Assessment of Intestinal Absorption of Vitexin-2″-O-Rhamnoside in Hawthorn Leaves Flavonoids in Rat Using In Situ and In Vitro Absorption Models

The purpose of this study was to investigate the absorption mechanism of vitexin-2″-O-rhamnoside, the index component in hawthorn leaves flavonoids (HLF) in the rat intestine, using two different absorption models, the in situ single-pass intestinal perfusion and the in vitro everted gut sac model. The effective permeability coefficients (P_eff) in the in situ single-pass intestinal perfusion experiments and the apparent permeability coefficients (P_app) in the in vitro everted gut sac experiments were calculated. Furthermore, the influences of the P-glycoprotein inhibitors, verapamil and digoxin, on the intestinal absorption of vitexin-2″-O- rhamnoside in HLF were studied using the above-mentioned two models. Results showed that there were no significant differences in the absorption of vitexin-2″-O-rhamnoside in HLF in four segments of the rat intestine, duodenum, jejunum, ileum, and colon, and at different concentrations of HLF ranging from 0.05 mg/ml to 0.5 mg/ml (P > 0.05). The P_eff values for vitexin-2″-O-rhamnoside in the rat jejunal perfusion at the concentration of 0.05, 0.1, 0.25, and 0.5 mg/ml were (2.48 ± 0.33) × 10^?5; (2.23 ± 0.67) × 10^?5; (2.18 ± 0.48) × 10^?5; and (2.25 ± 0.17) × 10^?5 cm/s, respectively. But there was significant difference between absence and presence of verapamil or digoxin (P < 0.05). P_eff and P_app values of vitexin-2″-O-rhamnoside in HLF were increased in the presence of verapamil or digoxin. In conclusion, vitexin-2″-O-rhamnoside can be classified into high permeability class drug according to the biopharmaceutical classification system. Passive diffusion dominates the absorptive transport behavior of vitexin-2″-O-rhamnoside in HLF. The absorption and secretion are mediated by the efflux transport system, P-gp. The absorption of vitexin-2″-O-rhamnoside in HLF can be enhanced administered together with P-gp inhibitors.     

Cesium preconcentration by recovery from solutions in the form of phosphomolybdate

Abstact  In recovery of Cs from nitric acid solutions in the form of phosphomolybdate of variable composition Cs _x H_3−x PO₄·12MoO₃·nH₂O (x = 3.0−0.8), its content in the solid phase depends on the presence of some other compounds in solution. The impurities can act differently, competing with cesium in precipitate formation, decreasing the oxidant excess, or decomposing the phosphomolybdate anion. Nevertheless, even in the presence of many foreign compounds cesium can be recovered selectively and quantitatively with the formation of a concentrate containing up to ∼150 mg of Cs per gram of the dried precipitate. Cesium can be further concentrated (up to ∼500 mg of Cs per gram) by dissolving the phosphomolybdate in NaOH and precipitating at pH ≈ 10 the known double cesium magnesium phosphate. Original Russian Text ? D.N. Bykhovskii, T.I. Kol’tsova, E.M. Roshchinskaya, 2009, published in Radiokhimiya, 2009, Vol. 51, No. 2, pp. 140–144.     

Current Noise in HgBa2CuO4+δ High Tc Superconductor

Experimental results of current noise in magnetic fields up to 1 kG after zero field cooling and field cooling are reported in bulk HgBa₂CuO_4+δ prepared with vapor–solid reaction in a two-temperature zone reactor. Noise measurements performed in Hg-based superconductor materials are compared with previously studied superconductors, in particular, YBa₂Cu₃O_7?δ. A maximum in the noise is observed at the same resistance, approximately one order of magnitude lower than the normal state value and independently of the applied field. This result is consistent with experiments in bulk YBa₂Cu₃O_7?δ samples and with percolative model simulations of lattice junctions in which the maximum is obtained at the same value of the concentration of superconducting junctions and, thus, at the same macroscopic resistance. Maximum intensity is shown to increase with magnetic field up to 1 kG, with noise values slightly higher in the field cooling procedure. Our results attest that weak-link effects, as in YBa₂Cu₃O_7?δ, dominate superconducting properties of bulk HgBa₂CuO_4+δ. With respect to YBa₂Cu₃O_7?δ, no saturation at high magnetic field in both noise and magnetoresistance measurements is observed.     

