Comparative study of composite membranes from nano‐metal‐oxide‐incorporated polymer electrolytes for direct methanol alkaline membrane fuel cells

A series of six composite membranes was prepared with two polymer electrolytes and three inorganic fillers, namely, silica, titania, and zirconia by a solution casting method. Two polymer electrolytes, that is, anion‐exchange membranes, were prepared from polystyrene‐block‐poly(ethylene‐ran‐butylene)‐block‐polystyrene (PSEBS) and polysulfone by chloromethylation and quaternization. A preliminary characterization of the ionic conductivity, methanol permeability, and selectivity ratio was done for all of the prepared composite membranes to check their suitability to work in direct methanol alkaline membrane fuel cells (DMAMFCs). The DMAMFC performance was analyzed with an in‐house fabricated single cell unit with a 25‐cm² area. Maximum performance was achieved for the composite membrane quaternized PSEBS/7.5% TiO₂ and was 74.5 mW/cm² at 60°C. For the comparison purposes, a commercially available anion‐exchange membrane (Anion Membrane International‐7001) was also investigated throughout the study. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Silicone-containing polymer blend electrolyte membranes for fuel cell applications

Polymer electrolyte membranes are developed from blends of chemically durable silicone-containing epoxy (Si-Epoxy) and proton conducting sulfonic polyimide (SPI). A charge-transfer (CT) complex is formed between electron-donating dihydroxynaphthalene units in Si-Epoxy, and electron-accepting naphthalenediimide units in SPI, as confirmed via X-ray diffraction and visible spectroscopy. The blend membranes show comparable mechanical strength to Nafion 211, but the elongation to break is much lower, indicating better resistance to deformation under strain stress, attributed to CT complex formation. The chemical durability of the blend membranes was much higher than pure SPI according to Fenton's test, also attributed to CT complex formation. Meanwhile, the proton conductivity is dependent on the sulfonic acid content of the SPI, which in turn affects the fuel cell performance. The maximum proton conductivity was measured to be 23.1 mS cm⁻¹ at 80°C and 90 %RH for a 1:1 blend, and the membranes were successfully incorporated into PEFCs.     

Highly selective sulfonated poly(vinylidene fluoride‐co‐hexafluoropropylene)/poly(ether sulfone) blend proton exchange membranes for direct methanol fuel cells

Proton exchange membranes (PEMs) based on blends of poly(ether sulfone) (PES) and sulfonated poly(vinylidene fluoride‐co‐hexafluoropropylene) (sPVdF‐co‐HFP) were prepared successfully. Fabricated blend membranes showed favorable PEM characteristics such as reduced methanol permeability, high selectivity, and improved mechanical integrity. Additionally, these membranes afford comparable proton conductivity, good oxidative stability, moderate ion exchange capacity, and reasonable water uptake. To appraise PEM performance, blend membranes were characterized using techniques such as Fourier transform infrared spectroscopy, AC impedance spectroscopy; atomic force microscopy, and thermogravimetry. Addition of hydrophobic PES confines the swelling of the PEM and increases the ultimate tensile strength of the membrane. Proton conductivities of the blend membranes are about 10^?3 S cm^?1. Methanol permeability of 1.22 × 10^?7cm² s^?1 exhibited by the sPVdF‐co‐HFP/PES10 blend membrane is much lower than that of Nafion‐117. AFM studies divulged that the sPVdF‐co‐HFP/PES blend membranes have nodule like structure, which confirms the presence of hydrophilic domain. The observed results demonstrated that the sPVdF‐co‐HFP/PES blend membranes have promise for possible usage as a PEM in direct methanol fuel cells. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43907.     

Wire‐shaped,dye‐sensitized solar cells with poly(vinyl alcohol) gel electrolyte and metal filaments

A kind of wire‐shaped, dye‐sensitized solar cell (WDSSC) composed of poly(vinyl alcohol) (PVA) gel electrolyte and filament‐formed electrodes of titanium and platinum was prepared, and its photovoltaic performance was analyzed with the variations in the dimensions of the electrodes and cells. The dimensions of the wire‐shaped cell were adjusted through the thickness of the TiO₂ layer, the amount of PVA gel electrolyte, and length of the Pt filament. The dominant parameters determining the cell performance were mainly analyzed with the results from the various scanning electron microscopy images and fitted plots of electrochemical impedance spectroscopy. Although the conversion efficiencies of the fabricated WDSSCs were relatively lower than those of the conventional dye‐sensitized solar cells, this development should provide important guiding directions for the design of similar WDSSCs with higher efficiencies. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43439.     

