0.9 V rail-to-rail constant gm CMOS amplifier input stage

Presented is a 0.9 V rail-to-rail constant g_m CMOS amplifier input stage consisting of complementary differential pairs and a g_m control circuit. The g_m control circuit eliminates the g_m dead zone, which occurs in the conventional rail-to-rail amplifier with ultra-low supply voltages. The proposed amplifier input stage has a constant g_m that varies by ±2.3% for rail-to-rail input common-mode levels. To verify the proposed amplifier design, an experimental prototype operational amplifier is also implemented using 0.35 mm standard CMOS technology.     

Low-voltage constant-gm rail-to-rail CMOS operational amplifier input stage

This paper presents a rail-to-rail constant-g_m operational amplifier input stage. The proposed circuit changes the tail current of the input differential pairs dynamically for a constant-g_m by using dummy input differential pairs. The problem which causes total g_m variation is input pairs and dummy input pairs can not take effect at the same time with the common-mode input voltage changes, because the tail current transistor of the input pairs are in triode region when the input pairs are turned off, the dummy input pairs will enter subthreshold region from cut-off region before the input pairs when common-mode voltage changes. The effect of this problem is more obviously in low supply voltage design. To solve this problem, compensate current sources is added to the tail current transistors of each dummy input differential pairs for lower g_m variation. The g_m of this Op Amp’s input stage varies around ±2%.     

Compact CMOS constant-gm rail-to-rail input stage with gm-control by an electronic zener diode

A family of compact CMOS rail-to-rail input stages with constant-g _m is presented. To attain a constant-g_m over the whole common-mode input range, an electronic zener diode is inserted between the tails of the complementary input pairs. This zener keeps the sum of the gate-source voltages of the input pairs, and therefore the g _m of the rail-to-rail input stage, constant. Two possible implementations of the zener have been realized and inserted in a rail-to-rail input stage. These input stages are implemented in two two-stage compact amplifiers. Both amplifiers have been realized in a 1 μm BiCMOS process. They have a unity-gain frequency of 2-MHz, for a capacitive load of 20 pF     

CMOS low-voltage operational amplifiers with constant-gm rail-to-rail input stage

Two 3.3-V operational amplifiers with constant-g _m rail-to-rail input stage and rail-to-rail output stage are presented. The constant transconductance (g _m ) ensures a constant unity-gain frequency within the whole commonmode input range. Two new methods to control theg _m are introduced. Both operational amplifiers use the same rail-to-rail output stage. The operational amplifiers have been integrated in a CMOS semicustom process with transistor lengths of 10µm. The common-mode input voltage swing extends beyond the positive supply rail by 400 mV and beyond the negative supply rail by 200 mV. The output voltage is able to reach within 130 mV of the supply rails. The output current of the operational amplifiers is 2 mA and the voltage gain is 85 dB. The unity-gain frquency is 165 kHz, which is mainly limited by the relatively long transistor lengths of 10µm. In another process with channel lengths of 2µm, simulation results showed that a unity-gain frequency of 4 MHz can easily be obtained.     

高增益低功耗恒跨导轨到轨CMOS运放设计

基于CSMC的0.5μmCMOS工艺,设计了一个高增益、低功耗、恒跨导轨到轨CMOS运算放大器,采用最大电流选择电路作为输入级,AB类结构作为输出级。通过cadence仿真,其输入输出均能达到轨到轨,整个电路工作在3 V电源电压下,静态功耗仅为0.206 mW,驱动10pF的容性负载时,增益高达100.4 dB,单位增益带宽约为4.2MHz,相位裕度为63°。     

A rail-to-rail input/output CMOS power amplifier

A rail-to-rail amplifier that maintains a high common-mode rejection ratio (CMRR) over the whole common-mode range and has a low harmonic distortion despite the use of relatively small output devices is discussed. The circuit, which measures only 0.3 mm² in a 3-μm technology, has a quiescent current consumption of 600 μA and a CMRR larger than 55 dB. It handles up to 4 nF, and can, with a 5-V supply, drive 3.8 V_pp into 100 Ω (0.1% total harmonic distortion at 10 kHz)     

