AZ31镁合金钕基转化膜研究（英文）

通过化学转化成膜在AZ31镁合金表面制备了钕基转化膜。利用称重实验和OCP测试研究了钕基转化膜的成膜过程,利用SEM,EDS和XPS表征了膜层形貌,微观结构和组成成分。研究了空白样品与镀膜样品在质量分数3.5%NaCl溶液中浸泡不同时间后样品表面形貌和成分。结果表明钕基转化膜可以有效的降低AZ31镁合金在NaCl溶液中的腐蚀速率。利用XRD和电化学测试了经过后处理以后的钕基转化膜的成分和耐蚀性能,结果说明后处理可以进一步改善钕基转化膜的腐蚀性能。     

AZ31镁合金表面钼酸盐（Na2MoO4）转化膜的研究

采用不同配比的Na2MoO4-NaF钼酸盐溶液对AZ31镁合金表面进行化学转化。测试了转化膜在3．5％NaCl溶液中的腐蚀率。经金相组织、SEM、EDS检测,结果分析表明：转化膜较均匀、致密,由MoO4、MgF2组成。在20％Na2MoO4—6％NaF溶液转化后的AZ31镁合金的腐蚀率为11．1881mm／a,为未经转化的AZ31合金30．3256mm／a腐蚀率的36．9％。     

镁基牺牲阳极腐蚀行为研究

采用静态失重法、动电位扫描法和交流阻抗法研究了高纯镁和AZ31合金在3.5%NaCl溶液中的腐蚀行为.结果表明：高纯镁在3.5%的NaCl溶液中的平均腐蚀速率要小于AZ31合金,腐蚀后在高纯镁表面形成了一层氧化膜,阻碍进一步腐蚀,而由于第二相与基体发生电化学反应的AZ31合金腐蚀过程继续维持.用SEM观察两者的腐蚀形貌发现,AZ31合金整个表面都被剧烈的腐蚀;而高纯镁表面腐蚀均匀,且腐蚀程度较浅.      

汽车用AZ91镁合金的耐腐蚀性能

以AZ91镁合金为研究对象,研究了NaCl溶液的浓度、腐蚀时间、温度和搅拌速度对AZ91镁合金耐腐蚀性的影响。利用扫描电镜观察了腐蚀后的表面形貌和横截面形貌,定性分析了AZ91镁合金在NaCl溶液中的腐蚀行为。结果表明,随NaCl溶液浓度、腐蚀时间、温度和搅拌速度增加,AZ91镁合金腐蚀速率主要呈递增趋势,且腐蚀形式为沿晶腐蚀。     

AZ31镁合金表面锡酸盐化学转化膜的研究

对AZ31镁合金表面采取锡酸盐化学转化处理,采用对比试验测定了转化膜在质量分数3.5%NaCl溶液中的腐蚀率,利用扫描电镜(SEM)及能谱(EDS)观察分析了转化膜的形貌和元素含量.结果表明:经锡酸盐转化后的AZ31镁合金的腐蚀率为2.65mm/a,未经转化的AZ31镁合金的腐蚀率为30.36mm/a,耐蚀性有明显提高;锡酸盐转化液pH值在3.5～12范围时对AZ31镁合金均形成了转化膜保护层.     

镁合金阳极氧化膜在NaCl溶液中的腐蚀行为

利用盐水浸泡实验研究了AZ91D镁合金阳极氧化膜层在3．5％NaCl溶液中的腐蚀行为。结果表明：AZ91D镁合金阳极氧化膜层不论封闭与否,在中性NaCl溶液中浸泡出现第一个腐蚀点后,膜层表面均很少再出现新的腐蚀点,而是原有的腐蚀点向纵、横两个方向扩展形成腐蚀坑,表面呈“树枝”状腐蚀形貌;浸泡溶液的pH值对阳极氧化膜层的耐蚀性影响很大,酸性溶液中的腐蚀速率明显大于中、碱性溶液的;随浸泡溶液温度的升高阳极氧化膜层的腐蚀速率加快。据此,提出了AZ91D镁合金阳极氧化膜层在NaCl溶液中腐蚀过程的模型。     