Aliphatic SPI charge‐transfer complex hybrid films for high temperature polymer electrolyte membrane fuel cells

A new method to synthesize polymer electrolyte membranes based on charge‐transfer (CT) complexes for high temperature fuel cells is investigated. Aliphatic sulfonated polyimide (SPI) CT complex hybrid films are prepared. Aliphatic units are introduced into the SPI main chain to increase the elasticity compared with aromatic SPI films. Electron‐donating compounds are included to form a CT complex, resulting in improved control over mechanical strength, water uptake, and thermal stability. The resulting thermal properties of the SPI CT films are sufficient to operate at elevated temperature (up to 120 °C), and the proton conductivity is comparable to that of Nafion 115. These films are thus promising alternative membranes for high temperature polymer electrolyte fuel cell applications. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46087.     

Study of poly(organic palygorskite-methyl methacrylate)/poly(ethylene oxide) blended gel polymer electrolyte for lithium-ion batteries

In this study, the composite polymer was prepared by blending poly(ethylene oxide) (PEO) and POPM (the copolymer of methyl methacrylate [MMA] and organically modified palygorskite), and then the composite polymer based membrane was obtained by phase-inversion method. The scanning electron microscopy results showed that the composite polymer membrane has a three-dimensional network structure. X-ray diffraction results indicated that the crystalline region of PEO is disappeared when introduction of a certain amount of the PEO. Meanwhile, the elongation of composite polymer membrane increased when increasing PEO concentration, but the value of tensile strength of PEO-POPM membrane decreased. When the mass fraction of PEO was 24%, the porosity and maximum value of ionic conductivity of the composite polymer membrane were 54% and 2.41 mS/cm, respectively. The electrochemical stability window of Li/gel composite polymer electrolyte/stainless steel batteries was close to 5.3 V (vs. Li⁺/Li), and the battery of Li/gel composite polymer electrolyte/LiFePO₄ showed good cycling performance and the discharge capacity of the battery were between 169.8 and 155 mAh/g. Meanwhile, the Coulombic efficiency of the battery maintained over 95% during the 80 cycles.     

Branched poly(biphenylene-co-sulfone)ether ion exchange membranes containing perfluorocyclobutane groups for fuel cell applications

A series of branched poly(biphenylene-co-sulfone) ion exchange membranes containing perfluorocyclobutane groups were prepared for fuel cells. Two bifunctional trifluorovinyloxy-terminated monomers (sulfonable 4,4′-bis(trifluorovinyloxy)biphenyl and insulfonable 4,4′-sulfonyl-bis(trifluorovinyloxy)biphenyl) and a trifunctional trifluorovinyloxy-terminated branching agent (1,1,1-tris(4′-trifluorovinyloxyphenyl)ethane) were synthesized and terpolymerized via thermal [2π + 2π] cyclodimerization to obtain partially fluorinated and branched polymers containing 0–5 mol% of the branching agent. They were then postsulfonated by chlorosulfonic acid at room temperature, cast as membranes, and characterized to evaluate their electrochemical properties for fuel cell applications. As the branching agent content was increased, their polydispersity values highly increased, indicating they became highly branched. It was confirmed that higher branching agent content also increased the ion exchange capacity, water uptake, and proton conductivity of the branched ion exchange membranes containing perfluorocyclobutane groups. This indicates that their electrochemical properties can be easily controlled by the degree of branching. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48373.     

