XAFS studies of nickel and sulfur speciation in residual oil fly-ash particulate matters (ROFA PM)

XAFS spectroscopy has been employed to evaluate the effect of fuel compositions and combustion conditions on the amount, form, and distribution of sulfur and nickel in size-fractionated ROFA PM. Analysis of S K-edge XANES establish that sulfate is abundant in all PM. However, depending upon the combustion conditions, lesser amounts of thiophenic sulfur, metal sulfide, and elemental sulfur may also be observed. Least-squares fitting of Ni K-edge XANES reveals that most of the nickel in PM is present as bioavailable NiSO4.nH2O. The insoluble Ni mainly exists as a minor species, as nickel ferrite in PM2.5 (PM < 2.5 microm) and nickel sulfide, Ni(x)SY(y) in PM2.5+ (PM > 2.5 microm). The Ni K-edge XANES results are in agreement with the EXAFS data. Such detailed speciation of Ni and S in PM is needed for determining their mobility, bioavailability, and reactivity, and hence, their role in PM toxicity. This information is also important for understanding the mechanism of PM formation, developing effective remediation measures, and providing criteria for identification of potential emission sources. Transition metals complexing with sulfur is ubiquitous in nature. Therefore, this information on metal sulfur complex can be critical to a large body of environmental literature.     

TEM study of PM2.5 emitted from coal and tire combustion in a thermal power station

The research presented here was conducted within the scope of an experiment investigating technical feasibility and environmental impacts of tire combustion in a coal-fired power station. Previous work has shown that combustion of a coal+tire blend rather than pure coal increased bulk emissions of various elements (e.g., Zn, As, Sb, Pb). The aim of this study is to characterize the chemical and structural properties of emitted single particles with dimensions <2.5 microm (PM2.5). This transmission electron microscope (TEM)-based study revealed that, in addition to phases typical of coal fly ash (e.g., aluminum-silicate glass, mullite), the emitted PM2.5 contains amorphous selenium particles and three types of crystalline metal sulfates never reported before from stack emissions. Anglesite, PbSO4, is ubiquitous in the PM2.5 derived from both fuels and contains nearly all Pb present in the PM. Gunningite, ZnSO4-H2O, is the main host for Zn and only occurs in the PM derived from the coal+tire blend, whereas yavapaiite, KFe3+(SO4)2, is present only when pure coal was combusted. We conclude that these metal sulfates precipitated from the flue gas, may be globally abundant aerosols, and have, through hydration or dissolution, a major environmental and health impact.     

Speciation of gas-phase and fine particle emissions from burning of foliar fuels

Fine particle matter with aerodynamic diameter <2.5 microm (PM2.5) and gas-phase emissions from open burning of six fine (foliar) fuels common to fire-prone U.S. ecosystems are investigated. PM2.5 distribution is unimodal within the 10-450 nm range, indicative of an accumulation mode. Smoldering relative to flaming combustion shows smaller particle number density per unit time and median size. Over 100 individual organic compounds in the primarily carbonaceous (>70% by mass) PM2.5 are chemically speciated by gas chromatography/mass spectrometry. Expressed as a percent of PM2.5 mass, emission ranges by organic compound class are as follows: n-alkane (0.1-2%), polycyclic aromatic hydrocarbon (PAH) (0.02-0.2%), n-alkanoic acid (1-3%), n-alkanedioic acid (0.06-0.3%), n-alkenoic acid (0.3-3%), resin acid (0.5-6%), triterpenoid (0.2-0.5%), methoxyphenol (0.5-3%), and phytosterol (0.2-0.6%). A molecular tracer of biomass combustion, the sugar levoglucosan is abundant and constitutes a remarkably narrow PM2.5 mass range (2.8-3.6%). Organic chemical signatures in PM2.5 from open combustion of fine fuels differ with those of residential wood combustion and other related sources, making them functional for source-receptor modeling of PM. Inorganic matter [PM2.5 - (organic compounds + elemental carbon)] on average is estimated to make up 8% of the PM2.5. Wavelength dispersive X-ray fluorescence spectroscopy and ion chromatography identify 3% of PM2.5 as elements and water-soluble ions, respectively. Compared with residential wood burning, the PM2.5 of fine fuel combustion is nitrate enriched but shows lower potassium levels. Gas-phase C2-C13 hydrocarbon and C2-C9 carbonyl emissions are speciated by respective EPA Methods T0-15 and T0-11A. They comprise mainly low molecular weight C2-C3 compounds and hazardous air pollutants (48 wt % of total quantified volatile organic carbon).     

