiece, depth of grinding, vibration frequency and amplitude. The spindle speed in the range of 1000 rpm–3000 rpm does not significantly affect the machined micro-structured surface roughness. Finally, more micro-structures including a micro V-groove array and a micro pyramid array were machined on binderless WC as well as SiC ceramic by means of the UVAG technique. The edge radius on the V-grooves and pyramids are both less than 1 μm, indicating the feasibility of UVAG in machining hard and brittle micro-structured surfaces for an improved surface quality.     

Theoretical model for cutting force in rotary ultrasonic milling of dental zirconia ceramics

Rotary ultrasonic machining or ultrasonic vibration assisted grinding has superior performance in machining hard and brittle materials, such as dental zirconia ceramics. However, there are few reports about cutting force modeling of rotary ultrasonic milling (RUM) for dental ceramics, especially for cutting force model in feed direction. In this study, the theoretical model of cutting force both in axial direction and feed direction is proposed under the assumption that brittle fracture is the primary mechanism of material removal in RUM of dental ceramics. The effective cutting time and material removal volume have been analyzed to develop the cutting force model. Besides, the number of active abrasive particles has been calculated for the first time during the modeling. The effect of overlapping and intersection of fracture zone in peripheral direction on material removal volume has also been considered via the parameters K ₁ and K ₂. In addition, the relationships between the cutting force and input variables are revealed through the theoretical model. Finally, pilot experiments of RUM on dental zirconia ceramics are conducted to verify the theoretical model. The experimental results are consistent well with the model predictions. Therefore, the theoretical model can be applied to evaluate the cutting force in RUM of dental ceramics.     

Abrasive wear of embossed surfaces with convex domes

Some soil-burrowing animals and other biological organisms living in contact with abrasive materials have surfaces optimized for reducing drag and wear. In this study, bio-inspired embossed surfaces consisting of an array of convex domes are investigated to quantify their abrasive wear resistance properties. The experimental procedure proposed in this work is based on sliding seven different embossed surface specimens against an abrasive material for distances up to 3948.9 m with sliding velocities up to 3.02 m/s. The seven specimens consist of 20 mm-wide convex domes made of bakelite and calcium carbonate fixed to flat steel substrates. Quartz sand particles having three different sizes are used as abrasive material for the tests. Experimental results are analyzed and guidelines for designing embossed surfaces, which are optimized to minimize abrasive wear, are proposed.     

Kinematics and trajectory analysis of the fixed abrasive lapping process in machining of interdigitated micro-channels on bipolar plates

The fixed abrasive lapping process is presented to investigate its ability and accuracy in machining of interdigitated micro-channels on bipolar plates that are used in the proton exchange membrane fuel cell. A kinematical equation to describing the relative movement between the fixed abrasive lapping plate and workpiece is developed and used to numerically simulate the trajectories of a single diamond abrasive and fixed diamond abrasives with 17 different arraying forms, respectively. It is shown that the lapping trajectory can be superposed periodically when the rotation ratio is a rational number. By assessing the uniformity of lapping trajectories and opening ratio of the bipolar plate the optimized rotation ratio is obtained which is 1:1, and the best arraying form of the fixed diamond abrasives on the lapping plate has been obtained as well that is the arraying form of C4. Then, a set of fixed abrasive lapping tests were conducted to explore its ability in machining of interdigitated micro-channels on bipolar plates. It is found that larger material removal rate can be achieved by employing bigger lapping pressure and higher rotation speed for both copper and stainless steel samples considered in this study. The maximum cell power density is found to be about 165 mW cm⁻² by testing the performance of a single micro fuel cell with a bipolar plate characterized by interdigitated micro-channels that shows a good cell performance.     

An analytical model of rotary ultrasonic milling

Rotary ultrasonic machining is currently being used as a manufacturing method for advanced ceramic materials, but its complexity has hindered its acceptance in industry. For this technology to gain wider acceptance, it must first be scientifically better understood. The majority of published rotary ultrasonic machining (RUM) papers studied the effect of RUM process parameters on machining performance and removal mechanisms for drilling of circular holes. In industries such as aerospace, the production of advanced turbine components requires machining of complex 3D features using milling strategies. The objective of this paper will be to present a new physical model based on rotary ultrasonic milling which will help provide a better scientific understanding of the process. This will be accomplished by first modeling the macro kinematics between the tool and material followed by the modeling of micro kinematics between the individual diamond grains and the material. In addition, a force model for predicting machining process forces will also be introduced and validated based on a set of experiments. The physical models will help determine the relationships between input parameters, cutting parameters, and process output parameters for rotary ultrasonic milling.     

