Mechanical and thermal properties of epoxy-POSS reinforced-(biphenyl diol formaldehyde/epoxy hybrid resin) composites

To enhance the properties of epoxy composites, the biphenyl diol formaldehyde resin (BPFR) and glycidyloxypropyl polyhedral oligomeric silsesquioxane (G-POSS) were synthesized and used for modification of fiber-glass reinforced composites of epoxy resin (ER). The BPFR was employed to cure epoxy resin with different G-POSS contents and the laminates of fiber-glass reinforced hybrid composites prepared from BPFR, ER and G-POSS. The dynamic mechanical properties, thermal properties, mechanical and electrical properties of the hybrid composites were characterized by dynamic mechanical analyzer, thermogravimetric analyzer and electroproperty detector. The results showed that the T _g of the composites is increased with the addition of G-POSS. When the content of G-POSS is 5 wt%, the tensile and impact strength of the hybrid composites are 249.87 MPa and 63.83 kJ/m², respectively, which are all 30 % higher than those of non-added composites. At G-POSS content of 7 wt%, T _g of the material is 9.6 °C higher than pure BPFR/ER composite, and the initial decomposition temperature, T _id, is enhanced by about 29 °C. Dielectric constant, ε, and dielectric loss, tanδ, of the hybrid composites are between 0.53–0.7 and between 0.004–0.012, respectively.     

Preparation and thermal properties of bio‐based gallic acid epoxy/carbon nanotubes composites by cationic ring‐opening reaction

In order to prepare the bio‐based polymeric materials, a gallic acid epoxy resin (GA‐ER) is synthesized by using biodegradable gallic acid, and the nanocomposites of GA‐ER/glycidyl methacrylate (GMA)/multiwalled carbon nanotubes (MWCNTs) were prepared by dual hybrid cationic ring‐opening reaction. Differential scanning calorimetry (DSC) results show that the curing reaction temperature of the nanocomposites is between 150 and 225°C. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) results suggest that MWCNTs are homodispersing in the GA‐ER/GMA matrix when the MWCNTs content is not more than 1.0 wt%. The glass transition temperature of the nanocomposite with 0.5 wt% MWCNTs is 9.3°C higher than that of pure resin system. The initial thermal degradation temperature and degradation activation energies E_a of the nanocomposite with 1.0 wt% MWCNTs is 10°C and 68.6 kJ/mol higher than that the pure resin system, respectively. POLYM. COMPOS., 37:3093–3102, 2016. © 2015 Society of Plastics Engineers     

Octa(aminophenyl) polyhedral oligomeric silsesquioxane/boron‐containing phenol–formaldehyde resin nanocomposites: Synthesis,cured, and thermal properties

Octa(aminophenyl) polyhedral oligomeric silsesquioxane (OAP‐POSS) and boron‐containing phenol‐formaldehyde resin (BPFR) were synthesized, respectively. The BPFR nanocomposites with different OAP‐POSS content (wt%) were prepared, and their properties were characterized. The results show that the thermal degradation process of this nanocomposites can be divided into three stages, and they are all following the first order mechanism. The residual ratio and thermal degradation activation energy E_a of 9 wt% OAP‐POSS/BPFR nanocomposites are both better than others and the E_a increase gradually in three stages, which is 93.3, 134.0, and 181.9 kJ mol⁻¹, respectively. Its residual ratio at 900°C is 36.48%. The mechanical loss peak temperature T_p is 228°C for 12 wt% OAP‐POSSS/BPFR nanocomposites, which is higher 48°C than pure BPFR. POLYM. COMPOS., 2011. © 2011 Society of Plastics Engineers     

Synthesis of EP‐POSS mixture and the properties of EP‐POSS/epoxy,SiO2/epoxy,and SiO2/EP‐POSS/epoxy nanocomposite