Novel membranes based on poly(5‐(methacrylamido)tetrazole) and sulfonated polysulfone for proton exchange membrane fuel cells

Proton‐exchange membrane fuel cells (PEMFC)s are increasingly regarded as promising environmentally benign power sources. Heterocyclic molecules are commonly used in the proton conducting membranes as dopant or polymer side group due to their high proton transfer ability. In this study, 5‐(methacrylamido)tetrazole monomer, prepared by the reaction of methacryloyl chloride with 5‐aminotetrazole, was polymerized via conventional free radical mechanism to achieve poly(5‐(methacrylamido)tetrazole) homopolymer. Novel composite membranes, SPSU‐PMTetX, were successfully produced by incorporating sulfonated polysulfone (SPSU) into poly(5‐(methacrylamido)tetrazole) (PMTet). The sulfonation of polysulfone was performed with trimethylsilyl chlorosulfonate and high degree of sulfonation (140%) was obtained. The homopolymers and composite membranes have been characterized by NMR, FTIR, thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC). ¹H‐NMR and FTIR confirmed the sulfonation of PSU and the ionic interaction between sulfonic acid and poly(5‐(methacrylamido)tetrazole) units. TGA showed that the polymer electrolyte membranes are thermally stable up to ～190°C. Scanning electron microscopy analysis indicated the homogeneity of the membranes. This result was also supported by the appearance of a single T_g in the DSC curves of the blends. Water uptake and proton conductivity measurements were, as well, carried out. Methanol permeability measurements showed that the composite membranes have similar methanol permeability values with Nafion 112. The maximum proton conductivity of anhydrous SPSU‐PMTet0.5 at 150°C was determined as 2.2 × 10^?6 S cm^?1 while in humidified conditions at 20°C a value of 6 × 10^?3 S cm^?1 was found for SPSU‐PMTet2. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40107.     

Novel imidazole‐grafted hybrid anion exchange membranes based on poly(2,6‐dimethyl‐1,4‐phenylene oxide) for fuel cell applications

Novel organic–inorganic hybrid membranes, based on poly(2,6‐dimethyl‐1,4‐phenylene oxide), have been prepared through 1,2‐dimethylimidazole functional groups and double crosslinking agents including 3‐glycidyloxypropyltrimethoxysilane and tetraethyl orthosilicate by sol–gel process for the purpose of improving the conductivity and alkaline resistance. The structure of membranes was characterized using Fourier‐transform infrared spectra, ¹H NMR, and X‐ray diffraction. The physico‐chemical properties of all membranes were shown in ion exchange capacity, water uptake, stability, and conductivity. Membranes with OH^– conductivity up to 0.022 at 25 °C and 0.036 S cm^?1 at 80 °C. Promisingly, the chemical stability of the resulting membranes remains unchanged after storage in 2 mol dm^?3 KOH at 25 °C over at least 10 days. The tensile strength can be higher than 30 MPa, and the elongation at break (Eb) is in the range 6.68–10.84%. Hence, this hybrid membrane can be potentially applied in alkaline fuel cells. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46034.     

Montmorillonite‐reinforced sulfonated poly(phthalazinone ether sulfone ketone) nanocomposite proton exchange membranes for direct methanol fuel cells

To produce a composite membrane with high conductivity and low permeability, SPPESK with a degree of sulfonation of 101% was carefully selected for the preparation of montmorillonite (MMT)‐reinforced SPPESK using solution intercalation. The fundamental characteristics such as water uptake, swelling ratio, proton conductivity, methanol permeability, and mechanical properties of the composite membranes were studied. Water uptake is improved when organic MMT (OMMT) loading increase. The composite membranes with CTAB‐MMT loading of 4–0.5% show 0.143–0.150 S cm^?1 proton conductivity at 80°C, which approaches the value of Nafion112. In addition, methanol permeability was decreased to 6.29 × 10^?8 cm² s^?1 by the addition of 6 wt % OMMT. As a result, the SPPESK‐MMT composite membrane is a good candidate for use in direct methanol fuel cells. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39852.     

