Investigation on the corrosion and oxidation resistance of Ni-Al2O3 nano-composite coatings prepared by sediment co-deposition

Ni-Al₂O₃ composite coatings were prepared by using sediment co-deposition (SCD) technique from a Watt's type electrolyte containing nano-Al₂O₃ particles. The corrosion resistance and high temperature oxidation resistance of resulting composite coatings were investigated. It was found that the incorporation of nano-Al₂O₃ particles in Ni matrix refined the Ni crystal and changed the preferential orientation of composite coatings. Meanwhile, the corrosion and oxidation resistance were improved after the incorporation of nano-Al₂O₃ particles into Ni matrix. The nano-Al₂O₃ content in deposits plays an important role for improving the corrosion and oxidation protection. The corrosion and oxidation resistance of Ni-Al₂O₃ nano-composite coatings produced via SCD technique are superior to that of CEP technique. Compared to pure Ni and Ni-Al₂O₃ composite coatings fabricated using CEP technique, the Ni-7.58 wt.% Al₂O₃ composite coating obtained by SCD technique exhibits better corrosion resistance and enhanced high temperature oxidation resistance. Moreover, the mechanism of corrosion and high temperature oxidation resistance of Ni-Al₂O₃ nano-composite coatings are discussed.     

Preparation of nanostructured Ni/Al2O3 composite coatings in high magnetic field

Ni/Al₂O₃ composite coatings were prepared by a novel method from a modified Watt's type electrolyte containing nano-Al₂O₃ particles, where a high magnetic field was imposed in the direction parallel to an electrolytic current instead of mechanical agitation. Effects of magnetic field on the content of particles, surface morphology, microhardness and wear resistance of plating layer were investigated. It was found that the high magnetic field played an important role in the formation of composite coatings. The amounts of nano-Al₂O₃ particles in the composite coating increased with increasing of magnetic flux density and reached a maximum value at 8 T, then reduced slightly. The microhardness and wear resistance of the nanocomposite coatings also enhanced with increasing of magnetic flux density as compared to that of pure Ni coating fabricated in the absence of magnetic field. That was because the co-deposited nano-Al₂O₃ particles were uniformly distributed in the Ni matrix and contributed to greatly increase the microhardness and wear resistance of the composite coatings. Moreover, the mechanism of action of high magnetic field was discussed preliminarily.     

Cr3C2-NiCr and WC-Ni thermal spray coatings as alternatives to hard chromium for erosion-corrosion resistance

Cr₃C₂-NiCr and WC-Ni coatings are widely used for wear applications at high and room temperature, respectively. Due to the high corrosion resistance of NiCr binder, Cr₃C₂-NiCr coatings are also used in corrosive environments. The application of WC-Ni coatings in corrosive media is not recommended due to the poor corrosion resistance of the (pure Ni) metallic matrix. It is well known that the addition of Cr to the metallic binder improves the corrosion properties. Erosion-corrosion performance of thermal spray coatings is widely influenced by ceramic phase composition, the size of ceramic particles and also the composition of the metallic binder. In the present work, two types of HVOF thermal spray coatings (Cr₃C₂-NiCr and WC-Ni) obtained with different spray conditions were studied and compared with conventional micro-cracked hard chromium coatings. Both as-sprayed and polished samples were tested under two erosion-corrosion conditions with different erosivity. Tungsten carbide coatings showed better performance under the most erosive condition, while chromium carbide coatings were superior under less erosive conditions. Some of the tungsten carbide coatings and hard chromium showed similar erosion-corrosion behaviour under more and less erosive conditions. The erosion-corrosion and electrochemical results showed that surface polishing improved the erosion-corrosion properties of the thermally sprayed coatings. The corrosion behaviour of the different coatings has been compared using Electrochemical Impedance Spectroscopy (EIS) and polarization curves. Total material loss due to erosion-corrosion was determined by weight loss measurements. An estimation of the corrosion contribution to the total weight loss was also given.     

Microstructure and mechanical properties of Al2O3-Cr2O3 composite coatings produced by atmospheric plasma spraying

Al₂O₃, Al₂O₃-Cr₂O₃ and Cr₂O₃ coatings were deposited by atmospheric plasma spraying. Phase composition of powders and as-sprayed coatings was determined by X-ray diffraction. Electron probe microanalyzer was employed to investigate the polished and fractured surface morphologies of the coatings. Mechanical properties including microhardness, fracture toughness and bending strength were evaluated. The results indicate that the addition of Cr₂O₃ is conducive to the stabilization of α-Al₂O₃. Compared with the pure Al₂O₃ and Cr₂O₃ coatings, Al₂O₃-Cr₂O₃ composite coatings show lower porosities and denser structures. Heterogeneous nucleation of α-Al₂O₃ occurs over the isostructural Cr₂O₃ lamellae and partial solid solution of Al₂O₃ and Cr₂O₃ might be occurring as well. Furthermore, grain refining and solid solution strengthening facilitate the mechanical property enhancement of Al₂O₃-Cr₂O₃ composite coatings.     