The hybrid material of EP‐POSS mixture was synthesized by the hydrolysis and condensation of (γ‐glycidoxypropyl) trimethoxysilane. A series of binary systems of EP‐POSS/epoxy blends, epoxy resin modified by silica nanoparticles (SiO₂/epoxy), and ternary system of SiO₂/EP‐POSS/epoxy nanocomposite were prepared. The dispersion of SiO₂ in the matrices was evidenced by transmission electron micrograph, and the mechanical properties, that is, flexural strength, flexural modulus, and impact strength were examined for EP‐POSS/epoxy blends, SiO₂/epoxy, and SiO₂/EP‐POSS/epoxy, respectively. The fractured surface of the impact samples was observed by scanning electron micrograph. Thermogravimetry analysis were applied to investigate the different thermal stabilities of the binary system and ternary system by introducing EP‐POSS and SiO₂ to epoxy resin. The results showed that the impact strength, flexural strength, and modulus of the SiO₂/EP‐POSS/epoxy system increased around by 57.9, 14.1, and 44.0% compared with the pure epoxy resin, T_i, T_max and the residues of the ternary system were 387°C, 426°C, and 25.2%, increased remarkably by 20°C, 11°C and 101.6% in contrast to the pure epoxy resin, which was also higher than the binary systems. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 810‐819, 2013     

Organic–inorganic hybrid boron‐containing phenol–formaldehyde resin/SiO2 nanocomposites

The organic–inorganic hybrid boron‐containing phenol–formaldehyde (BPFR) resin/SiO₂ nanocomposites was synthesized in‐situ from boric acid, phenol, and tetramethoxysilane. The structure of BPFR modified and the distributions of silicon element were studied by Fourier‐transform infrared spectroscopy, energy dispersive X‐ray spectrometry, and transmission electron microscope, respectively. The glass transition temperature (T_g) was determined by torsional braid analysis. The results show that silicon element distribution is homogeneous, and the size of nanosilica is about 40–60 nm. The thermal stability and kinetics parameters of thermal degradation were determined by thermogravimetry analysis (TGA). TGA results show that the resin modified has higher heat resistance property when the additive quantity of SiO₂ was 3 wt%. The temperature of 5% weight loss is 487.7°C, which is 12.4°C higher than that of common BPFR. The residual ratio of 3 wt% SiO₂/BPFR was 62.3% at the temperature of 900°C, which is 11.2% higher than that of common BPFR. The mechanics loss peak T_p of 3% SiO₂/BPFR is 33°C higher than common BPFR. Fiberglass‐reinforced BPFR modified by 3 wt% SiO₂ has better mechanical and dielectric properties than that of common BPFR. POLYM. COMPOS., 2008. © 2007 Society of Plastics Engineers     

Curing behavior and thermal property of epoxy resin with boron‐containing phenol‐formaldehyde resin

The curing reaction of bisphenol‐A epoxy resin (BPAER) with boron‐containing phenol–formaldehyde resin (BPFR) was studied by isothermal and dynamic differential scanning calorimetry (DSC). The kinetic reaction mechanism in the isothermal reaction of BPAER‐BPFR was shown to follow autocatalytic kinetics. The activation energy in the dynamic cure reaction was derived. The influence of the composition of BPAER and BPFR on the reaction was evaluated. In addition, the glass transition temperatures (T_gs) were measured for the BPAER‐BPFR samples cured partially at isothermal temperatures. With the curing conditions varying, different glass transition behaviors were observed. By monitoring the variation in these T_gs, the curing process and the thermal property of BPAER–BPFR are clearly illustrated. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 1054–1061, 2000     

Mechanical properties and fracture behaviors of epoxy composites with phase‐separation formed liquid rubber and preformed powdered rubber nanoparticles: A comparative study

