Preparation and swelling properties of homopolymeric alginic acid fractions/poly(N‐isopropyl acrylamide) graft copolymers

Graft copolymers of crosslinked poly(N‐isopropyl acrylamide) (PNIPAAm) and homopolyguluronic acid (GG) and homopolymannuronic acid (MM) fractions of alginic acid were synthesized. MM and GG block fractions were obtained by partial acid hydrolysis of the alkaline extract from the brown seaweed Macrocystis pyrifera. The conjugation of these block fractions with the synthetic polymer was achieved by amidation with crosslinked PNIPAAm functionalized with an amino group at the end of the polymer chain. The structure of conjugates was determined by Fourier transform infrared and NMR spectroscopy. Atomic force microscopy of the graft copolymer GG‐g‐PNIPAAm showed a regular porous pattern, whereas the MM‐g‐PNIPAAm graft copolymer showed a regular netlike structure. Aqueous solutions of the synthesized graft copolymers afforded hydrogels by stirring with 0.1M CaCl₂. The hydrogels showed a well‐defined stimulus–response to temperature and pH. The swelling, thermal, and pH characterizations demonstrated the superior properties of the GG‐g‐PNIPAAm hydrogel over the MM‐g‐PNIPAAm hydrogel. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42398.     

Electrical properties of sorbitol‐doped poly(vinyl alcohol)–poly(acrylamide‐co‐acrylic acid) polymer membranes

Solid polymer membranes from poly(vinyl alcohol) (PVA) and poly(acrylamide‐co‐acrylic acid) (PAA) with varying doping ratios of sorbitol were prepared using the solution casting method. The films were examined with Fourier transform infrared spectroscopy, thermogravimetric analysis, differential scanning calorimetry, and AC impedance spectroscopy. The impedance measurements showed that the ionic conductivity of PVA–PAA polymer membrane can be controlled by controlled doping of sorbitol within the polymer blends. The PVA–PAA–sorbitol membranes were found to exhibit excellent thermal properties and were stable for a wide temperature range (398–563K), which creates a possibility of using them as suitable polymers for device applications. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Hydrosoluble copolymers of acrylamide‐(2‐acrylamido‐2‐methylpropanesulfonic acid). Synthesis and characterization by spectroscopy and viscometry

Hydrosoluble copolymers containing sulfonic acid groups incorporated into a macromolecule were synthesized. The group of polymers studied was obtained by free radical solution polymerization, using potassium persulfate as an initiator. The copolymerization of the monomers 2‐acrylamido‐2‐methylpropanesulfonic acid (AMPS) and acrylamide (AA) was carried out at different pH values of the reaction medium of the monomer mix. The copolymers were characterized by proton nuclear magnetic resonance spectroscopy (¹H NMR) and Fourier transform infrared spectroscopy (FTIR). The viscosity behavior of the copolymers in NaCl solution showed a dependency on the pH of the reaction medium, with higher pH leading to lower viscosities. The acidic conditions of this medium affect the initiator decomposition rate, which is a probable cause of the viscosity variation, and the extent of decomposition increases with increasing pH. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 192–198, 2003     

Evaluation of mechanical properties and physical interactions of a ternary blend of poly(ethylene‐co‐octene)/poly(ethylene‐co‐vinyl acetate)/poly(vinyl chloride) in the molten state

In this work, ethylene‐co‐vinyl acetate (EVA), poly(ethylene‐co‐octene) (POE), and poly(vinyl chloride) (PVC) blends were processed in a molten state process using a corotating twin‐screw extruder to assess both the balance of mechanical properties and physical interactions in the melt state. Tensile measurements, scanning electron microscopy, and oscillatory rheometry were performed. By means of flow curves, the parameters of the power law as well as the distribution of relaxation times were assessed with the aid of a nonlinear regularization method. The mechanical properties for the EVA‐POE blend approximated the values for POE, while inclusion of PVC shifted the modulus values to those of neat EVA. The rise in modulus was corroborated by the PVC phase dispersion as solid particles that act as a reinforcement for the ternary blend. The rheological properties in the molten state show that the POE does not present molecular entanglement effects and so tends both to diminish the EVA mechanical properties and increase the fluidity of the blend. However, the addition of PVC both restored the EVA typical pseudoplastic feature and promoted the increase in the viscosity and the mechanical properties of the ternary blend. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Properties of poly(butylene adipate‐co‐terephthalate) and sunflower head residue biocomposites

