Preparation and properties of polyethylene terephthalate/polyethylene/near infrared reflective pigment composites

Polyethylene terephthalate/high density polyethylene (PET/HDPE) composites containing a near infrared reflective (NIR, nickel antimony titanium yellow rutile) pigment was prepared using ethylene‐glycidyl methacrylate‐vinyl acetate (EGMA‐VA) as a compatibilizer to increase the infrared reflection of PET/HDPE and limit the thermal heat accumulation in light of environmental and energy conservation concerns. HDPE was premixed with NIR to form N‐HDPE masterbatch. A good interfacial bonding between PET matrix and HDPE dispersed phase with the help of compatibilizer was confirmed through Fourier transform‐infrared spectra, scanning electron microscopy, and torque rheometer. For PET/N‐HDPE composites, the major X‐ray diffraction peaks and melting behaviors remained unchanged, indicating the limited alternation of crystalline structure for the composite systems with or without compatibilizer. The observed increment in the crystallization temperature of PET for the investigated PET/N‐HDPE composites was mainly due to the nucleation role of both inorganic NIR and HDPE. Tensile strength and elongation at break for compatibilized cases at various N‐HDPE contents conferred higher values than those of the corresponding counterparts without compatibilizer. Yet, Young's modulus for compatibilized systems was about 40% lower than that for systems without compatibilizer, attributed to the rubbery nature of EGMA‐VA. With the inclusion of NIR into HDPE to form PET/N‐HDPE composites with or without EGMA‐VA compatibilizer, the values of reflectance increased to a great degree. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40830.     

Accelerated weathering properties of compatibilized composites made from recycled HDPE and nonmetallic printed circuit board waste

The main aim of this work is to examine the influence of the contents of nonmetallic printed circuit board (PCB) waste component on the photodegradation of recycled high‐density polyethylene (rHDPE) composites. The properties tested were chemical changes, flexural properties, color stability, water absorption, leaching properties, and crystallinity changes of the composites after exposure to 2,000 h of accelerated weathering. Surface degradation for composites with nonmetallic PCB was less compared to unfilled rHDPE mainly because glass fibers covered almost the whole surface of specimens, acting as a protective layer, thus, slowing down the photodegradation reaction. Incorporation of compatibilizer in rHDPE/PCB composites had played an important role in resisting degradation due to UV exposure. All the composite samples became lighter in the early stages of weathering exposure; however, compatibilized composites showed less lightening and reduction on strength and modulus. Carbonyl index increases with exposure time indicating that the oxidation reaction continuously occurred during the aging process. Incorporation of compatibilizer had successfully reduced the water absorption uptake by the composites and effectively delayed some degradation properties of weathering. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43110.     

Thermal and mechanical properties of polypropylene/wood‐flour composites

In this research, polypropylene/wood‐flour composites (WPCs) were blended with different contents of wood and/or maleated polypropylene (MAPP) and clay. We found that the addition of MAPP or clay in the formulation greatly improved the dispersion of the wood fibers in the composite; this suggested that MAPP or clay may have played the role of an adhesion promoter in the WPCs. The results obtained with clay indicate that it also acted as a flame retardant. The thermal tests carried out with the produced samples showed an increased crystallization temperature (T_c), crystallinity, and melting temperature (T_m) with wood loading. The increase of the two former parameters was explained by the incorporation of wood flour, which played the role of nucleating agent and induced the crystallization of the matrix polymer. On the other hand, the T_m increase was ascribed to the insulating properties of wood, which hindered the movement of heat conduction. The effects of UV irradiation on T_m and T_c were also examined. T_c increased with UV exposure time; this implied that UV degradation generated short chains with low molecular weight that could move easily in the bulk of the sample and, thus, catalyze early crystallization. The flexural strength and modulus increased with increasing wood‐flour content. In contrast, the impact strength and tensile strength and strain decreased with increasing wood‐flour content. All of these changes were related to the level of dispersion of the wood flour in the polymeric matrix. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Thermal and mechanical characterization of linear low‐density polyethylene/wood flour composites

