Oxidative graft polymerization of aniline on the modified surface of polypropylene films

A novel method for preparing electrically conductive polypropylene‐graft‐polyacrylic acid/polyaniline (PP‐g‐PAA/PANI) composite films was developed. 1,4‐Phenylenediamine (PDA) was introduced on the surface of PP‐g‐PAA film, and then, chemical oxidative polymerization of aniline on PP‐g‐PAA/PDA film was carried out to prepare PP‐g‐PAA/PANI electrically conductive composite films. After each step of reaction, the PP film surface was characterized by attenuated total reflectance Fourier transform infrared spectroscopy. Static water contact angles of the PP, PP‐g‐PAA, and PP‐g‐PAA/PANI films were measured, and the results revealed that graft reactions took place as expected. The morphology of the PP‐g‐PAA film and the PP‐g‐PAA/PANI composite film were observed by atomic force microscopy. The conductivity and the thickness of the PP‐g‐PAA/PANI composite films with 1.5 wt % PANI were around 0.21 S/cm and 0.4 μm, respectively. The PANI on the PP‐g‐PAA/PANI film was reactivated and chain growing occurred to further improve the molecular weight of PANI. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 2442–2450, 2007     

Influences of degradability,bioactivity, and biocompatibility of the calcium sulfate content on a calcium sulfate/poly(amino acid) biocomposite for orthopedic reconstruction

The inorganic content in a bioceramic/polymer composite is considered to play an important role in promoting bone healing after implantation in vivo. In this study, two calcium sulfate/poly(amino acid) (CS/PAA) composites with CS content proportions of 50% (mass fraction, 50CS/PAA) and 65% (65CS/PAA) were synthesized via the in situ melting polymerization method, and the degradability, bioactivity, and biocompatibility of the composites were evaluated. The results indicated that 41.5% of weight loss of the 50CS/PAA was observed after soaking in simulated body fluid (SBF) for 16 weeks, whereas 56.2% of weight loss of the 65CS/PAA was observed. These results suggested that the CS content in the composite affected the degradability of the composite. After being soaked in SBF for 1 week, formation of an apatite layer was observed on the surfaces of both composites without obvious differences. The co‐culture results of the composites and the MG‐63 cells confirmed that 65CS/PAA exhibited higher proliferation and a higher alkaline phosphatase (ALP) activity than did 50CS/PAA. The implantations in bone defects of rabbits for 3 months revealed that both composites had good biocompatibility and were capable of guiding new bone formation without causing any inflammation. However, faster degradability of the 65CS/PAA composite was observed in vivo, indicating that the higher CS content in the composite results in higher degradability. In conclusion, the CS content in the composite for orthopedic reconstruction has distinct effects on the degradability, OD value, and ALP activity of the composites, whereas it has little effect on the bioactivity and bone formation. POLYM. COMPOS., 37:1886–1894, 2016. © 2015 Society of Plastics Engineers     

Influence of potassium humate on the swelling properties of a poly(acrylic acid‐co‐acrylamide)/ potassium humate superabsorbent composite

A novel superabsorbent composite, poly(acrylic acid‐co‐acrylamide)/potassium humate (PAA‐AM/KHA), was prepared by aqueous solution polymerization from acrylic acid, acrylamide, and potassium humate (KHA) with N,N′‐methylenebisacrylamide as a crosslinker and potassium peroxydisulfate as an initiator. The effects of incorporated KHA on the water absorbency, swelling rate, and reswelling capability were investigated. The swelling property of PAA‐AM/KHA in various saline solutions was studied systematically. The results show that the comprehensive properties and especially salt‐resistant ability of PAA‐AM/KHA were enhanced. There was a linear relationship between the saturated water absorbency and the minus square root of the ionic strength of the external medium, and the water absorbency of PAA‐AM/KHA in various salt solutions had the following order: NH₄Cl_(aq) = KCl_(aq) = NaCl_(aq) > MgCl_2(aq) > CaCl_2(aq) > AlCl_3(aq) > FeCl_3(aq). Moreover, the polymeric net structure of PAA‐AM/KHA was examined with respect to that of poly(acrylic acid‐co‐acrylamide). The results indicate that the polymeric net of PAA‐AM/KHA was improved by the introduction of a moderate amount of KHA into the superabsorbent composite and made more suitable for agriculture and horticulture applications. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

