一种高性能14位采样保持电路

设计了一种应用于流水线型模数转换器的14位100 MHz采样保持电路,并在电路设计中,提出了一种改进型的栅压自举采样开关电路。在不增加电路复杂性的情况下,栅压自举采样开关电路可以有效地增加采样开关管的开启时间和关断时间,以及电路的可靠性。采样保持电路采用电容翻转式结构,以及采用增益提高的全差分折叠式共源共栅跨导放大器来实现。采用SMIC 1.8 V/3.3 V 0.18 μm 1P6M CMOS工艺对电路进行设计与仿真。仿真结果显示,在10.009765 MHz输入信号,100 MHz工作频率下,输出信号的无杂散动态范围(SFDR)为95.9 dB,与传统自举开关相比,提高了16.3 dB。     

一种14位125MHz采样/保持电路的设计

设计了一种高性能采样/保持(S/H)电路,采用全差分电容翻转型的主体结构,有效减小了噪声和功耗.在电路设计中,采用栅压自举开关,极大地减小了非线性失真,同时,有效地抑制了输入信号的直流偏移.采样/保持放大器电路采用折叠共源共栅结构,由于深亚微米工艺中器件本征增益减小,S/H电路为达到更高增益,采用增益提升技术.设计的采样/保持电路采用0.18μm1P5M工艺实现,在1.8V电源电压、125 MHz采样速率下,输出差动摆幅达到2 V(VP-P),输入信号到奈奎斯特频率时仍能达到98 dB以上的无杂散动态范围(SFDR),其性能满足14位精度、125MHz转换速率的流水线ADC要求.     

一种低功耗的13位100MS／s采样保持电路

采用TSMC0．18μm 1P6MCMOS工艺设计了一种高性能低功耗采样保持电路。该电路采用全差分折叠增益自举运算放大器和栅压自举开关实现。在3．3V电源电压下,该电路静态功耗仅为16．6mw。在100MHz采样频率时,输入信号在奈奎斯特频率下该电路能达到91dB的SFDR,其有效精度可以达到13位。     

一种3V13位40MHz低功耗采样／保持电路

设计了一种3 V 13位40 MHz低功耗采样保持电路.该电路采用带增益提高的全差分折叠式共源共栅运算放大器,满足高速高精度的要求;同时,采用带哑元补偿管的栅压自举开关,减小了采样开关带来的非线性失真.使用XFAB 0.35 μm CMOS工艺库,对整体电路和分块电路进行了仿真和分析.     

一种12位100MSPS采样保持电路的设计

基于0.13μm/3.3V CMOS工艺,设计了一种用于12bit 100MSPS Pipeline AIC的采样保持(S/H)电路.采用具有高线性度双边对称的无馈通自举采样开关,获得高增益、宽带宽的跨导前馈补偿共源共栅两级全差分跨导放大器,以及能显著降低增益误差的相关双采样S/H拓扑结构来搭建S/H电路.仿真结果表明:当在11.27MHz的输入信号,111MHz的采样信号下,该S/H电路无杂散动态范围(SFDR)86.4dB,功耗为32mW.     

两倍增益10位100 MSPS CMOS采样/保持电路

提出了一种两倍增益高线性、高速、高精度采样/保持电路。该采样/保持电路通过对输入信号实现两倍放大,改善了高频非线性失真;一种新型的消除衬底偏置效应的采样开关,有效地提高了采样的线性度;高增益和宽带宽的折叠共源共栅运算放大器保证了采样/保持电路的精度和速度。整个电路以0.35μm AMS Si CMOS模型库验证。模拟结果显示,在输入信号为49.21875MHz正弦波,采样频率为100 MHz时,增益误差为70.9μV,SFDR可达到84.5 dB。     

用于10位100 MS/s流水线A/D转换器的采样保持电路

设计了一个用于10位100 MHz采样频率的流水线A/D转换器的采样保持电路。选取了电容翻转结构;设计了全差分套筒式增益自举放大器,可以在不到5 ns内稳定在最终值的0.01%内;改进了栅压自举开关,减少了与输入信号相关的非线性失真,提高了线性度。采用TSMC 0.25μm CMOS工艺,2.5 V电源电压,对电路进行了仿真和性能验证,并给出仿真结果。所设计的采样保持电路满足100 MHz采样频率10位A/D转换器的性能要求。     