Experimental investigation of dry,wet and cryogenic boring of AA 7075 alloy

In this research work, an attempt has been carried out to examine (investigate) and study the dry, wet and cryogenic boring of AA 7075 alloy, which is predominantly used in transport applications in defense (aeronautical parts), oceanic and automaker industries. To ensure direct supply of the coolant, and real-time measurement of cutting temperature a modified boring bar is used (modification is carried out using EDM to accommodate placement of a thermocouple to obtain real-time measurement of temperature readings during the boring cycle). It is observed that during cryogenic boring of AA 7075 alloy there is a considerable reduction in the cutting force (F_c), cutting temperature (T_c) and surface roughness (R_a) by 56.16%, 84.70%, 58.98% compared to dry boring and 48.43%, 80.70%, 34.70% compared to wet boring, respectively. Decrease in F_c and T_c leads to a reduction in high stresses at localized points during machining and in turn curtail wear in workpiece and tool. Lubrication provided by cryogenic fluids also plays a sizable role in reduction of F_c and T_c. Reduction in lower F_c and T_c has a glaring effect on the surface characteristics of the hole produced during the boring process. Tool wear is reduced in cryogenic boring by 36.96% and 17.57% compared to dry and wet boring, respectively. Taguchi and ANOVA was carried out which helped in determining feed as an important parameter with respect to F_c and R_a during boring of AA 7075 under dry, wet and cryogenic conditions whereas speed as an important parameter in determining T_c in dry and wet conditions and feed for T_c in cryogenic boring condition. TOPSIS analysis highlighted speed of 770 rpm and feed of 0.055 mm/min as the most closest to ideal solution for all three different cutting conditions. Surface morphology study after boring of AA 7075 highlighted better surface characteristics in cryogenic bored surface compared to dry and wet boring. Roughness measured in AFM for tool used in boring highlighted a decrease in 86.79% and 66.01% in cryogenic boring in juxtaposition with dry and wet boring, respectively. A surge in compressive residual stress is observed in cryogenic bored surface by 10.41% and 3.5% in juxtaposition with dry and wet boring, respectively, highlighting an abatement in tensile residual stress and better workpiece integrity as compared to dry and wet boring conditions.     

Synthesis and properties of glasses in the K2O–SiO2–Bi2O3–TiO2 system and bismuth titanate (Bi4Ti3O12) nano glass–ceramics thereof

Glasses were prepared by the melt-quench technique in the K₂O–SiO₂–Bi₂O₃–TiO₂ (KSBT) system and crystallized bismuth titanate, BiT (Bi₄Ti₃O₁₂) phase in it by controlled heat-treatment at various temperature and duration. Different physical, thermal, optical, and third-order susceptibility (χ³) of the glasses were evaluated and correlated with their composition. Systematic increase in refractive index (n) and χ³ with increase in BiT content is attributed to the combined effects of high polarization and ionic refraction of bismuth and titanium ions. Microstructural evaluation by FESEM shows the formation of polycrystalline spherical particles of 70–90 nm along with nano-rods of average diameter of 85–90 nm after prolonged heat treatment. A minor increase in dielectric constants (ε_r) has been observed with increase in polarizable components of BiT in the glasses, whereas a sharp increase in ε_r in glass–ceramics is found to be caused by the formation of non-centrosymmetric and ferroelectric BiT nanocrystals in the glass matrix.     

Anisotropic and tensile flow behaviors of Mg alloy AZ31B thin sheet in H24 condition at elevated temperatures

In this work, a series of experiments was performed to explore the effects of anisotropy, strain rate, and temperature on microstructure change and associated mechanical response of a rolled AZ31B-H24 Mg alloy sheet under tension. Tensile tests were carried out on specimens in the 0, 45, and 90° to the rolling direction, using initial strain rates in the range of 4 × 10⁻³ to 1 × 10⁻¹ s⁻¹ at temperatures of 250 and 370 °C. Results showed that variations in flow behavior under tension could be related to the changes in microstructure resulting from applied tensile conditions. Resultant microstructures, such as degree of dynamic recrystallization, grain growth, and shape of the grain, were associated with temperature, strain rate, and tensile loading direction. The initial texture influenced the variations in changes in microstructure and mechanical properties upon testing in different directions. The specimens upon testing in the 45° to the rolling direction yielded higher m-value, lower strength, and greater elongation to failure under all test conditions.     

