Pt/MnOx–CeO2 catalysts for the complete oxidation of formaldehyde at ambient temperature

MnO_x–CeO₂ mixed oxides with a Mn/(Mn + Ce) molar ratios of 0–1 were prepared by a modified coprecipitation method and investigated for the complete oxidation of formaldehyde. The MnO_x–CeO₂ with Mn/(Mn + Ce) molar ratio of 0.5 exhibited the highest catalytic activity among the MnO_x–CeO₂ mixed oxides. Structure analysis by X-ray powder diffraction and temperature-programmed reduction of hydrogen revealed that the formation of MnO_x–CeO₂ solid solution greatly improved the low-temperature reducibility, resulting in a higher catalytic activity for the oxidation of formaldehyde. Promoting effect of Pt on the MnO_x–CeO₂ mixed oxide indicated that both the Pt precursors and the reduction temperature greatly affected the catalytic performance. Pt/MnO_x–CeO₂ catalyst prepared from chlorine-free precursor showed extremely high activity and stability after pretreatment with hydrogen at 473 K. 100% conversion of formaldehyde was achieved at ambient temperature and no deactivation was observed for 120 h time-on-stream. The promoting effect of Pt was ascribed to enhance the effective activation of oxygen molecule on the MnO_x–CeO₂ support.     

Quantified NOx adsorption on Pt/K/gamma-Al2O3 and the effects of CO2 and H2O

A multi-component NO_x-trap catalyst consisting of Pt and K supported on γ-Al₂O₃ was studied at 250 °C to determine the roles of the individual catalyst components, to identify the adsorbing species during the lean capture cycle, and to assess the effects of H₂O and CO₂ on NO_x storage. The Al₂O₃ support was shown to have NO_x trapping capability with and without Pt present (at 250 °C Pt/Al₂O₃ adsorbs 2.3 μmols NO_x/m²). NO_x is primarily trapped on Al₂O₃ in the form of nitrates with monodentate, chelating and bridged forms apparent in Diffuse Reflectance mid-Infrared Fourier Transform Spectroscopy (DRIFTS) analysis. The addition of K to the catalyst increases the adsorption capacity to 6.2 μmols NO_x/m², and the primary storage form on K is a free nitrate ion. Quantitative DRIFTS analysis shows that 12% of the nitrates on a Pt/K/Al₂O₃ catalyst are coordinated on the Al₂O₃ support at saturation.

When 5% CO₂ was included in a feed stream with 300 ppm NO and 12% O₂, the amount of K-based nitrate storage decreased by 45% after 1 h on stream due to the competition of adsorbed free nitrates with carboxylates for adsorption sites. When 5% H₂O was included in a feed stream with 300 ppm NO and 12% O₂, the amount of K-based nitrate storage decreased by only 16% after 1 h, but the Al₂O₃-based nitrates decreased by 92%. Interestingly, with both 5% CO₂ and 5% H₂O in the feed, the total storage only decreased by 11%, as the hydroxyl groups generated on Al₂O₃ destabilized the K–CO₂ bond; specifically, H₂O mitigates the NO_x storage capacity losses associated with carboxylate competition.     

Preparation and characterization of LaFe1−xMgxO3/Al2O3/FeCrAl: Catalytic properties in methane combustion

MnO_x–CeO₂ mixed oxides prepared by sol–gel method, coprecipitation method and modified coprecipitation method were investigated for the complete oxidation of formaldehyde. Structure analysis by H₂-TPR and XPS revealed that there were more Mn⁴⁺ species and richer lattice oxygen on the surface of the catalyst prepared by the modified coprecipitation method than those of the catalysts prepared by sol–gel and coprecipitation methods, resulting in much higher catalytic activity toward complete oxidation of formaldehyde. The effect of calcination temperature on the structural features and catalytic behavior of the MnO_x–CeO₂ mixed oxides prepared by the modified coprecipitation was further examined, and the catalyst calcined at 773 K showed 100% formaldehyde conversion at a temperature as low as 373 K. For the samples calcined below 773 K, no any diffraction peak corresponding to manganese oxides could be detected by XRD measurement due to the formation of MnO_x–CeO₂ solid solution. While the diffraction peaks corresponding to MnO₂ phase in the samples calcined above 773 K were clearly observed, indicating the occurrence of phase segregation between MnO₂ and CeO₂. Accordingly, it was supposed that the strong interaction between MnO_x and CeO₂, which depends on the preparation route and the calcination temperature, played a crucial role in determining the catalytic activity toward the complete oxidation of formaldehyde.     