Preparation of hybrid composite microspheres containing nanosilicon via microsuspension polymerization

Hybrid composite microspheres with nano‐Si as the core and poly(styrene‐co‐acrylonitrile) as a shell are successfully prepared by a two‐step polymerization technique, which includes dispersion polymerization of styrene and 3‐methacryloxypropyl trimethoxysilane in ethanol for surface modification of nano‐Si followed by microsuspension polymerization of styrene and acrylonitrile in an aqueous phase for encapsulating nano‐Si into an SAN copolymer matrix. The structure and surface properties of modified nano‐Si are investigated by Fourier transform infrared spectroscopy (FTIR) and contact angle. The hybrid composite microspheres are systematically characterized by energy dispersive spectroscopy, thermogravimetric analysis, and transmission electron microscopy (TEM). According to the FTIR spectra and the contact angle experiments, it was determined that a hydrophobic polymer layer was formed on the surface of nano‐Si. TEM showed that nano‐Si was homogeneously dispersed in SAN particles when the loading capacity of nano‐Si in the hybrid composite microspheres was less than 20 wt %. Moreover, scanning electron microscopy and X‐ray photoelectron spectroscopy revealed that there were large amounts of nano‐Si absorbed on the surface of the hybrid composite microspheres, and the mean particle size became much larger when the loading amounts of nano‐Si reached 25 wt %. From this, it can be inferred that nano‐Si overflows from the inner core to the outside surface in the emulsification process and acts as an inorganic dispersant. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43101.     

Swelling behavior and pervaporation properties of new composite membrane systems: Porous polyethylene film‐poly(acrylic acid) hydrogel

A new type of composite membrane for pervaporation has been developed. These membranes were prepared by free‐radical copolymerization of acrylic acid with a macromolecular polyfunctional crosslinker (allylhydroxyethylcellulose) inside the porous polyethylene (PE) film. It was shown that the porous structure of the PE matrix is filled with poly(acrylic acid) (PAA), and a layer of acid is formed on the film surface. To investigate the effect of the porous matrix on the composite membrane properties, a hydrogel membrane of crosslinked PAA was also prepared without the matrix using the same procedure. PAA in both membranes was in the neutralized form (K⁺). Swelling behavior of the membranes and their separation characteristics for pervaporation were investigated in water–ethanol solutions depending on the ethanol concentration. All membranes exhibited a high degree of equilibrium swelling (Q = 20–50 g/g) in dilute ethanol solutions (0–30 vol %), and Q sharply dropped to 1.5–2 g/g at a EtOH concentration of 30–40 vol % due to collapse of the gel. All membranes under study were highly permeable and selective to water over a wide range of ethanol concentrations in the feed (50–96 vol %), but composite membranes had a higher separation factor due to the restriction effect of the matrix porous structure on swelling of PAA(K⁺) inside the pores. However, composite membranes were characterized by a lower permeation rate, compared to the crosslinked PAA membranes without a matrix, because of their lower effective surface for diffusion. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 1461–1465, 2004     

Chemical‐vapor‐sensitive materials based on a multiwalled carbon nanotube/hydroxyl propyl methylcellulose/cellulose composite

A type of chemical vapor‐sensing material made from multiwalled carbon nanotubes/hydroxyl propyl methyl cellulose/cellulose composite films were prepared in the room‐temperature ionic liquid 1‐butyl‐3‐methylimidazolium chloride ([BMIm]Cl). A typical negative vapor coefficient was observed when the film was placed in polar organic solvents, such as methanol and ethanol. The sensitivity of the film to vapors increased significantly with increasing temperature. Interestingly, the resistance of the films increased almost linearly with decreasing vacuum, and the changes in resistance with the vacuum show good repeatability. The surface morphology, thermostability, and stress–strain properties of the composite films were analyzed with scanning electron microscopy, thermogravimetric analysis, and an electrical universal testing machine, respectively. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41639.     