A linear low‐density polyethylene (LLDPE) matrix was modified with an organic peroxide and by a reaction with maleic anhydride (MAn) and was simultaneously compounded with untreated wood flour in a twin‐screw extruder. The thermal and mechanical properties of the modified LLDPE and the resulting composites were evaluated. The degree of crystallinity was reduced in the modified LLDPE, but it increased with the addition of wood flour for the formation of the composites. Significant improvements in the tensile strength, ductility, and creep resistance were obtained for the MAn‐modified composites. This enhancement in the mechanical behavior could be attributed to an improvement in the compatibility between the filler and the matrix. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2775–2784, 2003     

Toughening mechanism of PPS/Sr ferrite composites by TPU elastomer

In order to improve the impact strength of PPS‐based strontium ferrite composite, the thermoplastic polyurethane (TPU) elastomer was added in the composite as a toughening agent. The composites were obtained by melt‐blending PPS, TPU and strontium ferrites in twin‐screw extruder. The crystalline state, thermal property, surface morphology and impact strength of the composites were investigated by using X‐ray diffraction, differential scanning calorimetry, thermoravimetric analysis, scanning electron microscope and izod impact test. The addition of TPU improves impact strength of PPS‐based strontium ferrite composite. When the addition of TPU increases to 11wt %, the impact strength of Sr‐ferrite/PPS/TPU composite is enhanced by 51.44% compared with the sample without TPU addition, and reaches to 5.77 kJ/m². The occurrence of bonding interaction between PPS and TPU, demonstrated by a series of experiments, changes the structure and impact properties of PPS. Based on the experimental results, a possible mechanism is proposed to explain the improvement of Sr‐ferrite/PPS/TPU composites, which is different from the conventional toughening mechanism by the conformation of elastomers and the suppression of microcracks propagation. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43564.     

Mechanical,dielectric, and thermal properties of fluorosilicone rubber composites filled with silica/multiwall carbon nanotube hybrid fillers

In this work, hybrid fillers consist of modified silica (SiO₂) and multiwalled carbon nanotube (MWCNT) were used to improve the mechanical, dielectric, and thermal properties of fluorosilicone (FSR) composites via a direct mechanical mixing method. With the increase of CNT loading in SiO₂/CNT hybrid loading ratio, the tensile properties, dielectric constant, electrical conductivity, and thermal properties all increase without a sharp sacrifice of flexibility. The dielectric constant of FSR-S15/C5 achieved 7,370 @1 kHz, which is about four orders of the FSR-S20, and the dielectric loss remains as low as 0.676 @1 kHz. Therefore, the linkage of SiO₂ and FSR chains not only enhances the interfacial interaction between the fillers and FSR matrix but also decreases the agglomeration of the fillers in matrix. What is more, modified SiO₂ and CNT were designed as the effective hybrid filler to improve the performance of the polymeric matrix through synergic effect.     

Structure and properties of UHMWPE fiber/carbon fiber hybrid composites

Ultrahigh molecular weight polyethylene (UHMWPE) fiber/carbon fiber hybrid composites were prepared by inner‐laminar and interlaminar hybrid way. The mechanical properties, dynamic mechanical analysis (DMA), and morphologies of the composites were investigated and compared with each other. The results show that the hybrid way was the major factor to affect mechanical and thermal properties of hybrid composites. The resultant properties of inner‐laminar hybrid composite were better than that of interlaminar hybrid composite. The bending strength, compressive strength, and interlaminar shear strength of hybrid composites increased with an increase in carbon fiber content. The impact strength of inner‐laminar hybrid composite was the largest (423.3 kJ/m²) for the UHMWPE fiber content at 43 wt % to carbon fiber. The results show that the storage modulus (E′), dissipation factor (tan δ), and loss modulus (E″) of the inner‐laminar hybrid composite shift toward high temperature remarkably. The results also indicate that the high‐performance composite with high strength and heat resistance may be prepared by fibers' hybrid. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 1880–1884, 2006     

PVDF/PMMA/Basalt fiber composites: Morphology,melting and crystallization,structure, mechanical properties,and heat resistance

