Batch foaming of carboxylated multiwalled carbon nanotube/poly(ether imide) nanocomposites: The influence of the carbon nanotube aspect ratio on the cellular morphology

A series of microcellular poly(ether imide) (PEI) foams and nanocellular carboxylated multiwalled carbon nanotube (MWCNT‐COOH)/PEI foams were prepared by the batch foaming method. MWCNT‐COOHs with different aspect ratios were introduced into the PEI matrix as heterogeneous nucleation agents to improve the cell morphology of the microcellular PEI foams. The effect of the aspect ratio of the MWCNT‐COOHs on the cellular morphology, and gas diffusion is discussed. The results show that with the addition of MWCNT‐COOH, the sorption curve showed a slight reduction of carbon dioxide solubility, but the gas diffusion rate could be improved. The proper aspect ratio of MWCNT‐COOH could improve the cellular morphology under the same foaming conditions, in which m‐MWCNT‐COOH (aspect ratio ≈ 1333) was the best heterogeneous nucleation agent. When the foaming temperature was 170°C, the cell size and cell density of nanocellular m‐MWCNT‐COOH reduced to 180 nm and increased to 1.58 × 10¹³ cells/cm³, respectively. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42325.     

Simple and feasible strategy to fabricate microcellular poly(butylene succinate) foams by chain extension and isothermal crystallization induction

In this article, a facile and efficient isothermal crystallization induction method was proposed to fabricate microcellular poly(butylene succinate) (PBS) foams with supercritical CO₂. The good regularity of PE chain segments and high reactive epoxy groups in ethylene-glycidyl methacrylate copolymer (PE-g-GMA) serving as a chain extender were employed to improve the crystallization behaviors, viscoelasticity, and foaming behaviors of PBS through chain extension reaction. The effect of PE-g-GMA content on the thermal properties, rheological performances, and cellular morphology of various PBS samples was investigated systematically. When the PE-g-GMA content switched from 7.5 to 10 wt %, an interesting transition from fine cells to microcells was observed in PBS/PE-g-GMA foams. Microcellular PBS foam modified by 10 wt % PE-g-GMA was successfully prepared at the foaming temperature of 87 °C and the induction time of 7 min, in which its cell size and cell density could reach 6.63 ± 1.93 μm and 3.75 × 10⁹ cells cm⁻³, respectively. The formation of abundant but tiny spherocrystals in chain extended PBS samples made a considerable contribution for preparing microcellular PBS foams. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48850.     

Open‐cell foams of polyethylene terephthalate/bisphenol a polycarbonate blend

Open microcellular foams of polyethylene terephthalate (PET)/polycarbonate (PC) blends were prepared by controlling their foaming behavior at the interface between these two polymers. Interface modification was a crucial factor in governing the foaming behavior and cell morphology of the blend foams: annealing at 280°C, i.e., conducting the transesterification reaction, generates a PET‐b‐PC copolymer, which lowers the interfacial tension, increases the affinity between PET and PC, and decreases the crystallinity of the PET domains. When CO₂ foaming was performed at the interface modified with the copolymer, an interesting fibril‐like structure was formed. The cell density of the PET/PC blend then increased, and its cell size reduced to the microscale while maintaining a high open‐cell ratio. The effect of heat annealing (transesterification reaction) on CO₂‐foaming was studied to reveal the relationship among the interface affinity, crystallinity, and degree of fibrillation. The optimal heat‐annealing procedure generated a fibril‐like structure in the PET/PC blend foams with a high cell density (7 × 10¹¹ cm^?3), small cell size (less than 2 μm), and 100% open‐cell ratio. POLYM. ENG. SCI., 55:375–385, 2015. © 2014 Society of Plastics Engineers     

Cell morphology and mechanical properties of microcellular mucell® injection molded polyetherimide and polyetherimide/fillers composite foams