Epoxy composites filled with phase‐separation formed submicron liquid rubber (LR) and preformed nanoscale powdered rubber (PR) particles were prepared at different filler loading levels. The effect of filler loading and type on the rheological properties of liquid epoxy resin suspensions and the thermal and mechanical properties of the cured composites as well as the relative fracture behaviors are systematically investigated. Almost unchanged tensile yield strength of the cured epoxy/PR composites is observed in the tensile test compared with that of the neat epoxy; while the strength of the cured epoxy/LR composites shows a maximum value at ∼4.5 wt% and significantly decreases with increasing LR content. The glass transition temperature (T_g) of the cured PR/epoxy has shifted to the higher temperature in the dynamic mechanical thermal analysis compared with that of the cured pure epoxy and epoxy/LR composites. Furthermore, the presence of LR results in highly improved critical stress intensity factor (K_IC) of epoxy resin compared with the corresponding PR nanoparticles. In particular, the PR and LR particles at 9.2 wt% loading produce about 69 and 118% improvement in K_IC of the epoxy composites, respectively. The fracture surface and damage zone analysis demonstrate that these two types of rubber particles induce different degrees of local plastic deformation of matrix initiated by their debonding/cavitation, which was also quantified and correlated with the fracture toughness of the two epoxy/rubber systems. POLYM. COMPOS., 36:785–799, 2015. © 2014 Society of Plastics Engineers     

Preparation and properties of dopamine reduced graphene oxide and its composites of epoxy

To improve the thermal and mechanical properties and further to expand its applications of epoxy in electronic packaging, reduced graphene oxide/epoxy composites have been successfully prepared, in which dopamine (DA) was used as reducing agent and modifier for graphene oxide (GO) to avoid the environmentally harmful reducing agents and address the problem of aggregation of graphene in composites. Further studies revealed that DA could effectively eliminate the labile oxygen functionality of GO and generate polydopamine functionalized graphene oxide (PDA‐GO) because DA would be oxidated and undergo the rearrangement and intermolecular cross‐linking reaction to produce polydopamine (PDA), which would improve the interfacial adhesion between GO and epoxy, and further be beneficial for the homogenous dispersion of GO in epoxy matrix. The effect of PDA‐GO on the thermal and mechanical properties of PDA‐GO/epoxy composites was also investigated, and the incorporation of PDA‐GO could increase the thermal conductivity, storage modulus, glass transition (T_g), and dielectric constant of epoxy. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39754.     

Thermal and mechanical properties of liquid silicone rubber composites filled with functionalized graphene oxide

To improve the thermal and mechanical properties of liquid silicone rubber (LSR) for application, the graphene oxide (GO) was proposed to reinforce the LSR. The GO was functionalized with triethoxyvinylsilane (TEVS) by dehydration reaction to improve the dispersion and compatibility in the matrix. The structure of the functionalized graphene oxide (TEVS‐GO) was evaluated by Thermogravimetric analysis (TGA), Fourier transform infrared (FTIR) spectra, X‐ray diffraction (XRD), and energy dispersive X‐ray spectroscopy (EDX). It was found that the TEVS was successfully grafted on the surface of GO. The TEVS‐GO/LSR composites were prepared via in situ polymerization. The structure of the composites was verified by FTIR, XRD, and scanning electron microscopy (SEM). The thermal properties of the composites were characterized by TGA and thermal conductivity. The results showed that the 10% weight loss temperature (T₁₀) increased 16.0°C with only 0.3 wt % addition of TEVS‐GO and the thermal conductivity possessed a two‐fold increase, compared to the pure LSR. Furthermore, the mechanical properties were studied and results revealed that the TEVS‐GO/LSR composites with 0.3 wt % TEVS‐GO displayed a 2.3‐fold increase in tensile strength, a 2.79‐fold enhancement in tear strength, and a 1.97‐fold reinforcement in shear strength compared with the neat LSR. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42582.     

Studies of organoclays with functionalized pillaring agents

A series of clay pillaring agents with amino, olefin, and epoxy groups were synthesized. These pillaring agents were used to modify montmorillonite clay by ion‐exchange reactions. TGA studies showed that organoclays with imidazolium pillaring agents have a higher thermal stability than those with ammonium groups. The d‐spacings of organoclays were not affected by the pillaring agent functional groups and were sensitive to the size of pillaring agents. The dynamic‐mechanical properties of the resulting clay/epoxy composites determined by DMA were similar. The addition of these clays to this epoxy resin enhanced the T_g value of the resulting composites and greatly enhanced the storage moduli versus the pure epoxy resin by 1.6–1.8 times at 135°C. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Ultrasonic characterization of conductive epoxy resin/polyaniline composites