The role of continuity in residual-based variational multiscale modeling of turbulence

This paper examines the role of continuity of the basis in the computation of turbulent flows. We compare standard finite elements and non-uniform rational B-splines (NURBS) discretizations that are employed in Isogeometric Analysis (Hughes et al. in Comput Methods Appl Mech Eng, 194:4135–4195, 2005). We make use of quadratic discretizations that are C ⁰-continuous across element boundaries in standard finite elements, and C ¹-continuous in the case of NURBS. The variational multiscale residual-based method (Bazilevs in Isogeometric analysis of turbulence and fluid-structure interaction, PhD thesis, ICES, UT Austin, 2006; Bazilevs et al. in Comput Methods Appl Mech Eng, submitted, 2007; Calo in Residual-based multiscale turbulence modeling: finite volume simulation of bypass transition. PhD thesis, Department of Civil and Environmental Engineering, Stanford University, 2004; Hughes et al. in proceedings of the XXI international congress of theoretical and applied mechanics (IUTAM), Kluwer, 2004; Scovazzi in Multiscale methods in science and engineering, PhD thesis, Department of Mechanical Engineering, Stanford Universty, 2004) is employed as a turbulence modeling technique. We find that C ¹-continuous discretizations outperform their C ⁰-continuous counterparts on a per-degree-of-freedom basis. We also find that the effect of continuity is greater for higher Reynolds number flows.     

Effect of Site-Specific Parameters on the Transfer of 137Cs and 90Sr into Freshwater Fishes1,2

The content of ¹³⁷Cs in fallout, fish, and water was measured with the aim to study the role of site-specific parameters on the transfer of ¹³⁷Cs into fishes. The temporal changes of 137Cs and 90Sr in various types of fishes were studied at two sites of Lake Saimaa. The ¹³⁷Cs content in fishes in the Ukonvesi area, which is the north-western part of the lake, was clearly lower than that in the southern parts of the lake, in Ala-Saimaa, although the fallout of ¹³⁷Cs to the Ukonvesi area was somewhat higher than that to Ala-Saimaa. The fallout in 1986 was about 6 kBq m^{- 2} to the Ukonvesi area and about 3 kBq m^{- 2} to the southern parts of the lake. The ¹³⁷Cs content in fishes was the highest in 1988-1989 in Ala-Saimaa, approximately 700 Bq kg^{- 1}, while that in the Ukonvesi area was only about 300 Bq kg^{- 1}, where the values were the highest in 1987. In Ukonvesi the ¹³⁷Cs content in fishes decreased rapidly, being already in 1990 almost at the same level as in 2000. In the southern parts of the lake the decrease in the ¹³⁷Cs content in fishes was much slower. Also the ⁹⁰Sr content in fishes in Ukonvesi was lower than that in Ala-Saimaa. The ¹³⁷Cs content of the water in the Ukonvesi area decreased rapidly, being about 7 Bq m^{- 3} in 1998, while that in the lower areas of the lake was still 15 Bq m^{- 3} in 2000. The ⁹⁰Sr content in water was approximately the same at the both sampling sites (7-8 Bq m^{- 3}). The water chemical parameters, such as potassium, total phosphorus, total nitrogen, chlorophyll a, and electrical conductivity were significantly higher in Ukonvesi than in Ala-Saimaa.     

Regular Trends in Variation of Crystal Structures of Actinide Metals and Their Alloys

The regular trends in variation of crystal structures of 5f actinide metals in their alloys, under theaction of a high pressure, also in alloys of 4f lanthanide metals with plutonium can by explained by par-ticipation of 5f electrons in formation of the interatomic bond. By analogy with the criterion R _m R _4f (the ratio of "metallic" radius R _m to the radius of 4f shell), used for lanthanide metals, the ratio of the metallic radius to the radius of the trivalent ion (R _m/R ^{3 +}) was selected as a measure of this participation. The changes occurring in crystal lattices of americium, curium, and samarium in their alloys with plutonium, phase transitions in transplutonium metals under a high pressure, and also the order of variation of metallic radii along the actinide series are considered.     