Microcellular polyetherimide (PEI) foams were prepared by microcellular injection molding using supercritical nitrogen (SC‐N₂) as foaming agent. The effects of four different processing parameters including shot size, injection speed, SC‐N₂ content, and mold temperature on cell morphology and material properties were studied. Meanwhile, multiwalled carbon nanotube (MWCNT), nano‐montmorillonoid (NMMT), and talcum powder (Talc) were introduced into PEI matrix as heterogeneous nucleation agents in order to further improve the cell morphology and mechanical properties of microcellular PEI foams. The results showed that the processing parameters had great influence on cell morphology. The lowest cell size can reach to 18.2 μm by optimizing the parameters of microcellular injection molding. Moreover, MWCNT can remarkably improve the cell morphology of microcellular PEI foams. It was worth mentioning that when the MWCNT content was 1 wt %, the microcellular PEI/MWCNT foams displayed optimum mechanical properties and the cell size decreased by 28.3% compared with microcellular PEI foams prepared by the same processing parameters. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 4171–4181, 2013     

Microcellular foams of glass–fiber reinforced poly(phenylene sulfide) composites generated using supercritical carbon dioxide

Microcellular foaming of poly(phenylene sulfide) (PPS) and its glass–fiber (GF) reinforced composites using supercritical CO₂ as a blowing agent presents a promising approach to produce novel cellular materials with tailored microstructures. This study investigated the effects of the material composition and process conditions on the foaming behaviors and final morphologies of the microcellular foamed PPS and PPS/GF composites. The rheological and thermal properties as well as the saturation and desorption behaviors of CO₂ in the pure PPS and PPS/GF composites were also detailedly discussed. The results show that microcellular foams with various relative densities, cell sizes, cell‐size distributions, and cell densities can be attained by tailoring the fiber content and key process parameters. At low foaming temperatures below the cold crystallization temperature, the microcellular foamed PPS and PPS/GF composites both present a unimodal cell‐size distribution. At elevated temperatures, the generated crystalline superstructures including spherulites in the polymer matrix and transcrystals around the GF will cause a secondary heterogeneous cell nucleation. This leads to the observations of bimodal and trimodal cell‐size distributions in the pure PPS and the PPS/GF composites, respectively. The mechanisms for the solid‐state foaming behaviors of pure PPS and PPS/GF composites have been illustrated by establishing theoretical models. POLYM. COMPOS., 37:2527–2540, 2016. © 2015 Society of Plastics Engineers     

Microstructure and Properties of Microcellular Poly (phenylene sulfide) Foams by Mucell Injection Molding

A series of microcellular poly (phenylene sulfide) (PPS) foams were prepared by Mucell injection molding. The cell structure, mechanical properties, crystallization behavior and dielectric property of microcellular PPS foams were systemically investigated. The results showed that the longer the length of flow passage of injection mold, the larger cell size of microcellular PPS foams. The injection parameter of shot size played an important role in relative density of microcellular PPS foams. When the relative density of microcellular PPS foam reached to 0.658, the tensile strength, flexural strength and impact strength of PPS foam materials achieved 10.82 MPa, 52.99 MPa and 0.305 J/cm², respectively. Meanwhile, with the relative density decreasing, the dielectric constant of PPS foam materials reduced, while the volume resistivity of its uprated.     

Extrusion of polystyrene nanocomposite foams with supercritical CO2

Intercalated and exfoliated polystyrene/nano‐clay composites were prepared by mechanical blending and in situ polymerization respectively. The composites were then foamed by using CO₂ as the foaming agent in an extrusion foaming process. The resulting foam structure is compared with that of pure polystyrene and polystyrene/talc composite. At a screw rotation speed of 10 rpm and a die temperature of 200°C, the addition of a small amount (i.e., 5 wt%) of intercalated nano‐clay greatly reduces cell size from 25.3 to 11.1 μm and increases cell density from 2.7 × 10⁷ to 2.8 × 10⁸ cells/cm³. Once exfoliated, the nanocomposite exhibits the highest cell density (1.5 × 10⁹ cells/cm³) and smallest cell size (4.9 μm) at the same particle concentration. Compared with polystyrene foams, the nanocomposite foams exhibit higher tensile modulus, improved fire retardance, and better barrier property. Combining nanocomposites and the extrusion foaming process provides a new technique for the design and control of cell structure in microcellular foams.     

