Preparation of polystyrene/MMT nanocomposite through in situ RAFT polymerization by new chain transfer agent derived from bisphenol A

Reversible addition‐fragmentation chain transfer (RAFT) polymerization was performed in the presence of a new RAFT agent based on bisphenol A and modified clays and successfully prepared polystyrene/MMT nanocomposite. The structure of RAFT agent was investigated by Fourier transform infrared spectroscopy (FT‐IR) and proton nuclear magnetic resonance spectroscopy (¹H NMR). The polymer had well‐defined molecular weight and narrow polydispersity obtained by gel permeation chromatography (GPC). The morphology of polystyrene/MMT nanocomposite was investigated by X‐ray diffraction (XRD) and transmission electron microscopy (TEM) and was found to be exfoliated. Thermal stability of pure polystyrene and polystyrene/MMT synthesized via RAFT polymerization was also investigated and showed better thermal stability for nanocomposite. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Characterization of Magnesium‐Doped Hydroxyapatite Prepared by Sol‐Gel Process

Pure and doped hydroxyapatite (HA) nanocrystalline powders (Ca_10‐xMg_x(PO₄)₆OH₂) were synthesized using sol‐gel process. For this, calcium nitrate tetrahydrate, magnesium nitrate hexahydrate, and phosphorous pentoxide were used as precursors for Ca, Mg, and P, respectively. Calculated amounts of magnesium ions (Mg⁺²) especially from 0 to 10% (molar ratio) were incorporated as dopant into the calcium sol solution. The structure and morphology of the gels obtained after mixing the phosphorous and (calcium + magnesium) sol solution were different, and their condensations in time depend on the quantities of magnesium added. The several powders resulting from the gels dried and sintered at 500°C for 1 h were characterized by thermogravimetry (TG), Fourier transform infrared spectroscopy (FTIR), X‐ray diffraction (XRD), and inductively coupled plasma (ICP). Additionally, their agglomeration, morphology, and particle size were investigated using scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The specific surface area of each sample was measured by the Brunauer–Emmett–Teller (BET) gas adsorption technique. The results of XRD, FTIR, and ICP values ranged between 0.45 and 2.11 mg/L indicated that the magnesium added in the calcium solution was incorporated in the lattice structure of HA so prepared, while those obtained by SEM and TEM confirmed the influence of Mg on their morphology (needle and irregular shape) and crystallite size, which is about 30–60 nm. The as‐prepared powders had a specific surface area ranged between 6.37 and 27.60 m²/g.     

Effect of montmorillonite on the swelling behavior and drug‐release behavior of nanocomposite hydrogels

A series of nanocomposite hydrogels were prepared from various ratios of N‐isopropylacrylamide (NIPAAm) and organic montmorillonite (MMT). The influence of the extent of MMT in the NIPAAm/MMT nanocomposite hydrogels on the physical properties and drug‐release behavior was the main purpose of this study. The microstructure and morphology were identified by X‐ray diffraction (XRD) and scanning electronic microscopy (SEM). The results showed that the swelling ratios for these nanocomposite hydrogels decreased with increase in the content of MMT. The gel strength and Young's modulus of the gels also increased with increase in the content of MMT. XRD results indicated that the exfoliation of MMT was achieved in the swollen state. Finally, the drug‐release behavior for the gels was also assessed. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 3652–3660, 2003     

Preparation and characterization of elastomer‐based nanocomposite gels using an unique latex blending technique

Nanocomposite (NC) gels based on natural rubber (NR) and styrene butadiene rubber (SBR) were prepared by using a unique latex blending technique. These NC gels were prepared by first blending the water swollen unmodified montmorillonite clay (Na⁺‐MMT) suspension into the respective latices followed by prevulcanization to generate crosslinked nanogels. Use of water assisted fully delaminated Na⁺‐MMT suspension resulted in predominantly exfoliated morphology in the NC gels, as revealed by X‐ray diffraction study and transmission electron microscopy. Addition of Na⁺‐MMT significantly improved various physical, mechanical and thermal properties of these NC gels. For example, 6 phr of Na⁺‐MMT loaded NR based NC gels registered 54% and 200% increase in tensile strength and Young's modulus, respectively, compared to the unfilled NR gels. SBR based NC gels also showed similar level of improvement in mechanical properties. Mechanical properties of NC gels prepared using this route were also compared with the NC gels prepared by co‐coagulation and conventional curing technique and found to be superior. In the case of dynamic mechanical properties, NC gels showed higher glass transition temperatures along with a concomitant increase in storage moduli, compared to the unfilled gels. These Na⁺‐MMT reinforced NC gels also exhibited markedly improved thermal stability. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Preparation and characterization of nanocomposite hydrogels based on polyacrylamide for enhanced oil recovery applications