Studies on a novel anion‐exchange membrane based on chitosan and ionized organic compounds with multiwalled carbon nanotubes for alkaline fuel cells

In this work, a novel hydroxyl‐anion‐conducting membrane composed of chitosan (CTS), an ionized organic compound ([QAIM]OH), and hydroxylated multiwalled carbon nanotubes (MWCNTs‐OH) has been fabricated through a blending‐casting method assisted by a glutaraldehyde (GA) crosslinking process that can improve the mechanical properties of the membrane effectively. Fourier transform infrared spectroscopy (FTIR) and scanning electron microscopy revealed that [QAIM]OH and MWCNTs‐OH were successfully introduced into the CTS matrix. A chemical crosslinking reaction between CTS and GA could be confirmed by FTIR, X‐ray photoelectron spectroscopy, and contact angle tests. By tuning the mass fraction of [QAIM]OH and MWCNTs‐OH in the membrane, the maximum OH^? conductivity (5.66 × 10^?3 S cm^?1 at room temperature) could be achieved for the composition CTS:[QAIM]OH (1:0.75 in mass) blend doped with 3% MWCNTs‐OH. At a current density of 59.9 mA cm^?2, a membrane electrode assembly fabricated with the CTS/[QAIM]OH/ MWCNTs‐OH membrane (1:0.5/3%) achieved a power density of 31.6 mW cm^?2 in a H₂/O₂ system at room temperature. Under the condition of intermediate temperature (100–140 °C) without water, the conductivities of the membranes increased with increasing temperature and the amount of [QAIM]OH, which acted as an ionic liquid in the membrane, indicating that the ionic transport behaviors could still be occurring. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46323.     

Salt‐leaching technique for the synthesis of porous poly(2,5‐benzimidazole) (ABPBI) membranes for fuel cell application

The first instance of synthesizing porous poly(2,5‐benzimidazole) (ABPBI) membranes for high‐temperature polymer electrolyte membrane fuel cells (HT‐PEMFCs), using solvent evaporation/salt‐leaching technique, is reported herein. Various ratios of sodium chloride/ABPBI were dissolved in methanesulfonic acid and cast into membranes by solvent evaporation, followed by porogen (salt) leaching by water washing. The membranes were characterized using SEM, FTIR, TGA, and DSC. The proton conductivity, water and acid uptake of the membranes were measured and the chemical stability was determined by Fenton's test. SEM images revealed strong dependence of sizes and shapes of pores on the salt/polymer ratios. Surface porosities of membranes were estimated with Nis Elements‐D software; bulk porosities were measured by the fluid resaturation method. Thermogravimetric analysis showed enhanced dopant uptake with introduction of porosity, without the thermal stability of the membrane compromised. Incorporating pores enhanced solvent uptake and retention because of capillarity effects, enhancing proton conductivities of PEMs. Upon acid doping, a maximum conductivity of 0.0181 S/cm was achieved at 130 °C for a porous membrane compared with 0.0022 S/cm for the dense ABPBI membrane at the same temperature. Results indicated that with judicious optimization of porogen/polymer ratios, porous ABPBI membranes formed by salt‐leaching could be suitably used in HT‐PEMFCs. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45773.     

Imidazole/(HPO3)3‐doped sulfonated poly (ether ether ketone) composite membrane for fuel cells

A novel gel of imidazole/(HPO₃)₃ was synthesized and incorporated into sulfonated poly (ether ether ketone) (SPEEK) to fabricate composite proton exchange membranes. The composite membranes were characterized by alternating current impedance (AC), thermogravimetry (TG), differential scanning calorimetry (DSC), X‐ray diffraction (XRD), scanning electron microscope (SEM) and mechanical property test. Based on the electrochemical performance investigation, the proton conductivity of the membrane is intimately correlated with the temperature and the mass ratio of imidazole/(HPO₃)₃ in the composite. The SPEEK/imidazole/(HPO₃)₃?4 composite membrane (with 44.4 wt % of imidazole/(HPO₃)₃) has the optimized performance at 135°C. Mover, the strength of the composite membranes is almost comparable to that of Nafion membrane. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41946.     