Effects of clay dispersion on the foam morphology of LDPE/clay nanocomposites

Intercalated and exfoliated low‐density polyethylene (LDPE)/clay nanocomposites were prepared by melt blending with and without a maleated polyethylene (PE‐g‐MAn) as the coupling agent. Their morphology was examined and confirmed by X‐ray diffraction (XRD) and transmission electron microscopy (TEM). The effects of clay content and dispersion on the cell morphology of nanocomposite foams during extrusion foaming process were also thoroughly investigated, especially with a small amount of clay of 0.05–1.0 wt%. This research shows the optimum clay content for achieving microcellular PE/clay nanocomposite foams blown with supercritical CO₂. It is found that < 0.1 wt% of clay addition can produce the microcellular foam structure with a cell density of > 10⁹ cells/cm³ and a cell size of ～ 5 μm. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 2129–2134, 2007     

Preparation of microcellular poly(ethylene‐co‐octene) rubber foam with supercritical carbon dioxide

In the past 3 decades, there has been great advancement in the preparation of microcellular thermoplastic polymer foams. However, little attention has been paid to thermoplastic elastomers. In this study, microcellular poly(ethylene‐co‐octene) (PEOc) rubber foams with a cell density of 2.9 × 10¹⁰ cells/cm³ and a cell size of 1.9 μm were successfully prepared with carbon dioxide as the physical blowing agent with a batch foaming process. The microcellular PEOc foams exhibited a well‐defined, closed‐cell structure, a uniform cell size distribution, and the formation of unfoamed skin at low foaming temperatures. Their difference from thermoplastic foam was from obvious volume recovery in the atmosphere because of the elasticity of the polymer matrix. We investigated the effect of the molecular weight on the cell growth process by changing the foaming conditions, and two important effect factors on the cell growth, that is, the polymer matrix modulus/melt viscoelastic properties and gas diffusion coefficient, were assessed. With increasing molecular weight, the matrix modulus and melt viscosity tended to increase, whereas the gas solubility and diffusion coefficient decreased. The increase in the matrix modulus and melt viscosity tended to decrease the cell size and stabilize the cell structure at high foaming temperatures, whereas the increase in the gas diffusion coefficient facilitated cell growth at the beginning and limited cell growth because most of the gas diffused out of the polymer matrix during the long foaming times or at high foaming temperatures. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Effect of solvent plasticization on polypropylene microcellular foaming process and foam characteristics

In this research, the effect of crystalline fraction of polypropylene (PP) on cell nucleation behavior was overcome by an introduction of solvent‐plasticized step to the microcellular foaming in a solid‐state batch‐foaming process. Utilizing the plasticization performance of the solvent facilitated the PP to be foamed at the temperatures lower than its melting point with the dramatic development in the cellular morphology of the final foams. In consequence of the heterogeneous cell nucleation sites induction and the crystalline loss, which were induced by solvent, a high cell density (i.e., 10⁹–10¹⁰ cells/cm³) was promoted without the cell sacrificing at the elevated temperatures (155 and 165°C) and favorable PP microcellular foams were accomplished. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Solid‐state microcellular high temperature vulcanized (HTV) silicone rubber foam with carbon dioxide

A series of microcellular high temperature vulcanized (HTV) silicone rubber foams were prepared using CO₂ as a physical blowing agent. Rheological properties, gas diffusive behavior, and foaming parameters of silicone rubber were investigated. The results show that saturation pressure has a significant effect on the diffusivity of CO₂ in HTV silicone rubber matrix. The gas concentration and diffusivity increase from 2.45 wt % to 3.24 wt %, and from 1.62 × 10^?5 cm²/s to 7.83 × 10^?5 cm²/s as the saturation pressure increases from 2 MPa to 5 MPa, respectively. The value of the gas diffusivity in HTV silicone rubber is almost 1000 times higher than that of the gas diffusivity in polyetherimide (PEI) matrix. Additionally, microcellular HTV silicone rubber foams with the smallest cell diameter of 9.8 μm and cell density exceeding 10⁸ cells/cm³ are achieved. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 44807.     