In the present work, attempts have been made to prepare nanocomposite type of hydrogels (NC gels) by crosslinking the polyacrylamide/montmorillonite (Na‐MMT) clay aqueous solutions with chromium (III). The X‐ray diffraction patterns of the NC gels exhibited a significant increase in d₀₀₁ spacing between the clay layers, indicating the formation of intercalated as well as exfoliated type of morphology. Exfoliation of the clay layers through out the gel network was found to be predominated, which evidences the high interaction between the polyacrylamide segments and montmorillonite layers. Gelation time as well as variation of viscoelastic parameters such as storage modulus (G′) of the gel network during gelation process at 75°C was studied and followed by rheomechanical spectroscopy (RMS). The NC gels prepared with lower crosslinker concentration showed higher strength and elastic modulus compared with the similar but unfilled polyacrylamide gel. This distinct characteristic of the NC gels yields a gel network structure with high resistance towards syneresis at high temperature in the presence of the oil reservoir formation water. The effects of the composition, such as clay content, crosslinker concentration, and also water salinity upon the gelation rate, gel strength as well as rate of syneresis have been investigated. To optimize the injectivity of the intercalated polyacrylamide solution before the onset of gelation with the gel strength of the final developed gel, sodium lactate was employed as retarder. This was found to be effective to balance these two characteristics of the NC gels, which are aimed to be used for water shut‐off and as profile modifier in enhanced oil recovery (EOR) process during water flooding process. The nanocomposite gels showed much more elasticity and extensibility at low crosslinker concentration compared with the similar but unfilled gel, which makes the NC gels suitable as an in‐depth profile modifier, and also as an oil displacing agent in the heterogeneous oil reservoir in chemical EOR. Effects of the clay content on the thermal stability of the gel network have also been investigated by thermogravimetric analysis (TGA). Scanning electron microscopy (SEM) has been performed upon the NC‐gel samples. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 2096–2103, 2006     

Preparation and properties of PET/PA6 copolymer/montmorillonite hybrid nanocomposite

From in situ polycondensation, a poly(ethylene terephthalate)/Polyamide 6 copolymer/montmorillonite nanocomposite was prepared, after the treatment of montmorillonite (MMT) with a water soluble polymer. The resulting nanocomposites were characterized by X‐ray diffraction (XRD), differential scanning calorimeter (DSC), nuclear magnetic resonance (NMR), dynamic mechanical analysis (DMA), and transmission electron microscopy (TEM). The results of DSC, ¹H NMR, and DMA proved that the nanocomposite synthesized was PET/PA6 copolymer/MMT nanocomposite, not the PET/PA6 blend/MMT nanocomposite. The results of XRD and TEM proved that the dispersion of MMT was improved observably after the introduction of PA6 molecular chain into PET. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 2512–2517, 2006     

Novel preparation and properties of EPDM/montmorillonite nanocomposites

This article reports on a novel route to develop ethylene–propylene–diene rubber (EPDM)/montmorillonite nanocomposites Modification of the MMT was carried out with maleic anhydride (MA), which acts as the intercalation agent for MMT and the vulcanizing agent for EPDM matrix, as well as the compatibilizer for the EPDM and MMT phases. The effect of MA‐modified MMT in nanocomposites was investigated by focusing on three major aspects: structural analysis, thermal properties, and material properties. The d‐spacings of both the MA modified MMT and exfoliated nanocomposites were investigated by X‐ray diffraction (XRD), and the morphology of these nanocomposites was examined by transmission electron microscopy (TEM) and scanning electron microscopy (SEM). Dynamic mechanical analysis confirms the constraint effect of exfoliated MMT layers on EPDM chains, which benefited the increased storage modulus, increased glass transition temperature. Thermogravimetric analysis indicates that there is some enhancement in degradation behavior between the nanocomposites and EPDM matrix. The nanocomposites exhibit great improvement in tensile strength and modulus, as well as elongation‐at‐break. The effects of MA addition on the formation of nano‐metric reinforcement and on the mechanical properties of nanocomposites are discussed. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 2578–2585, 2006     