304不锈钢表面Ni-Al2O3复合镀层制备及性能研究

采用复合电沉积法在304奥氏体不锈钢表面制备Ni-Al₂O₃纳米镀层. 研究了Al₂O₃颗粒在复合镀层中的分布情况, 确定了镀液中颗粒的最佳加入量、最佳电流强度和最佳搅拌速度. 用扫描电镜和能谱仪、X射线衍射仪等设备鉴定镀层显微组织与组成. 结果表明, Ni-Al₂O₃纳米复合镀层均匀、致密、晶粒细小; 复合镀层结合强度、耐腐蚀性能优良, 抗高温氧化性能优于纯镍镀层.     

Thermal shock resistance of FeMnCrAl/Cr3C2-Ni9Al coatings deposited by high velocity arc spraying

FeMnCrAl/Cr₃C₂ and FeMnCrAl/Cr₃C₂-Ni9Al coatings were deposited onto low-carbon steel substrates by high velocity arc spraying. The cross-section and interface microstructures of the coatings were analyzed by optical microscopy (OM). The thermal shock resistance of the coatings was investigated. The characteristics of the coatings after the thermal cycling test were studied by OM, field emission scanning electron microscopy, and energy dispersion spectrometry. The results show that laminated structures with pores, oxide phases, and unmelted particles were found on all the prepared coatings. The FeMnCrAl/Cr₃C₂ coating with a Ni9Al interlayer registered the best thermal shock resistance, which may be attributed to the interdiffusion between the low-carbon steel substrates and the Ni9Al arc-sprayed coating that converted the mechanical bond between the substrates and the coatings to a metallurgical one.     

Ni/Cu定向结构涂层在不同浓度H2SO4中的耐蚀性能

为了研究Cu元素对Ni基合金定向结构涂层耐腐蚀性能的影响,向Ni60合金粉末中添加了5%Cu(质量分数,下同),制备了定向结构Ni60/Cu复合涂层。采用电化学试验和浸泡试验,评估了涂层在不同浓度H₂SO₄溶液中的电化学腐蚀特性和浸泡腐蚀性能,探讨了涂层在不同浓度H₂SO₄溶液中的腐蚀行为。结果表明,涂层在不同浓度H₂SO₄溶液中的腐蚀均表现为活化-钝化-过钝化的过程,电化学阻抗谱在整个时间常数内具有典型的容抗特征,H₂SO₄溶液浓度从5%增至80%时,电荷转移电阻先减小后增大,涂层的耐腐蚀性呈现先降低后升高的趋势。随着H₂SO₄溶液浓度的增加,涂层表面的腐蚀程度先加剧后逐渐减缓,且在H₂SO₄溶液浓度为40%时,腐蚀电位移至最负,腐蚀电流密度增至最大。但在H₂SO₄溶液浓度达到80...     

占空比对高频脉冲电沉积( Ni-Co) / 纳米 Al2O3复合镀层的影响

采用高频脉冲电沉积法制备(Ni-Co)/纳米Al2O3复合镀层,研究了占空比对复合镀层沉积速率、成分、形貌及表面显微硬度的影响。结果表明:随着占空比由0.3提高至0.5,复合镀层的沉积速率增加,晶粒尺寸变大,表面变粗糙,并且Co含量降低,Ni含量增加,纳米Al2O3颗粒含量变化不明显,Co含量的降低导致硬度降低。     

Preparation and characterization of nano TiO2/micron Cr2O3 composite particles

Nano-TiO₂/micro-size Cr₂O₃ composite particles were first prepared by hydrolysis of Ti(OBu)₄ in an abundant acidic aqueous solution without calcinations at room temperature. XPS analysis shows that the element C, O, Ti and Sn existed on the surfaces of the composite particles. Observation by field emission scanning electronic microscope shows TiO₂ particles of 10-15 nm covers on Cr₂O₃ powder surfaces to form nanometer/micron composite particles. UV-vis spectra show a red shift of the absorption edge and a significant increase of absorption intensity in the visible region. These results confirm that TiO₂ of anatase type can be synthesized on the surface of Cr₂O₃.     

