Fabrication and Photoluminescence Characteristics of Eu3+-Doped Lu2O3 Transparent Ceramics

A novel co-precipitation process was adopted for the preparation of highly sinterable europium-doped lutetia powders using ammonium hydroxide (NH₃·H₂O) and ammonium hydrogen carbonate (NH₄HCO₃) as the mixed precipitant. The resultant powders calcined at 1000°C for 2 h showed good dispersity and excellent sinterability. Highly transparent polycrystalline lutetia ceramics with a relative density of ∼99.9% were fabricated by pressureless sintering in flowing H₂ atmosphere at 1850°C for 6 h without any additives. The average grain sizes of the transparent material were estimated to be 50–60 μm. Optical in-line transmittance in the visible wavelength region for Lu₂O₃ ceramics (1 mm in thickness) reached 80%. The luminescence and decay behavior of the obtained transparent plate and the corresponding nanophosphors were also investigated.     

Preparation and Upconversion Properties of Yb3+, Ho3+: Lu2O3 Nanocrystalline Powders

Yb³⁺, Ho³⁺: Lu₂O₃ nanocrystalline powders were synthesized by a reverse-strike co-precipitation method using NH₄HCO₃ and NH₃·H₂O as precipitators. X-ray diffraction analysis and field emission scanning electron microscopy observation showed that the phase composition of the powders was cubic and the particle size was 30–50 nm. Under the excitation of a 980 nm continuous wave diode laser, green and red emissions centered around 548 and 667 nm, respectively, were observed and the green emission dominated the upconversion spectrum. Power studies revealed that a two-photon process was involved in the upconversion emissions and the possible upconversion mechanisms were discussed.     

Ion Exchange in Alkali Layers of Potassium β -Ferrite ((1 + x)K2O · 11Fe2O3) Single Crystals

The potassium ions in potassium β-ferrite ((1 + x)K₂O ·11Fe₂O₃) crystals were exchanged with Na⁺, Rb⁺, Cs⁺, Ag⁺, NH₄⁺, and H₃O⁺ in molten nitrates or in concentrated H₂SO₄. On the other hand, spinel and hexagonal ferrites were formed by soaking the crystals in the melt of divalent salts. The crystals of K⁺, Rb⁺, and Cs⁺β-ferrites decomposed to form α-Fe₂O₃ at high temperatures of 800° to 1100°C. In addition, H₃O⁺, NH₄⁺, and Ag⁺β-ferrites decomposed to form α-Fe₂O₃ at relatively low temperatures of 350° to 650°C, in accordance with the stabilities of the inserted ions. The electrical properties of some β-ferrites were measured.     

Phase Relationships in the Si3N4–SiO2–Lu2O3 System

Phase relationships in the Si₃N₄–SiO₂–Lu₂O₃ system were investigated at 1850°C in 1 MPa N₂. Only J-phase, Lu₄Si₂O₇N₂ (monoclinic, space group P 2₁/ c , a = 0.74235(8) nm, b = 1.02649(10) nm, c = 1.06595(12) nm, and β= 109.793(6)°) exists as a lutetium silicon oxynitride phase in the Si₃N₄–SiO₂–Lu₂O₃ system. The Si₃N₄/Lu₂O₃ ratio is 1, corresponding to the M-phase composition, resulted in a mixture of Lu–J-phase, β-Si₃N₄, and a new phase of Lu₃Si₅ON₉, having orthorhombic symmetry, space group Pbcm (No. 57), with a = 0.49361(5) nm, b = 1.60622(16) nm, and c = 1.05143(11) nm. The new phase is best represented in the new Si₃N₄–LuN–Lu₂O₃ system. The phase diagram suggests that Lu₄Si₂O₇N₂ is an excellent grain-boundary phase of silicon nitride ceramics for high-temperature applications.     