Utilization of low‐value agricultural waste for polymer composite materials has great environmental and economical benefits. Sunflower head residue (SHR) as an agricultural waste may be used as a reinforcement in polymeric materials because of its fiber characteristics. In this work, composites of biodegradable poly(butylene adipate‐co‐terephthalate) (PBAT) and SHR were prepared via melt‐extrusion compounding. To improve interfacial compatibility, maleic anhydride (MA) grafted PBAT (PBAT‐g‐MA) was prepared and used as a compatibilizer for the PBAT/SHR composites. The effects of the concentrations of SHR and PBAT‐g‐MA on the morphology, mechanical properties, melt rheology, and water resistance of the composites were examined. Interfacial adhesion between phases in the PBAT/SHR composites was enhanced by the introduction PBAT‐g‐MA as interface‐strengthening agent, resulting in improved mechanical properties and moisture resistance of the composite. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44644.     

Synthesis and properties of the copolymer of acrylamide with 2‐acrylamido‐2‐methylpropanesulfonic acid

A cross‐linked copolymer of acrylamide (AM) with 2‐acrylamido‐2‐methylpropanesulfonic acid (AMPS) was prepared by solution polymerization. In this reaction, potassium persulfate (PPS) and N,N′‐methylenebisacrylamide (NMBA) were used as initiator and cross‐linker, respectively. This copolymer, poly(acrylamide‐co‐2‐acrylamido‐2‐methylpropanesulfonic acid) (PAMA), can absorb up to 1749 g/g of dry polymer in distilled water and 87 g/g of dry polymer in 0.9 wt % NaCl aqueous solution at room temperature. The PAMA also has excellent performance in absorbing pure alcohols. Its absorbencies in methanol and glycol are about 310 g/g and 660 g/g, respectively. The effects of various salt solutions on the swelling properties were studied systematically, and the relationship between the absorbency and the concentrations of the different salt solutions can be expressed as Q = kcⁿ. Experimental results indicate that the absorbencies were stable at different water temperatures. The swelling rates of the copolymer in distilled water and a water/ethanol mixture (V_water:V_alcohol = 1:1) were also investigated, and the results showed that PAMA could absorb 992 g of distilled water per gram of dry polymer and 739 g of water/ethanol mixture per gram of dry polymer in five minutes. The PAMA has such good water retention at higher temperatures that the swollen gel can retain 71.6 and 49.5% of the maximum absorbency after being heated for 9 hours at 60 and 80 °C, respectively. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 3481–3487, 2003     

Synthesis and characterization of cassava starch graft poly(acrylic acid) and poly[(acrylic acid)‐co‐acrylamide] and polymer flocculants for wastewater treatment

Starch‐g‐poly(acrylic acid) and poly[(acrylic acid)‐co‐acrylamide] synthesized via chemically crosslinking polymerization were then each mixed with inorganic coagulants of aluminum sulfate hydrate [Al₂(SO₄)₃·18H₂O], calcium hydroxide [Ca(OH)₂], and ferric sulfate [Fe₂(SO₄)₃] in a proper ratio to form complex polymeric flocculants (CPFs). All CPFs exhibited low water absorbency than those of the uncomplexed superabsorbent copolymers. The color reduction by the CPFs was tested with both synthetic wastewater and selected wastewater samples from textile industries. The synthetic wastewater was prepared from a direct dye in a concentration of 50 mg dm^?3 at pH 7. The CPFs of poly[(acrylic acid)‐co‐acrylamide] with calcium hydroxide at a ratio of 1:2 is the most effective CPF for the wastewater color reduction. The CPF concentration of 500 mg dm^?3 could reduce the color of the synthetic wastewater containing the direct dye solution by 95.4% and that of the industrial wastewater by 76%. Starch‐g‐poly(acrylic acid)/Ca(OH)₂ CPF can reduce the synthetic direct dye and the industrial wastewater by 74% and 18%, respectively. Chemical oxygen demand, residual metal ion concentrations, pHs, turbidity of the wastewater were also investigated and the potential use of the complex polymer flocculants for textile wastewater treatment was indicated. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 2915–2928, 2006     

