水基纳米流体在铜丝平板热管中的应用

对使用三种水基纳米流体作为工质的铜丝平板热管的传热特性进行了实验研究.使用的纳米流体分别是平均粒径20 nm的Cu纳米颗粒、平均粒径50 nm的Cu纳米颗粒和平均粒径50 nm的CuO纳米颗粒的水基悬浮液(简称水基20 nm Cu、50 nm Cu、50 nm CuO纳米流体),着重分析了纳米流体种类,纳米颗粒质量分数、运行温度或工作压力对热管传热特性的影响.研究结果表明,使用纳米流体作为工质可以显著提高热管的传热特性;在不同运行温度条件下,不同的纳米流体均在质量分数1.0％时具有最佳传热效果;纳米流体是一种适用于铜丝平板热管的新型工质.     

An investigation of the thermal performance of cylindrical heat pipes using nanofluids

In this work, a two-dimensional analysis is used to study the thermal performance of a cylindrical heat pipe utilizing nanofluids. Three of the most common nanoparticles, namely Al₂O₃, CuO, and TiO₂ are considered as the working fluid. A substantial change in the heat pipe thermal resistance, temperature distribution, and maximum capillary heat transfer of the heat pipe is observed when using a nanofluid. The nanoparticles within the liquid enhance the thermal performance of the heat pipe by reducing the thermal resistance while enhancing the maximum heat load it can carry. The existence of an optimum mass concentration for nanoparticles in maximizing the heat transfer limit is established. The effect of particle size on the thermal performance of the heat pipe is also investigated. It is found that smaller particles have a more pronounced effect on the temperature gradient along the heat pipe.     

Comparative study of the effect of hybrid nanoparticle on the thermal performance of cylindrical screen mesh heat pipe

The thermal performance of a cylindrical screen mesh heat pipe with hybrid nanofluid was experimentally investigated. The hybrid nanofluid was prepared by mixing Al2O3 and CuO nanoparticles with deionised water. The heat pipe was fabricated with straight copper tube of dimensions 300 mm length, 12.5 mm outer diameter and 1 mm thickness. The wick structure in the heat pipe was created by a three layer copper screen mesh of 100 mesh size. The heat input to the heat pipe was varied from 50 W to 250 W in five equal steps. The heat pipe was tested with three hybrid nanofluids made with combinations of Al2O3 and CuO nanoparticle in DI water (Al2O3 75%–CuO 25%, Al2O3 50%–CuO 50% and Al2O3 25%–CuO 75%). The tested hybrid nanofluids were made with 0.1% volume concentration of Al2O3 and CuO nanoparticle combination in deionised water. The results of the investigation showed that for the maximum heat load of 250 W considered in this work, the thermal resistance of the hybrid nanofluid with combination, Al2O3 25%–CuO 75%, showed 44.25% reduction compared to deionised water. The reduction in thermal resistance is due to the formation of porous coating on the wick surface which increases the wettability and surface roughness thereby creating more nucleation sites as seen in the SEM images. From the experimental investigation, it was observed that hybrid nanofluids are alternative to the conventional working fluids in heat pipes for electronic cooling applications.     

Thermal Performance Improvement of Tractor Radiator Using CuO/Water Nanofluid

This research work discusses the heat transfer improvement in a tractor radiator with nanosized particles of CuO with water as base fluid. The nano materials and its suspension in fluids as particles have been the subject of intensive study worldwide recently since pioneering researchers recently discovered the anomalous thermal behavior of these fluids. The engine cooling in heavy vehicles is an important factor for their performance in the intended application. Here, the tractor engine radiator cooling is enhanced by the nanofluid mechanism of heat transfer for its improved performance in agricultural work. Through the improvement of tractor engine cooling through the radiator a greater area can be ploughed and cultivated within a short time span. Heat transfer in automobiles is achieved through radiators. In this research work an experimental and numerical investigation for the improved heat transfer characteristics of a radiator using CuO/water nanofluid for 0.025 and 0.05% volume fraction is done with an inlet temp of 50 °C to 60 °C under the turbulent flow regime (8000 ≤ Re ≤ 25000). The overall heat transfer coefficient decreases with an increase in nanofluid inlet temperature of 50 °C to 60°C. The experimental results of the heat transfer using the CuO nanofluid is compared with the numerical values. The results in this work suggest that the best heat transfer enhancement can be obtained compared with the base fluid by using a system with CuO/ water nanofluid‐cooled radiators.     

