Radio Frequency Low Noise Amplifier with Linearizing Bias Circuit

A 1.34 GHz60 MHz low noise amplifier (LNA) designed in a 0.35 m SiGe process is presented. The designed LNA exhibits a power gain of 21.46 dB and a noise figure (NF) of 1.27 dB at 1.34 GHz. The linearity is improved with an active biasing technique. The post-layout simulation shows an input referred 1-dB compression point (IP1dB) of ?11.52 dBm. Compared with the recent reported high gain LNAs, the proposed LNA has a much better linearity without degrading other performance. The LNA draws 10 mA current from a 3.3 V power supply.     

Low-power W-band CPWG InAs/AlSb HEMT low-noise amplifier

We present the development of a low-power W-band low-noise amplifier (LNA) designed in a 200-nm InAs/AlSb high electron mobility transistor (HEMT) technology fabricated on a 50-/spl mu/m GaAs substrate. A single-stage coplanar waveguide with ground (CPWG) LNA is described. The LNA exhibits a noise figure of 2.5 dB and an associated gain of 5.6 dB at 90 GHz while consuming 2.0 mW of total dc power. This is, to the best of our knowledge, the lowest reported noise figure for an InAs/AlSb HEMT LNA at 90 GHz. Biased for maximum gain, the single-stage amplifier presents 6.7-dB gain and an output 1-dB gain compression point (P1dB) of -6.7dBm at 90 GHz. The amplifier provides broad-band gain, greater than 5dB over the entire W-band.     

一种用于地面和有线接收机的宽带低噪声放大器

提出并设计了一种用于数字电视接收调谐芯片的宽带低噪声放大器.该设计采用0.35μm SiGe BiCMOS工艺,器件的主要性能为:增益等于18.8dB,增益平坦度小于1.4dB,噪声系数小于5dB,1dB压缩点为-2dBm,输入三阶交调为8dBm.在5V供电的情况下,直流功耗为120mW.     

5~22GHz平坦高增益单片低噪声放大器

使用0.25μm G aA s PHEM T工艺技术,设计和制造了性能优良的5-22 GH z两级并联反馈单片低噪声放大器。在工作频率5-22 GH z内,测得增益G≥18 dB,带内增益波动ΔG≤±0.35 dB,噪声系数N F≤3.2 dB,输入输出驻波V SW R≤1.7,最小分贝压缩点输出功率P1dB≥10.5 dBm,电流增益效率达2.77 mA/dB。测试结果验证了设计的正确性。     

5.7 GHz low-power variable-gain LNA in 0.18 /spl mu/m CMOS

A variable-gain low-noise amplifier (LNA) suitable for low-voltage and low-power operation is designed and implemented in a standard 0.18 /spl mu/m CMOS technology. With a current-reused topology, the common-source gain stages are stacked for minimum power dissipation while achieving high small-signal gain. The fully integrated 5.7 GHz LNA exhibits 16.4 dB gain, 3.5 dB noise figure and 8 dB gain tuning range with good input and output return losses. The LNA consumes 3.2 mW DC power from a supply voltage of 1 V. A gain/power quotient of 5.12 dB/mW is achieved in this work.     

Linearization technique using bipolar transistor at 5 GHz low noise amplifier

A CMOS low noise amplifier (LNA) used in wireless communication systems, such as WLAN and CDMA, must have low noise figure, high linearity, and sufficient gain. Several techniques have been proposed to improve the linearity of CMOS LNA circuits. The proposed low noise amplifier achieves high third-order input intercept point (IIP3) using multi-gated configuration technique, by using two transistors, the first is the main CMOS transistor, and the second is bipolar transistor in TSMC 0.18 m technology. Bipolar transistor is used to cancel the third-order component from MOS transistor to fulfill high linearity operation. This work is designed and fabricated in TSMC 0.18 m CMOS process. At 5 GHz, the proposed LNA achieves a measurement results as 16 dBm of IIP3, 10.5 dB of gain, 2.1 dB of noise figure, and 8 mW of power consumption.     