Chitosan/clay nanocomposite film preparation and characterization

Nanocomposites of chitosan and nanoclays (MMT‐Na⁺ and Cloisite 30B) were prepared by solvent casting. The structural properties, thermal behaviors, and mechanical properties were characterized using X‐ray diffraction (XRD), transmission electron microscopy (TEM), atomic force microscopy, differential scanning calorimetry, thermogravimetry analyses, and an Instron universal testing machine. XRD and TEM results indicated that an exfoliated structure was formed with addition of small amounts of MMT‐Na⁺ to the chitosan matrix. Intercalation along with some exfoliation occurred with up to 5 wt % MMT‐Na⁺. Micro‐scale composite (tactoids) formed when Cloisite 30B was added to the chitosan matrix. Surface roughness increased with addition of a small amount of clay. Tensile strength of a chitosan film was enhanced and elongation‐at‐break decreased with addition of clay into the chitosan matrix. Melt behavior and thermal stability did not change significantly with addition of clays. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 1684–1691, 2006     

Synthesis and properties of poly(methyl methacrylate)/clay nanocomposites using natural montmorillonite and synthetic Fe‐montmorillonite by emulsion polymerization

In this article, Fe‐montmorillonite (Fe‐MMT) was synthesized by hydrothermal method. For the first time, Fe‐MMT was modified by cetyltrimethyl ammonium bromide (CTAB), and poly(methyl methacrylate)(PMMA)/Fe‐MMT nanocomposites were synthesized by emulsion polymerization. Then poly(methyl methacrylate)(PMMA)/natural montmorillonite (Na‐MMT) and PMMA/Fe‐MMT nanocomposites were compared by Fourier transform infrared (FTIR) spectra, X‐ray diffraction (XRD) patterns, transmission electron microscopy (TEM), and thermal gravimetric analysis (TGA). By XRD and TEM, it was found out that the morphology of PMMA/Fe‐MMT nanocomposites was different from that of the PMMA/Fe‐MMT nanocomposites when the content of two types of clay was same in the PMMA matrix. It was possible that the presence of iron may lead to some radical trapping, which enhances intragallery polymerization to be developed to improve layer dispersion in PMMA/Fe‐MMT systems. In TGA curves, the thermal stability and residue at 600°C of PMMA/Fe‐MMT nanocomposites were higher than those of PMMA/Na‐MMT nanocomposites. Those dissimilarities were probably caused by structural Fe ion in the lattice of Fe‐MMT. POLYM. COMPOS., 27:49–54, 2006. © 2005 Society of Plastics Engineers     

Synthesis and characterization of montmorillonite/polypyrrole nanocomposite

A novel montmorillonite (MMT)/polypyrrole (PPy) nanocomposite (MPN) with high electrical conductivity and thermal stability has been synthesized via in‐situ polymerization. The surface morphology, characterization, thermal stability, and electrical conductivity have been tested by scanning electron microscopy (SEM), Fourier‐transform infrared spectroscopy (FTIR), X‐ray diffraction (XRD), thermogravimetric analysis (TGA), and four‐probe methods, respectively. SEM results show that the antenna‐like PPy deposits on the layer surface of MMT. FTIR and XRD analyses show that there is interaction between MMT and PPy. The nanocomposite has high electrical conductivity (4 S/cm), eight orders of magnitude higher than that of pristine MMT. The thermal stability of MPN is higher than the pure PPy as well as the mixture of MMT and PPy (MMP). POLYM. COMPOS., 2009. © 2008 Society of Plastics Engineers     