Emissions of chromium, copper, arsenic, and PCDDs/Fs from open burning of CCA-treated wood

Aged and weathered chromated copper arsenate (CCA) treated wood was burned in an open burn research facility to characterize the air emissions and residual ash. The objectives were to simulate, to the extent possible, the combustion of such waste wood as might occur in an open field or someone's backyard; to characterize the composition and particle size distribution (PSD) of the emitted fly ash; to determine the partitioning of arsenic, chromium, and copper between the fly ash and residual ash; and to examine the speciation of the CCA elements. This work reports preliminary air emission concentrations and estimated emission factors for total particulate matter, arsenic (As), chromium (Cr), copper (Cu), and polychlorinated dibenzodioxins/dibenzofurans (PCDD/F) totals and toxic equivalents (TEQs). The partitioning of As, Cr, and Cu between the emitted fly ash and residual ash is examined and thermochemical predictions from the literature are used to explain the observed behavior. Results indicate a unimodal fly ash PSD between 0.1 and 1.0 microm diameter. In addition to a large carbonaceous component, between 11 and 14% of the As present in the burned CCA treated wood was emitted with the air emissions, with the remainder present in the residual ash. In contrast, less than 1% of both the Cr and Cu present in the wood was emitted with the air emissions. PCDD/F levels were unremarkable, averaging 1.7 ng TEQ/kg of treated wood burned, a value typical for wood combustion. Scanning electron microscopy (SEM) was unable to resolve inorganic particles consisting of Cu, Cr, or As in the wood samples, but X-ray absorption fine structure (XAFS) spectroscopy confirmed that the oxidation states of the CCA elements in the wood were Cu2+, Cr3+, and As5+. SEM examination of the fly ash samples revealed some inorganic microcrystals within the mostly carbonaceous fly ash, while XAFS spectroscopy of the same samples showed that the oxidation states after combustion were mixed Cu+ and Cu2+, Cr3+, and mixed As3+ and As5+. Estimates of the ratios of the mixed oxidation states based on the XAFS spectra were As3+/(total As) = 0.8-0.9 and Cu+/(total Cu) = 0.65-0.7. The Cu and Cr present in the fly ash were determined to coexist predominantly in the two oxide phases CuCrO2 and CuCr2O4. These results indicate that the open burning of CCA-treated wood can lead to significant air emissions of the more toxic trivalent form of As in particle sizes that are most respirable.     

Physicochemical characteristics and biological activities of seasonal atmospheric particulate matter sampling in two locations of Paris

Fine particulate matter present in urban areas seems to be incriminated in respiratory disorders. The aim of this study was to relate physicochemical characteristics of PM2.5 (particulate matter collected with a 50% efficiency for particles with an aerodynamic diameter of 2.5 microm) to their biological activities toward a bronchial epithelial cell line 16-HBE. Two seasonal sampling campaigns of particles were realized, respectively, in a kerbside and an urban background station in Paris. Sampled-PM2.5 mainly consist of particles with a size below 1 microm and are mainly composed of soot as assessed by analytical scanning electron microscopy. The different PM2.5 samples contrasted in their PAH content, which was the highest in the kerbside station in winter, as well as in their metal content. Kerbside station samples were characterized by the highest Fe and Cu content, which appears correlated to their hydroxyl radical generating properties measured by electron paramagnetic resonance. Particles were compared by their capacity to induce cytotoxicity, intracellular ROS production, and proinflammatory cytokine release (GM-CSF and TNF-alpha). At a concentration of 10 microg/cm2, all samples induced peroxide production and cytokine release to the similar extent in the absence of cytotoxicity. In conclusion, whereas the PM2.5 samples differ by their PAH and metal composition, they induce the same biological responses likely either due to components bioavailability and/ or interactions between PM components.     