Fabrication of Transparent, Sintered Sc2O3 Ceramics

We report here the fabrication of transparent Sc₂O₃ ceramics via vacuum sintering. The starting Sc₂O₃ powders are pyrolyzed from a basic sulfate precursor (Sc(OH)_2.6(SO₄)_0.2·H₂O) precipitated from scandium sulfate solution with hexamethylenetetramine as the precipitant. Thermal decomposition behavior of the precursor is studied via differential thermal analysis/thermogravimetry, Fourier transform infrared spectroscopy, X-ray diffractometry, and elemental analysis. Sinterability of the Sc₂O₃ powders is studied via dilatometry. Microstructure evolution of the ceramic during sintering is investigated via field emission scanning electron microscopy. The best calcination temperature for the precursor is 1100°C, at which the resultant Sc₂O₃ powder is ultrafine (∼85 nm), well dispersed, and almost free from residual sulfur contamination. With this reactive powder, transparent Sc₂O₃ ceramics having an average grain size of ∼9 μm and showing a visible wavelength transmittance of ∼60–62% (∼76% of that of Sc₂O₃ single crystal) have been fabricated via vacuum sintering at a relatively low temperature of 1700°C for 4 h.     

Synthesis of Transparent Nd-doped HfO2-Y2O3 Ceramics Using HIP

A Nd-doped HfO₂-Y₂O₃ ceramic having excellent transmittance was synthesized by HIPing, using high-purity powders (>99.99 wt%) of Y₂O₃, Nd₂O₃, and HfO₂. The mixed powder compacts of these powders were sintered at 1650°C for 1 h under vacuum and HIPed at 1700°C for 3 h under 196 MPa of Ar. The specimen after HIPing consisted of uniform grains measuring about 30 μm and having pore-free structure. The optical transmittance of 1 at.% Nd-doped 2.6 mol% HfO₂-Y₂O₃ ceramics ranging between visible and infrared wavelength was almost equivalent or superior to that of a Nd:Y₂O₃ single crystal grown by the Verneuil method.     

Formation of Sm2+ lons in Sol-Gel-Derived Glasses of the System Na2 O-Al2O3-SiO2

Samarium ions (Sm²⁺) incorporated into aluminosilicate glasses by a sol-gel process showed persistent spectral hole burning at room temperature. Gels of the system Na₂O-Al₂O₃SiO₂ synthesized by the hydrolysis of Si(OC₂H₅)₄, Al(OC₄H₉)₃, CH₃ COONa, and SmCl₃·6H₂O were heated in air at 500°C, then reacted with H₂ gas to form Sm²⁺ ions. Whereas Al³⁺ ions effectively dispersed the Sm³⁺ ions in the glass structure, Na⁺ ions were not effective. The Al₂O₃-SiO₂ glasses proved appropriate for reacting the Sm³⁺ ions with H₂ gas and exhibited the intense photoluminescence of Sm²⁺ ions. The reaction of Sm³⁺ ions with H₂ in the Al₂O₂-SiO₂ glasses was determined by first-order kinetics, and the activation energy equaled 95 kJ/mol. At 800°C, the maximum photoluminescence of the Sm²⁺ ions was achieved within 20 min.     

Effects of Palladium Dispersions on Gas-Sensitive Conductivity of Semiconducting Ga2O3 Thin-Film Ceramics

The gas sensitivity of Ga₂O₃ thin-film n -type conductors was investigated at temperatures of 500–1000°C. Palladium dispersions whose particle sizes are dependent on the preceding annealing processes were deposited by a wet-chemical technique onto Ga₂O₃ thin-film ceramics. The palladium clusters and their temperature-dependent growth were detected using scanning electron microscopy micrographs and X-ray photoemission spectroscopy measurements. The effect of the palladium dispersions on the gas-sensitive behavior of the Ga₂O₃ ceramics was investigated in various O₂/H₂ mixtures in the N₂ carrier gas at 700°C. The conductivity of the ceramics treated in this way was dependent on the O₂ partial pressure, as well as on the H₂ partial pressure of the surrounding gas atmosphere. The ceramic conductivity can be described as a function of the O₂:H₂ ratio, in accordance with the relation σ( p O₂/ p H₂/)^−1/3.     