Constant-g/sub m/ constant-slew-rate high-bandwidth low-voltage rail-to-rail CMOS input stage for VLSI cell libraries

This paper introduces a general-purpose low-voltage rail-to-rail input stage suitable for analog and mixed-signal applications. The proposed circuit provides, simultaneously, constant small-signal and large-signal behaviors over the entire input common-mode voltage range, while imposing no appreciable constraint for high-frequency operation. In addition, the accuracy of the circuit does not rely on any strict matching of the devices, unlike most of the traditional approaches based on complementary input pairs, which need to compensate for the difference in mobility between electrons and holes with the transistor aspect ratios. Also, the technique is compatible with deep submicrometer CMOS devices, where the familiar voltage-to-current square law in saturation is not completely satisfied. Based on the proposed input stage, a transconductor with rail-to-rail input common-mode range and an input/output rail-to-rail operational amplifier were developed. Both cells were designed to operate with a 3-V single supply and fabricated in standard 0.8-/spl mu/m CMOS technology. Experimental results are provided.     

A rail-to-rail input stage with constant signal behavior in 0.12 μm CMOS

This paper introduces a new fully differential low-voltage rail-to-rail input stage structure, which possesses a constant small- and large-signal behavior over the entire input common-mode range, and is suitable for low supply voltage applications in deep-submicron technologies. The proposed input stage is fabricated with two different opamp architectures in pure digital 0.12 μm CMOS technology for experimental verification. At ±0.5 V supply, the small-signal behavior variation is 5.45% across the supply rail. The large-signal behavior is constant at different input common-mode levels. The maximum current needed for the signal behavior regulation is only 90 μA.     

1 V rail-to-rail constant-gm CMOS op amp

A 1 V rail-to-rail constant-g_m CMOS operational amplifier is proposed. This study shows that keeping the sum of currents in the complementary differential pairs constant rather than controlling the tail currents produces a constant-g_m input stage operating in the weak inversion. The currents in the n-channel differential pair are regulated to keep the sum of currents in the complementary differential pairs constant using a negative feedback loop. This study also provides experimental results obtained from a 0.35 μm CMOS prototype chip.     

A compact rail-to-rail output stage for CMOS operational amplifiers

This paper presents a CMOS output stage devised for driving heavy resistive loads. An operational amplifier of this type has been fabricated in a 3 μm double-polysilicon CMOS technology. With a supply voltage of ∓5 V and load of 470 Ω, the amplifier has a ∓4.6-V output swing and features a 60 mA short-circuit output current. Although simple, the proposed configuration enables the output transistors to be driven efficiently     

New low-voltage class AB/AB CMOS op amp with rail-to-rail input/output swing

A new low-voltage CMOS Class AB/AB fully differential opamp with rail-to-rail input/output swing and supply voltage lower than two V/sub GS/ drops is presented. The scheme is based on combining floating-gate transistors and Class AB input and output stages. The op amp is characterized by low static power consumption and enhanced slew-rate. Moreover the proposed opamp does not suffer from typical reliability problems related to initial charge trapped in the floating-gate devices. Simulation and experimental results in 0.5-/spl mu/m CMOS technology verify the scheme operating with /spl plusmn/0.9-V supplies and close to rail-to-rail input and output swing.     

1.2-V CMOS op-amp with a dynamically biased output stage

A very low-voltage operational amplifier in a standard CMOS process with a 0.75 V threshold voltage is presented. It uses a novel dynamically biased output stage based on the switched-capacitor approach. Thanks to this, drive performance is greatly improved and accurate current control is also achieved. The amplifier is capable of working with a power supply as low as 1.2 V while providing a -74 dB total harmonic distortion with a 700 mV peak-to-peak output voltage into a 500 Ω and 20 pF output load. The open-loop gain and the gain-bandwidth product are higher than 90 dB and 2.2 MHz, respectively     