Electron beam synthesis and characterization of poly(vinyl alcohol)/montmorillonite nanocomposites

Poly(vinyl alcohol) (PVA)/montmorillonite clay (MMT) nanocomposites in the form of films were prepared under the effect of electron beam irradiation. The PVA/MMT nanocomposites gels were characterized by X‐ray diffraction (XRD), differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), scanning electron microscopy (SEM), and mechanical measurements. The study showed that the appropriate dose of electron beam irradiation to achieve homogeneous nanocomposites films and highest gel formation was 20 kGy. The introduction of MMT (up to 4 wt %) results in improvement in tensile strength, elongation at break, and thermal stability of the PVA matrix. In addition, the intercalation of PVA with the MMT clay leads to an impressive improved water resistance, indicating that the clay is well dispersed within the polymer matrix. Meanwhile, it was proved that the intercalation has no effect on the metal uptake capability of PVA as determined by a method based on the color measurements. XRD patterns and SEM micrographs suggest the coexistence of exfoliated intercalated MMT layers over the studied MMT contents. The DSC thermograms showed clearly that the intercalation of PVA polymer with these levels of MMT has no influence on the melting transitions; however, the glass transition temperature (T_g) for PVA was completely disappeared, even at low levels of MMT clay. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 1129–1138, 2006     

Melt processing and characterization of polypropylene/pristine montmorillonite nanocomposite: Influence of compatibilizer and hyperbranched polymer

In the present investigation, nanocomposites of polypropylene (PP)‐montmorillonite (MMT) clay were prepared by a single‐step compounding method to study the influence of hyperbranched polyester (HBPE) on rheological and mechanical properties of PP composites in the presence of a compatibilizer. In service of this objective, polyvinylchloride‐grafted‐maleic anhydride (PP‐g‐MA) was used as a compatibilizer for hydrophobic PP and hydrophilic clay. Rheological property in terms of melt viscosity was examined by a Brabender torque rheometer. The composite's morphology was studied by scanning electron microscopy (SEM) and transmission electron microscopy (TEM), whereas the dispersion state of nanoparticles in the PP matrix was studied by X‐ray diffraction (XRD). The thermal behavior of nanocomposites was examined by differential scanning calorimetry (DSC). The analysis of results confirmed that the interactions among both additives significantly influenced the morphology, rheology, and thermomechanical properties of the nanocomposites. J. VINYL ADDIT. TECHNOL., 22:72–79, 2016. © 2014 Society of Plastics Engineers     

The effects of soft‐segment molecular weight and organic modifier on properties of organic‐modified MMT‐PU nanocomposites

The effects of soft‐segment molecular weight and organic modification of montmorillonite (MMT) on thermal and mechanical properties of segmented polyurethane (PU) elastomers were investigated. The PU/MMT nanocomposites were prepared by in situ polymerization, and the compositions included soft segments with number average molecular weights of 1000, 2000, and 2900, and organic‐modified MMT (including MMT‐30B and MMT‐I30E). The nanocomposites produced were characterized using wide‐angle X‐ray diffraction (WAXD), transmission electron microscopy (TEM), Fourier transform infrared spectroscopy (FTIR), differential scanning calorimetry (DSC), and mechanical testing. The TEM and XRD results revealed that both MMT‐30B and MMT‐I30E were intercalated, and partially exfoliated by the PU. Mechanical tests showed that the PU1000 series in soft‐segment molecular weight yielded superior tensile properties compared with the PU2000 and PU2900 series. Also, for a given molecular weight of soft segment in PU, the MMT‐30B nanocomposites exhibited greater increases in Young's modulus, tensile strength, and elongation at break than the MMT‐I30E counterpart, and the crystallinity of PU was enhanced by the clays. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Modification of structural,thermal, and electrical properties of PVA by addition of silicon carbide nanocrystals