Hot-Pressed Silicon Nitride with Lu2O3 Additives: Oxidation and Its Effect on Strength

The oxidation behavior and effect of oxidation on room-temperature flexural strength were investigated for hot-pressed Si₃N₄ ceramics, with 3.33 and 12.51 wt% Lu₂O₃ additives, exposed to air at 1400° and 1500°C for up to 200 h. Parabolic oxidation behavior was observed for both compositions. The oxidation products consisted of Lu₂Si₂O₇ and SiO₂. The Lu₂Si₂O₇ grew out of the surface silicate in preferred orientations. The morphology of oxidized surfaces was dependent on the amount of additive; Lu₂Si₂O₇ grains in the 3.33 wt% composition appeared partially in a needlelike type, compared with a more equiaxed type exhibited in the 12.51 wt% case. The high resistance to oxidation shown for both compositions was attributed to the extensive amounts of crystalline, refractory secondary phases formed during the sintering process. Moreover, after 200 h of oxidation at 1400° and 1500°C, the strength retention displayed by the two compositions was 93%–95% and 85%–87%, respectively. The strength decrease was associated with the formation of new defects at the interface between the oxide layer and the Si₃N₄ bulk.     

Formation, Characterization, and Hot Isostatic Pressing of Cr2O3-Doped ZrO2 (0,3 mol% Y2O3) Prepared by Hydrazine Method

In the ZrO₂-Cr₂O₃ system, metastable t -ZrO₂ solid solutions containing up to 11 mol% Cr₂O₃ crystallize at low temperatures from amorphous materials prepared by the hydrazine method. The lattice parameter c decreases linearly from 0.5149 to 0.5077 nm with increased Cr₂O₃ content, whereas the lattice parameter a is a constant value ( a = 0.5077 nm) regardless of the starting composition. At higher temperatures, transformation (decomposition) of the solid solutions proceeds in the following way: t (ss)→ t (ss) + m + Cr₂O₃→ m + Cr₂O₃. Above 11 mol% Cr₂O₃ addition, c-ZrO₂ phases are formed in the presence of Cr₂O₃. The t -ZrO₂ solid solution powders have been characterized for particle size, shape, and surface area. They consist of very fine particles (15–30 nm) showing thin platelike morphology. Dense ZrO₂(3Y)-Cr₂O₃ composite ceramics (∼99.7% of theoretical) with an average grain size of 0.3 μm have been fabricated by hot isostatic pressing for 2 h at 1400°C and 196 MPa. Their fracture toughness increases with increased Cr₂O₃ content. The highest K _Ic value of 9.5 MPa·;m^1/2 is achieved in the composite ceramics containing 10 mol% Cr₂O₃.     

Sc2O3 Nanopowders via Hydroxyl Precipitation: Effects of Sulfate Ions on Powder Properties

Hydroxyl-type Sc₂O₃ precursors have been synthesized via precipitation at 80°C with hexamethylenetetramine as the precipitant. The effects of starting salts (scandium nitrate and sulfate) on powder properties are investigated. Characterizations of the powders are achieved by elemental analysis, X-ray diffractometry (XRD), differential thermal analysis/thermogravimetry (DTA/TG), high-resolution scanning electron microscopy (HRSEM), and Brunauer-Emmett-Teller (BET) analysis. Hard-aggregated precursors (γ-ScOOH·0.6H₂O) are formed with scandium nitrate, which convert to Sc₂O₃ at temperatures ≥400°C, yielding nanocrystalline oxides of low surface area. The use of sulfate leads to a loosely agglomerated basic sulfate powder having an approximate composition of Sc(OH)_2.6(SO₄)_0.2·H₂O. The powder transforms to Sc₂O₃ via dehydroxylization and desulfurization at temperatures up to 1000°C. Well-dispersed Sc₂O₃ nanopowders (∼64.3 nm) of high purity have been obtained by calcining the basic sulfate at 1000°C for 4 h. The effects of SO₄²⁻ on powder properties are discussed.     

Mechanism of the Blue Up-Conversion in Tm3+/Nd3+-doped Calcium Aluminate Glasses

Blue up-conversion fluorescence from the Tm³⁺:¹ G ₄→³ H ₆ (480 nm) transition has been observed from calcium aluminate glass codoped with Tm³⁺/Nd³⁺. The mechanism for the up-conversion process consists of a two-photon process. An excitation beam with a wavelength of 791 nm first excites Tm³⁺ to the ³ H ₄ level, where Tm³⁺ again absorbs the 1060 nm emission from Nd³⁺:⁴ F _3/2→⁴ I _11/2 to attain the Tm³⁺:¹G₄ level. Lifetime and intensity variations with compositions suggest the presence of an efficient energy transfer from Nd³⁺ to Tm³⁺. The highest 480 nm emission intensity has been obtained from the glass with 0.1 mol% of Nd₂O₃ and 0.2 mol% of Tm₂O₃.     