This paper is to study the effect of basalt fiber on morphology, melting and crystallization, structure, mechanical properties, melting and crystallization of PVDF/PMMA composites using scanning electron microscopy (SEM), X‐ray, differential scanning calorimeter (DSC), dynamical mechanical analysis (DMA), etc. Basalt fiber may disperse well in PVDF/PMMA matrix and form compact fiber network, and this makes tensile and flexural strength of fiber reinforced PVDF/PMMA composites get to the maximum value of 62 and 102 MPa, respectively. However, the mechanical properties begin to decrease when basalt fiber content exceeds 20 wt %. The α and β phase of PVDF can coexist in composites, and basalt fiber and PMMA can induce β phase of PVDF. The melting temperature of PVDF in composites is kept unchanged, but the degree of crystallinity of composites increases as basalt fiber content increase, and then declines when fiber content exceeds 20%. The DSC results confirm that the nucleation ability of PVDF is enhanced by basalt fiber. Also, the heat resistance of PVDF/PMMA composite is improved from 133 to 146.1°C due to basalt fiber. The DMA shows that basalt fiber increases the storage modulus of PVDF/PMMA composite, and the loss peak of PMMA increases from 116.1 to 130°C. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40494.     

Mechanical and thermal properties of polyphenylene sulfide/multiwalled carbon nanotube composites

Polyphenylene sulfide (PPS)/multiwalled carbon nanotube (MWCNT) composites were prepared using a melt‐blending procedure combining twin‐screw extrusion with centrifugal premixing. A homogeneous dispersion of MWCNTs throughout the matrix was revealed by scanning electron microscopy for the nanocomposites with MWCNT contents ranging from 0.5 to 8.0 wt %. The mechanical properties of PPS were markedly enhanced by the incorporation of MWCNTs. Halpin‐Tsai equations, modified with an efficiency factor, were used to model the elastic properties of the nanocomposites. The calculated modulus showed good agreement with the experimental data. The presence of the MWCNTs exhibited both promotion and retardation effects on the crystallization of PPS. The competition between these two effects results in an unusual change of the degree of crystallinity with increasing MWCNT content. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

PPS/CaCO3复合材料的结晶行为及动态力学研究

采用DSC、DMA等测试手段研究了PPS/CaCO_3复合材料的结晶行为和动态力学性能。通过对冷结晶峰值温度T_(?)、半结晶时间t_(1/2)、结晶焓△H_c等参数的分析,结果表明:CaCO_3的添加阻碍了PPS分子链的运动,导致了体系结晶速率减小,结晶能力下降,且阻碍作用在CaCO_3含量为3%时最为明显。同时,通过DMA测试,表明CaCO_3的添加使PPS的储能模量和损耗模量都有所增加,其中损耗模量也在CaCO_3含量为3%时达到最大。     

Morphology,thermal expansion,and electrical conductivity of multiwalled carbon nanotube/epoxy composites

Multiwalled carbon nanotube/epoxy composites loaded with up to 0.5 wt % multiwalled carbon nanotubes were prepared and characterized. Infrared microscopy, scanning electron microscopy, thermogravimetry, differential scanning calorimetry, thermomechanical analysis, and electrical conductivity measurements of the composites were performed. Infrared microscopy and scanning electron microscopy images showed that the debundled nanotubes were well dispersed. The thermal expansion coefficients, before and after the glass transition, remained approximately constant with the addition of nanotubes, whereas the electrical conductivity at room temperature increased approximately 5 orders of magnitude. This result was attributed to the thermal expansion coefficients of the intertube gap on the carbon nanotube bundles, which were in the same range as that of the epoxy resin. Therefore, nanocomposites capable of electrostatic dissipation can be processed as neat epoxy materials with respect to the volume changes with temperature. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Crystallization and thermal properties of polylactide/palygorskite composites

Polylactide palygorskite (fibrous clay) composites were prepared by solvent casting method. Both pristine and organically modified palygorskite were used for composite preparation. The detailed crystallization behavior, morphology, and thermal properties of neat polylactide and the corresponding composites were investigated by using differential scanning calorimetry, polarized optical microscopy, scanning electron microscopy and wide angle X‐ray diffraction techniques. The results showed that the crystallization and thermal characteristics of neat PLA were influenced significantly by the presence of palygorskite nanoparticles. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40414.     

