Lowering Crystallization Temperatures by Seeding in Structurally Diphasic Al2O3-MgO Xerogels

Thermal reactions in 93% Al₂O₃-7% MgO and 95.8% Al₂O₃-4.2% MgO gels seeded with α-Al₂O₃, MgAl₂O₄, α-Fe₂O₃, and SiO₂, sols were investigated by differential thermal analysis to determine the extent of nucleation catalysis of solid-state reactions. Seeding with α-Al₂O₃ lowered the α-Al₂O₃ crystallization temperature in these xerogels by 100° to 150°C. Spinel seeds have much less effect on the γ-α transition, and α-Fe₂O₃ and SiO₂ seeds do not affect it significantly. Isostructural seeding of gels may therefore permit lower ceramic processing temperatures.     

Fabrication of Nano-Scaled α-Al2O3 Crystallites Through Heterogeneous Precipitation of Boehmite in a Well-Dispersed θ-Al2O3-Suspension

The possibility of eliminating finger or vermicular growth of α-Al₂O₃ particles obtained by calcination of boehmite was examined. Heterogeneous precipitation of boehmite in a well-dispersed θ-Al₂O₃ suspension was first prepared, in which the mass ratio of boehmite to θ-crystallite was evaluated to form agglomerates of similar sizes that will form α-Al₂O₃ crystallites of <100 nm in diameter. θ- to α-phase transformation of alumina experiences a nucleation and growth mechanism, with the critical size of nucleation being ∼25 nm for θ-Al₂O₃ and the size for accomplishment of transformation followed by finger growth being ∼100 nm. Hence, fabricating agglomerates that would form α-Al₂O₃ crystallites with sizes <100 nm accompanied with appropriate thermal treatments can be a method for obtaining α-Al₂O₃ crystallites free of finger growth. It is found that proper preparation of the agglomerate with appropriate size may initiate a simultaneous and lower temperature θ- to α-Al₂O₃ phase transformation for such powder systems, substantially limiting the mass transfer among the newly formed α-Al₂O₃ particles. Moreover, α-Al₂O₃ crystallites free of finger growth can be obtained.     

Effect of Seeding and Water Vapor on the Nucleation and Growth of α-Al2O3 from γ-Al2O3

Isothermal transformation kinetics and coarsening rates were studied in unseeded and alpha-Al₂O₃-seeded γ-Al₂O₃ powders heated in dry air and water vapor. Unseeded samples heated in dry air transformed to alpha-Al₂O₃ with an activation energy of 567 kJ/mol. Seeding with alpha-Al₂O₃ increased the transformation rates and reduced incubation times by providing low-energy sites for nucleation/growth of the alpha-Al₂O₃ transformation. The activation energy for the transformation was reduced to 350 kJ/mol in seeded samples heated in dry air. Seeded samples completely transformed to alpha-Al₂O₃ after 1 h at 1050°C when heated in dry air compared to 1 h at 925°C when heated in saturated water vapor. The combined effects of a lower nucleation barrier due to seeding and the increased diffusion due to water vapor reduced the activation energy for the transformation by 390 kJ/mol and the transformation temperature by ∼225°C compared to the unseeded samples heated in dry air. The accelerated kinetics is believed to be due to increased surface diffusion.     

Synthesis of Nanocrystalline Aluminum Nitride by Nitridation of δ-Al2O3 Nanoparticles in Flowing Ammonia

Nanocrystalline aluminum nitride (AlN) with surface area more than 30 m²/g was synthesized by nitridation of nanosized δ-Al₂O₃ particles using NH₃ as a reacting gas. The resulting powders were characterized by CHN elemental analysis, X-ray diffraction (XRD), Fourier transform infrared spectra, X-ray photoelectron spectra, field-emission scanning electron microscopy, transmission electron microscopy, and Brunauer–Emmett–Teller surface area techniques. It was found that nanocrystalline δ-Al₂O₃ was converted into AlN completely (by XRD) at 1350°–1400°C within 5.0 h in a single-step synthesis process. The complete nitridation of nanosized alumina at relatively lower temperatures was attributed to the lack of coarsening of the initial δ-Al₂O₃ powder. The effect of precursor powder types on the conversion was also investigated, and it was found that α-Al₂O₃ was hard to convert to AlN under the same conditions.     