Effect of applied current on the electrodeposited Ni-Al2O3 composite coatings

Nano-sized Al₂O₃ ceramic particles (50 nm) were co-deposited with nickel using electrodeposition technique to develop composite coatings. The coatings were produced in an aqueous nickel bath at different current densities and the research investigated the effect of applied current on microstructure and thickness of the coatings. The variation in some mechanical properties such as hardness, wear resistance, and the adhesive strength of the composite coatings is influenced by the applied current and this was also studied. The morphology of the coatings was characterized by scanning electron microscopy and energy dispersive X-ray spectroscopy. The hardness, wear resistance, and bond strength of the coatings were evaluated by Vickers micro-hardness test, pin-on-disc test, and tensile test, respectively. Results showed that the Al₂O₃ particles were uniformly distributed in the coatings, and the coatings deposited at a current density of 0.01 A/cm² was most favorable in achieving a maximum current efficiency which causes the co-deposition of a maximum amount of Al₂O₃ particles (4.3 wt.%) in the coatings. The increase in Al₂O₃ particles in the coatings increased the mechanical properties of the Ni-Al₂O₃ composite coatings by grain refining and dispersion strengthening mechanisms.     

Electroless ternary Ni-W-P alloys containing micron size Al2O3 particles

In the present investigation electroless ternary NiWP-Al₂O₃ composite coatings were prepared using an electroless nickel bath. Second phase alumina particles (1 µm) were used to codeposit in the NiWP matrix. Nanocrystalline ternary NiWP alloys and composite coatings were obtained using an alkaline citrate based bath which was operated at pH 9 and temperature at 88 ± 2 °C. Mild steel was used as a substrate material and deposition was carried out for about 4 h to get a coating thickness of 25 ± 3 µm. Metallographic cross-sections were prepared to find out the coating thickness and also the uniform distribution of the aluminum oxide particles in NiWP matrix. Surface analysis carried out on both the coatings using scanning electron microscope (SEM) showed that particle incorporation in ternary NiWP matrix has increased the nodularity of composite coatings compared to fine nodular NiWP deposits. Elemental analysis of energy dispersive X-ray (EDX) results showed that codeposited P and W elements in plain NiWP deposit were 13 and 1.2 wt.%, respectively. There was a decrease in P content from 13 to 10 wt.% with a marginal variation in the incorporated W (1.01 wt.%) due to the codeposition of aluminum oxide particles in NiWP matrix. X-ray diffraction (XRD) studies carried out on as-plated deposits showed that both the deposits are X-ray amorphous with a grain size of around 3 nm. Phase transformation studies carried out on both the coatings showed that composite coatings exhibited better thermal stability compared to plain NiWP deposits. From the XRD studies it was found that metastable phases such as NiP and Ni₅P₂ present in the composite coatings heat treated at major exothermic peak temperature. Annealed composite coatings at various temperatures revealed higher microhardness values compared to plain NiWP deposits.     

Hot corrosion behavior of detonation gun sprayed Cr3C2–NiCr coatings on Ni and Fe-based superalloys in Na2SO4–60% V2O5 environment at 900 °C

The present work investigates the hot corrosion resistance of detonation gun sprayed (D-gun) Cr₃C₂–NiCr coatings on Superni 75, Superni 718 and Superfer 800 H superalloys. The deposited coatings on these superalloy substrates exhibit nearly uniform, adherent and dense microstructure with porosity less than 0.8%. Thermogravimetry technique is used to study the high temperature hot corrosion behavior of bare and Cr₃C₂–NiCr coated superalloys in molten salt environment (Na₂SO₄–60% V₂O₅) at high temperature 900 °C for 100 cycles. The corrosion products of the detonation gun sprayed Cr₃C₂–NiCr coatings on superalloys are analyzed by using XRD, SEM, and FE-SEM/EDAX to reveal their microstructural and compositional features for elucidating the corrosion mechanisms. It is shown that the Cr₃C₂–NiCr coatings on Ni- and Fe-based superalloy substrates are found to be very effective in decreasing the corrosion rate in the given molten salt environment at 900 °C. Particularly, the coating deposited on Superfer 800 H showed a better hot corrosion protection as compared to Superni 75 and Superni 718. The coatings serve as an effective diffusion barrier to preclude the diffusion of oxygen from the environment into the substrate superalloys. It is concluded that the hot corrosion resistance of the D-gun sprayed Cr₃C₂–NiCr coating is due to the formation of desirable microstructural features such as very low porosity, uniform fine grains, and the flat splat structures in the coating.     