Effect of attapulgite contents on release behaviors of a pH sensitive carboxymethyl cellulose‐g‐poly(acrylic acid)/attapulgite/sodium alginate composite hydrogel bead containing diclofenac

A series of pH‐sensitive composite hydrogel beads, carboxymethyl cellulose‐g‐poly(acrylic acid)/attapulgite/sodium alginate (CMC‐g‐PAA/APT/SA), were prepared by combining CMC‐g‐PAA/APT composite and SA, using Ca²⁺ as the ionic crosslinking agent and diclofenac sodium (DS) as the model drug. The effects of APT content and external pH on the swelling properties and release behaviors of DS from the composite hydrogel beads were investigated. The results showed that the composite hydrogel beads exhibited good pH‐sensitivity. Introducing 20% APT into CMC‐g‐PAA hydrogel could change the surface structure of the composite hydrogel beads, decrease the swelling ability, and relieve the burst release effect of DS. The drug cumulative release ratio of DS from the hydrogel beads in simulated gastric fluid was only 3.71% within 3 hour, but in simulated intestinal fluid about 50% for 3 hour, 85% for 12 hour, up to 90% after 24 hour. The obtained results indicated that the CMC‐g‐PAA/APT/SA hydrogel beads could be applied to the drug delivery system as drug carriers in the intestinal tract. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Evaluation of the etching and chrome plating on the ABS,PVC, and PVC/ABS blends surface

As replacement for acrylonitrile‐butadiene‐styrene (ABS), which is commonly used in the manufacture of chrome parts, polyvinyl chloride (PVC) and PVC/ABS blend parts were produced by injection process, etched in sulfochromic solution in different concentrations, immersion time, and temperature, and they were subsequently chrome‐plated by conventional method. After etching, the sample surfaces were analyzed by Scanning Electron Microscopy (SEM), Atomic Force Microscopy (AFM), roughness, and contact angle, and compared with the ABS surface. The metal deposition was assessed by visual inspection and adhesion test. The roughness influenced the adhesion of the metal layer directly. The chemical etching increased the surface wettability. To achieve a good metal layer adhesion, higher temperatures, immersion time, and etching solution concentration were necessary. A concentration of 350 g/L chromic acid and 400 g/L sulfuric acid, a 70 °C temperature and a 15 min immersion time resulted in good adhesion in PVC and PVC/ABS blends. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44571.     

Preparation and monovalent selective properties of multilayer polyelectrolyte modified cation‐exchange membranes

This study reports the modification of commercial cation‐exchange membrane by layer‐by‐layer adsorption of polyethyleneimine and poly(acrylic acid) (PAA) to endow them with monovalent ion selectivity. The chemical and morphological changes of the modified membrane surface were examined by ATR‐FTIR and SEM, respectively. The permselectivity for monovalent cations of the membranes was investigated by electrodialysis experiments. The effects of deposited bilayer number, the salt concentration, and pH of the dipping polyelectrolyte solutions on selectivity were investigated. Meanwhile, the resistance of membranes was measured taking energy consumption into consideration. The polyelectrolyte multilayer was crosslinked using epichlorohydrin to improve stability, and the durability of the composite membrane was studied. Separation mechanism of the composite membrane was also investigated. It is demonstrated that the bivalent cations are mainly rejected by electrostatic repulsion from the positive charge on the surface of the composite membranes. The sieving effect of the dense structure of skin layer becomes more pronounced with the number of deposited layers increased. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41488.     

Surface modification of textile material through deposition of regenerated silk fibroin

Regeneration of silk fibroin from calcium chloride/ethanol/water solution is of high interest to shape biomaterial based products for medical and technical application. In this study a continuous process for surface modification of cellulose or polyamide fibers by regenerated fibroin deposits has been investigated. The decomposition of the fibroin‐calcium complex was initiated by addition of K₂CO₃ followed by a methanol rinse. Reactive Blue 19 labeled fibroin was used to monitor the deposition of fibroin on the substrates by colour measurement. The fibroin deposits on the fabric were characterized by microscopy, N‐content, calcium, and protein content. Stiffness and surface resistivity of modified fabrics were determined as representative physical parameters. The reduced mobility of fibers increased fabric stiffness. Surface resistivity of treated samples was reduced by a factor of 10 to 100, which gives an example for the potential of the technique as coating for man‐made fiber textiles. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45098.     