Study of poly(acrylamide‐co‐2‐acrylamido‐2‐methylpropane sulfonic acid) hydrogels made using gamma radiation initiation

Poly(acrylamide‐co‐2‐acrylamido‐2‐methylpropane sulfonic acid) hydrogels were synthesized using gamma‐radiation‐initiated polymerization. The progress of copolymerization and crosslinking was observed by viscosity measurement on reaction mixtures subjected to varying radiation doses. The copolymer gels were characterized by differential scanning calorimetry, X‐ray diffraction, scanning electron microscopy, infrared spectroscopy, and elemental analysis. The swelling behavior and other properties of the gels were found to be very similar to those of poly(acrylamide‐co‐2‐acrylamido‐2‐methylpropane sulfonic acid) hydrogels synthesized using conventional free‐radical initiation in the presence of crosslinkers. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 1322–1330, 2003     

Starch‐graphene oxide bionanocomposites prepared through melt mixing

Bionanocomposites (BNCs) of waxy corn starch, glycerol, and graphene oxide (GO) or graphite oxide (GrO) were prepared by melt mixing. First, the GrO was pre‐exfoliated in a water solution using ultrasound at 1 wt %. Small‐angle X‐ray scattering was used to determinate the interlaminar separation of GrO and transmission electron microscopy, Fourier infrared spectroscopy, and thermogravimetric analysis were used to characterized the GrO. Next, BNCs were characterized by X‐ray diffraction, scanning electron microscopy, thermogravimetric analysis, and mechanical property measurements. A complete exfoliation of GrO was obtained in the waxy corn matrix. Amorphous X‐ray patterns of the BNCs were observed, indicating that the exfoliated GO avoid the retrogradation of starch. According to scanning electron microscopy results, the BNCs showed an irregular texture and a good dispersion of GO, while thermoplastic starch showed a smooth morphology with a fragile structure. The BNCs exhibited higher thermal stability than thermoplastic starch. The tensile strength and the Young's modulus increased by 140% and 230% at a GO loading levels of 0.5% due to good interfacial interactions of GO and the waxy corn starch matrix. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46037.     

Improving the toughening in poly(lactic acid)‐thermoplastic cassava starch reactive blends

Poly(lactic acid) (PLA), a physical blend of PLA and thermoplastic cassava starch (TPCS) (PLA‐TPCS), and reactive blends of PLA with TPCS using maleic anhydride as compatibilizer with two different peroxide initiators [i.e., 2,5‐bis(tert‐butylperoxy)‐2,5‐dimethylhexane (L101) and dicumyl peroxide (DCP)] PLA‐g‐TPCS‐L101 and PLA‐g‐TPCS‐DCP were produced and characterized. Blends were produced using either a mixer unit or twin‐screw extruder. Films for testing were produced by compression molding and cast film extrusion. Morphological, mechanical, thermomechanical, thermal, and optical properties of the samples were assessed. Blends produced with the twin‐screw extruder resulted in a better grade of mixing than blends produced with the mixer. Reactive compatibilization improved the interfacial adhesion of PLA and TPCS. Scanning electron microscopy images of the physical blend showed larger TPCS domains in the PLA matrix due to poor compatibilization. However, reactive blends revealed smaller TPCS domains and better interfacial adhesion of TPCS to the PLA matrix when DCP was used as initiator. Reactive blends exhibited high values for elongation at break without an improvement in tensile strength. PLA‐g‐TPCS‐DCP provides promising properties as a tougher biodegradable film. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46140.     