Quaternized poly(2.6 dimethyl‐1.4 phenylene oxide)/polysulfone blend composite membrane doped with ZnO‐nanoparticles for alkaline fuel cells

A series of quaternized poly(2.6 dimethyl‐1.4 phenylene oxide)/polysulfone (QPPO/PSF) blend anion exchange membrane (AEM) were successfully fabricated and characterized for alkaline fuel cell application. Zinc oxide (ZnO) nanoparticles were introduced in the polymer matrix to enhance the intrinsic properties of the AEM. To confirm successful fabrication, Fourier‐transform infrared spectroscopy and nuclear magnetic resonance (¹H‐NMR) were used. The membrane properties were enhanced by the addition of ZnO nanoparticles. The addition of ZnO nanoparticles resulted to a higher ion exchange capacity (IEC) of 3.72 mmol g^?1, increase of ion conductivity (IC) up to 52.34 mS cm^?1 at 80 °C, enhancement of water uptake, and reduced methanol permeability. The QPPO/PSF/2% ZnO composite retained over 80% of its initial IC at room temperature and also retained over 50% of its initial IC at 80 °C when evaluated for alkaline stability. The maximum power output reached for the membrane electrode assembly constructed with QPPO/PSF/2%ZnO was 69 mW cm^?2 at room temperature, which is about three times more than the parent QPPO membrane. The above results indicate that QPPO/PSF/ZnO is a good candidate as an AEM for fuel cell application. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45959.     

Solution‐blown SPEEK/POSS nanofiber–nafion hybrid composite membranes for direct methanol fuel cells

This study aims to develop novel hybrid composite membranes (NHMs) by impregnating Nafion solution into the porous sulfonated poly(ether ether ketone)/polyhedral oligomeric silsesquioxanes (SPEEK/POSS) nanofibers (NFs). The composite membrane was prepared by solution blowing of a mixture of SPEEK/POSS solution. The characteristics of the SPEEK/POSS NFs and the NHMs, including morphology, thermal stability, and performance of membrane as PEMs, were investigated. The performance of NHMs was compared with that of Nafion117 and SPEEK/Nafion composite membranes. Results showed that the introduction of POSS improved the proton conductivity, water swelling, and methanol permeability of membranes. A maximum proton conductivity of 0.163 S cm^?1 was obtained when the POSS content was 6 wt % at 80°C, which was higher than that of Nafion117 and SPEEK/Nafion. NHMs could be used as proton exchange membranes (PEMs) for fuel cell applications. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42843.     

Solid‐state single‐ion conducting comb‐like siloxane copolymer electrolyte with improved conductivity and electrochemical window for lithium batteries

Achievement of high conductivity and electrochemical window at ambient temperature for an all‐solid polymer electrolyte used in lithium ion batteries is a challenge. Here, we report the synthesis and characterization of a novel solid‐state single‐ion electrolytes based on comb‐like siloxane copolymer with pendant lithium 4‐styrenesulfonyl (perfluorobutylsulfonyl) imide and poly(ethylene glycol). The highly delocalized anionic charges of ? SO₂? N^(–)? C₄F₉ have a weak association with lithium ions, resulting in the increase of mobile lithium ions number. The designed polymer electrolytes possess ultra‐low glass transition temperature in the range from ?73 to ?54 °C due to the special flexible polysiloxane. Promising electrochemical properties have been obtained, including a remarkably high conductivity of 3.7 × 10^?5 S/cm and electrochemical window of 5.2 V (vs. Li⁺/Li) at room temperature. A high lithium ion transference number of 0.80, and good compatibility with anode were also observed. These prominent characteristics endow the polymer electrolyte a potential for the application in high safety lithium ion batteries. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45848.     

Sulfonated poly(styrene)s‐PBIOO® blend membranes: Thermo‐oxidative stability and conductivity

Low‐cost polymers poly(styrene) and poly(α‐methylstyrene) have been sulfonated followed by blending with PBIOO® (30 wt % sulfonated ionomer, 70 wt % PBIOO). At this polymer ratio the sulfonated ionomer served as the macromolecular acidic cross‐linker which led to enhancement of the PBIOO stability. Both membrane types were treated with Fenton's Reagent to investigate their resistance to oxidation and radical attack. Indeed, the blend membranes showed enhanced stability in oxidative conditions compared to the pure PBIOO membranes. Furthermore, the sulfonated poly(α‐methylstyrene)‐PBIOO blend membrane showed less weight loss during and after Fenton's Test than the corresponding poly(styrene sulfonic acid)‐PBIOO membrane. Assuming all the characteristics of the blend membrane before and after the Fenton's Test, we concluded for a partial degradation of both sulfonated poly(styrene)s, whereas they remain in the blend membrane matrix due to the acid‐base crosslinking. Thus, since the sulfonated poly((α‐methyl)styrene)‐PBIOO blend membranes conserved their integrity even after Fenton's Test they can be regarded as potential low‐cost high‐T fuel cell membranes. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39889.     