Modeling and statistical understanding: The effect of carbon nanotube on mechanical properties of recycled polycaprolactone/epoxy composites

Recycling of polymer composites has been explored in an attempt to reutilize materials. Several efforts have opted to address this subject from many perspectives including mechanical, chemical, and thermal recycling. Others have also delved into the self-healing materials to remedy this dilemma. However, few studies have delved into understanding the role of carbon nanotube (CNT) in self-healing based recycled polymer composites. Therefore, in this study, experimental and simulation tools were utilized to understand the recycling process when CNTs were incorporated within recycled polycaprolactone/epoxy composites. A polynomial regression model, as a facile approach, was established to simulate the process-property relationship, which is essential for the successful implementation of the future of manufacturing. It found that, by adding CNTs, a reduction in the determined degree of crystallization was induced which correlated with the obtained reduction in the modulus and toughness. Strategies for enhancing mechanical properties have been pointed out for future endeavors.     

Mechanical and thermal properties of polypropylene/modified basalt fabric composites

Basalt fabric (BF) was first treated with silane coupling agent KH550, modified basalt fabric (MBF) was obtained. Then MBF were molded with polypropylene (PP) matrix, and polypropylene/modified basalt fabrics (PP/MBF) composites were obtained. The influence of concentration and treating time of KH550 on MBF were characterized by hydrophilicity and lipophilicity. The tensile strength and morphology of basalt fabric were tested by single filament strength tester and scanning electron microscopy. The mechanical properties of composites were measured with electronic universal testing machine and impact testing machine, and the thermal properties were tested by thermogravimetric analysis and dynamic mechanical analysis. The results showed that the lipophilicity of MBF is improved significantly by KH550 while the tensile is nearly damaged. The mechanical properties of composites are larger than that of pure PP, among which the impact property was improved the most, showing 194.12% enhancement. The thermal stability and dynamic viscoelasticity were better than pure PP; furthermore, the concentration of KH550 virtually had no effect on the thermal stability. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42504.     

Thermoplastic polyvinyl alcohol/multiwalled carbon nanotube composites: Preparation,mechanical properties,thermal properties,and electromagnetic shielding effectiveness

This study uses the solution mixing method to combine plasticized polyvinyl alcohol (PVA) as a matrix, and multiwalled carbon nanotubes (MWCNTs) as reinforcement to form PVA/MWCNTs films. The films are then laminated and hot pressed to create PVA/MWCNTs composites. The control group of PVA/MWCNTs composites is made by incorporating the melt compounding method. Diverse properties of PVA/MWCNTs composites are then evaluated. For the experimental group, the incorporation of MWCNTs improves the glass transition temperature (T_g), crystallization temperature, T_c), and thermal stability of the composites. In addition, the test results indicate that composites containing 1.5 wt % of MWCNTs have the maximum tensile strength of 51.1 MPa, whereas composites containing 2 wt % MWCNTs have the optimal electrical conductivity of 2.4 S/cm, and electromagnetic shielding effectiveness (EMI SE) of ?31.41 dB. This study proves that the solution mixing method outperforms the melt compounding method in terms of mechanical properties, dispersion, melting and crystallization behaviors, thermal stability, and EMI SE. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43474.     

Preparation and properties of multiwalled carbon nanotube/epoxy‐amine composites

Different amounts of multiwalled carbon tubes (MWCNTs) were incorporated into an epoxy resin based on diglycidyl ether of bisphenol A and both epoxy precursor and composite were cured with 4,4′‐diamino diphenyl sulfone. Transmission and scanning electron microscopy demonstrated that the carbon nanotubes are dispersed well in the epoxy matrix. Differential scanning calorimetry measurements confirmed the decrease in overall cure by the addition of MWCNTs. A decrease in volume shrinkage of the epoxy matrix caused by the addition of MWCNTs was observed by pressure–volume–temperature measurements. Thermomechanical and dynamic mechanical analysis were performed for the MWCNT/epoxy composites, showing that the T_g was slightly affected, whereas the dimensional stability and stiffness are improved by the addition of MWCNTs. Electrical conductivity measurements of the composite samples showed that an insulator to conductor transition takes place between 0.019 and 0.037 wt % MWCNTs. The addition of MWCNTs induces an increase in both impact strength (18%) and fracture toughness (38%) of the epoxy matrix with very low filler content. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Thermosetting polyurethane‐multiwalled carbon nanotube composites: Thermomechanical properties and nanoindentation