Thermal performance of inclined grooved heat pipes using nanofluids

An experimental study was performed to investigate the thermal performance of an inclined miniature grooved heat pipe using water-based CuO nanofluid as the working fluid. This study focused mainly on the effects of the inclination angle and the operating pressure on the heat transfer of the heat pipe using the nanofluid with the mass concentration of CuO nanoparticles of 1.0 wt%. The experiment was performed at three steady sub-atmospheric pressures. Experimental results show that the inclination angle has a strong effect on the heat transfer performance of heat pipes using both water and the nanofluid. The inclination angle of 45° corresponds to the best thermal performance for heat pipes using both water and the nanofluid. The present investigation indicates that the thermal performance of an inclined miniature grooved heat pipe can be strengthened by using CuO nanofluid.     

Oil fouling in double‐pipe heat exchanger under liquid‐liquid dispersion and the influence of copper oxide nanofluid

Dispersions of oil in water are encountered in a variety of industrial processes leading to a reduction in the performance of the heat exchangers when thermally treating such two phase fluids. This reduction is mainly due to changes in the thermal and hydrodynamical behavior of the two phase fluid. In the present work, an experimental investigation was performed to study the effects of light oil fouling on the heat transfer coefficient in a double‐pipe heat exchanger under turbulent flow conditions. The effects of different operating conditions on the fouling rate were investigated including: hot fluid Reynolds number (the dispersion), cold fluid Reynolds number, and time. The oil fouling rate was analyzed by determining the growth of fouling resistance with time and through pressure drop measurements. The influence of copper oxide (CuO) nanofluid on the fouling rate in the dispersion was also determined. It was found that the presence of dispersed oil causes a reduction in heat transfer coefficient by percentages depending on the Reynolds number of both cold and hot fluids and the concentration of oil. In addition, the time history of fouling resistance exhibited different trends with the flow rates of both fluids and its trend was influenced appreciably by the presence of CuO nanofluid.     

Comparative analysis of nanofluid‐based Organic Rankine Cycle through thermoeconomic optimization

The present work focused on the comparative analysis of organic Rankine cycle (ORC) operated with nanoparticles. The effect of CuO and Al₂O ₃ nanoparticles synthesized with water and circulated within heat exchangers are examined. Thermal efficiency and levelized energy cost (LEC) of the nanofluid based ORC are evaluated simultaneously in the present work. The optimization problem of ORC is formed and solved using heat transfer search algorithm. Operating parameters of the nanofluid based ORC such as pinch point temperature difference of heat exchangers, evaporation pressure, the mass flow rate of refrigerant, and concentration of nanoparticles are investigated in the optimization study. Further, the effect of turbine ratio, heat source temperature, and mass flow rate of heat source fluid on CuO and Al ₂O ₃ based ORC is explored and discussed. It was observed that a total variation of 35.2% was obtained at the cost of 3.5% variation in LEC between extreme design points. The maximum thermal efficiency of 19.3% and 19.32% can be obtained with CuO and Al ₂O ₃ with 2.616 and 2.62 $/kWh, respectively. Comparative results reveal that CuO based ORC shows dominance in terms of economic performance over Al ₂O ₃ based ORC for any given value of the thermal efficiency.     

Thermal performance of U-shaped serpentine microchannel heat sink using various metal oxide nanofluids

This study aims to evaluate the thermal performance and friction factor characteristics of the U-shaped serpentine microchannel heat sink using three different nanofluids. Two distinct nanoparticles, namely Al₂O₃ (alumina) and CuO (copper oxide), were used for the preparation of nanofluids using water and ethylene glycol (EG) as base fluids. Three nanofluids, namely nanofluid I (Al₂O₃ + water), nanofluid II (CuO + water), and nanofluid III (CuO + EG), have been prepared. The results showed that the thermal conductivity of nanofluids was increased for all concentrations (from 0.01 to 0.3%), compared with base fluids. The theoretical values derived from the relationship between the Darcy friction factor showed a clear understanding of the fully developed laminar flow. Thermal resistance for nanofluid III was lower than other nanofluids, resulting in a higher cooling efficiency. The nanofluid mechanism and the geometry of the U-shaped serpentine heat sink have led to the improvement in the thermal performance of electronic cooling systems.     