Microstructure and Mechanical Properties of Hot-Pressed α-Al2O3-Seeded γ-Alumina Ceramics

High-quality alumina ceramics were fabricated by a hot pressing with MgO and SiO₂ as additives using α-Al₂O₃-seeded nanocrystalline γ-Al₂O₃ powders as the raw material. Densification behavior, microstructure evolution, and mechanical properties of alumina were investigated from 1250°C to 1450°C. The seeded γ-Al₂O₃ sintered to 98% relative density at 1300°C. Obvious grain growth was observed at 1400°C and plate-like grains formed at 1450°C. For the 1350°C hot-pressed alumina ceramics, the grain boundary regions were generally clean. Spinel and mullite formed in the triple-grain junction regions. The bending strength and fracture toughness were 565 MPa and 4.5 MPa·m^1/2, respectively. For the 1300°C sintered alumina ceramics, the corresponding values were 492 MPa and 4.9 MPa·m^1/2.     

Low-Temperature Sintering of Seeded Sol—Gel-Derived, ZrO2-Toughened Al2O3 Composites

Seeding a mixture of boehmite (AIOOH) and colloidal ZrO₂ with α-alumina particles and sintering at 1400°C for 100 min results in 98% density. The low sintering temperature, relative to conventional powder processing, is a result of the small alumina particle size (∼0.3 μm) obtained during the θ-to α-alumina transformation, homogeneous mixing, and the uniform structure of the sol-gel system. Complete retention of pure ZrO₂ in the tetragonal phase was obtained to 14 vol% ZTA because of the low-temperature sintering. The critical grain size for tetragonal ZrO₂ was determined to be ∼0.4 μm for the 14 vol% ZrO₂—Al₂O₃ composite. From these results it is proposed that seeded boehmite gels offer significant advantages for process control and alumina matrix composite fabrication.     

Reinvestigation of Al–Si Spinel Phase in Diphasic Al2O3–SiO2 Gel

Mechanical mixture of γ-Al₂O₃ and amorphous SiO₂, and diphasic Al₂O₃/SiO₂ gels of three different compositions were synthesized. They were subjected to heat treatment to various temperatures in the range 900°–1600°C. Qualitative X-ray diffraction data show that these diphasic gels do not crystallize to a combined mixture of θ-Al₂O₃ and α-Al₂O₃ polymorphs at the intermediate stage, prior to mullite formation. Estimated mullite formation data show that the course of its formation from mixed oxides was different from that of diphasic gels. Results are compared with previous findings and the concept of Al–Si spinel formation in the phase transformation of stoichiometric diphasic gel system is substantiated.     

Seeding of the Reaction-Bonded Aluminum Oxide Process

The effect of the initial α-Al₂O₃ particle size in the reaction-bonded aluminum oxide (RBAO) process on the phase transformation of aluminum-derived γ-Al₂O₃ to α-Al₂O₃, and subsequently densification, was investigated. It has been demonstrated that if the initial α-Al₂O₃ particles are fine (∼0.2 μm, i.e., 2.9 × 10¹⁴γ-Al₂O₃ particles/cm³), then they seed the phase transformation. The fine α-Al₂O₃ decreases the transformation temperature to ∼962°C and results in a finer microstructure. The smaller particle size of the seeded RBAO decreases the sintering temperature to as low as ∼1135°C. The results confirm that seeding can be utilized to improve phase transformations and densification and subsequently to tailor final microstructures in RBAO-derived ceramics.     

High-Pressure Sintering of Nanocrystalline γAl2O3

High-pressure sintering of nanocrystalline γ-A1₂O₃ has been studied over a temperature range of 923-1323 K and at a pressure of 1 GPa. The γ-Al₂O₃ to α-Al₂O₃ transformation temperature changed from 1473 K without pressure to ∼1023 K at 1 GPa. Full density was obtained at 1273 and 1323 K in 10 min. The microhardness value of fully dense α-alumina with a grain size of 142 nm was found to be 25.3 ± 0.8 GPa. The Hall-Petch slope for the very fine grain size range is different from that of the coarse-grained alumina.     

Growth of Tabular α-Al2O3 Grains on Porous Alumina Substrate

Gradient, porous alumina ceramics were prepared with the characteristics of microsized tabular α-Al₂O₃ grains grown on a surface with a fine interlocking feature. The samples were formed by spin-coating diphasic aluminosilicate sol on porous alumina substrates. The sol consisted of nano-sized pseudo-boehmite (AlOOH) and hydrolyzed tetraethyl orthosilicate [Si(OC₂H₅)₄]. After drying and sintering at 1150°–1450°C, the crystallographic and chemical properties of the porous structures were investigated by analytical electron microscopy. The results show that the formation of tabular α-Al₂O₃ grains is controlled by the dissolution of fine Al₂O₃ in the diphasic material at the interface. The nucleation and growth of tabular α-Al₂O₃ grains proceeds heterogeneously at the Al₂O₃/glass interface by ripening nano-sized Al₂O₃ particles.     