Catalytic reduction of NOx with H2/CO/CH4 over PdMOR catalysts

Conversion of NO_x with reducing agents H₂, CO and CH₄, with and without O₂, H₂O, and CO₂ were studied with catalysts based on MOR zeolite loaded with palladium and cerium. The catalysts reached high NO_x to N₂ conversion with H₂ and CO (>90% conversion and N₂ selectivity) range under lean conditions. The formation of N₂O is absent in the presence of both H₂ and CO together with oxygen in the feed, which will be the case in lean engine exhaust. PdMOR shows synergic co-operation between H₂ and CO at 450–500 K. The positive effect of cerium is significant in the case of H₂ and CH₄ reducing agent but is less obvious with H₂/CO mixture and under lean conditions. Cerium lowers the reducibility of Pd species in the zeolite micropores. The catalysts showed excellent stability at temperatures up to 673 K in a feed with 2500 ppm CH₄, 500 ppm NO, 5% O₂, 10% H₂O (0–1% H₂), N₂ balance but deactivation is noticed at higher temperatures. Combining results of the present study with those of previous studies it shows that the PdMOR-based catalysts are good catalysts for NO_x reduction with H₂, CO, hydrocarbons, alcohols and aldehydes under lean conditions at temperatures up to 673 K.     

Effect of Na-addition on catalytic activity of Pt-ZSM-5 for low-temperature NO–H2–O2 reactions

The effect of additives on Pt-ZSM-5 catalysts was studied for the selective NO reduction by H₂ in the presence of excess O₂ (NO–H₂–O₂ reaction) at 100 °C. The reaction of NO in a stream of 0.08% NO, 0.28% H₂, 10% O₂, and He balance yielded N₂ with less than 10% selectivity, which could not be increased by changing Pt loading or H₂ concentration in the gas feed. Co-impregnation of NaHCO₃ and Pt onto ZSM-5 decreased the BET surface area and the Pt dispersion. Nevertheless, the Na-loaded catalyst (Na-Pt-ZSM-5) exhibited the higher NO_x conversion (>90%) and the N₂ selectivity (ca. 50%). Such a high catalytic activity even at high Na loadings (≥10 wt.%) is completely contrast to other Na-added Pt catalyst systems reported so far. Further improvement of N₂ selectivity was attained by the post-impregnation of NaHCO₃ onto Pt-ZSM-5. In situ DRIFT measurements suggested that the addition of Na promotes the adsorption of NO as NO₂⁻-type species, which would play a role of an intermediate to yield N₂. The introduction of Lewis base to the acidic supports including ZSM-5 would be applied to the catalyst design for selective NO–H₂–O₂ reaction at low temperatures.     

Direct decomposition of nitric oxide over Ba catalysts supported on CeO2-based mixed oxides

The direct decomposition of nitric oxide (NO) over barium catalysts supported on various metal oxides was examined in the absence and presence of O₂. Among the Ba catalysts supported on single-component metal oxides, Ba/Co₃O₄ and Ba/CeO₂ showed high NO decomposition activities, while Ba/Al₂O₃, Ba/SiO₂, and Ba/TiO₂ exhibited quite low activities. The effect of an addition of second components to Co and Ce oxides was further examined, and it was found that the activities were significantly enhanced using Ce–Mn mixed oxides as support materials. XRD results indicated the formation of CeO₂–MnO_x solid solutions with the cubic fluorite structure. O₂-TPD of the CeO₂–MnO_x solid solutions showed a large desorption peak in a range of relatively low temperature. The BET surface areas of the CeO₂–MnO_x solid solutions were larger than those of pure CeO₂ and Mn₂O₃. These effects caused by the addition of Mn are responsible for the enhanced activities of the Ba catalysts supported on Ce–Mn mixed oxides.     