Relationship between subsurface damage and surface roughness of glass BK7 in rotary ultrasonic machining and conventional grinding processes

Subsurface damage (SSD) induced during the abrasive machining process considerably influences the technological application of the optical components. However, to date, there is no rapid and effective method to inspect the depth of SSD. For the purpose of precise and nondestructive evaluation of the SSD depth generated in rotary ultrasonic machining (RUM) and conventional grinding (CG) processes, a theoretical model, ground on indentation fracture mechanics of brittle material, was proposed by analyzing the correlation between the median and lateral crack systems aroused by a sharp indenter. It was found that the SSD depth was nonlinear monotone increasing with square of surface roughness (SR), namely, SSD?=?χSR²?+?l. Utilizing this model, the SSD depth could be quickly and precisely predicted through the SR (p–v value.) of the machined surface, geometrical features of the abrasive, and the material mechanical properties. To validate the feasibility of this method, both RUM and CG tests were conducted on the BK7 glass specimens with a Sauer Ultrasonic 20. Subsequently, the SSD of these specimens was exposed with the polishing–etching technique. The measurement results of SSD depth were consistent with the prediction values of this model, which reflected the feasibility of using this model to rapidly and accurately predict the SSD depth.     

ROTARY ULTRASONIC MACHINING OF CARBON FIBER-REINFORCED POLYMER: FEASIBILITY STUDY

Carbon fiber-reinforced polymer (CFRP) has been widely used in aircraft components, automotive parts, and sporting goods. Hole machining is the most frequently employed operation of secondary machining for fiber-reinforced composites. However, challenges (delamination, splintering, burr, short tool life, low machining precision, and low surface quality) still remain for their widespread applications. Rotary ultrasonic machining (RUM) is a non-conventional machining process that has been used to drill holes in composite materials. However, it has not been used to drill this type of CFRP. In this article, RUM is introduced into drilling holes in this type of CFRP for the first time. The feasibility to machine carbon fiber-reinforced epoxy using RUM is investigated experimentally. Chips, edge chipping, surface roughness, tool wear, and thrust force were measured. Effects of RUM process variables (rotation speed, vibration amplitude, and feedrate) on thrust force and surface roughness were studied. Results showed that RUM could be used to drill holes in CFRP with high productivity and low tool wear. A better surface was produced by higher rotation speed and lower feed rate.     

Experimental investigation of tool wear and machining rate in rotary ultrasonic machining of nickel alloy

Nickel alloys possess the excellent potential at high temperature and resistance to oxidation/corrosion owing to its high nickel content. These materials necessitate non-traditional machining methods. The rotary ultrasonic machining (RUM) process comes into existence as a superior alternative to the conventional machining of nickel alloys. The processing of these alloys using RUM needs attention. This article details the multi-response optimization in RUM of nickel alloy using the desirability concept. The present work is carried out with two shapes of the tool: (i) Plain tool and (ii) lateral slotted tool. During RUM, the process parameters—power rating tool rotation, abrasive diamond grit size and feed rate are varied. Compared with the plain tool, the lateral slotted tool shows the more efficient machining rate (MR) with less tool wear (TW). The micro-graphs disclose the mechanism of MR and TW during RUM.     

Cutting forces,tool wear and surface finish in high speed diamond machining

We have investigated the cutting forces, the tool wear and the surface finish obtained in high speed diamond turning and milling of OFHC copper, brass CuZn39Pb3, aluminum AlMg5, and electroless nickel. In face turning experiments with constant material removal rate the cutting forces were recorded as a function of cutting speed between v_c = 150 m/min and 4500 m/min revealing a transition to adiabatic shearing which is supported by FEM simulations of the cutting process. Fly-cutting experiments carried out at low (v_c = 380 m/min) and at high cutting speed (v_c = 3800 m/min) showed that the rate of abrasive wear of the cutting edge is significantly higher at ordinary cutting speed than at high cutting speed in contrast to the experience made in conventional machining. Furthermore, it was found that the rate of chemically induced tool wear in diamond milling of steel is decreasing with decreasing tool engagement time per revolution. High speed diamond machining may also yield an improved surface roughness which was confirmed by comparing the step heights at grain boundaries obtained in diamond milling of OFHC copper and brass CuZn39Pb3 at low (v_c = 100 m/min) and high cutting speed (v_c = 2000 m/min). Thus, high speed diamond machining offers several advantages, let alone a major reduction of machining time.     

基于超声波激振强化的软性磨粒流光整加工模拟与试验研究

为了提高软性磨粒流加工过程中的湍流强度分布均匀性与材料去除率,提出一种基于超声波激振湍流强化的软性磨粒流光整加工方法。在磨粒流约束流道内引入超声激励,利用超声波的空化效应控制流道内的流体流态。建立考虑液固及声场耦合的磨粒流加工动力学模型,对其加工过程中的流场特性进行了模拟研究,并搭建超声强化磨粒流加工试验平台进行验证。数值仿真结果表明,非定常流场可获得更为均匀的速度矢量和湍动能分布,超声波激振引起空化效应能够有效地增强软性磨粒流的湍流强度和避免加工死角的出现,同时揭示湍流增强导致磨粒流动轨迹复杂多变是加载超声波激振抑制磨粒流的过加工和粗糙度值翘尾现象形成的原因。加工试验表明,该方法可减小加工时间约6 h,能够得到更为均匀的表面质量。     

Chipping minimization in drilling ceramic materials with rotary ultrasonic machining