Formation and Transformation of TiO2 (Anatase) Solid Solution in the System TiO2—Al2O3

In the system TiO₂—Al₂O₃, TiO₂ (anatase, tetragonal) solid solutions crystallize at low temperatures (with up to ∼ 22 mol% Al₂O₃) from amorphous materials prepared by the simultaneous hydrolysis of titanium and aluminum alkoxides. The lattice parameter a is relatively constant regardless of composition, whereas parameter c decreases linearly with increasing Al₂O₃. At higher temperatures, anatase solid solutions transform into TiO₂ (rutile) with the formation of α-Al₂O₃. Powder characterization is studied. Pure anatase crystallizes at 220° to 360°C, and the anatase-to-rutile phase transformation occurs at 770° to 850°C.     

Nanocrystalline α-Al2O3 Using Sucrose

Nanocrystalline α-Al₂O₃ ceramic powders have been prepared from an aqueous solution of aluminum nitrate and sucrose. Soluble Al ion-sucrose solution forms the precursor material once it is completely dehydrated. Heat treatment of the dehydrated precursors at low temperature (600°C) results in the formation of porous single-phase α-Al₂O₃. The precursor and heat-treated powders have been characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), and BET surface area analysis. The phase-pure nanocrystalline α-Al₂O₃ particles had an average specific surface area of >190 m²/g, with an average pore size between 18 and 25 nm.     

Influence of Cr and Fe on Formation of α-Al2O3 from γ-Al2O3

The effect of Cr and Fe in solid solution in γ-Al₂O₃ on its rate of conversion to α-Al₂O₃ at 1100°C was studied by X-ray diffraction. The δ form of Al₂O₃ was the principal intermediate phase produced from both pure γ-Al₂O₃ and that containing Fe³⁺ in solid solution, although addition of Fe greatly reduced crystallinity. Reflectance spectra and magnetic susceptibilities showed that Cr exists as Cr⁶⁺ in γ-Al₂O₃ and as Cr³⁺ in α-Al₂O₃, with θ-Al₂O₃ as the intermediate phase. The intermediates formed rapidly, and the rates of their conversion to α-Al₂O₃ were increased by 2 and 5 wt% additions of Fe and decreased by 2 and 4 wt% additions of Cr. An approximately linear relation observed between α-Al₂O₃ formation and decrease in specific surface area was only slightly affected by the added ions. This relation can be explained by a mechanism in which the sintering of δ- or θ-Al₂O₃, within the aggregates of their crystallites, is closely coupled with conversion of cubic to hexagonal close packing of O^2- ions by synchro-shear.     

Growth of Single-Crystal and Polycrystalline Thin Films of MgAl2O4 and MgFe2O4

Single-crystal and polycrystalline films of Mg-Al₂O₄ and MgFe₂O₄ were formed by two methods on cleavage surfaces of MgO single crystals. In one procedure, aluminum was deposited on MgO by vacuum evaporation. Subsequent heating in air at about 510°C formed a polycrystalline γ-Al₂O₈ film. Above 540°C, the γ-Al₂O, and MgO reacted to form a single-crystal MgAl₂O₄ film with {001} MgAl₂O₄‖{001} MgO. Above 590°C, an additional layer of MgAl₂O₄, which is polycrystalline, formed between the γ-Al₂O₃ and the single-crystal spinel. Polycrystalline Mg-Al₂O₄ formed only when diffusion of Mg²⁺ ions proceeded into the polycrystalline γ-Al₂O₃ region. Corresponding results were obtained for Mg-Fe₂O₄. MgAl₂O₄ films were also formed on cleaved MgO single-crystal substrates by direct evaporation, using an Al₂O₃ crucible as a source. Very slow deposition rates were used with source temperatures of ∼1350°C and substrate temperatures of ∼800°C. Departures from single-crystal character in the films may arise through temperature gradients in the substrate.     

Sintering of Nanophase γ-Al2O3 Powder

The sintering of ultrafine γ-Al₂O₃ powder (particle size ∼10–20 nm) prepared by an inert gas condensation technique was investigated in air at a constant heating rate of 10°C/min. Qualitatively, the kinetics followed those of transition aluminas prepared by other methods. Measurable shrinkage commenced at ∼ 1000°C and showed a region of rapid sintering between ∼1125° and 1175°C followed by a transition to a much reduced sintering rate at higher temperatures. Starting from an initial density of ∼0.60 relative to the theoretical value, the powder compact reached a relative density of 0.82 after sintering to 1350°C. Compared to compacts prepared from the as-received powder, dispersion of the powder in water prior to compaction produced a drastic change in the microstructural evolution and a significant reduction in the densification rate during sintering. The incorporation of a step involving the rapid heating of the loose powder to ∼1300°C prior to compaction (which resulted in the transformation to α-Al₂O₃) provided a method for significantly increasing the density during sintering.     