Transient analysis of the release and reduction of NOx using a Pt/Ba/Al2O3 catalyst

The release and reduction of NO_x in a NO_x storage-reduction (NSR) catalyst were studied with a transient reaction analysis in the millisecond range, which was made possible by the combination of pulsed injection of gases and time resolved time-of-flight mass spectrometry. After an O₂ pulse and a subsequent NO pulse were injected into a pellet of the Pt/Ba/Al₂O₃ catalyst, the time profiles of several gas products, NO, N₂, NH₃ and H₂O, were obtained as a result of the release and reduction of NO_x caused by H₂ injection. Comparing the time profiles in another analysis, which were obtained using a model catalyst consisting of a flat 5 nmPt/Ba(NO₃)₂/cordierite plate, the release and reduction of NO_x on Pt/Ba/Al₂O₃ catalyst that stored NO_x took the following two steps; in the first step NO molecules were released from Ba and in the second step the released NO was reduced into N₂ by H₂ pulse injection. When this H₂ pulse was injected in a large amount, NO was reduced to NH₃ instead of N₂.

A only small amount of H₂O was detected because of the strong affinity for alumina support. We can analyze the NO_x regeneration process to separate two steps of the NO_x release and reduction by a detailed analysis of the time profiles using a two-step reaction model. From the result of the analysis, it is found that the rate constant for NO_x release increased as temperature increase.     

Analysis of the thermodynamic feasibility of NOx decomposition catalysis to meet next generation vehicle NOx emissions standards

Free energy minimization calculations are used to determine the thermodynamic equilibrium concentrations of NO_x and other species in stoichiometric and lean gas mixtures over a range of temperatures and compositions. Under lean (excess N₂ and O₂) conditions, the NO decomposition (NO↔(1/2)N₂+(1/2)O₂) and NO oxidation (NO+(1/2)O₂↔NO₂) equilibria impose lower bounds on the NO_x concentrations achievable by thermodynamic equilibration or NO_x decomposition, and these equilibrium NO_x concentrations can be practically significant. Assuming a perfect isothermal catalyst acting on a representative diesel exhaust stream collected over the federal test procedure (FTP) cycle, equilibrium NO_x levels exceed upcoming California Low Emission Vehicle II (LEV-II) and Tier II NO_x emissions standards for automobiles and trucks at temperatures above approximately 800 K. Consideration of a perfect adiabatic catalyst acting on the same diesel exhaust shows that equilibrium NO_x values can fall below NO_x emissions standards at lower temperatures, but to achieve these low concentrations would require the catalyst to attain 100% approach to equilibrium at very low temperatures. It is concluded that NO_x removal based on a thermodynamic equilibrating catalyst under lean exhaust conditions is not practically viable for automotive application, and that to achieve upcoming NO_x standards will require selective NO_x catalysts that vigorously promote NO_x reactions with reductant and do not promote NO decomposition or oxidation. Finally, the ability of a selective NO_x catalyst system to reduce NO_x concentrations to or below thermodynamic equilibrium values is proposed as a useful measure for selective catalytic reduction (SCR) activity.     

Comparative study of structural properties and NOx storage-reduction behavior of Pt/Ba/CeO2 and Pt/Ba/Al2O3

Differences in the NO_x storage-reduction (NSR) behavior of Pt/Ba/CeO₂ and Pt/Ba/Al₂O₃ have been identified and traced to their different chemical and structural properties. The results show that Pt/Ba/CeO₂ exhibits inferior NO_x storage and, particularly, reduction (regeneration) activity compared to the Al₂O₃ supported catalyst. The incomplete reduction of the stored NO_x-species in Pt/Ba/CeO₂ seems to be caused by a faster and more profound reoxidation of Pt particles during the lean period as evidenced by in situ X-ray absorption spectroscopy. Interestingly, the reduction activity could be significantly improved by a pre-reduction step at mild conditions. Exposure of the Pt/Ba/CeO₂ catalyst to reducing H₂ atmosphere in the temperature range 300–500 °C lead to a moderate increase of Pt particle size which beneficially influenced the regeneration activity. In contrast, pre-reduction at temperatures above 500 °C was unfavorable and resulted in a severe decrease of the regeneration activity, probably due to migration of the partially reduced CeO₂ onto the surface of Pt particles.     