This study presents the ultrasonic characterization of conductive epoxy resin (ER)/polyaniline (PANI) composites. The prepared PANI is mixed with ER matrix at weight percentages of 5%, 10%, and 15% for preparing the ER/PANI composites. The effects of PANI amount on the mechanical properties of ER/PANI composites are investigated by ultrasonic pulse‐echo‐overlap method. Also, electrical conductivity, ultrasonic wave velocity and ultrasonic micro‐hardness values of ER/PANI composites are correlated. Experimental results show that there is an excellent correlation between ultrasonic micro‐hardness and ultrasonic shear wave velocity. Also, the results of ultrasonic velocities and elastic constants values illustrate that the appropriate combination ratio is 95 : 5 for ER and PANI in ER/PANI composites. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42748.     

A comparative study on the properties of the different amino‐functionalized multiwall carbon nanotubes reinforced epoxy resin composites

Multiwall carbon nanotubes (MWCNTs) were amino‐functionalized by 1,2‐ethylenediamine (EDA)' triethylenetetramine (TETA), and dodecylamine (DDA), and investigated by fourier transform infrared spectroscopy (FTIR), Raman spectroscopy, and thermogravimetric analysis (TGA). The dispersion of the DDA functionalized MWCNT in DMF is better than that of the MWCNT functionalized by the EDA and the TETA. Carbon nanotubes reinforced epoxy resin composites were prepared, and the effect of the amino‐functionalization on the properties of the composites was investigated by differential scanning calorimetry (DSC), dynamical mechanical analysis (DMA), and TGA. The composites reinforced by the MWCNTs demonstrate improvement in various mechanical properties. The increase of T_g of the composites with the addition of amino‐functionalized MWCNT compared to the T_g of the composites with the addition of unfunctionalized MWCNT was due to the chemical combination and the physical entanglements between amino group from modified MWNTs and epoxy group from the epoxy resin. The interfacial bonding between the epoxy and the amino group of the EDA and the TETA‐modified MWCNT is more important than the well dispersion of DDA‐modified MWCNT in the composites for the improvement of the mechanical properties. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Novel flame retardant thermosets from nitrogen‐containing and phosphorus‐containing epoxy resins cured with dicyandiamide

A novel phosphorus‐containing epoxy resin (EPN‐D) was prepared by addition reaction of 9,10‐dihydro‐9‐oxa‐10‐phosphaphenanthrene 10‐oxide (DOPO) and epoxy phenol‐ formaldehyde novolac resin (EPN). The reaction was monitored by epoxide equivalent weight (EEW) titration, and its structure was confirmed by FTIR and NMR spectra. Halogen‐free epoxy resins containing EPN‐D resin and a nitrogen‐containing epoxy resin (XT resin) were cured with dicyandiamide (DICY) to give new halogen‐free epoxy thermosets. Thermal properties of these thermosets were studied by differential scanning calorimeter (DSC), dynamic mechanical analysis (DMA), thermal mechanical analyzer (TMA) and thermal‐gravimetric analysis (TGA). They exhibited very high glass transition temperatures (T_gs, 139–175°C from DSC, 138–155°C from TMA and 159–193°C from DMA), high thermal stability with T_{d,5 wt %} over 300°C when the weight ratio of XT/EPN‐D is ≥1. The flame‐retardancy of these thermosets was evaluated by limiting oxygen index (LOI) and UL‐94 vertical test. The thermosets containing isocyanurate and DOPO moieties showed high LOI (32.7–43.7) and could achieve UL‐94 V‐0/V‐1 grade. Isocyanurate and DOPO moieties had an obvious synergistic effect on the improvement of the flame retardancy. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Hybrid multi‐scale epoxy composites containing conventional glass microfibers and electrospun glass nanofibers with improved mechanical properties

