共查询到20条相似文献,搜索用时 93 毫秒
1.
针对不同的接地形式,依据现行规范,对整个浮法玻璃厂的供电系统实施接地。对于能实施等电位联结的室内电气装置,附设变电所的车间采用TN—S接地系统,不附设变电所的车间采用TN—C—S接地系统;对于不能实施等电位联结的室外电气装置实施TT接地系统。 相似文献
2.
“接地”在ANSI/IEEE 81(1993)中定义为:一种有意或非有意的导电连接,由于这种连接,可使电路或电气设备接到大地或接到代替大地的某种较大的导电体。其目的是:(1)使连接到地的导体具有等于或近似于大地(或代替大地的导电体)的电位;(2)引导地电流流人和流出大地(或代替大地的导电体)。电气设备接地装置由接地体和... 相似文献
3.
4.
配电网接地方式选择是建设安全可靠科学电网的重要基础,接地方式主要有中性点直接接地、不接地、经消弧线圈接地和经高阻接地等,本文主要探讨分析了中性点直接接地、不接地两种接地方式的电力系统故障,并在理论分析的基础上进行比较,给出了不同电压等级下的配电网如何选择以上两种中性点接地方式的结论. 相似文献
5.
低压供配电系统中的负荷设备种类日趋多样化,各种电气设备采用共用接地有不少优点,但也存在一些问题,需要正确加以分析和对待。 相似文献
6.
《中国石油和化工标准与质量》2013,(16)
文章针对长输管道SCADA系统工程安装特点,着重结合工作实际,对长输管道SCADA系统工程中防雷接地系统进行研究与分析,同时针对防雷接地方式提出解决措施,为长输管道SCADA系统管网安全运行提供保障。 相似文献
7.
8.
9.
仪表及DCS合理、可靠的系统接地,是DCS系统非常重要的内容。为了保证DCS系统的监测控制精度和安全、可靠运行,必须对系统接地方式、接地要求、信号屏蔽、接地线截面选择、接地极布置等方面,进行认真统筹考虑。 相似文献
10.
11.
《Journal of the European Ceramic Society》2020,40(11):3766-3770
Ceramic varistors are electronic components which have a sharp change (over several orders of magnitude) of their electrical resistance at a well-defined voltage (switching voltage). Starting at low voltages, the resistance is large. But by exceeding the switching voltage the resistance drops dramatically and the component acts as a good conductor. Mounted parallel to a consumer, they are used as protection devices against over voltage loading. In the technical routine yearly billions of varistors are used to protect power lines, transformation stations, electronic devices, microelectronic systems or even LEDs.In service large temperature differences may come into existence, which cause severe mechanical stresses that even may destroy the components. The basic principles of the varistor behaviour are explained and examples of mechanical failure are discussed. 相似文献
13.
14.
针对一起10kV出线C相发生非金属接地短路产生弧光接地过电压的事故,分析事故原因,并提出防范措施. 相似文献
16.
为了透平机的安全稳定运行,增设动力UPS装置专供透平机副油泵和仪表柜在电压波动和短时停电时使用,起到了良好的保护作用,保证了生产的稳定。 相似文献
17.
阐述了在工业生产中常大量采用的高压异步电动机在运行中可能发生的故障及由此产生的危害;进而阐明,在只装有3个引出端子的一般高压电动机上配置1套通用的综合继电保护装置,对全面保护电动机的安全运行十分必要。 相似文献
18.
介绍用ZN28A型高压真空断路器替代老式GG—1A型高压开关柜内的SNl0型少油断路器的改造,探讨了有关断路器和过电压保护装置的选型、操作机构的严配、主要技术参数的调试等改造过程中遇到的一些具体问题,为相关技术改造提供一些实践经验。 相似文献
19.
根据功率半导体器件(如BJT、VDMOSFET等)的结终端结构特点,利用TCAD半导体器件仿真软件全面系统的分析了结终端高浓度扩散区结深及三种不同结终端保护结构(结终端延伸结构、浮空场限环结构及结终端刻蚀结构)参数对器件击穿特性的影响.仿真结果表明:对于终端高浓度扩散区,当表面浓度一定时,随着扩散区结深的增大,器件击穿电压呈现出先增大后减小的变化特点. PN结终端柱面结边缘区域的电场局部集中是导致器件击穿电压降低的主要因素.对于三种不同的结终端保护结构,均可有效地降低柱面结边缘电场强度,显著地改善器件的反向击穿特性.对比三种结终端保护结构,结边缘刻蚀结构对器件击穿特性的改善效果较好. 相似文献
20.
Pin Yang Carolina A. Gomez Samantha Andrews Josef D. Sorenson Ken S. Chen 《Journal of the American Ceramic Society》2021,104(7):3247-3259
The electric discharge across a varistor granule filled air gap under a fast-rising voltage pulse was investigated for surge protection applications. The effects of temperature and pressure on the arc and the electrical conduction were analyzed by the characteristic changes in voltage waveforms triggered by a fast-rising high voltage pulse. In addition to the gap size, experimental results show that competing mechanisms among arc conduction, conduction through the varistor granule network, thermionic emission from Joule heating at granule-to-granule contact points, and the magnitude of the switching voltage dictate the maximum surge protection voltage for the filled air gap. Experimental evidence indicated that accumulated degradation was created at small contact points between varistor granules by repetitive assaults from longer duration, high voltage pulses. The uniqueness of using varistor over other dielectric granules in an air gap for surge protection is identified and discussed. 相似文献