Barium Neodymium Titanate Electroceramics: Phase Equilibria Studies of Ba6–3xNd8+2xTi18O54 Solid Solution

A solid-solution phase with the general formula Ba_6-3x Nd_8+2x Ti₁₈O₅₄, where 0.25(5) ≤×≤ 0.75(5), has been characterized at 1250°C; this phase has been variously described as BaNd₂Ti₄O₁₂ and BaNd₂Ti₅O₁₄ in the literature. Variation in its stoichiometry is accommodated via the cation substitution mechanism, 3Ba²⇆2Nd³⁺. The location and extent of the solid solution were demonstrated by a combination of phase diagram studies and X-ray diffraction techniques, including lattice parameter measurements and electron microscopy. A combination of techniques was employed due to the insensitivity of secondary phase detection by X-ray diffraction in this system. Using this approach, a second possible solid-solution mechanism, Ba²⁺2Nd³⁺⇆2Ti⁴⁺, is discounted.     

Energy Transfer Process for the Blue Up-Conversion in Calcium Aluminate Glasses Doped with Tm3+ and Nd3+

Excitation of Tm³⁺ to ³ H ₄ using the 791 nm pump source showed the frequency up-converted blue emission (∼480 nm) due to the Tm³⁺:¹ G ₄→³ H ₆ transition in Tm³⁺/Nd³⁺ codoped CaO·Al₂O₃ glasses. Intensity and lifetime changes with rare-earth concentrations suggested the efficient energy transfer of Tm³⁺:³ H ₄→ Nd³⁺:⁴ F _5/2 and Nd³⁺:⁴ F _3/2→ Tm³⁺:¹ G ₄. The latter transfer enabled Tm³⁺ to reach its ¹ G ₄ level, and the blue emission became possible through the ¹ G ₄→³ H ₆ transition. Quantitative analysis with rate equations proved that these two transitions were the most efficient among all the possible energy transfer routes between Tm³⁺ and Nd³⁺. Calculated up-conversion efficiency of the Tm³⁺/Nd³⁺ combination in CaO·Al₂O₃ glass was 6.6 × 10⁻³, and it was ∼4 orders of magnitude larger than those reported for other oxide glasses.     

Mechanical Property and Oxidation Behavior of Self-Reinforced Si3N4 Doped with Re2O3 (Re=Yb, Lu)

In this work, self-reinforced silicon nitrides with β-Si₃N₄ seeds doped with Re₂O₃ (Re=Yb, Lu) were investigated. Firstly, the two kinds of seeds were obtained by heating α-Si₃N₄ powder with Yb₂O₃ or Lu₂O₃, respectively. Then the self-reinforced silicon nitride ceramics were prepared by HP-sintering of α-Si₃N₄ powder, Re₂O₃ as additive, and the as-prepared seeds. Oxidation test was carried out at 1400°C in air for 100 h with thermogravimetry analysis (TGA) measurement. Mechanical properties, scanning electronic microscopy microstructures, and X-ray diffraction patterns were measured before and after oxidation. The results indicated that the introduction of the seeds doped with Re₂O₃ (Re=Yb, Lu) could obviously increase the toughness and keep the room temperature and high-temperature strength of the ceramics at high values. After oxidation, the crystalline phase in grain boundary changed and the mechanical properties decreased. TGA showed a parabolic weight gain and the oxidation mechanism was discussed.     

Sol–Gel Processed Y-PSZ Ceramics with 5 wt% Al2O3

Y-PSZ ceramics with 5 wt% Al₂O₃ were synthesized by a sol–gel route. Experimental results show that powders of metastable tetragonal zirconia with 2.7 mol% Y₂O₃ and 5 wt% Al₂O₃ can be fabricated by decomposing the dry gel powder at 500°C. Materials sintered in an air atmosphere at 1500°C for 3 have high density (5.685 g/cm³), high content of metastable tetragonal zirconia (>96%), and high fracture toughness (8.67 MPa.m^1/2). Compared with the Y-PSZ ceramics, significant toughening was achieved by adding 5 wt% Al₂O₃.     