Mechanical properties of poly(N‐isopropyl‐acrylamide‐co‐itaconic acid) hydrogels

Hydrogels of N‐isopropylacrylamide and itaconic acid were synthesized with different monomer ratios and with two crosslinking agent concentrations. The different xerogels were immersed in water and the swelling process was conducted up to equilibrium conditions at two temperatures (22 and 37°C). These temperatures are lower and higher than the transition temperature shown by PNIPA hydrogels. The mechanical properties of the different solvated hydrogels were examined by oscillatory shear measurements at 22 and 37°C. The copolymer volume fraction and the elastic storage modulus of the hydrogels decreased as the itaconic acid percentage in the copolymer increased. This behavior was attributed to the higher hydrophilic character of the itaconic acid comonomer. Effective crosslinking density, molar mass between crosslinks, and the polymer–solvent interaction parameter were determined from the experimental values of the elastic storage moduli and the copolymer volume fractions. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 2540–2545, 2002     

Degradation of poly(vinyl alcohol)‐graft‐lactic acid copolymers by Trichotecium roseum fungus

The biodegradation of poly(vinyl alcohol) and poly(vinyl alcohol)‐graft‐lactic acid copolymers was analyzed, using Trichotecium roseum fungus. The samples were examined during biodegradation at different periods of exposure. Structural modifications of the biodegraded samples were investigated by Fourier transform infrared‐attenuated total reflectance spectroscopy, and the surface morphology was investigated by scanning electron microscopy. The static light scattering results concluded that the weight average molecular mass (M_w) of the copolymers increased after biodegradation, because the fractions with low molecular weight of the copolymers were destroyed. The thermal behavior and stability of the samples before and after the biodegradation period were investigated by differential scanning calorimetry (DSC) and thermogravimetric analyses. The thermogravimetric analyses and their derivatives (TG‐DTG) showed that the thermal stability of the biodegraded samples was more raised comparatively to the unbiodegraded ones. The DSC results demonstrated that biodegradation took place in the amorphous domains of the investigated polymer samples and the crystallinity degree increased after 24 biodegradation days. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41777.     

Determination of swelling behavior and morphological properties of poly(acrylamide‐co‐itaconic acid) and poly(acrylic acid‐co‐itaconic acid) copolymeric hydrogels

Poly(acrylamide‐co‐itaconic acid) (PAAmIA) and poly(acrylic acid‐co‐itaconic acid) (PAAIA) copolymeric hydrogels were prepared with different compositions via free‐radical polymerization. Ethylene glycol dimethacrylate (EGDMA) was used as an original crosslinker for these monomers. Gelation percentages of the monomers were studied in detail and it was found that addition of IA into the monomer mixture decreased the gelation percentage. The variation in swelling values (%) with time, temperature, and pH was determined for all hydrogels. PAA, which is the most swollen hydrogel, has the swelling percentage value of 2000% at pH = 7.4, 37°C. Swelling behaviors were explained with detailed SEM micrographs, which show the morphologic differences between dry and swollen hydrogels. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 5994–5999, 2006     

Grafting of acrylic acid‐co‐itaconic acid onto ePTFE and characterization of water uptake by the graft copolymers

Expanded polytetrafluoroethylene, ePTFE, is an attractive material for use as the implant in facial reconstruction surgery because it is bioinert; however, its low surface energy does not facilitate a strong interfacial bond with bone and thus for some applications the surfaces need to be modified to enhance their bone‐integration properties. The surface modification of ePTFE membranes with copolymers of acrylic acid (AA) and itaconic acid (IA) using in situ gamma radiation induced grafting has been studied. Solutions with AA mole fractions ranging from 0.4 to 1.0 have been investigated. Graft yields of 35–50% with water uptakes of greater than 300% were obtained using 3 mol L^?1 aqueous solutions of the monomers and a total incident dose of 10 kGy. The grafts were characterized by Fourier transform infrared and X‐ray photoelectron spectroscopy analyses and the compositional microstructure of the grafted copolymers was investigated. The water uptake by the grafted membranes displayed a complex dependence on polymer chemistry and topology. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41482.     