采样保持电路中全差分增益提高放大器设计

介绍了一种全差分增益增强CMOS运算放大器的设计和实现。该放大器用于12位20 MHz采样频率的流水线模/数转换器(A/D)的采样保持电路。为了实现大的输入共模范围,采用折叠式共源共栅放大器。主放大器采用开关电容共模反馈电路,辅助放大器则采用简单的连续时间共模反馈电路。该放大器采用CMOS 0.5μm工艺,电源电压为3.3 V。Cadence Spectre仿真结果显示,在负载为6 p F的情况下,其增益为99 d B,单位增益带宽为318 MHz,相位裕度为53°。     

一种应用于流水线ADC采样保持电路的设计

介绍了一种应用于12位、10MS/s流水线模数转换器前端的高性能采样保持（SH）电路的设计。该电路采用全差分电容翻转型结构及下极板采样技术,有效地减少噪声、功耗及电荷注入误差。采用一种改进的栅源电压恒定的自举开关,极大地减小电路的非线性失真。运算放大器为增益增强型折叠式共源共栅结构,能得到较高的带宽和直流增益。该采样保...     

12位50 MHz流水线ADC采样保持电路实现

对采样保持电路进行研究,对增益提高的运算放大器进行2阶系统模拟,得到最佳设计参数;提出一种栅压自举开关电路结构;设计了一个用于12位50 MHz流水线A/D转换器的采样保持电路.采用SMIC 0.35 μm混合CMOS工艺,对整个A/D转换器进行实现.测试结果表明,采样保持电路完全满足设计要求.     

Resolution Enhancement Technology:Integrated Process Solutions using OPC

DUV lithography, using the 248 nm wavelength, is a viable manufacturing option for devices with features at 130 nm and less. Given the low kl value of the lithography, integrated process development is a necessary method for achieving acceptable process latitude. The application of assist features for rule based OPC requires the simultaneous optimization of the mask, illumination optics and the resist.Described in this paper are the details involved in optimizing each of these aspects for line and space imaging.A reference pitch is first chosen to determine how the optics will be set. The ideal sigma setting is determined by a simple geometrically derived expression. The inner and outer machine settings are determined, in turn,with the simulation of a figure of merit. The maximum value of the response surface of this FOM occurs at the optimal sigma settings. Experimental confirmation of this is shown in the paper.Assist features are used to modify the aerial image of the more isolated images on the mask. The effect that the diffraction of the scattering bars (SBs) has on the image intensity distribution is explained. Rules for determining the size and placement of SBs are also given.Resist is optimized for use with off-axis illumination and assist features. A general explanation of the material' s effect is discussed along with the affect on the through-pitch bias. The paper culminates with the showing of the lithographic results from the fully optimized system.     

Cost-effective test solutions for smart card and other integrated flash applications

From its emergence in the late 1980s as a lower cost alternative to early EEPROM technologies, flash memory has evolved to higher densities and speedsand rapidly growing acceptance in mobile applications.In the process, flash memory devices have placed increased test requirements on manufacturers. Today, as flash device test grows in importance in China, manufacturers face growing pressure for reduced cost-oftest, increased throughput and greater return on investment for test equipment. At the same time, the move to integrated flash packages for contactless smart card applications adds a significant further challenge to manufacturers seeking rapid, low-cost test.     

Theoretical analysis of the relationship between the Brillouin gain coefficient and the strain in the optical-fiber sensors

The relation between the power of the Brillouin signal and the strain is one of the bases of the distributed fiber sensors of temperature and strain. The coefficient of the Bfillouin gain can be changed by the temperature and the strain that will affect the power of the Brillouin scattering. The relation between the change of the Brillouin gain coefficient and the strain is thought to be linear by many researchers. However, it is not always linear based on the theoretical analysis and numerical simulation. Therefore, errors will be caused if the relation between the change of the Brillouin gain coefficient and the strain is regarded as to be linear approximately for measuring the temperature and the strain. For this reason, the influence of the parameters on the Brillouin gain coefficient is proposed through theoretical analysis and numerical simulation.     

An improved parallel thinning algorithm with two subiterations

The parallel thinning algorithm with two subiterations is improved in this paper. By analyzing the notions of connected components and passes, a conclusion is drawn that the number of passes and the number of eight-connected components are equal. Then the expression of the number of eight-connected components is obtained which replaces the old one in the algorithm. And a reserving condition is proposed by experiments, which alleviates the excess deletion where a diagonal line and a beeline intersect. The experimental results demonstrate that the thinned curve is almost located in the middle of the original curve connectivelv with single pixel width and the processing speed is high.     