The role of zeolite type on the lean NOx reduction by methane over Pd loaded pentasil zeolites

The lean selective catalytic reduction of NO_x by methane over protonic palladium loaded ZSM-5, FER and MOR, as well as, on bimetallic Pd–Pt-HMOR was examined. Special emphasis was paid on the combined effects of water and SO₂ in the feed stream. Under dry conditions and in the absence of SO₂, the degree of NO_x conversion at 450°C decreases as follows: Pd-HZSM-5>Pd-HMOR>Pd-HFER. Sulfur dioxide alone has no apparent effect on the activity for NO_x reduction, but the coexistence of water and SO₂ inhibits both NO_x and methane conversions. The extent of inhibition by water and SO₂ on NO_x reduction is Pd-HFER>Pd-HZSM-5>Pd-HMOR. Acid mordenite doped with low levels of Pt and Pd leads to an active catalyst that is more tolerant to the presence of either water or SO₂ than the corresponding monometallic Pt- and Pd-HMOR. Nevertheless, NO_x reduction is also inhibited at temperatures below 450°C when SO₂ and water are both present. TPD experiments of water over calcined samples of protonic Pd supported pentasil zeolites, Pd/γ-Al₂O₃ and Pt–Pd-HMOR with and without pretreatment in SO₂+O₂ indicate that sulfation of the surface increases water chemisorption by the support. Therefore, the observed decrease of NO_x reduction on Pd-loaded zeolite catalysts when SO₂ and H₂O coexist in the feed stream may be due to enhanced water inhibition and presumably active site poisoning.     

Relative rates of various steps of NO–CH4–O2 reaction catalyzed by Pd/H-ZSM-5

Reaction mechanism of the reduction of nitrogen monoxide by methane in an oxygen excess atmosphere (NO–CH₄–O₂ reaction) catalyzed by Pd/H-ZSM-5 has been studied at 623–703 K in the absence of water vapor, in comparison with the mechanism for Co-ZSM-5. Kinetic isotope effect for the N₂ formation in NO–CH₄–O₂ vs. NO–CD₄–O₂ reactions was 1.65 at 673 K and decreased with a decrease in the reaction temperature. In addition, H–D isotopic exchange took place significantly in NO–(CH₄+CD₄)–O₂ reaction. These results are in marked contrast with the case of Co-ZSM-5, for which the C–H dissociation of methane is the only rate-determining step, and show that the C–H dissociation is slow but not the only rate-determining step in the case of Pd/H-ZSM-5.

A reaction scheme was proposed, in which the relative rates of the three steps ((i)–(iii) below) vary depending on the reaction conditions.

Further, in contrast to Co-ZSM-5, NO_x–CH₄–O₂ reaction was much slower than CH₄–O₂ reaction for Pd/H-ZSM-5; the presence of NO_x retards the reaction of CH₄ over the latter catalyst, while it accelerates the reaction over the former. It is suggested that CH₄ is activated directly by the Pd atoms in the case of Pd/H-ZSM-5, but by NO₂ strongly adsorbed on Co ion for Co-ZSM-5. The reaction order of the NO–CH₄–O₂ reaction with respect to NO pressure was consistent with this mechanism; 1.05 for Pd/H-ZSM-5 and 0.11 for Co-ZSM-5.     

Reversible sorption–desorption of NOx by mixed oxides under various atmospheres

Characteristics of MnO_y–ZrO₂ and Pt–ZrO₂–Al₂O₃ as reversible sorbents of NO_x were investigated under dynamic changes in atmosphere. These sorbents can be used reversibly with a change of C₃H₈ concentration in the reaction gases. Catalytic reduction of NO occurred in the presence of propane, which was more pronounced on Pt–ZrO₂–Al₂O₃ than on MnO_y-ZrO₂ due to high activity of Pt surface for this reaction on MnO_y in MnO_y–ZrO₂. The sorption was observed as soon as the atmosphere changed from a reducing to an oxidizing one. This implies that a high equilibrium partial pressure of O₂ is necessary for NO uptake since the sorbed NO⁻₃ species becomes stable. The beginning of NO_x desorption atmospheres was somewhat dependent on the amount of stored NO_x. The presence of propane in the gas phase strongly affected the characteristic sorption and desorption properties of MnO_y–ZrO₂ and Pt–ZrO₂–Al₂O₃. The sorption and desorption properties are different for MnO_y–ZrO₂ and Pt–ZrO₂–Al₂O₃, since the noble metal or metal oxide possesses unique activity for the NO reaction with C₃H₈ and the amount of oxygen available for oxidative sorption of NO.     