Effect of die temperature on the morphology of microcellular foams

A study on the extrusion of microcellular polystyrene foams at different foaming temperatures was carried out using CO₂ as the foaming agent. The contraction flow in the extrusion die was simulated with FLUENT computational fluid dynamics code at two temperatures (150°C and 175°C) to predict pressure and temperature profiles in the die. The location of nucleation onset was determined based on the pressure profile and equilibrium solubility. The relative importance of pressure and temperature in determining the nucleation rate was compared using calculations based on classical homogeneous nucleation theory. Experimentally, the effects of die temperature (i.e., the foaming temperature) on the pressure profile in the die, cell size, cell density, and cell morphology were investigated at different screw rotation speeds (10 ～ 30 rpm). Experimental results were compared with simulations to gain insight into the foaming process. Although the foaming temperature was found to be less significant than the pressure drop or the pressure drop rate in deciding the cell size and cell density, it affects the cell morphology dramatically. Open and closed cell structures can be generated by changing the foaming temperature. Microcellular foams of PS (with cell sizes smaller than 10 μm and cell densities greater than 10 cells/cm³) are created experimentally when the die temperature is 160°C, the pressure drop through the die is greater than 16 MPa, and the pressure drop rate is higher than 10⁹ Pa/sec.     

Ethylene–propylene‐diene terpolymer/halloysite nanocomposites: Thermal,mechanical properties,and foam processing

Ethylene–propylene‐diene terpolymer (EPDM)/halloysite nanotube (HNT) nanocomposites were prepared by melt mixing in an internal mixer using a commercially available maleated semicrystalline EPDM and HNT. Transmission electron microscopy analysis of the EPDM/HNT composites revealed that the HNTs are uniformly dispersed at a nanometer scale in the matrix. Differential scanning calorimeter studies indicated that the HNT caused an increase in the nonisothermal crystallization temperature of the EPDM. Tensile and dynamic mechanical analysis exhibited that a small amount of the HNTs effectively enhanced the stiffness of the EPDM without adversely affecting its elongation‐at‐break. The EPDM/HNT nanocomposites were used to produce foams by using a batch process in an autoclave, with supercritical carbon dioxide as a foaming agent. The nanocomposite foams showed a smaller cell size and higher cell density as compared to the neat EPDM foam, and the nanocomposite with 10 phr HNT produced a microcellular foam with average cell size as small as 7.8 μm and cell density as high as 1.5 × 10¹⁰ cell/cm³. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40307.     

Role of chain extension in the rheological properties,crystallization behaviors,and microcellular foaming performances of poly (butylene adipate-co-terephthalate)

Currently, the fabrication of microcellular semicrystalline polymer foam using supercritical CO₂ as a blowing agent constitutes a worldwide interest. In this work, a facile approach of chain extension and batch foaming was proposed to prepare microcellular semicrystalline poly (butylene adipate-co-terephthalate) (PBAT) foam using CO₂ as a physical blowing agent. With the introduction of chain extender (CE), the weight-average molecular weight and gel fraction of PBAT samples increased; their crystallization temperature increased from 74.2 to 86.9 °C and their viscoelasticity was improved greatly. Microcellular PBAT foams with the cell size <4 μm and the cell density more than 10¹⁰ cells cm⁻³ were fabricated successfully. With increasing concentration of CE, the cell density and volume expansion ratio (VER) of various PBAT foams increased from 3.4 × 10¹⁰ to 8.7 × 10¹⁰ cells cm⁻³ and from 1.5 to 2.0 times, respectively. With increasing foaming temperature, the cell size and VER increased and the cell density decreased. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47322.     