Synthesis and ferroelectric investigations of poly(vinylidene fluoride‐co‐hexafluoropropylene)‐Mg(NO3)2 films

The free‐standing, flexible, and ferroelectric films of poly(vinylidenefluoride‐co‐hexafluoropropylene) [P(VDF‐HFP)] were prepared by spin coating method. The ferroelectric phase of the films was enhanced by adding magnesium nitrate Mg(NO₃)₂ in different wt % as the additive during the film fabrication. The effects on the structural, compositional, morphological, ferroelectric, dielectric, and leakage current behaviors of the films due to the addition of salt were analyzed. Based on the X‐ray diffraction (XRD) patterns and Fourier Transform Infrared (FTIR) spectra, it is confirmed that the addition of Mg(NO₃)₂ promotes the electroactive β phase that induces the ferroelectric property. The fiber‐like topography of the films exhibits a nodule‐like structure, and the roughness of the films increases by the addition of Mg(NO₃)₂. The ferroelectric studies show the higher polarization values for the composite films than that of the plain P(VDF‐HFP) film. The Piezo‐response force microscope images also confirm the domain switching behavior of the samples. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 44008.     

Properties of extruded starch–poly(methyl acrylate) graft copolymers prepared from spherulites formed from amylose–oleic acid inclusion complexes

Mixtures of high‐amylose corn starch and oleic acid were processed by steam jet cooking, and the dispersions were rapidly cooled to yield amylose–oleic acid inclusion complexes as micron‐ and submicron‐sized spherulites and spherulite aggregates. Dispersions of these spherulite particles were then graft polymerized with methyl acrylate, both before and after removal of uncomplexed amylopectin by water washing. For comparison, granular, uncooked high‐amylose corn starch was also graft polymerized in a similar manner. Graft copolymers with similar percentages of grafted and ungrafted poly(methyl acrylate) (PMA) were obtained from these polymerizations. The graft copolymers were then processed by extrusion through a ribbon die, and the tensile properties of the extruded ribbons were determined. Although extruded ribbons with similar tensile strengths were obtained from the three starch–PMA graft copolymers, much higher values for % elongation were obtained from the spherulite‐containing systems. Also, the tensile properties were not significantly affected by removal of soluble, uncomplexed amylopectin by water washing before graft polymerization. These results are consistent with the observation that these PMA‐grafted starch particles did not melt during extrusion, and that continuous plastic ribbons were formed by fusing these particles together in the presence of small amounts of thermoplastic PMA matrix. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40381.     

Improvement of the thermal properties of poly(3‐hydroxybutyrate) (PHB) by low molecular weight polypropylene glycol (LMWPPG) addition

In this work, blends of poly(3‐hydroxybutyrate) (PHB) with 5, 10, 15, and 20 wt % low molecular weight poly(propylene glycol) (LMWPPG) have been prepared and characterized by scanning electron microscopy (SEM), Fourier transform infrared (FTIR) with attenuated total reflectance (ATR) accessory and simultaneous thermal analysis (TG/DTA). FTIR and thermal analyses suggested that the presence of LMWPPG led to a maximum crystallinity for the blend PHB/PPG (90/10) blend. The presence of LMWPPG also caused a significant increase of the PHB processability window, i.e., the difference of the melting and degradation temperature, of PHB from 105 to 134°C, which is extremely important for the industrial uses of PHB. This PHB stabilization effect is discussed in terms of an intermolecular interaction of the PHB carbonyl with LMWPPG methyl groups which probably hinders the classical radon β‐scission PHB intramolecular decomposition mechanism. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Simultaneously reinforcing and toughening poly(lactic acid) by incorporating reactive melt-functionalized silica nanoparticles