Quantifying hazardous species in particulate matter derived from fossil-fuel combustion

An analysis protocol that combines X-ray absorption near-edge structure spectroscopy with selective leaching has been developed to examine hazardous species in size-segregated particulate matter (PM) samples derived from the combustion of fossil fuels. The protocol has been used to identify and determine quantitatively the amounts of three important toxic species in combustion-derived PM: viz., nickel sulfides in residual oil fly ash (ROFA) PM, and Cr(VI) and As(III) species in coal fly ash PM. Although it has been assumed that these toxic species might exist in PM derived from fossil-fuel combustion, the results presented here constitute the first direct determination of them in combustion-derived PM and their potential bioavailability. Detailed information on the presence of these toxic species in PM samples is of significant interest to epidemiological and toxicological studies of the health effects of both source and ambient PM. Additionally, information is obtained on insoluble forms that may be useful for source attribution and on the distribution of phases between size fractions that may be related to formation mechanisms of specific toxic species during combustion.     

Characterization and source apportionment of particulate matter < or = 2.5 micrometer in Sumatra, Indonesia, during a recent peat fire episode

An intensive field study was conducted in Sumatra, Indonesia, during a peat fire episode to investigate the physical and chemical characteristics of particulate emissions in peat smoke and to provide necessary data for source-receptor analyses. Ambient air sampling was carried out at three different sites located at varying distances from the peatfires to determine changes in mass and number concentrations of PM2.5 and its chemical composition (carbonaceous and nitrogenous materials, polycyclic aromatic hydrocarbons, water-soluble inorganic and organic ions, and total and water-soluble metals). The three sites represent a rural site directly affected by the local peat combustion, a semirural site, and an urban site situated downwind of the peat fires. The mass concentration of PM2.5 and the number concentration of airborne particles were as high as 1600 microg/m3 and 1.7 x 10(5) cm(-3), respectively, in the vicinity of peat fires. The major components of PM2.5 in peat smoke haze were carbonaceous particles, particularly organic carbon, NO3-, and SO4(2-), while the less abundant constituents included ions such as NH4+, NO2-, Na+, K+, organic acids, and metals such as Al, Fe, and Ti. Source apportionment by chemical mass balance receptor modeling indicates that peat smoke can travel long distances and significantly affect the air quality at locations downwind.     

Size-resolved source apportionment of airborne particle mass in a roadside environment

Airborne particulate hopanes, steranes, and polycyclic aromatic hydrocarbons (PAHs) were measured in six size fractions < 1.8 microm particle diameter at one site upwind and two sites downwind of the Interstate 5 freeway in San Diego, CA. The smallest size fraction collected was exclusively in the ultrafine size range (D(p) < 0.1 microm; PM0.1). Size distributions of hopanes, steranes, and PAHs peaked between 0.10-0.18 microm particle aerodynamic diameter with a tail extending into the PM0.1 size range. This pattern is similar to previous dynamometer studies of hopane, sterane, and PAH size distributions emitted from gasoline- and diesel-powered vehicles. Size-resolved source profiles were combined to form an "on-road" profile for motor oil, diesel, and gasoline contributions to EC and OC. The resulting equations were used to predict source contributions to the size distributions of EC and OC in the roadside environment. The method successfully accounted for the majority of the carbonaceous material in particles with diameter < 0.18 microm, with significant residual material in larger size fractions. The peak in both the measured and predicted EC size distribution occurred between 0.1-0.18 microm particle aerodynamic diameter. The predicted OC size distribution peaked between 0.1-0.18 microm particle diameter, butthe measured OC size distribution peaked between 0.56-1.0 microm particle diameter, possibly because of secondary organic aerosol formation. Predicted OC concentrations in particles with diameter < 0.18 microm were greater than measured values 18 m downwind of the roadway but showed good agreement 37 m downwind. The largest source contributions to the PM0.1 and PM0.18 size fractions were different. PM0.18 was dominated by diesel fuel and motor oil combustion products while PM0.1 was dominated by diesel fuel and gasoline fuel combustion products. Total source contributions to ultrafine (PM0.1) EC concentrations 37 m downwind of the roadway were 44 +/- 6% diesel fuel, 21 +/- 1% gasoline, 5 +/- 6% motor oil, and 30% unknown. Total source contributions to ultrafine (PM0.1) OC concentrations 37 m downwind of the roadway were 46 +/- 5% diesel fuel, 44 +/- 5% gasoline, 20 +/- 15% motor oil with a slight overprediction (11%). Diesel fuel appears to make the single largest contribution to ultrafine (PM0.1) particle mass given the fleet distribution during the current experiment.     