Influence of crystallization on microcellular foaming behavior of polyamide 6 in a supercritical CO2-assisted route

Supercritical CO₂ as a blowing agent has attracted increasing interest in the preparation of microcellular polyamide 6 (PA6) foams. In this work, we developed the supercritical CO₂-assisted method to prepare a series of different microcellular PA6 foams by controlling its crystallization properties in two steps and carefully investigated the corresponding crystallization properties of modified PA6 and foams using various techniques. Initially, a multifunctional epoxy-based chain extender (CE) was used to produce high-melt strength-modified PA6 with improved foaming ability; then, the resulting PA6 was foamed to prepare the microcellular foams of PA6 using supercritical CO₂ as a blowing agent in a batch foaming route. The CE effectively enhanced the melt strength of PA6, and CE usage was optimized to obtain a threshold of high branching without crosslinking. The number of crystals was also adjusted by the saturation temperature. Furthermore, these crystals that formed during the saturation process served as high-efficiency bubble nucleating agents and then limited the growth of bubbles at the same time. The microcellular foams of PA6 were successfully obtained with a cell size of 10.0 μm, and cell density of 2.0 × 10⁹ cells/cm³ at the saturation temperature of 225°C.     

Fabrication of polystyrene/nano‐CaCO3 foams with unimodal or bimodal cell structure from extrusion foaming using supercritical carbon dioxide

The article surveyed the fabrication of polystyrene (PS)/nano‐CaCO₃ foams with unimodal or bimodal cellular morphology from extrusion foaming using supercritical carbon dioxide (sc‐CO₂). In order to discover the factors influenced the cell structure of PS/nano‐CaCO₃ foams, the effects of die temperature, die pressure, and nano‐CaCO₃ content on cell size, density, and morphology were investigated detailed. The results showed that the nano‐CaCO₃ content affected the cell size and morphology of PS/nano‐CaCO₃ foams significantly. When the die temperature and pressure was 150°C and 18 MPa, respectively, the foams with 5 wt% nano‐CaCO₃ exhibited the unimodal cellular morphology. As the nano‐CaCO₃ content increased to 20 wt%, a bimodal cell structure of the foams could be obtained. Moreover, it was found that the bimodal structure correlated more strongly with the pressure drop than the foaming temperature. The article revealed that unimodal or bimodal cellular morphology of PS/nano‐CaCO₃ foams could be achieved by changing the extrusion foaming parameters and nano‐CaCO₃ content. POLYM. COMPOS., 37:1864–1873, 2016. © 2015 Society of Plastics Engineers     

Fabrication and cell morphology of a microcellular poly(ether imide)–carbon nanotube composite foam with a three-dimensional shape

The preparation of microcellular poly(ether imide) (PEI) based foams with three-dimensional geometry remains a great challenge worldwide. In this study, we fabricated microcellular PEI–carbon nanotube (CNT) bead foams with a batch rapid depressurization method in a self-designed mold with supercritical carbon dioxide (scCO₂) as a blowing agent. The effects of the saturation time, foaming temperature, foaming pressure, and depressurization rate on the microcellular structures of the PEI foam were analyzed by the Taguchi approach to determine the optimum foaming conditions, and the influence of the CNT content on the cell structure was analyzed. The results show that the depressurization rate and foaming temperature were the key factors influencing the cell size and cell density (N _f); that is, the high depressurization rate and low foaming temperature favored a small cell size and high N _f. The foaming temperature also influenced the foaming ratio (ϕ), and a high ϕ was obtained at a high foaming temperature. Under optimal foaming conditions, PEI with 2.0 wt % CNTs presented the best cell structure; N _f, cell size, and ϕ were 6.14 × 10¹⁰ cell/cm³, 2.43 μm, and 2.08, respectively. The mechanical properties of the final parts were related more to the foaming time and CNT concentration, and the maximum tensile and compression strength were reached at 3 h foaming time and 2.0 wt % CNT, that is, at 2.75 and 15.1 MPa (10% strain), respectively. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47501.     