The selective catalytic reduction of nitrogen oxides by methane on noble metal-loaded sulfated zirconia

The selective catalytic reduction of NO_x by methane on noble metal-loaded sulfated zirconia (SZ) catalysts was studied. Ru, Rh, Pd, Ag, Ir, Pt, and Au-loaded sulfated zirconia catalysts were compared with the intact sulfated zirconia. For the NO–CH₄–O₂ reaction, Ru, Rh, Pd, Ir, and Pt showed promotion effect on NO_x reduction, while for the NO₂–CH₄–O₂ reaction, only Rh and Pd showed promotion effect. Over intact and Rh, Pd, Ag, and Au-loaded sulfated zirconia, NO_x conversion in NO₂–CH₄–O₂ reaction was significantly higher than that in NO–CH₄–O₂ reaction, while clear difference was not observed over Ru, Ir, and Pt-loaded sulfated zirconia. Comparison of [NO₂]/([NO]+[NO₂]) in the effluent gases in NO–O₂ and NO₂–O₂ reactions showed that Ru, Ir, and Pt has high activity for NO oxidation under the reaction conditions. These facts suggest that effects of these metals toward NO_x reduction by methane can be categorized into the following three groups: (i) low activity for NO oxidation to NO₂, and high activity for NO₂ reduction to N₂ (Pd, Rh); (ii) high activity for NO oxidation to NO₂, and low activity for NO₂ reduction to N₂ (Ru, Ir, Pt); (iii) low activity for both reactions (Ag, Au). To confirm these suggestions, combination of these metals were investigated on binary or physically-mixed catalysts. The combination of Pd or Rh with Pt or Ru gave high activity for the selective reduction of NO_x by methane.     

The low-temperature performance of NOx storage and reduction catalyst

The catalytic performance and the behavior of NO_x storage and reduction (NSR) over a model catalyst for lean-burn gasoline engines have been mainly investigated and be discussed based on the temperature and reducing agents use in this study. The experimental results have shown that the NO_x storage amount in the lean atmosphere was the same as the NO_x reduction amount from the subsequent rich spike (RS) above the temperature of 400 °C, while the former was greater than the latter below the temperature of 400 °C. This indicated that when the temperature was below 400 °C compared with the NO_x storage stage, the reduction of the stored NO_x is somehow restricted. We found that the reduction efficiencies with the reducing agents decrease in the order H₂ > CO > C₃H₆ below 400 °C, thus not all of the NO_x storage sites could be fully regenerated even using an excessive reducing agent of CO or C₃H₆, which was supplied to the NSR catalyst, while all the NO_x storage sites could be fully regenerated if an adequate amount of H₂ was supplied. We also verified that the H₂ generation more favorably occurred through the water gas shift reaction than through the steam reforming reaction. This difference in the H₂ generation could reasonably explain why CO was more efficient for the reduction of the stored NO_x than C₃H₆, and hinted as a promising approach to enhance the low-temperature performance of the current NSR catalysts though promoting the H₂ generation reaction.     

Pt-Ba/alumina NOx storage-reduction catalysts: Influence of Ba loading on NOx storage behavior

The NO_x storage behavior of a series of Pt-Ba/Al₂O₃ catalysts, prepared by wet impregnation of Pt/Al₂O₃ with Ba(Ac)₂, has been investigated. The catalysts with Ba loadings in the range 4.5–28 wt.% were calcined at 500 °C in air and subsequently exposed to NO pulses in 5 vol.% O₂/He atmosphere. Catalysts were characterized by means of thermogravimetry (TG) combined with mass spectroscopy (MS) and XRD before and after exposure to NO pulses. Characterization of the calcined catalysts corroborated the existence of three Ba-containing phases which are discernible based on their different thermal stability: BaO, LT-BaCO₃ and HT-BaCO₃. Characterization after NO_x exposure showed that the different Ba-containing phases present in the catalysts possess different reactivity for barium nitrate formation, depending on their interfacial contact. The different Ba(NO₃)₂ species produced upon NO_x exposure could be distinguished based on their thermal stability. The study revealed that during the NO_x storage process a new thermally instable BaCO₃ phase formed by reaction of evolved CO₂ with active BaO. The fraction of Ba-containing species that were active in NO_x storage depended on the Ba loading, showing a maximum at a Ba loading of about 17 wt.%. Lower and higher Ba loading resulted in a significant loss of the overall efficiency of the Ba-containing species in the storage process. The loss in efficiency observed at higher loading is attributed to the lower reactivity of the HT-BaCO₃, which becomes dominant at higher loading, and the increased mass transfer resistance.     