Novel fiber-optical interferometer with miniaturized probe for in-hole measurements

Today, micro-system technology and the development of new MEMS （Micro-Electro-Mechanical Systems） are emerging rapidly. In order for this development to become a success in the long run, measurement systems have to ensure product quality. Most often, MEMS have to be tested by means of functionality or destructive tests. One reason for this is that there are no suitable systems or sensing probes available which can be used for the measurement of quasi inaccessible features like small holes or cavities. We present a measurement system that could be used for these kinds of measurements. The system combines a fiber optical, miniaturized sensing probe with low-coherence interferometry, so that absolute distance measurements with nanometer accuracy are possible.     

Development of the readout system for waveguide multilayer optical card

Waveguide multilayer optical card （WMOC） is a novel storage device of three-dimensional optical information. An advanced readout system fitting for the WMOC is introduced in this paper. The hardware mainly consists of the light source for reading, WMOC, motorized stages addressing unit, microscope imaging unit, CCD detecting unit and PC controlling ＆ processing unit. The movement of the precision motorized stage is controlled by the computer through Visual Basic （VB） language in software. A control panel is also designed to get the layer address and the page address through which the position of the motorized stages can be changed. The WMOC readout system is easy to manage and the readout result is directly displayed on computer monitor.     

Study of waveguide coupling efficiency in hybrid silicon lasers

This paper presents a new method to increase the waveguide coupling efficiency in hybrid silicon lasers. We find that the propagation constant of the InGaAsP emitting layer can be equal to that of the Si resonant layer through improving the design size of the InP waveguide. The coupling power achieves 42% of the total power in the hybrid lasers when the thickness of the bonding layer is 100 nm. Our result is very close to 50% of the total power reported by Intel when the thickness of the thin bonding layer is less than 5 nm. Therefore, our invariable coupling power technique is simpler than Intel＇s.     

Collinear phase-matching study of terahertz-wave generation via difference frequency mixed in GaAs and Inp

The collinearly phase-matching condition of terahertz-wave generation via difference frequency mixed in GaAs and InP is theoretically studied. In collinear phase-matching, the optimum phase-matching wave hands of these two crystals are calculated. The optimum phase-matching wave bands in GaAs and lnP are 0.95-1.38μm and 0.7-0.96μm respectively. The influence of the wavelength choice of the pump wave on the coherent length in THz-wave tuning is also discussed. The influence of the temperature alteration on the phase-matching and the temperature tuning properties in GaAs crystal are calculated and analyzed. It can serve for the following experiments as a theoretical evidence and a reference as well.     

Effects of the alloy compositions on the phonon-polaritons in ternary mixed crystals

Composition dependence of bulk and surface phonon-polaritons in ternary mixed crystals are studied in the framework of the modified random-element-isodisplacement model and the Bom-Huang approximation. The numerical results for Several Ⅱ - Ⅵ and Ⅲ- Ⅴ compound systems are performed, and the polariton frequencies as functions of the compositions for ternary mixed crystals AlxGa1-xAs, GaPxAS1-x, ZnSxSe1-x, GaAsxSb1-x, GaxIn1-xP, and ZnxCd1-xS as examples are given and discussed. The results show that the dependence of the energies of two branches of bulk phonon-polaritons which have phonon-like characteristics, and surface phonon-polaritons on the compositions of ternary mixed crystals are nonlinear and different from those of the corresponding binary systems.     

New insert layer structure OLEDs

An insert layer structure organic electroluminescent device（OLED） based on a new luminescent material （Zn（salen）） is fabricated. The configuration of the device is ITO/CuPc/NPD/Zn（salen）/Liq/LiF/A1/CuPc/NPD/Zn（salen）/Liq/LiF/A1. Effective insert electrode layers comprising LiF（1nm）/Al（5 nm） are used as a single semitransparent mirror, and bilayer cathode LiF（1 nm）/A1（100 nm） is used as a reflecting mirror. The two mirrors form a Fabry-Perot microcavity and two emissive units. The maximum brightness and luminous efficiency reach 674 cd/m^2 and 2.652 cd/A, respectively, which are 2.1 and 3.7 times higher than the conventional device, respectively. The superior brightness and luminous efficiency over conventional single-unit devices are attributed to microcavity effect.