Electroceramics from Source Materials via Molecular Intermediates: PbTiO3 from TiO2 via [Ti(catecholate)3]2-

The precursor [NH₄]₂[Ti(catecholate)₃] · 2H₂O is known to react with Ba(OH)₂· 8H₂O in an acid/base process that generates Ba[Ti(catecholate)₃] · 3H₂O, a compound which undergoes low-temperatue calcination to produce BaTiO₃ powder. Attempts to develop similar routes to PbTiO₃ have been frustrated, since lead(II) hydroxide does not exist. The amphoteric yellow PbO and the basic oxide, Pb₆O(OH)₆⁴⁺, are both insufficiently basic to react with [NH₄]₂[Ti(catecholate)₃] · 2H₂O. Based on the large sizes of both the [Ti(catecholate)₃]^2- anion and the Pb²⁺ cation, a precipitation method has been developed in which lead nitrate and [NH₄]₂[Ti(catecholate)₃] · 2H₂O are added together in an aqueous medium causing precipitation and leaving only NH₄NO₃ in solution. The lead-titanium-catecholate complex that forms in this manner undergoes low-temperature pyrolysis to produce PbTiO₃. SEM indicates a submicrometer ultimate crystallite size.     

Hot Isostatic Pressing of Reactive SnO2 Powder

Tin(IV) oxide (SnO₂) crystallizes at room temperature by adding hydrazine monohydrate ((NH₂)₂· H₂O) to a hydrochloric acid solution of tin, followed by washing and drying. Well-densified SnO₂ ceramics (99.8% of theoretical) with an average grain size of 0.9 μm have been fabricated by hot isostatic pressing for 2 h at 900°C and 196 MPa. Their Vickers hardness and bending strength are 14.4 GPa and 200 MPa, respectively. They exhibit an electrical conductivity of 2 × 10⁻³−9 × 10⁻³ S·cm⁻¹ at room temperature.     

Processing and Properties of in Situ-Reinforced α-SiAlONs Stabilized with Y2O3 and Lu2O3

α-SiAlONs with equiaxed and elongated microstructures stabilized with Y₂O₃ and Lu₂O₃ were produced by hot pressing, and the phase structure and room- and high-temperature mechanical properties were assessed. Additional liquid added to the starting composition in the form of 5 wt% rare-earth monosilicate resulted in the formation of elongated microstructures and improvements in room-temperature strength and fracture toughness. The elongated grain growth was promoted by the additional liquid phase, which crystallized to form a secondary grain-boundary phase thought to be J ' (Re₄Si_{2– x} Al _x O_{7+ x} N_{2– x} ). For the equiaxed and the elongated samples, those sintered with Lu₂O₃ showed higher hardness than the comparable Y₂O₃-sintered materials, and, at elevated temperature, the strength retention of the elongated Lu₂O₃ SiAlON was much higher than that of the Y₂O₃ sample, which was attributed to properties of the residual grain-boundary phase associated with the difference in the cationic radius of the stabilizing cation.     

Synthesis and Characterization of (Ce0.67Tb0.33)MnxMg1−xAl11O19 Phosphors Derived by Sol–Gel Processing

A (Ce_0.67Tb_0.33)Mn _x Mg_{1− x} Al₁₁O₁₉ phosphor powder was synthesized, using a simple sol–gel process, by mixing citric acid with CeO₂, Tb₄O₇, Al(NO₃)₃·9H₂O, Mg(OH)₂·4MgCO₃·6H₂O, and Mn(CH₃COO)₂. The phosphor crystallized completely at 1200°C, and the phosphor particle size was between 1 and 5 μm. The excitation spectrum was characteristic of Ce³⁺, while the emission spectrum was composed of lines from Tb³⁺ and Mn²⁺. The Mn²⁺ gave a green fluorescence band, and concentration quenching occurred when x > 0.10. The luminescent properties of the phosphor were explained by a configurational coordinate model.