Multi-cation side-chain-type containing piperidinium group poly(2,6-dimethyl-1,4-phenylene oxide) alkaline anion exchange membranes

A series of alkaline anion exchange membranes (AAEMs) based on poly(2,6-dimethyl-1,4-phenylene oxide) (PPO) with multi-cation side chain containing piperidinium group were fabricated via nucleophilic substitution and Menshutkin reaction. The chemical structures of the AAEMs (PPO-AMP-X) were determined by Fourier transform infrared and proton nuclear magnetic resonance spectra. The resultant PPO-AMP-X membranes with the ion exchange capacities (IECs) of 2.05–2.77 mmol g⁻¹ displayed the hydroxide conductivities in the range of 61.04–78.92 mS cm⁻¹ at 80°C. When tested at the same degree of functionalization levels, the PPO-AMP-X membranes exhibited significantly higher hydroxide conductivity and lower conductivity loss than conventional AAEMs bearing benzyltri-methylammonium group (PPO-TMA). The PPO-AMP-28 multi-cation membrane showed a hydroxide conductivity of 70.52 mS cm⁻¹ at 80°C, which was nearly two times higher than that of the PPO-TMA-28 single-cation membrane (36.74 mS cm⁻¹). Compared with PPO-TMA-28 (56.76% decrease), the hydroxide conductivity of PPO-AMP-28 merely decreased by 23.15% after soaked in 1 M KOH at 80°C for 500 h. Additionally, the PPO-AMP-X membranes displayed moderate mechanical properties and good thermal stabilities, which can meet the basic requirements for use in fuel cells. This study provides a facile method for preparing AAEMs with multi-cation side chain containing piperidinium group.     

Electrochemical deposition of poly[N,N′‐ethylene–bis(salicylideneiminato)–nickel(II)] nanobelts as electrode materials for supercapacitors

N,N′‐ethylene–bis(salicylideneiminato)]–nickel(II) [Ni(salen)] was synthesized in situ onto the surface of multiwalled carbon nanotubes via a one‐step potentiostatic electrodeposition as one‐dimensional nanobelts. The synthetic process was free of any templates or additives. Potential played a key role in the formation of the poly[N,N′‐ethylene–bis(salicylideneiminato)]–nickel(II)] {poly[Ni(salen)]} nanobelts, and the electrical conductivities of the poly[Ni(salen)] decreased with increasing deposition time. The capacitance values of poly[Ni(salen)] were 272, 195, and 146 F/g at 0.05 mA/cm² for deposition times of 10, 20, and 30 min, respectively. The capacitance of the sample with a particle structure was much lower than that of poly[Ni(salen)] with a nanobelt structure. The poly[Ni(salen)] nanobelts exhibited a better capacitive behavior than the poly[Ni(salen)] particles because the nanobelt structure made access for the charge and ion to the inner part of the electrode easier. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39561.     

A new sulfonated poly(ether sulfone) hybrid with low humidity dependence for high‐temperature proton exchange membrane fuel cell applications

A new sulfonated poly(ether sulfone) (PES) hybrid with low humidity dependence was prepared based on a new synthesized PES and Udel as a commercial PES. The PES was synthesized based on a pyridine containing diol which is able to change between pyridine and pyridinium salt forms during the cell performance (acidic condition) and facilitate proton transfer. The presence of nitrogen group increases inter and intramolecular interactions in the membrane and enhance proton hopping mechanism. Thermogravimetrical analysis of PES hybrid shows good thermal stability. Proton conductivity measurements were evaluated on a fuel cell test station, showing that the membrane has better performance under lower humidity (relative humidity = 60%) compare to the fully hydrated condition (relative humidity = 100%). The results reveal that proton transfer might be mainly accomplished through proton hopping mechanism at higher temperatures. The membrane also shows significant proton conductivity at 120 °C (about 6.6 mS cm^?1 at RH = 30%). © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 45342.