2～12 GHz CMOS超宽带低噪声放大器设计

提出了一种基于双反馈电流复用结构的新型CMOS超宽带(UWB)低噪声放大器(LNA),放大器工作在2～12 GHz的超宽带频段,详细分析了输入输出匹配、增益和噪声系数的性能。设计采用TSMC 0.18μm RF CMOS工艺,在1.4 V工作电压下,放大器的直流功耗约为13mW(包括缓冲级)。仿真结果表明,在2～12 GHz频带范围内,功率增益为15.6±1.4 dB,输入、输出回波损耗分别低于-10.4和-11.5 dB,噪声系数(NF)低于3 dB(最小值为1.96 dB),三阶交调点IIP3为-12 dBm,芯片版图面积约为712μm×614μm。     

Erratum to: Using Improved Product-Coded Modulation Codes to Reduce the Peak-to-Average Power Ratio in Single-Carrier Frequency Division Multiple Access Systems

A new ultra-wideband common gate low noise amplifier (LNA) for 3–6 GHz WLAN and WPAN applications is presented in which a current reused noise canceling structure utilized in the first stage not only provides a suitable noise performance, but also enhances the linearity characteristics of the LNA in a power efficient manner needed by WLAN/WPAN applications. The overall structure of the proposed LNA, consisting of three stages, namely input matching common gate stage with noise canceling, gain stage, and buffer one, is designed, laid out, and analyzed in 0.18 µm RF CMOS process. The LNA has a noise figure of 3.5–3.6 dB, a high and flat power gain of 20.27 ± 0.13 dB, and input and output losses of better than ?11 and ?14 dB, respectively, over the entire frequency band of 3–5 GHz, while these parameters are 3.5 dB, 20.75 ± 0.25 dB, ?15 and ?9 dB for the frequency band of 5–6 GHz, respectively. IIP2 and IIP3 of the proposed topology are equal to 25.9 and ?1.85 dBm, respectively, at 4 GHz frequency. The proposed LNA has 15.3 mW power dissipation from a 1.8 V supply.     

S波段雷达接收机前端低噪声放大器

采用0.35μm SiGe BiCMOS工艺设计了用于S波段雷达接收机前端电路的低噪声放大器。对于现代无线接收机来说,其动态范围和灵敏度很大程度上都取决于低噪声放大器的噪声性能和线性度。相对于CMOS工艺来说,SiGe BiCMOS工艺具有更高的截止频率、更好的噪声性能和更高的电流增益,非常适合微波集成电路的设计。该低噪声放大器采用三级放大器级联的结构以满足高达30dB的增益要求。在5V的电源电压下,满足绝对稳定条件,在3GHz-3.5GHz频段内,功率增益为34.5dB,噪声系数为1.5dB,输出1dB功率压缩点为11dBm。     

K-band low-noise amplifiers using 0.18 /spl mu/m CMOS technology

Two K-Band low-noise amplifiers (LNAs) are designed and implemented in a standard 0.18 /spl mu/m CMOS technology. The 24 GHz LNA has demonstrated a 12.86 dB gain and a 5.6 dB noise figure (NF) at 23.5 GHz. The 26 GHz LNA achieves an 8.9 dB gain at the peak gain frequency of 25.7 GHz and a 6.93 dB NF at 25 GHz. The input referred third-order intercept point (IIP3) is >+2 dBm for both LNAs with a current consumption of 30 mA from a 1.8 V power supply. To our knowledge, the LNAs show the highest operation frequencies ever reported for LNAs in a standard CMOS process.     

用于SiGe HBT LNA的新型双有源偏置电路的设计

偏置工作点是影响低噪声放大器(LNA)线性度的因素之一.为了保证LNA能够更好地对信号进行线性放大,稳定的偏置工作点对于放大器来说显得尤为重要.提出了一种新型有源偏置技术,通过同时采用两个电流源为LNA提供直流偏置,以达到稳定放大器偏置工作点的目的.基于JAZZ 0.35 μm SiGe工艺,采用该新型双有源偏置技术,设计了一款LNA.在1.8～2.2 GHz频带时,放大器的增益为22.03±0.46 dB,噪声系数小于3.7dB,2.0 GHz时的输入3阶交调点(IIP3)为5 dBm,相对于传统无源偏置的LNA提高了10 dBm.仿真验证了该新型有源偏置技术对提高LNA线性度的有效性.     