Ultrasonic machining (USM) has been considered as a new cutting technology that does not rely on the conductance of the workpiece. USM presents no heating or electrochemical effects, with low surface damage and small residual stresses on workpiece material, such as glass, ceramics, and others; therefore, it is used to drill microholes in brittle materials. However, this process is very slow and tool wear dependent, so the entire process has low efficiency. Therefore, to increase microhole drilling productivity or hole quality, rotary ultrasonic machining (RUM) is considered as a strong alternative to USM. RUM, which presents ultrasonic axial vibration with tool rotation, is an effective solution for improving cutting speed, precision, tool wear, and other machining responses beyond those of the USM. This study aims to reduce the microchipping or cracking at the exit of the hole, which inevitably occurs when brittle materials are drilled, with consideration of tool wear. To this end, response surface analysis and desirability functions are used for experimental optimization. The experimental results showed that the proposed RUM scheme is suitable for microhole drilling.     

Wear reducing effects and temperature dependence of tribolayer formation in harsh environment

Certain materials show a tribolayer formation especially at enhanced temperatures in abrasive environment, building a wear protection layer with the abrasive on the surface. Three materials with different microstructures were tested in three-body abrasive and impact/abrasive environments at temperatures up to 700 °C to investigate tribolayer formation. Optical and electron microscopical methods were used for wear qualification. Furthermore, hot hardness tests were performed up to 700 °C to investigate the influence of hardness drop on tribolayer formation.It was shown that no significant tribolayer formation occurs on grey cast iron, whereas other materials form tribolayers. Generally, tribolayer formation increases with increasing testing temperature, especially for austenitic and ferritic materials. This entails a self-protecting effect and thus superior wear resistance in abrasive environment.     

Erosive smoothing of abrasive slurry-jet micro-machined channels in glass,PMMA, and sintered ceramics: Experiments and roughness model

Abrasive slurry jet micro-machining (ASJM) was used to machine channels in glass, PMMA, zirconium tin titanate, and aluminum nitride. The channel roughness was measured as a function of the ASJM process parameters particle size, dose, impact velocity, and impact angle. The steady-state roughness of the channels was reached relatively quickly for typical ASJM abrasive flow rates. The roughness of channels having depth-to-width aspect ratios up to about 0.25 could be reduced by approximately 35% compared to the roughest channel by decreasing particle impact velocity and angle. However, machining at such conditions reduced the specific erosion rate by 64% on average. It was therefore quicker to post-blast reference channels (225 nm average root mean square (R_rms) roughness) using process parameters selected for peak removal. It was also found that the roughness of reference channels could be reduced by about 78% by post-blasting using 3 μm diameter silicon carbide particles at 15° jet incidence. The smoothest post-blasted channels had an R_rms roughness of about 23 nm in glass, PMMA, and zirconium tin titanate, and 170 nm in aluminum nitride. Computational fluid dynamics was used to predict the particle impact conditions that were used in a model to predict the steady-state roughness due to ductile erosion with an average error of 12%.     

Research on ECM process of micro holes with internal features

Micro holes with internal features are widely used as spray holes and cooling holes nowadays, which are usually required to be with high aspect ratio and shape accuracy, as well as good surface quality. An electrochemical machining (ECM) process is presented to machine these micro holes with diameter <200 μm. A quantitative relation between micro-hole diameter and machining parameters including voltage, duty ratio and feedrate is obtained through orthogonal experiments. According to the designed shape of internal features, change rules of machining parameters for varied diameters in different depth are obtained, and then micro holes with internal features are shaped precisely. Taking reverse tapered hole as an example, ECM experiments by varying parameters of voltage, duty ratio and feedrate (called varying voltage machining, varying duty ratio machining and varying feedrate machining, respectively) are carried out. Micro holes with inlet diameter of 178 μm and taper angle of 1.05° are shaped on a 1.0 mm-thick workpiece of 18CrNi8. The deviation of inlet is <3 μm and the taper-angle error is <0.1° in varying voltage machining. The corresponding dimensional accuracy of taper angle is improved by 51% than that of varying duty ratio machining under the same efficiency. The machining efficiency of varying voltage machining is increased by 36% compared to the efficiency in varying feedrate machining. In addition, the micro holes with complex features of funnel shape and bamboo shape are machined.     

Experimental studies of the cutting force and surface morphology of explosively clad Ti–steel plates

The present work pertains to the study of clad material such as titanium plated steel in drilling process. The study was conducted for two types of indexable insert drills with different configuration of the tool coatings (TiAlN/AlTiN + TiN and TiAlN/TiN), the same geometry of insert and fixed machining conditions. Drilling process was assessed by the analysis of thrust force, torque and signal fluctuations of PSD function. In this context, surface morphology of the drilled holes and contact area was analysed. It has been observed that the use of the PSD function allows assessment of the drilling process in different layers of clad materials. Also was found that the parameters of the surface morphology are dependent upon the type of layers of the clad and the type of drill. Furthermore the reduction in torque results in obtaining smaller values of surface roughness parameter especially in the area of volume parameters of the bearing area curve.