A Feasibility Study About Using SiO2 Nanofluid Screen Mesh Wick Heat Pipe for Cooling of High-Power LEDs

Effective and timely heat removal from high-power light-emitting diodes (LEDs) is crucial to their performance and lifetime. The strategy of using a screen mesh wick heat pipe with SiO₂ nanofluid as the working fluid for LED heat dissipation is comprehensively evaluated. An experimental system is set up to study the heat transfer performance of the heat pipe. The obtained experimental results give optimal conditions/parameters for the heat pipe: 60% charging ratio, 30° incline angle, and 1wt% concentration of the nanofluid. Compared with a heat pipe using the secondary distilled water as the working fluid, the thermal resistance of the heat pipe using the SiO₂ nanofluid as the working fluid is generally reduced by around 35–40% for the investigated heat load range of 1–60 W. Based on an equivalent heat conductivity of the SiO₂ nanofluid heat pipe derived from the experimental results, an Icepak modeling effort for the cooling system of a 60-W LED lamp is then expended. The numerical results show that the temperature of the LED lamp remains low and quite uniform across the LED chip region, indicating the technical feasibility of using this class of heat pipes for cooling of high-power LEDs.     

Experimental investigation of Al2O3–MgO hot hybrid nanofluid in a plate heat exchanger

Exergy–energy analysis of the plate heat exchanger is experimentally performed with different Al₂O₃–MgO hybrid nanofluid (HyNf) as a hot fluid. There were six combinations of fluids, namely, deionized (DI) water, ethylene glycol–DI water brine (1:9 volume ratio), propylene glycol–DI water brine (1:9 volume ratio), base fluids and their respective Al₂O₃–MgO (4:1 particle volume ratio) HyNfs of 0.1% total volume concentration. The effects of different flow rates and hot inlet temperatures on the heat transfer rate, heat transfer coefficient, pump work, irreversibility, and performance index (PI) are investigated. It is witnessed that the heat transfer rate, heat transfer coefficient, pump work, and irreversibility enhances with the flow rate and nanoparticle suspension. While the PI declines with a rise in the flow rate, the heat transfer rate, heat transfer coefficient, PI, and irreversibility rise up maximum for MgO–alumina (1:4) DI water HyNf upto 11.8%, 31.7%, 11.1%, and 4.05%, respectively. The pump work enhances upto 1.6% for MgO–alumina (1:4)/EG–DI water (1:9) HyNf.     

Single-phase heat transfer of CuO/water nanofluids in micro-fin tube equipped with dual twisted-tapes

The combined effects of nanofluids, dual twisted-tapes (DTs) and a micro-fin tube (MF) on the heat transfer rate, friction factor and thermal performance factor characteristics have been investigated. Nanofluids consisting of CuO and water at CuO concentrations between 0.3% and 1.0% by volume, were utilized as working fluids in the MF equipped with DTs, for Reynolds number between 5650 and 17,000. The experiments using the MF alone as well as the MF equipped with a single twisted tape (ST), were also conducted for comparison. The experimental results revealed that the heat transfer rate increased with increasing nanofluid concentration. At similar operating conditions, the micro-fin tube equipped with dual twisted-tapes (MF-DTs) consistently gave superior thermal performance factor to the one equipped with a single twisted-tape (MF-ST) as well as the micro-fin tube alone (MF). For all cases, thermal performance factors were apparently above unity. This indicates the beneficial effect for the energy saving by the uses of the combined techniques.     

Effect of nanofluids on the thermal performance of a flat micro heat pipe with a rectangular grooved wick

In this paper, the effect of water-based Al₂O₃ nanofluids as working fluid on the thermal performance of a flat micro-heat pipe with a rectangular grooved wick is investigated. For the purpose, the axial variations of the wall temperature, the evaporation and condensation rates are considered by solving the one-dimensional conduction equation for the wall and the augmented Young–Laplace equation for the phase change process. In particular, the thermophysical properties of nanofluids as well as the surface characteristics formed by nanoparticles such as a thin porous coating are considered. From the comparison of the thermal performance using both DI water and nanofluids, it is found that the thin porous coating layer formed by nanoparticles suspended in nanofluids is a key effect of the heat transfer enhancement for the heat pipe using nanofluids. Also, the effects of the volume fraction and the size of nanoparticles on the thermal performance are studied. The results shows the feasibility of enhancing the thermal performance up to 100% although water-based Al₂O₃ nanofluids with the concentration less than 1.0% is used as working fluid. Finally, it is shown that the thermal resistance of the nanofluid heat pipe tends to decrease with increasing the nanoparticle size, which corresponds to the previous experimental results.     