Transmission electron microscopy investigation of ultrafine coal fly ash particles

Ultrafine (<100 nm) ash particles in three coal fly ashes (CFA) produced by the combustion of three U.S. coals have been examined by high-resolution transmission electron microscopy (HRTEM), energy-dispersive X-ray spectroscopy (EDS), and electron diffraction. These ultrafine particles, either as primary ash particles derived directly from coal minerals or as secondary products of decomposition and vaporization-condensation processes, show quite different morphologies, compositions, and microstructures as compared to particles in coarser, micrometer-size fractions previously examined by CCSEM. An eastern U.S. bituminous CFA sample shows abundant discrete crystalline particles rich in Fe, Ti, and Al in its ultrafine ash fraction, and crystalline phases down to 10 nm size have been identified. Western U.S. low-rank CFA samples contain considerable amounts of alkaline-earth element aggregates in the form of phosphates, silicates, and sulfates and mixed species. Most of them show crystalline or crystalline plus amorphous characteristics. All three ultrafine samples also exhibit carbonaceous particles in the form of soot aggregates with primary particle size typically between 20 and 50 nm. In the western low-rank ultrafine CFAs, these carbonaceous soot particles were typically mixed or coated with multi-element inorganic species.     

Ce-Ti Amorphous Oxides for Selective Catalytic Reduction of NO with NH(3): Confirmation of Ce-O-Ti Active Sites

The amorphous Ce-Ti mixed oxides were reported to be catalysts for selective catalytic reduction of NO(x) with NH(3), in which Ce and not Ti acts as their solvent in spite of the fact that Ce is low in content. The amorphous catalysts were characterized by X-ray powder diffraction (XRD) and transmission electron microscopy (TEM) equipped with selective area electron diffraction (SAED). The Ce-Ti amorphous oxide shows higher activity than its crystalline counterpart at lower temperatures. Moreover, the presence of small CeO(2) crystallites as for the impregnated sample is deleterious to activity. The Ce-O-Ti short-range order species with the interaction between Ce and Ti in atomic scale was confirmed for the first time to be the active site using temperature programmed reduction with H(2) (H(2)-TPR), in situ FTIR spectra of NO adsorption, X-ray photoelectron spectroscopy (XPS), and X-ray absorption fine-structure (XAFS). Lastly, the Ce-O-Ti structure was directly observed by field-emission TEM (FETEM).     

Surface chemical characterization of 2.5-microm particulates (PM2.5) from air pollution in Salt Lake City using TOF-SIMS, XPS, and FTIR

Particulate matter with a diameter of 2.5 microm collected in Salt Lake City (SLC PM2.5) was studied using TOF-SIMS (time-of-flight secondary-ion mass spectrometry), XPS (X-ray photoelectron spectroscopy), and FTIR (Fourier transform infrared spectroscopy). The high spatial resolution and high surface sensitivity of TOF-SIMS allow the surfaces of individual particulates to be analyzed. The high mass-resolution of TOF-SIMS provides good separation of signals from different chemical species at the same nominal mass, and the extremely high detection sensitivity of TOF-SIMS makes the detection of trace elements possible. Metallic elements such as Li, Na, Mg, Al, K, Ca, Cr, Mn, Fe, Cu, Zn, Cs, and Bi were detected by TOF-SIMS on the surface of SLC PM25. The uranium ion U+ together with its oxide ions UO+ and UO2+ were also found. Inorganic compounds detected include oxides, hydroxides, nitrates, sulfates, silicates, borates, chlorides, etc. Organic compounds detected include hydrocarbons, alcohols, aldehydes, ethers, carboxylic acids, amines, amides, nitriles, etc. A number of polycyclic aromatic hydrocarbons (PAH) and nitrated polycyclic aromatic hydrocarbons were detected by TOF-SIMS. High-resolution XPS Cls spectrum shows functional groups such as C-O, CO2, C-CO2, C-C, and C-H and aromatic pi-pi* shake-up transitions. High-resolution XPS O 1s spectrum indicates the coexistence of different oxygen compounds on the surface of PM2.5. FTIR results confirm the presence of various organic compounds in SLC PM2.5 detected by TOF-SIMS and XPS.     