AZ31镁合金表面钼酸盐(Na_2MoO_4)转化膜的研究

采用不同配比的Na2MoO4-NaF钼酸盐溶液对AZ31镁合金表面进行化学转化,测试了转化膜在3.5%NaCl溶液中的腐蚀率。经金相组织、SEM、EDS检测,结果分析表明:转化膜较均匀、致密,由MoO4、MgF2组成。在20%Na2MoO4-6%NaF溶液转化后的AZ31镁合金的腐蚀率为11.1881mm/a,为未经转化的AZ31合金30.3256mm/a腐蚀率的36.9%。     

AZ31镁合金钼酸盐转化膜

利用钼酸盐溶液在AZ31镁合金表面获得棕黄色的转化膜。用扫描电镜（SEM）和X射线光电子能谱（XPS）对膜层的形貌和组分进行研究,采用动电位极化曲线测试对膜层的耐蚀性进行研究。结果表明：膜的微观形态由球形颗粒构成,膜层厚度约12 μm,对镁合金的覆盖作用良好;转化膜表层中Mo元素主要以MoO3形式存在,在膜的内部钼主要以MoO2和MoO（OH）2存在,并含有部分MoO3;钼酸盐转化膜在阳极极化过程中发生明显的钝化,腐蚀电位正移683 mV,腐蚀电流密度降低2个数量级,明显提高AZ31镁合金的耐蚀性能。同时对镁合金表面钼酸盐转化膜的成膜机理进行初步探讨。     

磁控溅射镀钛提高 AZ31 镁合金耐磨耐蚀性能的研究

目的提高AZ31镁合金的耐磨及耐腐蚀性能。方法采用磁控溅射技术对镁合金进行表面镀钛处理,用扫描电镜研究膜基界面形貌及界面成分,分析结合性能。通过摩擦磨损试验,对比分析镁合金基体和镀Ti膜样品的耐磨性能;通过Tafel极化曲线,对比分析镁合金基体和镀Ti膜样品的耐蚀性能。结果 Ti膜均匀致密,与镁合金基体结合良好。镁合金镀Ti膜后,摩擦系数和磨损失重率下降,腐蚀电位向正方向移动了430 m V,腐蚀电流密度从10.83 m A/cm2下降到2.62×10-7m A/cm2。结论磁控溅射镀Ti膜提高了AZ31镁合金的耐磨和耐蚀性能。     

氯化铈对镁合金在NaCl溶液中的缓蚀作用

采用电化学阻抗法和动电位极化曲线法研究了氯化铈对镁合金AZ31在3.5％NaCl溶液中腐蚀行为的影响,用扫描电镜(SEM)和能谱仪(EDS)分析了腐蚀产物膜的形貌和成分.结果表明,当NaCl溶液中加入50～200mg/L氯化铈时,镁合金的腐蚀速率均有降低,当稀土含量为l00mg/L时,腐蚀速率最低;加入适当的稀土,腐蚀...     

Effects of Post-weld Heat Treatment on Microstructure,Mechanical Properties and the Role of Weld Reinforcement in 2219 Aluminum Alloy TIG-Welded Joints

In as-welded state, each region of 2219 aluminum alloy TIG-welded joint shows diff erent microstructure and microhardness due to the diff erent welding heat cycles and the resulting evolution of second phases. After the post-weld heat treatment, both the amount and the size of the eutectic structure or θ phases decreased. Correspondingly, both the Cu content in α-Al matrix and the microhardness increased to a similar level in each region of the joint, and the tensile strength of the entire joint was greatly improved. Post-weld heat treatment played the role of solid solution strengthening and aging strengthening. After the post-weld heat treatment, the weld performance became similar to other regions, but weld reinforcements lost their reinforcing eff ect on the weld and their existence was more of an adverse eff ect. The joint without weld reinforcements after the post-weld heat treatment had the optimal tensile properties, and the specimens randomly crack in the weld zone.     