Formation and stability of barium aluminate and cerate in NOx storage-reduction catalysts

The formation and stability of BaAl₂O₄ and BaCeO₃ in Pt-Ba/Al₂O₃ and Pt-Ba/CeO₂ based NO_x storage-reduction (NSR) catalysts has been investigated using kinetic measurements, X-ray diffraction, thermal analysis and X-ray absorption spectroscopy. In as-prepared state, the Ba-component in the NSR catalysts was made up of amorphous BaO and BaCO₃. The formation of BaAl₂O₄ started above 850 °C, whereas the formation of BaCeO₃ was already observed at 800 °C and was faster than that of BaAl₂O₄. The stability of BaAl₂O₄ and BaCeO₃ in various liquid and gaseous atmospheres was different. BaAl₂O₄ was rapidly hydrated at room temperature in the presence of water and transformed to Ba(NO₃)₂ and γ-alumina in the presence of HNO₃, whereas BaCeO₃ was decomposed to much lower extent under these conditions. Interestingly, BaCeO₃ was transformed to Ba(NO₃)₂/CeO₂ in the presence of NO₂/H₂O at 300–500 °C. Also, the presence of CO₂ led to decomposition of barium cerate, which has important consequences for the catalyst ageing under NO_x-storage conditions and can be exploited for regeneration of thermally aged NSR-catalysts.     

The effect of hydrogen on the selective catalytic reduction of NO in excess oxygen over Ag/Al2O3

The selective catalytic reduction (SCR) of nitrogen oxides (NO_x) by propane in the presence of H₂ on sol–gel prepared Ag/Al₂O₃ catalysts (0.5–5 wt.% Ag) was investigated. It was confirmed that hydrocarbon-assisted SCR of NO_x is remarkably enhanced by co-feeding hydrogen to a lean exhaust gas mixture (λ>1), attaining considerable activity within a wide temperature window (470–825 K). The samples had marginal activity at 575 K without co-fed H₂, but achieved up to 60% NO_x conversion in the presence of H₂ at a space velocity of 30,000 h⁻¹. NO₂ as NO_x feed component is not converted to N₂ by C₃H₈ to a substantial extent under lean conditions. This points to an activation route of NO through direct conversion to adsorbed nitrite/nitrate or to a dissociation of NO over Ag⁰, formed through short-term reduction by H₂. The nature of Ag species was characterized by X-ray diffraction, temperature-programmed reduction, pulse thermoanalytical measurements, electron microscopy and FTIR spectroscopy. It could be shown that Ag₂O nano-sized clusters are predominantly present on all samples, whereas formation of silver aluminate could not be confirmed. Nano-sized Ag₂O clusters can reversibly be reduced/reoxidized by H₂. A silver loading higher than 2 wt.% leads to a part of Ag₂O particles, which are thermally decomposed during calcination at 800 K or higher. The catalytic role of this metallic silver is still unclear. Formal kinetic analysis of catalytic data revealed that the activation energy of the overall reaction is significantly lowered in the presence of H₂. The presence of water does not change the activation energy. It is concluded that hydrogen reduces the nano-sized Ag₂O clusters to Ag⁰ on a short-term scale. Zero-valent silver promotes a dissociation pathway of NO_x conversion. The fact that more oxidized ad-species (nitrite/nitrate) are observed in the presence of H₂ is attributed to a dissociative activation of gas-phase oxygen on Ag⁰.     