A non-perturbing scheme for the mineralogical characterization and quantification of inorganic colloids in natural waters

Although the role played by inorganic colloids in natural waters depends on their composition as well as on their size, the characterization of submicron particles has rarely gone beyond describing the morphology and identifying some of the most abundant particles. The process of quantification has been hampered by a lack of suitable analytical methods. This study demonstrates that it is possible to identify and quantify inorganic particles in the colloidal size range by applying a straightforward methodology based on a well-proved, quantitative, and nonperturbing method of sample preparation (direct centrifugation of the samples on transmission electron microscopy grids) in conjunction with particle analysis using widely available techniques: transmission electron microscopy, energy dispersive X-ray spectroscopy (EDS), and selected area electron diffraction (SAED). The method has successfully been applied to six water samples from basins of contrasting geological characteristics. The method has the advantage of minimizing sample modifications by allowing on site sample preparation, using standard equipment, and it is not particularly time-consuming. Notably, the combination of EDS and SAED information makes it possible to characterize and quantify the most abundant components of the colloidal pool in the majority of the aquatic systems: the different types of aluminosilicates.     

Concentration and distribution of heavy metals in urban airborne particulate matter in Frankfurt am Main, Germany

Heavy metal concentrations were measured in airborne dust collected at three sites with different traffic densities from August 2001 to July 2002 in the Frankfurt am Main area. Bulk samples of particulate matter (PM) with an aerodynamic equivalent diameter of <22 microm were collected on cellulose nitrate filters using air filtration devices. Fractionated samples of PM with an aerodynamic equivalent diameter of <10 microm were collected using an eight-stage Andersen impactor. Pb, Cd, Mn, Ni, Zn, V, As, Sb, Cu, Cr, Co, and Ce were determined by inductively coupled plasma sector field mass spectrometry, Pt and Rh were determined by adsorptive voltammetry, and Pd was determined by total reflection X-ray fluorescence analysis. The results show that the highest airborne heavy metal concentrations occurred at the main street with a large volume of traffic. With the exception of Co, V, Ce, and Mn, the heavy metals had an elevated enrichment factor compared to their concentrations in the continental crust. The main street site was especially contaminated with Sb, Zn, Cu, V, and Ni. Motor vehicles are the likely source of emissions. With the exception of Cr, Cu, and Zn, most of the airborne heavy metal concentrations determined for impactor samples deviate slightly from the results for total airborne dust. Heavy metal particle size distributions can be divided into three groups. For metals such as As, Cd, Pb, and V, the main fraction can be found in fine particles with a diameter of <2.1 microm, whereas Ce, Cr, Co, and Ni occur mainly in coarse particles with a diameter of >2.1 microm. Cu, Mn, Sb, Zn, Pt, Pd, and Rh occur in high concentrations in the medium range of the impactor stages (particle diameters of 1.1-4.7 microm). Metal concentrations in fine dust particles are needed to assess the human health risks of their inhalation.     

Measurements of size-segregated emission particles by a sampling system based on the cascade impactor

A special sampling system for measurements of size-segregated particles directly at the source of emission was designed and constructed. The central part of this system is a low-pressure cascade impactor with 10 collection stages for the size ranges between 15 nm and 16 microm. Its capability and suitability was proven by sampling particles atthe stack (100 degrees C) of a coal-fired power station in Slovenia. These measurements showed very reasonable results in comparison with a commercial cascade impactor for PM10 and PM2.5 and with a plane device for total suspended particulate matter (TSP). The best agreement with the measurements made by a commercial impactor was found for concentrations of TSP above 10 mg m(-3), i.e., the average PM2.5/PM10 ratios obtained by a commercial impactor and by our impactor were 0.78 and 0.80, respectively. Analysis of selected elements in size-segregated emission particles additionally confirmed the suitability of our system. The measurements showed that the mass size distributions were generally bimodal, with the most pronounced mass peak in the 1-2 microm size range. The first results of elemental mass size distributions showed some distinctive differences in comparison to the most common ambient anthropogenic sources (i.e., traffic emissions). For example, trace elements, like Pb, Cd, As, and V, typically related to traffic emissions, are usually more abundant in particles less than 1 microm in size, whereas in our specific case they were found at about 2 microm. Thus, these mass size distributions can be used as a signature of this source. Simultaneous measurements of size-segregated particles at the source and in the surrounding environment can therefore significantly increase the sensitivity of the contribution of a specific source to the actual ambient concentrations.     