In this study, composites based on a thermoset polyurethane elastomer (PU) and multiwalled carbon nanotubes (MWCNT) in the case of a PU of high elastic modulus (>200 MPa) are analyzed for the first time. As‐grown and modified nanotubes with 4 wt % of oxygenated functions (MWCNT‐ox) were employed to compare their effect on composite properties and maxima mechanical properties (elastic modulus and tensile strength) were reached at 0.5 wt % of MWCNT‐ox. Furthermore, by examining the morphology using optical and electron microscopies better dispersion and interaction of the nanotube‐matrix was observed for this material. DMTA data supports the observation of an increase in the glass transition temperature of ～20°C in the nanocomposites compared with the thermoset PU, which is an important result because it shows extended reliability in extreme environments. Finally, nanoindentation tests allowed a comparison with the conventional mechanical tests by measuring the elastic modulus and hardness at the subsurface of PU and the nanocomposites. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 41207.     

Mechanical and thermal transmission properties of carbon nanofiber‐dispersed carbon/phenolic multiscale composites

The present article reports the development and characterization of carbon nanofiber (CNF)‐incorporated carbon/phenolic multiscale composites. Vapor‐grown CNFs were dispersed homogeneously in to phenolic resin using an effective dispersion route, and carbon fabrics were subsequently impregnated with the CNF‐dispersed resin to develop carbon fiber/CNF/phenolic resin multiscale composites. Mechanical and thermal transmission properties of multiscale composites were characterized. Elastic modulus and thermal conductivity of neat carbon/phenolic and multiscale composites were predicted and compared with the experimental results. It was observed that incorporation of only 1.5 wt % CNF resulted in 10% improvement in Young's modulus, 12% increase in tensile strength, and 36% increase in thermal conductivity of carbon/phenolic composites. Fracture surface of composite samples revealed the formation of stronger fiber/matrix interface in case of multiscale composites than neat carbon/phenolic composites. Enhancement of above properties through CNF addition has been explained, and the difference between the predicted values and experimental results has been discussed. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Surface organo-modification of hydroxyapatites to improve PLA/HA compatibility

Polylactide/hydroxyapatite (PLA/HA) composites are promising tissue engineering materials because of the PLA biodegradability and HA as a natural bone component. PLA/HA composites without HA modification lead to mechanical failure due to the interfacial immiscibility. In this study, an effective chemical surface methodology is used to modify HA to obtain PLA/HA composites with superior mechanical properties. The HA particles are modified with fatty acids (adipic, sebacic, lauric, and linoleic) and incorporated into a PLA matrix by polymer solution casting, using chloroform as the solvent. After the HA modification, the films exhibited an improvement in tensile strength, elongation at break, and elastic modulus. Yet, the best results observed are by sebacic and adipic acid modification. These increments are attributed to a higher affinity of the organo-modified HA particles within the PLA matrix. Therefore, the development of materials for osteo-regeneration engineering based on these systems is quite promising.     

Recycling carbon fiber composites using microwave irradiation: Reinforcement study of the recycled fiber in new composites

With increasing use of carbon fiber reinforced polymer (CFRP) composites in transportation, sports, and many other industries, recycling of the scrap and end‐of‐life composites has presented both great challenges and opportunities. In this work, we report our study on reclaiming carbon fibers from CFRP using energy efficient microwave irradiation. Different irradiation conditions were used and the optimal conditions were determined based on the surface morphology of the recycled fiber. Polypropylene (PP) and Nylon, representing nonpolar and polar polymers, respectively, were reinforced using the recycled fiber through extrusion and injection molding. For comparison, PP and Nylon reinforced by virgin carbon fiber were also prepared using the same processing conditions. Tensile, flexural, and impact test results showed that, while both carbon fibers could improve these properties, they exhibited different reinforcing effects on the two polymers. The recycled fiber outperformed the virgin fiber in reinforcing PP whereas the virgin fiber performed better in Nylon. This was due to the differences in surface roughness, surface bonding, and fiber aspect ratio between the two fibers. This study shows the great potential of recycled carbon fiber and microwave irradiation as an effective recycling technique. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42658.