Degradation behaviour of ZrO2-Ni/Al gradient coatings in molten Zn

In order to improve the corrosion resistance of metallic materials in molten zinc, ZrO₂-Ni/Al gradient coatings were sprayed on the surface of the Fe-0.35-0.44 wt.% C steel. The corrosion behaviour and corrosion mechanism of the ZrO₂-Ni/Al gradient coatings in molten zinc were studied. The ZrO₂-Ni/Al gradient coatings on the surface of steels prolonged the lifetime of samples and changed the corrosion behaviour of the samples in molten zinc. The lifetime of the ZrO₂-Ni/Al gradient coatings immersed in molten zinc at 620 °C is 28 days, which is 4 times as long as that of the general ZrO₂ coatings. The ZrO₂-Ni/Al gradient coatings were corroded in molten zinc at 620 °C, which was caused by zinc atom diffusing along the crystal boundary and pores of the ZrO₂-Ni/Al gradient coatings, and reacting with Ni/Al particle in the ZrO₂-Ni/Al gradient coatings. The corrosion mechanism of the coatings in molten zinc at 620 °C was crystal boundary corrosion, pitting corrosion and reaction corrosion.     

Al_2O_3/MoS_2复合涂层的制备及摩擦磨损性能

以大气等离子喷涂工艺制备的Al_2O_3陶瓷涂层为模板,利用陶瓷涂层中存在的孔隙和微裂纹,采用水热反应在其内部原位合成具有润滑特性的MoS_2,制备出Al_2O_3/MoS_2的复合涂层。结果表明,通过水热反应在陶瓷涂层原有的微观缺陷中成功合成了MoS_2,合成的MoS_2固体粉末呈类球形状,并且这球状的粉末是由纳米片层状的MoS_2搭建组成的。摩擦试验结果表明,与纯Al_2O_3涂层相比,复合涂层中由于MoS_2润滑膜的形成,其摩擦因数和磨损率都显著降低,且载荷越大,复合涂层的摩擦性能越好。     

玻璃Cr2O3陶瓷涂层表面液态重金属润湿角的测量与表征

金属材料的腐蚀性能与其表面润湿特性有着密切的关系。采用亚音速火焰喷涂技术制备了玻璃-Cr2O3陶瓷涂层,设计了一套运行在高温环境中且密封的专用试验平台,研究经过不同保温时间后,重金属在45钢与喷有玻璃-Cr2O3陶瓷涂层的45钢表面的润湿角及相关现象的变化。结果表明:相同质量的重金属液滴在45钢表面的润湿角为18°,在玻璃-Cr2O3陶瓷涂层表面的润湿角为114°,玻璃-Cr2O3陶瓷涂层抗液态重金属润湿性能较好。固化后重金属颗粒与试样之间的接触面积及剪切强度均有所不同,304不锈钢与颗粒剪切强度为1.42MPa,而涂层与颗粒剪切强度为0.21MPa。     

Corrosion and tribological behaviors of chromium oxide coatings prepared by the glow-discharge plasma technique

In order to improve the corrosion and tribological properties of steel, chromium oxide coatings were prepared by a new combined process, namely, chromizing and plasma oxidizing treatments using double glow plasma technology under various oxygen flow rates. The composition and microstructure of the coatings were analyzed respectively by means of X-ray diffraction, scanning electron microscopy and transmission electron microscopy. The results indicated that the oxygen flow rates had a great effect on the surface structure of the prepared Cr₂O₃ coatings, and dense and smooth Cr₂O₃ coatings were prepared at the oxygen flow rate of 10 sccm. The Cr₂O₃ coatings exhibited the better corrosion resistance which was in good agreement with the results obtained by the microstructure studied. Further mechanical properties test showed that the Cr₂O₃ coatings with high hardness and elastic modulus adhered well to the steel substrates and displayed excellent wear resistance and low coefficient of friction under dry sliding wear test conditions. The wear mechanism was mostly dominated by the “soft abrasion”.     

Oxidation behavior of arc-sprayed FeMnCrAl/Cr3C2-Ni9Al coatings deposited on low-carbon steel substrates

FeMnCr/Cr₃C₂ and FeMnCrAl/Cr₃C₂ coatings, using Ni9Al arc-sprayed coating as an interlayer on low-carbon steel substrates, were deposited by high velocity arc spraying (HVAS) on the cored wires. The high temperature oxidation behavior of the arc-sprayed FeMnCrAl/Cr₃C₂-Ni9Al and FeMnCr/Cr₃C₂ coatings on the low-carbon steel substrates was studied during isothermal exposures to air at 800 °C. The surface and interface morphologies of the coatings after isothermal oxidation after 100 h were observed and characterized by optical microscopy, field emission scanning electron microscope, energy dispersion spectrum, and X-ray diffraction. The results showed that the oxidation weight gains of the coatings were significantly lower than that of the low-carbon steel substrate. Moreover, the FeMnCrAl/Cr₃C₂-Ni9Al coating registered the lowest oxidation rate. This favorable oxidation resistance is due to the Al and Cr contents of the aforementioned coating that inhibits the generation of Fe and Mn oxides. This is attributed to the interdiffusion between the substrates and the Ni9Al arc-sprayed coating, which can convert the mechanical bonding between substrates and coatings into a metallurgical one, thereby inhibiting the oxidation of interface between the low-carbon steel and the coating.     