SiC‐PVA nanocomposite films, synthesized using solution‐casting technique were structurally characterized using X‐ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR) and Raman spectroscopy. Morphological studies of the SiC‐PVA nanocomposite films were carried out using Transmission electron microscopy (TEM) and Scanning electron microscopy (SEM). TEM analysis confirms that the size of SiC nanocrystals present in PVA matrix are 23 ± 9 nm, which is consistent with size calculated using XRD. SiC‐PVA nanocomposite films were further characterized for their thermal and electrical properties. Thermogravimetric/differential thermal analysis (TG/DTA) indicates that the char yield of nanocomposite films containing 3 wt % SiC nanocrystal is ～30% more than PVA. This increase in char yield is an indication of the potency of flame retardation of SiC‐PVA nanocomposite films. I‐V analysis reveals that Schottky mechanism is the dominant conduction mechanism which is responsible for the increase in conductivity of PVA with the addition of SiC nanocrystals. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42464.     

Effects of Nickel Oxide (NiO) nanoparticles on the performance characteristics of the jatropha oil based alkyd and epoxy blends

Plant oil based alkyd resin was prepared from jatropha oil and blended with epoxy resin. Subsequently, alkyd/epoxy/NiO nanocomposites with different wt % of NiO nanoparticles have been prepared by mechanical mixing of the designed components. The structure, morphology, and performance characteristics of the nanocomposites were studied by UV‐visible spectroscopy, Fourier transform infrared (FTIR) spectroscopy, scanning electron microscopy (SEM), transmission electron microscopy (TEM), X‐ray diffraction (XRD), thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), and universal testing machine (UTM). The alkyd/epoxy/NiO nanocomposites showed the gradual increase in thermal stability with increasing NiO content. With 3 wt % NiO content the tensile strength of the nanocomposite increased by 19 MPa (more than twofold) when compared with the pristine polymer. Limiting oxygen index (LOI) value of the nanocomposites indicate that the incorporation of NiO nanoparticles even in 1 wt % can greatly improves the flame retardant property of the nanocomposites. This study confirms the strong influence of NiO nanoparticles on the thermal, mechanical, and flame retardant properties of the alkyd/epoxy/NiO nanocomposites. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41490.     

Rheology and curing characteristics of epoxy–clay nanocomposites

Diglycidyl ethers of bisphenol‐A (DGEBA) epoxy resin, filled separately with organoclay (OC) and unmodified clay (UC), were synthesized at room temperature and at high temperature (80 °C) by mechanical shear mixing. The room temperature curing (RTC) and high temperature curing (HTC) were carried out with the addition of triethylene tetramine (TETA) and diaminodiphenylmethane (DDM) curing agents respectively. The OC used was alkyl ammonium modified montmorillonite (MMT) and the UC was Na⁺‐MMT. X‐ray diffraction (XRD) and transmission electron microscopy (TEM) were used to study the structure and morphology of the nanocomposites. The influence of OC and UC particles on rheology and curing characteristics was studied. The rate of increase in viscosity was higher for OC‐filled resin than that of the UC‐filled resin. The curing study showed that the amine ions of the OC aided the polymerization process and favoured the curing at low temperature over the curing of unfilled epoxy resin. The tensile properties were enhanced for epoxy filled with OC particles rather than those filled with UC particles. Copyright © 2005 Society of Chemical Industry     

Microwave-assisted preparation of poly(2-EHA-co-ST) copolymer and poly(2-EHA-co-ST)/MMT nanocomposite

Copolymerization of 2-ethylhexylacrylate and styrene was performed in presence of benzoyl peroxide as initiator at varying concentrations of the comonomers in a microwave oven. Montmorillonite (MMT) clay was added with a view to prepare nanocomposites, which actually enhanced the water absorption capacity and pressure sensitive adhesive properties. The copolymer and its nanocomposite were characterized by Fourier Transform Infrared, ¹H- and ¹³C-NMR, thermogravimetric-differential thermal analysis (TG-DTA), differential scanning calorimeter, scanning electron microscopy, X-ray diffraction (XRD), and transmission electron microscopy (TEM). The MMT layers were partially exfoliated/intercalated during the polymerization process as evident from the XRD and TEM observations. Their adhesive properties, water absorbancy, and biodegradability in different conditions were studied for their future applications. The monomer reactivity ratios were determined using Finemann–Ross and Kelen–Tüdos method. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Synthesis and characterization of polyvinyl acetate/montmorillonite nanocomposite by in situ emulsion polymerization technique