Fractal dimension of the grain boundary fracture in creep-fracture of cobalt-based heat resistant alloys

The effects of grain boundary configuration and creep conditions on the fractal dimension of the grain boundary fracture (D _f) were investigated using commercial cobalt-based heat resistant alloys, namely, HS-21 and L-605 alloys. Creep-rupture experiments were carried out under the initial creep stresses of 19.6–176 MPa in the temperature range from 1089–1422 K in air. The value of D _f was larger in specimens with serrated grain boundaries than in those with straight grain boundaries in the HS-21 alloy under the same creep condition, and the difference in the value of D _f between these specimens was large in the scale range of the analysis which was less than about one grain boundary length. However, there was almost no difference in the value of D _f between the specimens with serrated grain boundaries and those with straight grain boundaries in the L-605 alloy, because there was no obvious difference in the microstructure between these specimens. The value of D _f increased with decreasing creep stress in the scale range of the fractal analysis larger than about one grain boundary length in both HS-21 and L-605 alloys, while the stress dependence of D _f was larger in the HS-21 alloy. The stress dependence of D _f was explained by the stress dependence on the number of grain boundary microcracks linked to the fracture surface. The value of D _f estimated in the scale range smaller than about one grain boundary length showed essentially no stress dependence in both L-605 and HS-21 alloys.     

Structural, optical, magnetic and electrical properties of Zn1−x Co x O thin films

Despite a considerable effort aiming at elucidating the nature of ferromagnetism in ZnO-based magnetic semiconductor, its origin still remains debatable. Although the observation of above room temperature ferromagnetism has been reported frequently in the literature by magnetometry measurement, so far there has been no report on correlated ferromagnetism in magnetic, optical and electrical measurements. In this paper, we investigate systematically the structural, optical, magnetic and electrical properties of Zn_1−x Co _x O:Al thin films prepared by sputtering with x ranging from 0 to 0.33. We show that correlated ferromagnetism is present only in samples with x > 0.25. In contrast, samples with x < 0.2 exhibit weak ferromagnetism only in magnetometry measurement which is absent in optical and electrical measurements. We demonstrate, by systematic electrical transport studies that carrier localization indeed occurs below 20–50 K for samples with x < 0.2; however, this does not lead to the formation of ferromagnetic phase in these samples with an electron concentration in the range of 6 × 10¹⁹ cm⁻³ ∼1 × 10²⁰ cm⁻³. Detailed structural and optical transmission spectroscopy analyses revealed that the anomalous Hall effect observed in samples with x > 0.25 is due to the formation of secondary phases and Co clusters.     

Structure–property correlations in the SiO<Subscript>2</Subscript>–PbO–Bi<Subscript>2</Subscript>O<Subscript>3</Subscript> glasses

SiO₂–PbO–Bi₂O₃ glasses having the composition of 35SiO₂–xPbO–(65−x)Bi₂O₃ (where x = 5, 10, 15, 20, 25, 35, 45; in mol%) have been prepared using the conventional melting and annealing method. Density, molar volume and Vickers microhardness of the prepared glasses were measured. Infrared (IR) and UV–visible spectroscopic techniques were used for structural studies of these glasses. Density as well as the microhardness increase systematically and, conversely, the molar volume decreases with increasing the lead oxide content. This behavior can be explained by the correlation with the glass structure. Increasing the lead oxide content (≥20 mol%) increases the network former PbO₄ groups which can play an important role in increasing the connectivity and compactness of the glass matrix via increasing the cross-linking with the other constituent silicate and bismuthate structural units. The increased compactness may explain, in turn, the increase of the density and microhardness. IR spectra reinforce the idea that bismuth participates in the glassy network predominantly as BiO₆ octahedral structural units. UV–VIS optical absorption spectra revealed UV-charge transfer absorption bands related to the contribution of Pb²⁺ ions in the region 350–385 nm; in addition to the extrinsic absorption of trace iron impurities in the range 220–290 nm. In the visible region, three optical bands in the ranges 415–435, 605–650 and 880–890 nm were correlated with the contribution of electronic transitions in Bi³⁺ ions. Calculation of the optical mobility gap and the width of the energy tail of glass from the UV–VIS absorption indicated a slight increase followed by a decrease in their values. The behavior change occurred at the glass in which PbO content is 20 mol% where lead oxide starts to participate into the glassy matrix as a network former. The combination of analytical FTIR and UV–visible spectroscopy provided a consistent picture of structure–property relations in this glass system.     