Hot corrosion behaviour of plasma sprayed YSZ/Al2O3 dispersed NiCrAlY coatings on Inconel-718 superalloy

Oxide dispersed NiCrAlY bond coatings have been developed for enhancing thermal life cycles of thermal barrier coatings (TBCs). However, the role of dispersed oxides on high temperature corrosion, in particular hot corrosion, has not been sufficiently studied. Therefore, the present study aims to improve the understanding of the effect of YSZ dispersion on the hot corrosion behaviour of NiCrAlY bond coat. For this, NiCrAlY, NiCrAlY + 25 wt.% YSZ, NiCrAlY + 50 wt.% YSZ and NiCrAlY + 75 wt.% YSZ were deposited onto Inconel-718 using the air plasma spraying (APS) process. Hot corrosion studies were conducted at 800 °C on these coatings after covering them with a 1:1 weight ratio of Na₂SO₄ and V₂O₅ salt film. Hot corrosion kinetics were determined by measuring the weight gain of the specimens at regular intervals for a duration of 51 h. X-ray diffraction, scanning electron microscopy and energy dispersive spectroscopy techniques were used to determine the nature of phases formed, examine the surface attack and to carry out microanalysis of the hot corroded coatings respectively. The results show that YSZ dispersion causes enhanced hot corrosion of the NiCrAlY coating. Leaching of yttria leads not only to the formation of the YVO₄ phase but also the destabilization of the YSZ by hot corrosion. For the sake of comparison, the hot corrosion behaviour of a NiCrAlY + 25 wt.% Al₂O₃ coating was also examined. The study shows that the alumina dispersed NiCrAlY bond coat offers better hot corrosion resistance than the YSZ dispersed NiCrAlY bond coat, although it is also inferior compared to the plain NiCrAlY bond coat.     

Comparative study of Cr3C2-NiCr coatings obtained by HVOF and hard chromium coatings

In the present work the corrosion resistance of micro-cracked hard chromium and Cr₃C₂-NiCr (HVOF) coatings applied on a steel substrate have been compared using open-circuit potential (E_OC) measurements, electrochemical impedance spectroscopy (EIS) and polarization curves. The coatings surfaces and cross-section were characterized before and after corrosion tests using optical microscopy (OM) and scanning electron microscopy (SEM). After 18 h of immersion, the open-circuit potential values were around −0.50 and −0.25 V/(Ag∣AgCl∣KCl_sat) for hard chromium and Cr₃C₂-NiCr, respectively. The surface analysis done after 12 h of immersion showed iron on the hard chromium surface inside/near surface cracks, while iron was not detected on the Cr₃C₂-NiCr surface even after 18 h. For longer immersion time hard chromium was more degraded than thermal sprayed coating. For hard chromium coating a total resistance values between 50 and 80 kΩ cm² were measured and two well-defined time constants were observed, without significant change with the immersion time. For Cr₃C₂-NiCr coating the total impedance diminished from around 750 to 25 kΩ cm² as the immersion time increased from 17 up to 132 h and two overlapped time constants were also observed. Polarization curves recorded after 18 h of immersion showed a lower current and higher corrosion potential for Cr₃C₂-NiCr coating than other samples studied.     

Effect of α-Al2O3 coatings on the interface of Ni/SiC composites prepared by electrodeposition

This paper describes an investigation on the effect of α-Al₂O₃ coating on the interface between nickel and SiC particle. Uniform, dense and well-adhered α-Al₂O₃ coatings were obtained on the surface of SiC particles by sol–gel technology. The nickel-based composites reinforced with α-Al₂O₃-coated SiC particles (CS_p) or uncoated SiC particles (UCS_p) prepared by composite electrodeposition were heated at 600 °C to study the reactivity and the resulting interfaces. The results showed that the Ni/CS_p composites presented excellent thermal stability without interfacial reaction, while nickel silicide formed in the Ni/UCS_p composites. It indicated that high-temperature interfacial reaction between SiC particles and nickel matrix was efficiently inhibited by the α-Al₂O₃ coatings. Moreover, great differences of the local mechanical properties of interfaces were observed by the nanoindentation characterization.