Synthesis of poly(AA‐co‐AM) superabsorbent composites by reinforcement of halloysite nanotubes

A novel poly(acrylic acid‐co‐acrylamide)/halloysite nanotubes [PAA‐AM/HNTs] superabsorbent composite was synthesized by free radical polymerization with using HNTs as an inorganic additive. The composite was characterized by Fourier transform infrared spectroscopy, scanning electron microscope, and thermogravimetric analysis. The results revealed that HNTs and PAA‐AM were combined well together to form a porous structure with a pore size of about 10 μm, and HNTs were uniformly distributed in the composite. The thermal stability was improved by adding HNTs in the composite. The influences of contents of initiator and halloysite, neutralization degree of AA, and molar ratio of AM to AA on water absorbency were investigated. The water absorbency and the water retention capacity were improved after adding HNTs into PAA‐AM. The composite containing 10% HNTs had the highest water absorbency of 1276 g/g in distilled water. Moreover, PAA‐AM/HNTs composite also had a high swelling rate within 60 min and could maintain 78% initial swelling capability after five reswelled test. The substantial enhancement of swelling properties enables PAA‐AM/HNTs suitable for numerous practical applications. POLYM. COMPOS., 36:229–236, 2015. © 2014 Society of Plastics Engineers     

Preparation of Platinum‐Poly(O‐dihydroxybenzene) Composite Catalyst and Its Electrocatalytic Activity Toward Methanol and Formic Acid Oxidation

A composite catalyst has been successfully prepared by dispersing Pt nanoparticles on a poly(o‐dihydroxybenzene) (PoDHB) modified glassy carbon (GC) electrode and characterized by SEM, EDX, and electrochemical analysis. Compared with Pt nanoparticles deposited on the bare GC, the Pt/PoDHB/GC exhibits higher catalytic activity and stronger poisoning tolerance for electro‐oxidation of methanol and formic acid. The enhanced performance could be attributed to the increase of electrochemical active surface area (EASA) arisen from the PoDHB modification. Furthermore, performance limiting factors such as platinum loading, polymer mass, H₂SO₄, methanol, and formic acid concentrations have been evaluated for optimizing the electrocatalytic activities.     

Polyaniline/silver/cerium nitrate ternary composite: Synthesis,characterization and enhanced electrochemical properties

Polyaniline/Ag/Ce (NO₃)₃ ternary composites were prepared by in situ polymerization in a poly (2‐arcylamido‐2‐methylpropane sulfonic acid) aqueous solution. Fourier transform infrared spectroscopy and Ultraviolet‐visible spectroscopy analyses indicated that Ce ions had a conjugated interaction with N, O of polyaniline (PANI), and poly (2‐arcylamido‐2‐methylpropane sulfonic acid). By comparison with PANI and PANI binary composite, this ternary composite had a better thermal stability, a high conductivity (3.49 S/cm), a large capacitance, and a high electrochemical activity. Especially, the corrosion potential of this ternary composite can reach ?418 mV and the inhibition efficiency can be increased by 68.08%. This ternary porous composite has promising applications in capacitor, conductive materials, anticorrosion coating, and other related fields. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42785.     

Synthesis of 2H‐Thiopyrans by Rhodium(II) Acetate‐Catalyzed Reaction of 4‐Amino‐2,5‐dihydro‐3‐thiophenecarbonitriles with α‐Diazocarbonyl Compounds. Part 1

4‐Amino‐2,5‐dihydro‐3‐thiophenecarbonitriles 1 reacted with dimethyl diazomalonate in the presence of rhodium(II) acetate to give regioselectively 4‐cyano‐2H‐thio‐pyrans 2 (C ₂— S insertion), and 5‐cyano‐2H‐thiopyrans (C ₅— S insertion) were not isolated. Similar insertion was also observed in the reaction of 1 with methyl diazoacetoacetate and ethyl diazobenzoylacetate. The starting compounds 1 were synthesized by the reaction of tetrahydro‐4‐oxo‐3‐thiophene‐carbonitrile with morpholine, piperidine, and pyrrolidine in the presence of formic acid in ethanol.     