带有ESD保护,900MHz/2.4 GHz Dual-BandCMOS LNA的设计

设计了一个可以同时工作在900 MHz和2.4 GHz的双频带(Dual-Band)低噪声放大器(LNA).相对于使用并行(parallel)结构LNA的双频带解决方案,同时工作(concurrent)结构的双频带LNA更能节省面积和减少功耗.此LNA在900MHz和2.4 GHz两频带同时提供窄带增益和良好匹配.该双频带LNA使用TSMC 0.25 μm 1P5M RF CMOS工艺.工作在900MHz时,电压增益、噪声系数(Noise Figure)分别是21 dB、2.9 dB;工作在2.4 GHz时,电压增益、噪声系数分别是25dB、2.8 dB,在电源电压为2.5 V时,该LNA的功耗为12.5mW,面积为1.1mm×0.9 mm.使用新颖的静电防护(ESD)结构使得在外围PAD上的保护二极管面积仅为8 μm×8 μm时,静电防护能力可达2 kV(人体模型)     

A 0.18μm CMOS low noise amplifier using a current reuse technique for 3.1-10.6 GHz UWB receivers

A new,low complexity,ultra-wideband 3.1-10.6 GHz low noise amplifier(LNA),designed in a chartered 0.18μm RFCMOS technology,is presented.The ultra-wideband LNA consists of only two simple amplifiers with an inter-stage inductor connected.The first stage utilizing a resistive current reuse and dual inductive degeneration technique is used to attain a wideband input matching and low noise figure.A common source amplifier with an inductive peaking technique as the second stage achieves high flat gain and wide -3 dB bandwidth of the overall amplifier simultaneously.The implemented ultra-wideband LNA presents a maximum power gain of 15.6 dB,and a high reverse isolation of—45 dB,and good input/output return losses are better than -10 dB in the frequency range of 3.1-10.6 GHz.An excellent noise figure(NF) of 2.8-4.7 dB was obtained in the required band with a power dissipation of 14.1 mW under a supply voltage of 1.5 V.An input-referred third-order intercept point(IIP3) is -7.1 dBm at 6 GHz.The chip area,including testing pads,is only 0.8×0.9 mm2.     

A 0.18μm CMOS 3-5 GHz broadband flat gain low noise amplifier

A 3-5 GHz broadband flat gain differential low noise amplifier (LNA) is designed for the impulse radio uitra-wideband (IR-UWB) system. The gain-flatten technique is adopted in this UWB LNA. Serial and shunt peaking techniques are used to achieve broadband input matching and large gain-bandwidth product (GBW). Feedback networks are introduced to further extend the bandwidth and diminish the gain fluctuations. The prototype is fabricated in the SMIC 0.18 μm RF CMOS process. Measurement results show a 3-dB gain bandwidth of 2.4-5.5 GHz with a maximum power gain of 13.2 dB. The excellent gain flatness is achieved with ±0.45 dB gain fluctuations across 3-5 GHz and the minimum noise figure (NF) is 3.2 dB over 2.5-5 GHz. This circuit also shows an excellent input matching characteristic with the measured S11 below-13 dB over 2.9-5.4 GHz. The input-referred 1-dB compression point (IPldB) is -11.7 dBm at 5 GHz. The differential circuit consumes 9.6 mA current from a supply of 1.8 V.     

2.45 GHz 0.18 μm全差分CMOS低噪声放大器设计

设计了一个基于TSMC 0.18 μm CMOS工艺的2.45 GHz全差分CMOS低噪声放大器.根据电路结构特点,采用图解法对LNA进行功耗约束下的噪声优化,以选取最优的晶体管栅宽;设计了仅消耗15 μA电流的偏置电路;采用在输入级增加电容的方法,在改善输入匹配网络特性的同时,解决了栅极电感的集成问题.仿真结果表明:LNA噪声系数为1.96 dB,功率增益S_(21)超过20 dB,输入反射系数S_(11)和输出反射系数S_(22)分别小于-30 dB和-20 dB,反向功率增益S_(12)小于-30 dB,1 dB压缩点和三阶互调输入点IIP3分别达到-17.1 dBm和-2.55 dBm,整个电路在1.8 V电源下功耗为22.4 mW.     