Characteristics of metals in nano/ultrafine/fine/coarse particles collected beside a heavily trafficked road

Fine particles emitted from vehicles have adverse health effects because of their sizes and chemical compositions. Therefore, this study attempted to characterize the metals in nano (0.010 < Dp < 0.056 microm), ultrafine (Dp < 0.1 microm), fine (Dp < 2.5 microm), and coarse (2.5 < Dp < 10 microm) particles collected near a busy road using a microorifice uniform deposition impactor (MOUDI) and a Nano-MOUDI. The nano particles were found to contain more of traffic-related metals (Pb, Cd, Cu, Zn, Ba, and Ni) than particles of other sizes, although crustal metals accounted for over 90% of all the particulate metals. Most crustal metals, Ba, Ni, Pb, and Zn in ultrafine particles displayed Aitken modes due to their local origins. The Ag, Cd, Cr, Ni, Pb, Sb, V, and Zn were 37, 50, 28, 30, 24, 64, 38, and 22% by mass, respectively, in < 0.1-microm particles, with submicron mass median diameters (MMDs) in PM(0.01-18) (except Zn) (particularly the < 0.1-microm MMDs for Cd and Sb). These levels raise potential health issues. Particle-bound Zn was more abundant in the accumulation mode than in the nucleation/condensation mode, but the opposite was true for Ag, Cd, and Sb. The Ag, Ba, Cd, Pb, Sb, V, and Zn contents in nano particles were strongly associated with diesel fuel, while the Cu, Mn, and Sr in particles < 0.1 microm were more strongly associated with gasoline. The high content of Si in nano particles, more associated with diesel soot than with gasoline exhaust, is another health concern.     

Source apportionment of PM2.5 in the Southeastern United States using solvent-extractable organic compounds as tracers

A chemical mass balance (CMB) receptor model using particle-phase organic compounds as tracers is applied to apportion the primary source contributions to fine particulate matter and fine particulate organic carbon concentrations in the southeastern United States to determine the seasonal variability of these concentrations. Source contributions to particles with aerodynamic diameter < or =2.5 microm (PM2.5) collected from four urban and four rural/suburban sites in AL, FL, GA, and MS during April, July, and October 1999 and January 2000 are calculated and presented. Organic compounds in monthly composite samples at each site are identified and quantified by gas chromatography/mass spectrometry and are used as molecular markers in the CMB model. The major contributors to identified PM2.5 organic carbon concentrations at these sites in the southeastern United States include wood combustion (25-66%), diesel exhaust (14-30%), meat cooking (5-12%), and gasoline-powered motor vehicle exhaust (0-10%), as well as smaller but statistically significant contributions from natural gas combustion, paved road dust, and vegetative detritus. The primary sources determined in the present study when added to secondary aerosol formation account for on average 89% of PM2.5 mass concentrations, with the major contributors to PM2.5 mass as secondary sulfate (30+/-6%), wood combustion (15+/-12%), diesel exhaust (16+/-7%), secondary ammonium (8+/-2%), secondary nitrate (4+/-3%), meat cooking (3+/-2%), gasoline-powered motor vehicle exhaust (2+/-2%), and road dust (2+/-2%). Distinct seasonality is observed in source contributions, including higher contributions from wood combustion during the colder months of October and January. In addition, higher percentages of unexplained fine organic carbon concentrations are observed in July, which are likely due to an increase in secondary organic aerosol formation during the summer season.     