The First Phase of the SRIF Industrialized Base in ＂West Area＂ Has Been Put into Operation

After nearly two years＇ tense construction, the first phase of industrialized base of Shenyang Research Institute of Foundry （SRIF）, located at the Tiexi Casting and Forging Industrial Park in the west of Tiexi District, has now been completed and formally put into operation.     

Thermodynamics Study on the Decomposition of Chromite with KOH

Institute of Process Engineering, Chinese Academy of Sciences, China, has proposed a method for oxidative leaching of chromite with potassium hydroxide. Understanding the mechanism of chromite decomposition, especially in the potassium hydroxide fusion, is important for the optimization of the operating parameters of the oxidative leaching process. A traditional thermodynamic method is proposed and the thermal decomposition and the reaction decomposition during the oxidative leaching of chromite with KOH and oxygen is discussed, which suggests that chromite is mainly destroyed by reactions with KOH and oxygen. Meanwhile, equilibrium of the main reactions of the above process was calculated at different temperatures and oxygen partial pressures. The stable zones of productions, namely, K2CrO4 and Fe2O3, increase with the decrease of temperature, which indicates that higher temperature is not beneficial to thermodynamic reactions. In addition, a comparison of the general alkali methods is carried out, and it is concluded that the KOH leaching process is thermodynamically superior to the conventional chromate production process.     

Influence of Heat Treatment on Damping Behaviour of the Magnesium Wrought Alloy AZ61

The effect of isochronal heat treatments for 1h on variation of damping, hardness and microstructural change of the magnesium wrought alloy AZ61 was investigated. Damping and hardness behaviour could be attributed to the evolution of precipitation process. The influence of precipitation on damping behaviour was explained in the framework of the dislocation string model of Granato and Lücke.     

Effect of Rare Earth Doping on Impedance,Modulus and Conductivity Properties of Multiferroic Composites:0.5(BiLa_xFe_(1-x)O_3)–0.5(PbTiO_3)

The Lanthanum-doped bismuth ferrite–lead titanate compositions of 0.5(Bi LaxFe1-xO3)–0.5(Pb Ti O3)(x = 0.05,0.10,0.15,0.20)(BLxF1-x-PT) were prepared by mixed oxide method.Structural characterization was performed by X-ray diffraction and shows a tetragonal structure at room temperature.The lattice parameter c/a ratio decreases with increasing of La(x = 0.05–0.20) concentration of the composites.The effect of charge carrier/ion hopping mechanism,conductivity,relaxation process and impedance parameters was studied using an impedance analyzer in a wide frequency range(102–106Hz) at different temperatures.The nature of Nyquist plot confirms the presence of bulk effects only,and non-Debye type of relaxation processes occurs in the composites.The electrical modulus exhibits an important role of the hopping mechanism in the electrical transport process of the materials.The ac conductivity and dc conductivity of the materials were studied,and the activation energy found to be 0.81,0.77,0.76 and 0.74 e V for all compositions of x = 0.05–0.20 at different temperatures(200–300 °C).     

Quantitative Analysis of the Crystallographic Orientation Relationship Between the Martensite and Austenite in Quenching–Partitioning–Tempering Steels

The orientation relationships(ORs)between the martensite and the retained austenite in low-and medium-carbon steels after quenching–partitioning–tempering process were studied in this work.The ORs in the studied steels are identified by selected-area electron diffraction(SAED)as either K–S or N–W ORs.Meanwhile,the ORs were also studied based on numerical fitting of electron backscatter diffraction data method suggested by Miyamoto.The simulated K–S and N–W ORs in the low-index directions generally do not well coincide with the experimental pole figure,which may be attributed to both the orientation spread from the ideal variant orientations and high symmetry of the low-index directions.However,the simulated results coincide well with experimental pole figures in the high-index directions{123}_(bcc).A modified method with simplicity based on Miyamoto’s work was proposed.The results indicate that the ORs determined by modified method are similar to those determined by Miyamoto’method,that is,the OR is near K–S OR for the low-carbon Q–P–T steel,and with the increase of carbon content,the OR is closer to N–W OR in medium-carbon Q–P–T steel.     