The nature of polymer grafts and substrate shape on the surface degradation of poly(l‐lactide)

Surface grafting of functional polymers is an effective method to alter material properties and degradation behavior. Two different substrate shapes of poly(l ‐lactide) (PLLA), i.e., films and microparticles, were surface‐grafted with hydrophilic monomers, and their surface degradation was monitored. Surface grafting with a hydrophilic and acidic polymer graft [acrylic acid (AA)] induced large alterations in the surface morphology and topography of the films. In contrast, hydrophilic and neutral polymer grafts [acrylamide (AAm)] had no significant effect on the surface degradation behavior, while the PLLA reference and co‐monomeric (AA/AAm) polymer‐grafted samples exhibited intermediate surface degradation rates. The grafted PAA chains induced a local acidic environment on the surface of the substrates, which in turn catalyzed the surface degradation process. This effect was more pronounced in the films than in the microparticles. Thus, the nature of the grafted chains and substrate geometry were shown to affect the surface degradation behavior of PLLA substrates. © 2015 The Authors Journal of Applied Polymer Science Published by Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42736.     

Synthesis and characterization of poly(amide–imide)s and their precursors as materials for membranes

Water soluble diamine amic acids (DAAs) were synthesized by reacting aliphatic diamines with pyromellitic dianhydride. Poly(amide–amic acid)s (PAAs) were prepared by interfacial polycondensation of DAAs in aqueous sodium hydroxide solution with isophthaloyl chloride in dichloromethane. Poly(amide–imide)s (PAIs) containing alternating (amide–amide)–(imide–imide) sequences were obtained by thermal cycloimidization of the PAA films at 175°C for 4 h in a forced air woven. The PAIs were readily soluble in polar aprotic solvents such as dimethylformamide, dimethylacetamide, dimethylsulfoxide, and N‐methyl‐2‐pyrrolidone. The inherent viscosities of the polymers are in the range of 0.97–1.7 dL/g. The polymers were characterized by IR, ¹H nuclear magnetic resonance (NMR), and thermogravimetric analysis (TGA). Thin film composite membranes containing PAA ultrathin barrier layer were prepared by in situ interfacial polycondensation of DAA in water with trimesoyl chloride or isophthaloyl chloride in hexane on the surface of a porous polysulfone membrane. The membranes were characterized for water permeability and for the separation of NaCl and Na₂SO₄. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 75: 1721–1727, 2000     

Production of nano‐calcium carbonate from shells of the freshwater channeled applesnail,Pomacea canaliculata,by hydrothermal treatment and its application with polyvinyl chloride

The use of naturally renewable shells of the freshwater channeled applesnail, Pomacea canaliculata, as a filler to replace commercial calcium carbonate (CaCO₃) was investigated in this study. Ground P. canaliculata shell particles were converted to nano‐CaCO₃ particles by the displacement reaction of calcium chloride in sodium carbonate solution followed by hydrothermal treatment at 100°C for 1 h to synthesize nano‐CaCO₃ with particle sizes of 30–100 nm in diameter. The mechanical properties, in terms of the tensile strength, elongation at brake and impact strength, of polyvinyl chloride (PVC) were greatly improved by mixing with nano‐CaCO₃ at 5–10 parts per hundred of resin. Additionally, the presence of nano‐CaCO₃ at the same levels increased the flame resistance and thermal stability of the PVC composite materials. POLYM. COMPOS., 36:1620–1628, 2015. © 2014 Society of Plastics Engineers     

Superabsorbent composite. XIII. Effects of Al3+‐attapulgite on hydrogel strength and swelling behaviors of poly(acrylic acid)/Al3+‐attapulgite superabsorbent composites