Nano α-Al2O3 Powder Preparation by Calcining an Emulsion Precursor

An experimental study has been conducted to evaluate the formation of nano α-Al₂O₃ under various conditions, such as different calcining temperatures and emulsion ratios of aqueous aluminum nitrate solutions and oleic acid with a high-speed stirring mixer. Four batches of the precursor powders were calcined at three different temperatures of 1000°, 1050°, and 1100°C for 2 h and a terminal product of nano α-Al₂O₃ powders was obtained. The products have been identified by X-ray diffraction (XRD), specific surface area measurement scanning electron microscope, and transmission electron microscope (TEM). The XRD results show that the phase of powders is determined to be α-Al₂O₃, indicating that the overall process has been effective. The optimum calcination temperature of the precursor powder for crystallization of nano α-Al₂O₃ was found to be 1000°C for 2 h. The TEM image indicates that the particle grains have a sub-spherical shape with a mean size of 50–100 nm.     

Growth of α-Al2O3 Within a Transition Alumina Matrix

The growth of α-Al₂O₃ from a planar specimen of thermally grown γ-alumina on a molybdenum transmission electron microscope grid was studied. The α-Al₂O₃ grows into the transition alumina matrix and then thickens via a ledge growth mechanism. Faceted Mo crystallites cause pinning of α-Al₂O₃ ledges and are larger on α-Al₂O₃ than on the transition alumina matrix.     

Spark-Plasma Sintering of Silicon Carbide Whiskers (SiCw) Reinforced Nanocrystalline Alumina

The combined effect of rapid sintering by spark-plasma-sintering (SPS) technique and mechanical milling of γ-Al₂O₃ nanopowder via high-energy ball milling (HEBM) on the microstructural development and mechanical properties of nanocrystalline alumina matrix composites toughened by 20 vol% silicon carbide whiskers was investigated. SiC_w/γ-Al₂O₃ nanopowders processed by HEBM can be successfully consolidated to full density by SPS at a temperature as low as 1125°C and still retain a near-nanocrystalline matrix grain size (∼118 nm). However, to densify the same nanopowder mixture to full density without the benefit of HEBM procedure, the required temperature for sintering was higher than 1200°C, where one encountered excessive grain growth. X-ray diffraction (XRD) and scanning electron microscopy (SEM) results indicated that HEBM did not lead to the transformation of γ-Al₂O₃ to α-Al₂O₃ of the starting powder but rather induced possible residual stress that enhances the densification at lower temperatures. The SiC_w/HEBMγ-Al₂O₃ nanocomposite with grain size of 118 nm has attractive mechanical properties, i.e., Vickers hardness of 26.1 GPa and fracture toughness of 6.2 MPa·m^1/2.     

Abnormal Grain Growth During Rapid Annealing of Sol–Gel Alumina Thin Film Deposited on Ni-Based Superalloy

A ∼50 nm thick alumina layer was deposited on an Ni-based superalloy substrate by a sol–gel method. α-AlOOH particles presented in the layer after drying at 140°C transformed mostly to α-Al₂O₃ grains within ∼1 min at 1100°C under a low oxygen partial pressure annealing environment. During the same time period, the α-Al₂O₃ grains grew significantly in the lateral direction, resulting in the aspect ratio of grain diameter to thickness of ∼20. The presence of a preferred orientation in the α-Al₂O₃ layer suggested that the mechanism for the lateral growth was abnormal. The lateral growth mechanism appeared to become very slow when a critical thickness (∼100 nm) was reached.     

High-Temperature Transmission Electron Microscopy and X-Ray Powder Diffraction Studies of Polymorphic Phase Transitions in Ba4Nb2O9

Polymorphic phase transitions in Ba₄Nb₂O₉ were studied by thermal analyses, high-temperature transmission electron microscopy and X-ray powder diffractometry. Two stable polymorphs were isolated, low-temperature α-modification and high-temperature γ-modification, with the endothermic phase transition at 1176°C. The α→γ transformation is accompanied by the formation of a 120° domain structure, which is a consequence of hexagonal→orthorhombic unit cell reconstruction. Reheating the presintered γ-Ba₄Nb₂O₉ results in the formation of a metastable γ'-modification (formerly known as β-polymorph) in the temperature range between 360° and 585°C, before the γ→α transformation at 800°C. Above ∼490°C Ba₄Nb₂O₉ becomes moderately sensitive to a loss of BaO. In air the surface of Ba₄Nb₂O₉ grains decomposes to nanocrystalline Ba₅Nb₄O₁₅ and BaO, which instantly reacts with atmospheric CO₂ to form BaCO₃. Surface reaction delays γ→α transformation up to 866°C in air. In vacuum the loss of BaO is even more enhanced and consequently the formation of minor Ba₃Nb₂O₈ phase is observed above 1150°C.