High linearity technique for ultra-wideband low noise amplifier in 0.18 μm CMOS technology

A linearization technique for ultra-wideband low noise amplifier (UWB LNA) has been designed and fabricated in standard 0.18 μm CMOS technology. The proposed technique exploits the complementary characteristics of NMOS and PMOS to improve the linearity performance. A two-stage UWB LNA is optimized to achieve high linearity over the 3.1-10.6 GHz range. The first stage adopts inverter topology with resistive feedback to provide high linearity and wideband input matching, whereas the second stage is a cascode amplifier with series and shunt inductive peaking techniques to extend the bandwidth and achieve high gain simultaneously. The proposed UWB LNA exhibits a measured flat gain of 15 dB within the entire band, a minimum noise figure of 3.5 dB, and an IIP3 of 6.4 dBm while consuming 8 mA from a 1.8 V power supply. The total chip area is 0.39 mm², including all pads. The measured input return loss is kept below −11 dB, and the output return loss is −8 dB, from 3.1 to 10.6 GHz.     

2.1GHz CMOS低噪声放大器

采用上海华虹NEC0.35μm标准CMOS工艺进行RFCMOS窄带低噪声放大器的设计和制作。测试结果表明,在2.1GHz时,输入驻波比1.1,输出驻波比1.5,增益18dB,噪声系数2.7dB,P-1dB输出功率9dBm。     

A low-power and high-gain fully integrated CMOS LNA

In this paper, we present the design of a fully integrated CMOS low noise amplifier (LNA) with on-chip spiral inductors in 0.18 μm CMOS technology for 2.4 GHz frequency range. Using cascode configuration, lower power consumption with higher voltage and power gain are achieved. In this configuration, we managed to have a good trade off among low noise, high gain, and stability. Using common-gate (CG) configuration, we reduced the parasitic effects of C_gd and therefore alleviated the stability and linearity of the amplifier. This configuration provides more reverse isolation that is also important in LNA design. The LNA presented here offers a good noise performance. Complete simulation analysis of the circuit results in center frequency of 2.4 GHz, with 37.6 dB voltage gain, 2.3 dB noise figure (NF), 50 Ω input impedance, 450 MHz 3 dB power bandwidth, 11.2 dB power gain (S₂₁), high reverse isolation (S₁₂)<−60 dB, while dissipating 2.7 mW at 1.8 V power supply.     

Design and optimization of CMOS LNA with ESD protection for 2.4 GHz WSN application

A new optimization method of a source inductive degenerated low noise amplifier(LNA) with electrostatic discharge protection is proposed.It can achieve power-constrained simultaneous noise and input matching. An analysis of the input impedance and the noise parameters is also given.Based on the developed method,a 2.4 GHz LNA for wireless sensor network application is designed and optimized using 0.18-μm RF CMOS technology. The measured results show that the LNA achieves a noise figure of 1.59 dB,a power gain of 14.12 dB, an input 1 dB compression point of-8 dBm and an input third-order intercept point of 1 dBm.The DC current is 4 mA under a supply of 1.8 V.     

增益可调宽带CMOS低噪声放大器设计

设计了一种应用于超宽带系统中的可变增益宽带低噪声放大器。电路中采用了二阶巴特沃斯滤波器作为输入和输出匹配电路;采用了两级共源共栅结构实现电路的放大,并通过控制第二级的电流,实现了在宽频带范围内增益连续可调;采用了多栅管(MGTR),提高了电路的线性度;设计基于SMIC 0.18μm CMOS工艺。仿真结果显示,在频带3~5 GHz的范围内最高增益17 dB,增益波动小于1.8 dB,输入和输出端口反射系数分别小于-10 dB和-14 dB,噪声系数nf小于3.5 dB,当控制电压Vctrl=1.4 V时,IIP3约为2 dBm,电路功耗为16 mW。