Dielectric Resonators for the Measurement of Superconductor Thin Films Surface Impedance in Magnetic Fields at High Microwave Frequencies

We present the design and realization of cylindrical dielectric resonators operating in the 40–60 GHz frequency range, designed for the measurement of the surface resistance and of the surface reactance shift in High-T _c Superconductors (HTS) thin films in a dc magnetic field. The resonators are single tone, based on the TE ₀₁₁ mode, and multiple tone, the latter allowing in principle to exploit the simultaneous determination of the surface impedance at different frequencies. As an application example, we report the temperature and field dependencies of the effective surface impedance of some cuprate superconductors thin films. The results are compared with those obtained through the use of a standard metal cavity with a similar Q-factor and operating in the same frequency range. The comparison highlights a superior stability and a higher sensitivity, resulting in an increase of about two orders of magnitude in the resolution of the surface impedance measurement. By contrast, the dissipative part of the superconducting transition (above T/T _c = 0.97) is better studied with the metal cavity. We also present measurements in the vortex state in YBaCa₂Cu₃O_7−δ and Tl₂Ba₂CaCu₂O_8+x that show significantly different physics. PACS: 74.25 Nf.     

Investigation in the sintering of Y2O3 powders in the temperature range 1000 to 1400° C

This paper is devoted to a study of the sintering of two Y₂O₃ powders in the temperature range where only minor densification occurs. Two powders have been examined; one powder, Y₂O₃-A, was obtained by decomposition of hydroxide, because earlier examinations showed [11] that use of this powder resulted in the highest densities of samples in the sintering temperature range from 1300 to 1900° C. The second powder, Y₂O₃-D, was purchased externally. In order to ensure that the pores in the Y₂O₃-A compacts closed as late as possible, the heating rates up to the appropriate temperatures (1000 to 1400° C) were varied in the range 0.013 to 6° C sec^–1. The results obtained show that the heating rate in this temperature range, for the powder obtained by decomposition of hydroxide, is of primary importance in the densification of the material, and that cessation of shrinkage was not observed in the period of 240 min.     

X-ray absorption fine structure investigations on heat-treated Cr-doped titania thin films

Chromium-doped titanium oxide thin films were investigated in the as-deposited state and after thermal treatment (723 K for 3 h in air). X-ray diffraction data revealed an improvement in film crystallinity induced by the thermal treatment. Extended X-ray absorption fine structure data revealed similar atomic neighboring around Cr atoms in both as-deposited and annealed samples. A lattice contraction of ~ 2% is observed in the annealed samples. The 67% enhancement of the amplitude of the Cr 1 s X-ray absorption fine structure pre-edge peak after thermal treatment, which is a sign of “dipole-forbidden” 1 s → 3 d transitions, suggests strong alteration in the number of Cr 3 d vacancies, in spite of similar Cr local environment in the two kinds of investigated samples. We discuss here the Cr⁺ → Cr⁴⁺ and Cr²⁺ → Cr⁶⁺ changes induced by thermal treatment, and/or the evolution in local structures without inversion center.Refractive index dispersion spectra in the visible wavelength domain allowed us to compute the values of the dispersion energy, the single-oscillator energy and the coordination number of Ti atoms in both as-deposited and annealed samples.     

Chemical fractionation and translocation of heavy metals in Canna indica L. grown on industrial waste amended soil

A pot experiment was carried out to assess the effect of different amendments of industrial sludge on the growth of Canna indica L. as well as the translocation potential of heavy metals of this plant. The accumulation of metals (Cr, Fe, Cd, Cu, Ni, Zn, Mn and Pb) in different parts of C. indica L. grown on industrial sludge-amended soil increased with time and increasing doses of sludge amendments. Sequential extraction method was followed to estimate the different fractions of heavy metals in sludge-amended soils collected from different periods of this study. The results showed that Mn, Zn, Cd, Cr and Pb were mostly associated with Fe–Mn oxide fraction in all amendments, whereas, Ni was mostly found in residual (RES) fraction. Cu and Fe were found to be higher in organically bounded form (OM) and RES fraction. The metal concentration in C. indica L. after 90 days of experiment started, was in the order of Fe > Cr > Mn > Zn > Ni > Cu > Cd > Pb and the metal translocation was found lesser in shoot. With the increasing percentage of sludge amendments in soil the metal concentrations increased in different parts of plants. Overall, the plant C. indica L. was found to be well adapted in industrial sludge amendments and it may be recommended that this plant was found suitable for phytoremediation of most of the studied metals.     