The effect of nanoclay on the crystallization behavior,microcellular structure,and mechanical properties of thermoplastic polyurethane nanocomposite foams

The effects of nanoclay on the crystallization behavior, microcellular structure, and mechanical properties of thermoplastic polyurethane (TPU)/clay nanocomposite (TPUCN) foams were investigated using differential scanning calorimetry, rheometry, scanning electron microscope, transmission electron microscopy, and X‐ray diffraction. It was found that the nanoclay acted as an effective nucleating agent for both crystal nucleation and cell nucleation. As a result, it significantly enhanced the crystallization behavior of the hard segment (HS) domains in TPU while refining the foamed structure of the microcellular injection molded parts. In particular, the average cell diameter of TPUCN foams decreased from 45 µm for neat TPU to 27 µm for TPUCN5 (5 wt% clay) and 18 µm for TPUCN10 (10 wt% clay). Furthermore, the cell density increased from 0.7 × 10⁷ cell/cm³ for neat TPU to 1.4 × 10⁷ cell/cm³ and 3.1 × 10⁷ cell/cm³ for TPUCN5 and TPUCN10, respectively. In addition, the tensile strength also increased by 56.3% and 89.2% with 5 and 10 wt% clay content, respectively. By controlling the cell nucleation behavior through uniformly dispersed nanoclay, this study demonstrates that it is feasible to produce TPUCN foams via microcellular injection molding with desirable microcellular structures and improved mechanical properties. POLYM. ENG. SCI., 56:319–327, 2016. © 2015 Society of Plastics Engineers     

Microcellular foaming of low‐density polyethylene using nano‐CaCo3 as a nucleating agent

In this study, microcellular foaming of low‐density polyethylene (LDPE) using nano‐calcium carbonate (nano‐CaCO₃) were carried out. Nanocomposite samples were prepared in different content in range of 0.5–7 phr nano‐CaCO₃ using a twin screw extruder. X‐ray diffraction and scanning electron microscopy (SEM) were used to characterize of LDPE/nano‐CaCO3 nanocomposites. The foaming was carried out by a batch process in compression molding with azodicarbonamide (ADCA) as a chemical blowing agent. The cell structure of the foams was examined with SEM, density and gel content of different samples were measured to compare difference between nanocomposite microcellular foam and microcellular foam without nanomaterials. The results showed that the samples containing 5 phr nano‐CaCO₃ showed microcellular foam with the lowest mean cell diameter 27 μm and largest cell density 8 × 10⁸ cells/cm³ in compared other samples. POLYM. COMPOS., 2011. © 2011 Society of Plastics Engineers     

Microcellular foaming of poly(phenylene sulfide)/poly(ether sulfones) blends using supercritical carbon dioxide

Microcellular foaming of poly(phenylene sulfide)/poly(ether sulfones) (PPS/PES) blends presents a promising approach to produce high‐performance cellular materials with tailored microstructures and enhanced properties. This study investigated the effects of multiphase blend composition and process conditions on the foaming behaviors and final cellular morphology, as well as the dynamic mechanical properties of the solid and microcellular foamed PPS/PES blends. The microcellular materials were prepared via a batch‐foam processing, using the environment‐friendly supercritical CO₂ (scCO₂) as a blowing agent. The saturation and desorption behaviors of CO₂ in PPS/PES blends for various blend ratios (10 : 0, 8 : 2, 6 : 4, 5 : 5, 4 : 6, 2 : 8, and 0 : 10) were also elaborately discussed. The experimental results indicated that the foaming behaviors of PPS/PES blends are closely related to the blend morphology, crystallinity, and the mass‐transfer rate of the CO₂ in each polymer phase. The mechanisms for the foaming behaviors of PPS/PES blends have been illustrated by establishing theoretical models. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42634.