Numerical Modeling of Fluid Flow and Thermal Behavior of Different Nanofluids on a Rotating Disk

The thermal and velocity profiles of various nanofluid systems on a rotating disk are simulated. Finite difference method, the orthogonal collocation method, and the differential quadrature method (DQM) of numerical approaches are used to solve the governing equations and are compared to determine the faster and more accurate solution procedure. Five nanoparticles Al, Al₂O₃, Cu, CuO, and TiO₂ solved in three base fluids water, ethylene glycol, and engine oil are considered to be used on the disk at different volume fractions. A new general algorithm is presented for solving equations of a rotating‐disk problem quickly and accurately and it is found that the DQM method is the best approach for this numerical simulation. Heat transfer performance of a rotating disk would be much better enhanced with water based Al nanofluid. A wide range of results for different base–fluid combinations with nanoparticles is presented with untransformed 3D results and effects of the variation of different parameters provides comprehensive insight and prevents inaccurate deductions.     

Effect of Serpentine Grooves on Heat Transfer Characteristics of Microchannel Heat Sink with Different Nanofluids

An experimental and numerical investigation of the thermal performance of three different nanofluids ethylene glycol‐based CuO, water‐based CuO, and Al₂O₃ is done in a serpentine‐shaped micorchannel heat sink. The microchannels considered ranged from 810 μm to 890 μm in hydraulic diameter and were made of copper material. The experiments were conducted with the Reynolds number ranging from approximately 100 to 1300. The forced convective heat transfer coefficient of nanofluids shows that there is an improved heat transfer rate compared to base fluids water and ethylene glycol. The experimental results also confirm that there is an earlier transition from laminar to turbulent flow in microchannels. The results prove that as the hydraulic diameter decreases there is increased pressure drop and the heat transfer coefficient increases for both the base fluids and nanofluids. The flow characteristics are discussed based on the pressure drop. While investigating the heat transfer coefficient of the three different nanofluids the nanofluid CuO/EG has the highest heat transfer coefficient as a result of the material's property. This research also will encourage young researchers to work on nanofluids of varying nanoparticle size and concentration to discover new results.     

Numerical Simulation of the Thermal Performance of a Nanofluid-Filled Heat Pipe

Improving the working fluid transport properties is a way to enhance the thermal performance of heat transfer equipment. In this research work, a two-dimensional numerical simulation is used to investigate the thermal performance of a nanofluid-filled cylindrical heat pipe. The considered nanofluid is pure water as the base fluid with dispersed Al₂O₃ nanoparticles. Effects of particle volume fractions, particle diameters, various heat inputs, and wick structures on thermal performance of the heat pipe are investigated and the results are compared with that of the pure water. A comparison is made for the first time between the results of a simulation by considering fluid flow in the liquid-wick region and treating this region as pure conduction. The results show the heat pipe thermal performance enhancement and a decrease in thermal resistance for about 31% when 5% particle volume fraction with a particle diameter of 10 nm is used. Also, an insignificant effect of heat input on thermal resistance and variation of pressure distribution in the presence of nanoparticles are observed.     

Exploring the heat transfer performance of nanofluid as a coolant for power battery pack

Nanofluids with high thermal conductivity coefficient are introduced to the thermal management system of power battery packs for electric vehicles and hybrid electric vehicles. Two typical cooling structures of cylindrical and square battery packs are described, and their flow models are established. By similarity transformations, the nonlinear system of partial differential equations is reduced and then solved numerically by the shooting method. The heat transfer properties of three types of nanofluids, that is, CuO‐EG, Al₂O₃‐EG, TiO₂‐EG, are analyzed in detail. It is found that CuO‐EG nanofluid is the best coolant for the cylindrical battery pack, whereas Al₂O₃‐EG nanofluid is the best choice for square battery pack cooling.     