A mechanically flexible mat consisting of structurally amorphous SiO₂ (glass) nanofibers was first prepared by electrospinning followed by pyrolysis under optimized conditions and procedures. Thereafter, two types of hybrid multi‐scale epoxy composites were fabricated via the technique of vacuum assisted resin transfer molding. For the first type of composites, six layers of conventional glass microfiber (GF) fabrics were infused with the epoxy resin containing shortened electrospun glass nanofibers (S‐EGNFs). For the second type of composites, five layers of electrospun glass nanofiber mats (EGNF‐mats) were sandwiched between six layers of conventional GF fabrics followed by the infusion of neat epoxy resin. For comparison, the (conventional) epoxy composites with six layers of GF fabrics alone were also fabricated as the control sample. Incorporation of EGNFs (i.e., S‐EGNFs and EGNF‐mats) into GF/epoxy composites led to significant improvements in mechanical properties, while the EGNF‐mats outperformed S‐EGNFs in the reinforcement of resin‐rich interlaminar regions. The composites reinforced with EGNF‐mats exhibited the highest mechanical properties overall; specifically, the impact absorption energy, interlaminar shear strength, flexural strength, flexural modulus, and work of fracture were (1097.3 ± 48.5) J/m, (42.2 ± 1.4) MPa, (387.1 ± 9.9) MPa, (12.9 ± 1.3) GPa, and (30.6 ± 1.8) kJ/m², corresponding to increases of 34.6%, 104.8%, 65.4%, 33.0%, and 56.1% compared to the control sample. This study suggests that EGNFs (particularly flexible EGNF‐mats) would be an innovative type of nanoscale reinforcement for the development of high‐performance structural composites. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42731.     

Thermophysical properties of anhydride‐cured epoxy/nano‐clay composites

Polymer nano‐composites made with a matrix of anhydride‐cured diglycidyl ether of bisphenol A (DGEBA) and reinforced with organo‐montmorillonite clay were investigated. A sonication technique was used to process the epoxy/clay nano‐composites. The thermal properties of the nano‐composites were measured with dynamic mechanical analysis (DMA). The glass transition temperature T_g of the anhydride‐cured epoxy was higher than the room temperature (RT). For samples with 6.25 wt% (4.0 vol%) of clay, the storage modulus at 30°C and at (T_g + 15)°C was observed to increase 43% and 230%, respectively, relative to the value of unfilled epoxy. The clay reinforcing effect was evaluated using the Tandon‐Weng model for randomly oriented particulate filled composites. Transmission electron microscopy (TEM) examination of the nano‐composites prepared by sonication of clays in acetone showed well‐dispersed platelets in the nano‐composites. The clay nano‐platelets were observed to be well‐intercalated/expanded in the anhydride‐cured epoxy resin system. POLYM. COMPOS., 26:42–51, 2005. © 2004 Society of Plastics Engineers.     

Phenolic‐epoxy matrix curable by click chemistry—synthesis,curing, and syntactic foam composite properties

Alkyne functional phenolic resin was cured by azide functional epoxy resins making use of alkyne‐azide click reaction. For this, propargylated novolac (PN) was reacted with bisphenol A bisazide (BABA) and azido hydroxy propyloxy novolac (AHPN) leading to triazole‐linked phenolic‐epoxy networks. The click cure reaction was initiated at 40–65°C in presence of Cu₂I₂. Glass transition temperature (Tg) of the cured networks varied from 70°C to 75°C in the case of BABA‐PN and 75°C to 80°C in the case of AHPN‐PN. DSC and rheological studies revealed a single stage curing pattern for both the systems. The cured BABA‐PN and AHPN‐PN blends showed mass loss above 300°C because of decomposition of the triazole rings and the novolac backbone. Silica fiber‐reinforced syntactic foam composites derived from these resins possessed comparable mechanical properties and superior impact resistance vis‐a‐vis their phenolic resin analogues. The mechanical properties could be tuned by regulating the reactant stoichiometry. These low temperature addition curable resins are suited for light weight polymer composite for related applications. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41254.     