Catalytic behavior of La–Sr–Ce–Fe–O mixed oxidic/perovskitic systems for the NO+CO and NO+CH4+O2 (lean-NOx) reactions

Mixed oxides of the general formula La_0.5Sr_xCe_yFeO_z were prepared by using the nitrate method and characterized by XRD and Mössbauer techniques. The crystal phases detected were perovskites LaFeO₃ and SrFeO_3−x and oxides -Fe₂O₃ and CeO₂ depending on x and y values. The low surface area ceramic materials have been tested for the NO+CO and NO+CH₄+O₂ (“lean-NO_x”) reactions in the temperature range 250–550°C. A noticeable enhancement in NO conversion was achieved by the substitution of La³⁺ cation at A-site with divalent Sr⁺² and tetravalent Ce⁺⁴ cations. Comparison of the activity of the present and other perovskite-type materials has pointed out that the ability of the La_0.5Sr_xCe_yFeO_z materials to reduce NO by CO or by CH₄ under “lean-NO_x” conditions is very satisfying. In particular, for the NO+CO reaction estimation of turnover frequencies (TOFs, s⁻¹) at 300°C (based on NO chemisorption) revealed values comparable to Rh/-Al₂O₃ catalyst. This is an important result considering the current tendency for replacing the very active but expensive Rh and Pt metals. It was found that there is a direct correlation between the percentage of crystal phases containing iron in La_0.5Sr_xCe_yFeO_z solids and their catalytic activity. O₂ TPD (temperature-programmed desorption) and NO TPD studies confirmed that the catalytic activity for both tested reactions is related to the defect positions in the lattice of the catalysts (e.g., oxygen vacancies, cationic defects). Additionally, a remarkable oscillatory behavior during O₂ TPD studies was observed for the La_0.5Sr_0.2Ce_0.3FeO_z and La_0.5Sr_0.5FeO_z solids.     

Characterization and performance of Pt-USY in the SCR of NOx with hydrocarbons under lean-burn conditions

Pt-USY was used for the selective catalytic reduction of NO_x with hydrocarbons in the presence of excess oxygen. The catalyst was prepared by an ion-exchange method and characterized by XRD, TEM, CO chemisorption, and Ar adsorption at 87 K. The platinum particle size distribution was found to be broad (2–20 nm), with no apparent sintering of the active phase during the HC-SCR process after 25 h time-on-stream. Generally, large metal clusters (>15 nm) are situated at the external surface of the zeolite, while the smaller ones are located in the pores of the support. Pt-USY shows an excellent activity in the deNO_x reaction (molar NO_x conversion 90% at 475 K) with propene as the reductant in 5 kPa O₂, as well as stable operation during time-on-stream. Propane only yields a low NO_x conversion compared to propene. The presence of high oxygen contents (5–10 kPa O₂) slightly inhibits the reaction. No significant decrease in deNO_x activity was observed at high space velocities (up to 100,000 h⁻¹). The presence of SO₂ and H₂O in the feed stream did not significantly affect the deNO_x activity. Pt-USY performs better under lean-burn conditions than other Pt-catalysts supported on e.g. ZSM-5, Al₂O₃, or SiO₂. The selectivity to N₂ was similar to the other Pt-based catalysts (30%), the other major product being N₂O.     

Temperature programmed desorption/surface-reaction study of an anodic alumina supported Ag catalyst for selective catalytic reduction of nitric oxide with propene

On an anodic alumina supported silver catalyst with a low Ag loading (1.68 wt.%), NO_x (NO/He, NO/O₂/He, NO₂/He) adsorption measurements and NO_x-temperature programmed decomposition (TPD)/temperature programmed surface-reaction (TPSR) measurements in different gas streams (He, C₃H₆/He, C₃H₆/O₂/He) were conducted to investigate the formation, consumption and reactivity of surface adsorbed NO_x species.

During NO adsorption, no noticeable uptake of NO was detected. Introducing oxygen greatly improved the formation of ads-NO_x species. A greater quantity of surface nitrate species was found after NO₂ adsorption, accompanied with gaseous NO release. The result of TPSR demonstrates the surface nitrate species can be effectively and preferentially reduced by propene. When introducing oxygen into the propene gas stream of TPSR test, the significantly increased amount of reacted nitrate undoubtedly shows the importance of oxygen in activating propene. The pathway for the selective reduction of NO_x in the presence of excess oxygen is proposed to pass through the selective reduction of the adsorbed nitrate species with the activated propene.

The enhanced NO_x conversion when replacing NO with NO₂ was attributed to the stronger NO_x adsorption capacity and oxidation ability of NO₂, than those for NO. With increasing oxygen concentration, the difference between NO and NO₂ would gradually decrease, and finally disappear in a high excess of oxygen.