Influence of Nb2O5 on the varistor behavior of TiO2–Cr2O3 system

This work investigated the influence of Nb₂O₅ dopant on the varistor behavior of the ternary system (99.95 ? x)%TiO₂, 0.05 %Cr₂O₃, x%Nb₂O₅, where x = 0.10; 0.15; 0.20; 0.25 % in mol. The processing was carried out using the conventional oxide mixture method. The initial oxides were homogenized in alcoholic media in a ball mill, for 3 h, dried in oven and isostatically pressed at 210 MPa and sintered at 1,400 °C for 2 h in air atmosphere and cooled at 5 °C/min cooling rate, resulting in pellets with high densification. Electrical measurements in continuous current at different temperatures revealed that for the lowest Nb₂O₅ concentration the breakdown electric field, E_B = 4.41 V/cm and non-linear coefficient, α = 4.6 were obtained, and for the highest Nb₂O₅ concentration the breakdown electric field, E_B = 9.71 V/cm and non-linear coefficient, α = 15.3 were obtained. These low values in the breakdown electric field enable these varistor systems to be used in protection systems for low-voltage energy grids. Changes in the potential barrier present in the grain–grain boundaries could also be observed, in which the height increased and the width decreased with the increase in the dopant concentration. However, for x = 0.25 % in mol Nb₂O₅, a significant reduction in the potential barrier height and the voltage per barrier was obtained. Furthermore, the tendency to increase the volume of the unitary cell with the increase of dopant concentration, which was interrupted in the system with 0.25 % Nb₂O₅, was another evidence that suggested the occurrence of Nb₂O₅ segregation in the grain boundaries, or even that the reduction in the average grain size could possibly dilute Nb₂O₅ concentration in the grain boundaries. The average grain size was calculated through SEM micrographs and ranged from 7 to 16 μm, with larger sizes occurring for lower dopant concentrations and presenting higher porosity and lower uniformity in the grains shape.     

Effect of stents coated with a combination of sirolimus and alpha-lipoic acid in a porcine coronary restenosis model

The aim of this study was to evaluate antiproliferative sirolimus- and antioxidative alpha-lipoic acid (ALA)-eluting stents using biodegradable polymer [poly-l-lactic acid (PLA)] in a porcine coronary overstretch restenosis model. Forty coronary arteries of 20 pigs were randomized into four groups in which the coronary arteries had a bare metal stent (BMS, n = 10), ALA-eluting stent with PLA (AES, n = 10), sirolimus-eluting stent with PLA (SES, n = 10), or sirolimus- and ALA-eluting stent with PLA (SAS, n = 10). A histopathological analysis was performed 28 days after the stenting. The ALA and sirolimus released slowly over 30 days. There were no significant differences between groups in the injury or inflammation score; however, there were significant differences in the percent area of stenosis (56.2 ± 11.78 % in BMS vs. 51.5 ± 12.20 % in AES vs. 34.7 ± 7.23 % in SES vs. 28.7 ± 7.30 % in SAS, P < 0.0001) and fibrin score [1.0 (range 1.0–1.0) in BMS vs. 1.0 (range 1.0–1.0) in AES vs. 2.0 (range 2.0–2.0) in SES vs. 2.0 (range 2.0–2.0) in SAS, P < 0.0001] between the four groups. The percent area of stenosis based on micro-computed tomography corresponded with the restenosis rates based on histopathological stenosis in different proportions in the four groups (54.8 ± 7.88 % in BMS vs. 50.4 ± 14.87 % in AES vs. 34.5 ± 7.22 % in SES vs. 28.9 ± 7.22 % in SAS, P < 0.05). SAS showed a better neointimal inhibitory effect than BMS, AES, and SES at 1 month after stenting in a porcine coronary restenosis model. Therefore, SAS with PLA can be a useful drug combination for coronary stent coating to suppress neointimal hyperplasia.