Performance analysis of hybrid/single nanofluids on augmentation of heat transport in lid-driven undulated cavity

This numerical study reveals the heat transfer performance of hybrid/single nanofluids inside a lid-driven sinusoidal trapezoidal-shaped enclosure. The right and left inclined surfaces of the trapezium have been considered as insulated, whereas the bottom sinusoidal wavy and the flat top surfaces of the enclosure as hot and cold, respectively. The governing partial differential equations of fluid's velocity and temperature have been resolved by applying the finite element method. The implications of Prandtl number (4.2-6.2), Richardson number (0.1-10.0), undulation number (0-3), nanoparticles volume fraction (0%-3%), and nanofluid/base fluid (water, water–copper (Cu), water–Cu–carbon nanotube, water–Cu–copper oxide (CuO), water–Cu–TiO₂, and water–Cu–Al₂O₃) on the velocity and temperature profiles have been studied. Simulated findings have been represented by means of streamlines, isothermal lines, and average Nusselt number of above-mentioned hybrid nanofluids for varying the governing parameters. The comparison of heat transfer rates using hybrid nanofluids and pure water has been also shown. The heat transfer rate is increased about 15% for varying Richardson number from 0.1 to 10.0. Blending of two nanoparticles suspension in base fluid has a higher heat transfer rate—approximately 5% than a mononanoparticle. Moreover, a higher average Nusselt number is obtained by 14.7% using the wavy surface than the flat surface of the enclosure. Thus, this study showed that applying hybrid nanofluid may be beneficial to obtain expected thermal performance.     

Thermal performance of inclined screen mesh heat pipes using silver nanofluids

This study presents the effect of silver nanofluid on thermal performance of inclined screen mesh heat pipe in cooling applications. Four cylindrical copper heat pipes containing two layers of screen mesh were fabricated and tested with distilled water and water based silver nanofluids with mass concentrations of 0.25%, 0.5% and 0.75% as working fluids. The experiments were performed at four inclination angles of 0°, 30°, 6° and 90°. The main focus of this study is to investigate inclined heat pipe performance with nanofluid. Experimental results indicate that the thermal performance of heat pipes was improved with nanofluids compared to water and thermal resistance of the heat pipes decreased with the increase of nanoparticle concentration. Moreover, the thermal performance of the heat pipes at inclination angle of 60° is found to be higher than other tested inclination angles, which shows the effect of gravity on heat pipe performance.     

Thermal Performance Enhancement of L-Shaped Microgrooved Heat Pipe Containing Water-Based Al2O3 Nanofluids

An experimental study was performed to investigate the thermal performance of an L-shaped grooved heat pipe with cylindrical cross section, which contained 0.5 wt% water-based Al₂O₃ nanofluid as the working fluid. The transient performance of the heat pipe and the effect of cooling water temperature on the heat transfer characteristics of the heat pipe were investigated. The outer diameter and the length of the heat pipe were 6 mm and 220 mm, respectively. Experimental results revealed that the temperature of the cooling water has a significant effect on the thermal resistance of the heat pipe containing nanofluids as its working fluid. By increasing the cooling water temperature from 5°C to 27.5°C, the thermal resistance decreases by approximately 40%. At the same charge volume, test results indicated an average reduction of 30% in thermal resistance of heat pipes with nanofluid as compared with heat pipe containing pure water. For transient conditions, unsteady state time for nanofluids was reduced by approximately 28%, when compared with water as the working fluid.     

Viscosity and thermal conductivity comparative study for hybrid nanofluid in binary base fluids

Thermal conductivity and viscosity analysis of Al₂O ₃/CuO (50/50) hybrid nanofluid in various mass fractions of ethylene glycol (EG) and propylene glycol (PG) binary base fluid have been investigated in the present work. Hybrid nanofluid with vol. fraction range limited to 1.5% and within the higher temperature range of 50°C to 70°C is considered for thermal conductivity and viscosity analysis. Impact on viscosity and conductivity models with various shape nanoparticles, i.e, spherical, cylindrical, brick, platelets, and blades have been discussed and were compared in EG and PG binary base fluids. Also, the analysis extends to the prediction for the stability with zeta potential and synthesis of spherical shape Al₂O₃/CuO hybrid nanofluid with X‐ray diffraction (XRD) and scanning electron microscope (SEM). The theoretical analysis revealed that thermal conductivity of Al₂O₃/CuO hybrid nanofluid in EG binary base fluid is lower compared to in PG binary base fluid. The thermal conductivity is observed to be higher in spherical and cylindrical shape nanoparticle compared to bricks, blades, and platelets shape nanoparticles. Optimum viscosity of Al₂O₃/CuO hybrid nanofluid is observed at 50%EG and 30%PG of the binary base fluid. Hybrid nanofluid in 30% of PG as binary base fluid results 16.2% higher dynamic viscosity compared to pure PG base fluid for a volume concentration of 2%. Zeta potential measurement results in the stability of spherical Al₂O₃‐CuO/ (50/50) EG/W hybrid nanofluid, and it may be considered as a heat transfer fluid.