Characterization of airborne particles during production of carbonaceous nanomaterials

Despite the rapid growth in nanotechnology, very little is known about the unintended health or environmental effects of manufactured nanomaterials. The development of nanotechnology risk assessments and regulations requires quantitative information on the potential for exposure to nanomaterials. The objective of this research isto characterize airborne particle concentrations during the production of carbonaceous nanomaterials, such as fullerenes and carbon nanotubes, in a commercial nanotechnology facility. We measured fine particle mass concentrations (PM2.5), submicrometer size distributions, and photoionization potential, an indicator of the particles' carbonaceous content, at three locations inside the facility: inside the fume hood where nanomaterials were produced, just outside the fume hood, and in the background. The measurements were not selective for engineered nanomaterials and may have included both engineered nanomaterials and naturally occurring or incidental particles. Average PM2.5 and particle number concentrations were not significantly different inside the facility versus outdoors. However, large, short-term increases in PM2.5 and particle number concentrations were associated with physical handling of nanomaterials and other production activities. In many cases, an increase in the number of sub-100 nm particles accounted for the majority of the increase in total number concentrations. Photoionization results indicate that the particles suspended during nanomaterial handling inside the fume hood were carbonaceous and therefore likely to include engineered nanoparticles, whereas those suspended by other production activities taking place outside the fume hood were not. Based on the measurements in this study, the engineering controls at the facility appear to be effective at limiting exposure to nanomaterials.     

Chemical characterization of ambient particulate matter near the World Trade Center: elemental carbon, organic carbon, and mass reconstruction

Concentrations of elemental carbon (EC), organic carbon matter (OM), particulate matter less than 2.5 microm (PM2.5), reconstructed soil, trace element oxides, and sulfate are reported from four locations near the World Trade Center (WTC) complex for airborne particulate matter (PM) samples collected from September 2001 through January 2002. Across the four sampling sites, daily mean concentrations ranged from 1.5 to 6.8 microg/m3 for EC, from 10.2 to 31.4 microg/m3 for OM, and from 22.6 to 66.2 microg/m3 for PM2.5. Highest concentrations of PM species were generally measured north and west of the WTC complex. Total carbon matter and sulfate constituted the largest fraction of reconstructed PM2.5 concentrations. Concentrations of PM species across all sites decreased from the period when fires were present at the WTC complex (before December 19, 2001) to the period after the fires. Averaged over all sites, concentrations decreased by 25.6 microg/m3 for PM2.5, 2.7 microg/m3 for EC, and 9.2 microg/m3 for OM from the fire period to after fire period.     

On-line analysis of urban particulate matter focusing on elevated wintertime aerosol concentrations

A 10-day winter sampling campaign was conducted in downtown Toronto for particulate matter (PM) air pollution in the fine (<2.5 microm) size range. An aerosol laser ablation mass spectrometer (LAMS), a tapered-element oscillating microbalance (TEOM), and an aerodynamic particle sizer (APS) were operated in parallel to characterize the PM on-line. In this study, the LAMS observed differences in the chemical composition between three separate episodes with higher PM2.5 mass and APS counts. LAMS results showed that in one instance of elevated PM, organic amines were present in the particulates. Temporal analyses of this episode revealed chemical transformations as the amines, characterized by m/z peaks 58(C3HeN)+, 86(C5H2N)+, and nitrates, increased in number concentration while Ca and hydrocarbon particle classes concurrently decreased. On another day, sulfates were found to have increased significantly. The third event was only 4 h in duration and exhibited an increase in the number of submicron-sized K/hydrocarbons and sulfate-containing particles. In this last event, the hydrocarbons and a K to Fe ratio enrichment indicated there was likely a contribution from a combustion source. This work offers some of the first insights into single particle size and chemistry in a cold winter climate.     

卷烟燃烧灰分形成机制研究

为揭示卷烟燃烧灰分形成机制,采用色差仪、扫描电镜、能量色散X射线谱仪和红外光谱仪等表征卷烟燃烧灰分不同区域以及不同燃烧热解模拟条件下烟丝和卷烟纸残留物的外观、微观形貌、元素分布及化学组成.结果表明:①卷烟燃烧灰分不同区域外观特征呈多样性.②卷烟燃烧过程中,卷烟纸先发生纤维素降解碳化,颜色由白变黑,随后焦炭燃烧,颜色由深...