A rail-to-rail amplifier input stage with /spl plusmn/0.35%g/sub m/ fluctuation

A new scheme for achieving rail-to-rail input to an amplifier is introduced. Constant g/sub m/ is obtained by using tunable level shifters and a single differential pair. Feedback circuitry controls the level shifters in a manner that fixes the common-mode input of the differential pair, resulting in consistent and stable operation for rail-to-rail inputs. As the new technique avoids using complimentary input differential pairs, this method overcomes problems such as common-mode rejection ratio and gain-bandwidth product degradation that exist in many other designs. The circuit was fabricated in 0.5-/spl mu/m process. The resulting differential pair had a constant transconductance that varied by only /spl plusmn/0.35% for rail-to-rail input common-mode levels. The input common-mode range extended well past the supply levels of /spl plusmn/1.5V, resulting in only /spl plusmn/1% fluctuation in g/sub m/ for input common modes from -2 to 2 V.     

一种改进输入级结构的轨至轨运算放大器设计

基于0.18μm CMOS标准工艺设计了一种改进输入级结构的轨至轨运算放大器电路。该电路由输入级电路、共源共栅放大电路、共源输出电路及偏置电路组成。通过引入正反馈的MOS耦合对管将输入级电路改进为预放大电路,然后对其进行了详细分析,利用Cadence软件对电路进行仿真。仿真结果表明本文结构的低频直流开环增益可以达到80 dB,比相同参数下的普通结构高20 dB左右。相位裕度达到73o,共模输入电压范围满足全幅摆动,共模抑制比低频时可以达到107 dB。     

Push-pull current circuit for biasing CMOS amplifiers with rail-to-rail input common-mode range

A push-pull current circuit for biasing CMOS amplifiers with rail-to-rail input common-mode range is presented. By means of a feedback action, the circuit avoids the large magnitude deviations inherent to this type of amplifier and thus facilitates their optimisation and compensation. Simulated and experimental results obtained from a fabricated 2 mu m CMOS test chip are reported.<>     

A rail-to-rail CMOS op amp

A CMOS op amp (operational amplifier) is reported which has a rail-to-rail voltage range at its input as well as its output. An area-efficient output stage has been used. While the entire op amp occupies only 600 mil², when used as a unity-gain buffer and with ±5-V supplies, the op amp can drive a 9-V_pp/1-kHz sine wave across a 300-Ω load with -64 dB of harmonic distortion     

低压工作的轨到轨输入／输出缓冲级放大器

本文提出了一种低压工作的轨到轨输入／输出缓冲级放大器。利用电阻产生的输入共模电平移动,该放大器可以在低于传统轨到轨输入级所限制的最小电压下工作,并在整个输入共模电压范围内获得恒定的输入跨导;它的输出级由电流镜驱动,实现了轨到轨电压输出,具有较强的负载驱动能力。该放大器在CSMCO．6-μmCMOS数模混合工艺下进行了HSPICE仿真和流片测试,结果表明：当供电电压为5V,偏置电流为60uA,负载电容为10pF时,开环增益为87．7dB,功耗为579uw,单位增益带宽为3．3MHz;当该放大器作为缓冲级时,输入3VPP10kHz正弦信号,总谐波失真THD为53．2dB。     

Low-voltage high-drive CMOS current feedback op-amp

A novel CMOS current feedback op-amp is presented. The solution works using a low supply voltage and provides a wide input/output swing as well as a high current driving capability. Experimental results from a prototype implemented in a 0.35-/spl mu/m technology and powered with 1.5 V are also given. The circuit exhibits a better than 500 kHz closed-loop bandwidth and a /spl plusmn/1 mA current drive capability.     

A -90-dB THD rail-to-rail input opamp using a new local charge pumpin CMOS

This paper describes the principle and design of a CMOS rail-to-rail input operational amplifier with THD performance of -90 dB which is suited for high-quality audio systems. A new output stage has been used featuring an output suing that extends to either supply rail and is capable of driving a low ohmic load (32 Ω). The opamp, which is realized in a 0.5-μm 3.3-V digital CMOS process, uses a standard two-stage Miller configuration. The rail-to-rail input functionality is achieved with a new area-efficient on-chip charge pump which provides the local supply voltage for the input differential pair. THD levels below -90 dB have not yet been shown with existing rail-to-rail techniques. This rail-to-rail input configuration also behaves independently of the common mode level with respect to transconductance and slewing characteristics