Simultaneously reinforcing and toughening poly(lactic acid) (PLA) was carried out by adding a small amount of functionalized SiO₂ (f-SiO₂) with grafting degraded PLA chains in this work. Typically, the high shear force and high temperature condition of melt blending were employed to accelerate the degradation of PLA and graft the degraded PLA chains onto SiO₂.The structure characterizations revealed that large quantity of degraded PLA chains were grafted onto the surface of SiO₂ by transesterification, condensation, and esterification reactions during melt blending. Due to the improvement in dispersion and interfacial interaction in PLA matrix, the f-SiO₂ exhibited an effective reinforcing and toughening effect for PLA, where the tensile strength, elongation at break, and impact toughness of PLA/f-SiO₂ nanocomposite increased by 14.9, 47.8, and 30.3% compared to neat PLA. Besides, the degree of crystallinity of PLA was significantly improved by the added f-SiO₂, which also contributed to improving mechanical properties. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48834.     

Effects of co‐hard segments on the microstructure and properties thermoplastic poly(ether ester) elastomers

A thermoplastic poly(ether ester) elastomer (TPEE) is composed of polyester hard segments and polyether soft segments. Polyester and polyether segments are often homopolymer segments. This work aims at incorporating poly(butylene phthalate (PBP) as co‐hard segments in the hard segments of poly(butylene terephthalate) (PBT)‐b‐poly(tetramethylene oxide) (PTMO) thermoplastic elastomer, and investigating structures and properties of the resulting materials, denoted as (PBT‐co‐PBP)‐b‐PTMO. (PBT‐co‐PBP)‐b‐PTMO was synthesized from dimethyl terephthalate (DMT), dimethyl phthalate (DMP), PTMO (M_n = 1000 g/mol), and 1,4‐butanediol (BDO). The crystallinity of (PBT‐co‐PBP)‐b‐PTMO first decreased and then increased with increasing PBP content from 5% to 10% due to a decrease in the average sequence length of the PBT hard segments. Its elongation at break was increased by 200–350%. When the mass fractions of PBT and PBP were 42% and 8%, respectively, the (PBT‐co‐PBP)‐b‐PTMO showed the best performance in terms of permanent deformation, strength, and hardness whose values were 30%, 25 MPa, and 37 D, respectively. All the synthesized copolymers had good thermal stability with a decomposition temperature of 400°C or so. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43337.     

Rheological properties of poly(ethylene glycol)/poly(N‐isopropylacrylamide‐co‐2‐acrylamido‐2‐methylpropanesulphonic acid) semi‐interpenetrating networks

For the increasing demands of multifunctional materials in applications such as drug delivery system, a pH‐ and temperature‐responsive polyelectrolyte copolymer gel system was studied using rheometry. Rheological properties, determined by plate–plate rheometry in oscillatory shear, of hydrogels formed by free radical initiated copolymerization of N‐isopropylacrylamide (NIPA) and 2‐acrylamido‐2‐methylpropanesulphonic acid (AMPS) in the presence of methylene bisacrylamide (MBAA) as crosslinker are compared with the properties of semi‐interpenetrating network (SIPN) polyelectrolyte gels made by incorporation of poly(ethylene glycol) with molar mass 6000 g mol^?1 (PEG6000). Based on our systematic studies for this PEG/SIPN system, the effects of initiator and crosslinker concentration, relative proportions of comonomer units in the main chains, PEG6000 content and temperature on viscoelastic properties, unusual high storage moduli at small strain for the SIPN were discussed. The SIPN gel with characteristics of PEG molecules as well as pH and temperature responsiveness from AMPS and NIPA units has potential application in drug delivery system design. Ice‐like rheological behavior of the PEG/AMPS‐NIPA SIPN gels at low temperature was first time reported and water remains homogeneous without phase separation in PEG/AMPS‐NIPA SIPN hydrogels at low temperature may be considered as an ideal candidate for water storage material. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008