Exfoliated polyvinyl acetate/montmorillonite nanocomposite (PVAc/MMT) was prepared via in situ emulsion polymerization. The resulting PVAc with various organophilic MMT contents was investigated. In the nanocomposite latex preparation, sodium lauryl sulfate (SLS), ammonium persulfate (APS), and poly (vinyl alcohol) (PVA) are used as anionic emulsifier, conventional anionic initiator, and stabilizer, respectively. The samples were characterized using elemental analysis, X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), atomic force microscopy (AFM). The XRD and AFM results demonstrate that the MMT well dispersed at molecular level in the PVAc matrix. Thermal properties of the nanocomposite were studied by using differential scanning calorimetric analysis (DSC). The exfoliated PVAc/MMT nanocomposite showed a higher glass transition temperature and a better thermal stability compared to the pure PVAc.     

Preparation and wear assessment of ultrasonic electrodeposited Ni–TiN thin films

In this study, pure Ni and Ni–TiN thin films were prefabricated from a reformative Watt nickel bath through ultrasonic electrodeposition (UE) under pulse current (PC) condition. The effects of ultrasonic intensity on surface morphology, microstructure and phase composition were evaluated through scanning electron microscopy (SEM), scanning probe microscopy (SPM), transmission electron microscopy (TEM) and X-ray diffraction (XRD). The Vickers hardness, the friction coefficient and the wear resistance of Ni and Ni–TiN thin films were also estimated. All SEM, SPM, and TEM results demonstrated that the Ni-TiN thin film obtained at the ultrasonic intensity of 30?W/cm² had a fine, smooth and homogeneous surface morphology. The root-mean-square roughness (Rms) and arithmetic mean roughness (Ra) of the film with a surface area of 4.096?µm² were 36.813?nm and 22.836?nm, respectively. Also, the mean diameters of Ni grains and TiN nanoparticles were approximately 46.7?nm and 23.2?nm, respectively. The XRD analysis indicated that the XRD patterns of the films prepared with different plating parameters had the same diffraction angle with the Ni phase except the diffraction intensity. Microhardness tests exhibited that the Ni film displayed the minimum microhardness value of 38.6 HV. Moreover, the Ni-TiN film obtained at the ultrasonic intensity of 30?W/cm² acquired the maximum microhardness value of 912.1 HV. The wear behavior assessment demonstrated that the Ni-TiN film prefabricated at the ultrasonic intensity of 30?W/cm² sustained the least weight loss, while the mean friction coefficient was approximately 0.39, thereby displaying the best wear resistance.     

Harmless hydrogels based on PVA/Na+‐MMT nanocomposites for biomedical applications: Fabrication and characterization

A series of nanocomposite hydrogels were prepared by a freeze‐thaw process, using polyvinyl alcohol (PVA) as polymer matrix and 0–10 wt% of hydrophilic natural Na‐montmorillonite (Na⁺‐MMT), free from any modification, as composite aggregates. The effect of nanoclay content and the sonication process on the nanocomposite microstructure and morphology as well as its properties (physical, mechanical, and thermal) were investigated. The microstructure and morphology were investigated by Fourier transform infrared spectroscopy, field emission scanning electron microscopy, transmission electron microscopy, atomic force microscopy, and X‐ray diffraction technique. The thermal stability and mechanical properties of nanocomposite hydrogels were examined using thermogravimetric analysis, differential scanning calorimetry, dynamic mechanical analysis; moreover hardness and water vapor transmission rate measurements. It was concluded that the microstructure, morphology, physical (thermal) and mechanical properties of nanocomposite hydrogels have been modified followed by addition of nanoclay aggregates. The results showed that Na⁺‐MMT may act as a co‐crosslinker. Based on the results obtained, the nanocomposite hydrogel PVA/Na⁺‐MMT synthesized by a freeze‐thaw process, appeared to be a good candidate for biomedical applications. POLYM. COMPOS., 38:1135–1143, 2017. © 2015 Society of Plastics Engineers