Al³⁺‐attapulgite (Al³⁺‐APT) was prepared by treating attapulgite (APT) with AlCl₃ aqueous solution of various concentrations. The poly(acrylic acid)/Al³⁺‐attapulgite (PAA/Al³⁺‐APT) superabsorbent composite was prepared by reaction of partly neutralized acrylic acid, and Al³⁺‐APT in aqueous solution using N, N′‐methylenebisacrylamide as a crosslinker and ammonium persulfate as an initiator. The surface morphology of the composite was investigated by SEM, and the Al³⁺‐APT composite generated a relatively planar surface comparing the nature APT. The effects of Al³⁺‐APT on hydrogel strength and swelling behaviors, such as equilibrium water absorbency, swelling rate, and reswelling capability, of the superabsorbent composites were also studied. The hydrogel strength and reswelling capability were improved, however, the equilibrium water absorbency and swelling rate decreased with increasing AlCl₃ solution concentration. The equilibrium water absorbency firstly increased, and then decreased with increasing Al³⁺‐APT content. The results indicate that Al³⁺‐APT acts as an assistant crosslinker in the polymeric network, which has great influences on hydrogel strength and swelling behaviors of the PAA/Al³⁺‐APT superabsorbent composites. POLYM. ENG. SCI., 47:619–624, 2007. © 2007 Society of Plastics Engineers.     

Multilayer composite surfaces prepared by an electrostatic self‐assembly technique with quaternary ammonium salt and poly(acrylic acid) on poly(acrylonitrile‐co‐acrylic acid) membranes

An electrostatic self‐assembly technique was applied to prepare ion complex polymer layers on polyacrylonitrile with acrylic acid segments {poly(acrylonitrile‐co‐acrylic acid) [P(AN‐co‐AA)]}. For the ionic complex layers, quaternary ammonium salts, such as cetyl trimethyl ammonium chloride (CTAC) and tetramethyl ammonium chloride (TMAC), were used as cationic species, and also, poly(acrylic acid) (PAA) was used as an anionic species. These cationic and anionic species were self‐assembled alternately on the surface of the P(AN‐co‐AA) membrane. Fourier transform infrared spectroscopy, AFM, and water contact angle measurements of the membrane surface were used to confirm the formation of the multilayer composites on the P(AN‐co‐AA). The permeabilities of water and macromolecules of different molecular weights were evaluated by a membrane filtration technique. The values of permeability strongly depended on the formation layer by layer of these ion composites on the base P(AN‐co‐AA). Through the measurement of the values of the contact angle of water, it was clear that surface nature of the base membrane treated by CTAC or TMAC and PAA dramatically changed. We concluded that such an electrostatic self‐assembly technique is useful for the preparation of multicomposite layers to modify the surface of base P(AN‐co‐AA) membranes. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Thermal properties of phosphorylated nanodiamond reinforced polyimides

Recently, the preparation of nanodiamond–polymer composites has attracted the attention of materials scientists due to the unique properties of nanodiamonds. In this study, novel polyimide (PI)/phosphorylated nanodiamonds (PNDs) composites were prepared. PNDs were achieved from the reaction of methylphosphonic dichloride with nanodiamonds in dichloromethane. Precursor of polyimide, which is the poly(amic acid) (PAA), was successfully synthesized with 3,3′, 4,4′‐benzophenonetetracarboxylic dianhydride and 4,4′‐oxydianiline in the solution of N,N‐dimethylformamide. Different ratios of phosphorylated nanodiamond particles were added into PAA solution and four different nanocomposite films were prepared. The amount of PNDs in the composite films was varied from 0 wt% to 3 wt%. The structure, thermal and surface properties of polyimide films were characterized by scanning electron microscopy (SEM), ATR‐FTIR, thermogravimetric analysis (TGA), ultraviolet visible spectroscopy, and contact angle. SEM and FTIR results showed that the phosphorylated nanodiamond and PI/PNDs films were successfully prepared. Phosphorylated nanodiamonds were homogeneously dispersed in the polymer matrix and they displayed good compatibility. TGA results showed that the thermo‐oxidative stability of PI/PNDs films was increased with the increasing amount of phosphorylated nanodiamond. POLYM. COMPOS., 37:2285–2292, 2016. © 2015 Society of Plastics Engineers