Growth Kinetics of Single Inclusion Particle in Molten Melts

On the basis of the single-particle framework, a new theory on inclusion growth in metallurgical melts is developed to study the kinetics of inclusion growth on account of reaction and collision. The studies show that the early growth of inclusion depends on reaction growth and Brawnian motion collision, and where the former is decisive, the late growth depends on turbulence collision and Stokes＇ collision, and where the former is dominant; collision growth is very quick during the smelting process, lessened in the refining process, but nearly negligible in the continuous casting process.     

Theoretical Analysis for the Motion and Temperature of Melt Droplets in Spray Degassing Process

The motion of melt droplets in spray degassing process was analyzed theoretically. The height of the treatment tank in spray degassing process could be determined by the results of theoretical calculation of motion of melt droplets. To know whether the melt droplets would solidify during spraying process, the balance temperature of melt droplets was also theoretically analyzed. Then proof experiments for theoretical results about temperature of melt droplets were carried. In comparison, the experimental results were nearly similar to the calculation results.     

Using Finite Element and Contour Method to Evaluate Residual Stress in Thick Ti-6Al-4V Alloy Welded by Electron Beam Welding

This work was to reveal the residual stress profile in electron beam welded Ti-6Al-4V alloy plates(50 mm thick) by using finite element and contour measurement methods.A three-dimensional finite element model of 50-mmthick titanium component was proposed,in which a column–cone combined heat source model was used to simulate the temperature field and a thermo-elastic–plastic model to analyze residual stress in a weld joint based on ABAQUS software.Considering the uncertainty of welding simulation,the computation was calibrated by experimental data of contour measurement method.Both test and simulated results show that residual stresses on the surface and inside the weld zone are significantly different and present a narrow and large gradient feature in the weld joint.The peak tensile stress exceeds the yield strength of base materials inside weld,which are distinctly different from residual stress of the thin Ti-6Al-4V alloy plates presented in references before.     

Microstructures and Tensile Properties of Ultrafine-Grained Ni–(1–3.5) wt% SiC_(NP) Composites Prepared by a Powder Metallurgy Route

Silicon carbide nanoparticle-reinforced nickel-based composites(Ni–Si CNP),with a Si CNPcontent ranged from1 to 3.5 wt%,were prepared using mechanical alloying and spark plasma sintering.In addition,unreinforced pure nickel samples were also prepared for comparative purposes.To characterize the microstructural properties of both the unreinforced pure nickel and the Ni–Si CNPcomposites transmission electron microscopy(TEM) was used,while their mechanical behavior was investigated using the Vickers pyramid method for hardness measurements and a universal tensile testing machine for tensile tests.TEM results showed an array of dislocation lines decorated in the sintered pure nickel sample,whereas,for the Ni–Si CNPcomposites,the presence of nano-dispersed Si CNPand twinning crystals was observed.These homogeneously distributed Si CNPwere found located either within the matrix,between twins or on grain boundaries.For the Ni–Si CNPcomposites,coerced coarsening of the Si CNPassembly occurred with increasing Si CNPcontent.Furthermore,the grain sizes of the Ni–Si CNPcomposites were much finer than that of the unreinforced pure nickel,which was considered to be due to the composite ball milling process.In all cases,the Ni–Si CNPcomposites showed higher strengths and hardness values than the unreinforced pure nickel,likely due to a combination of dispersion strengthening(Orowan effects) and particle strengthening(Hall–Petch effects).For the Ni–Si CNPcomposites,the strength increased initially and then decreased as a function of Si CNPcontent,whereas their elongation percentages decreased linearly.Compared to all materials tested,the Ni–Si CNPcomposite containing 1.5% Si C was found more superior considering both their strength and plastic properties.