Properties of a reactive‐graphitic‐carbon‐nanofibers‐reinforced epoxy

Our previous studies showed that herringbone graphitic GNFs surface‐derivatized with reactive linker molecules bearing pendant primary amino functional groups capable of binding covalently to epoxy resins. Of special importance, herringbone GNFs derivatized with 3,4′‐oxydianiline (GNF‐ODA) were found to react with neat butyl glycidyl ether to form mono‐, di‐, tri‐, and tetra‐glycidyl oligomers covalently coupled to the ODA pendant amino group. The resulting reactive GNF‐ODA (butyl glycidyl)_n nanofibers, r‐GNF‐ODA, are especially well suited for reactive, covalent incorporation into epoxy resins during thermal curing. Based on these studies, nanocomposites reinforced by the r‐GNF‐ODA nanofibers at nanofiber loadings of 0.15–1.3 wt% were prepared. Flexural property of cured r‐GNF‐ODA/epoxy nanocomposites were measured through three‐point‐bending tests. Thermal properties, including glass transition temperature (T_g) and coefficient of thermal expansion (CTE) for the nanocomposites, were investigated using thermal mechanical analysis. The nanocomposites containing 0.3 wt% of the nanofibers gives the highest mechanical properties. At this 0.3‐wt% fiber loading, the flexural strength, modulus and breaking strain of the particular nanocomposite are increased by about 26, 20, and 30%, respectively, compared to that of pure epoxy matrix. Moreover, the T_g value is the highest for this nanocomposite, 14°C higher than that of pure epoxy. The almost constant change in CTEs before and after T_g, and very close to the change of pure epoxy, is in agreement with our previous study results on a chemical bond existing between the r‐GNF‐ODA nanofibers and epoxy resin in the resulting nanocomposites. POLYM. COMPOS., 28:605–611, 2007. © 2007 Society of Plastics Engineers     

Development of high Tg epoxy resin and mechanical properties of its fiber‐reinforced composites

A new epoxy resin with high glass transition temperature (T_g) (～ 180°C) and a viscosity low enough for infiltration into dry reinforcements at 40°C was developed for the vacuum‐assisted resin transfer molding process. To study the curing behavior and viscosity, several blends were formulated using multifunctional resin, aromatic hardener, and reactive diluents. Effects of these components on the viscosity and T_g were investigated by thermomechanical analysis, dynamic scanning calorimetry, and rheometer. Experimental results showed that a liquid aromatic hardener and multifunctional epoxy resin should be used to decrease the viscosity to <1 Pa·s at 40°C. Moreover, the addition of a proper reactive diluent decreased the viscosity and simultaneously minimized the deterioration of T_g. Mechanical properties of the composite produced with the optimized blend were evaluated at both room‐temperature and high‐temperature conditions. According to the results, the composite showed comparable mechanical properties with that of the current commercial resin. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Mechanical properties of epoxy resins reinforced with synthetic boehmite (AlOOH) nanosheets

In this article, sheet boehmite (AlOOH), which was synthesized via a facile and environmental friendly method, was used as reinforcing agent to toughen Bisphenol A epoxy resin. The result of X–ray Diffraction (XRD) and IR spectrum indicated that the as–synthesized product was pure crystalline and high purity AlOOH. The effects of sheet AlOOH on the mechanical properties of AlOOH/epoxy nanocomposites were investigated. The results indicated that the introduction of AlOOH significantly improved the mechanical properties of epoxy resin. Compared with neat epoxy resin, the tensile strength and the fracture toughness (K_IC) of the AlOOH/epoxy nanocomposites filled with 4 wt % AlOOH increased by 24.2% and 28.7%, respectively, while the flexural strength increased from 40.92 to 50.00 MPa. From Scanning Electron Microscope (SEM), a phase‐separated morphology and plenty of cervices and river branches were observed in the fractured surfaces of composites. With the increase of sheet AlOOH content, river‐shaped cracks became more and more intensive. Overall, the addition of sheet AlOOH is shown as a promising method for mechanical properties enhancement of epoxy matrix. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41409.     

Grafting multi-elements hybrid polymer brushes on graphene oxide for epoxy composite with excellent flame retardancy

In this paper, a silicon-oxygen coupling agent (MPS) with a double bond is hydrolyzed with graphene oxide (GO) to obtain MPS-GO. The polymerization of MPS-GO with the phosphorus-containing monomer (HEPO) is initiated with 2,2′-Azobis(2-methylpropionitrile) (AIBN) to obtain multi-elements hybrid polymer brushes grafting graphene oxide (HM-GO). As a flame retardant, different amounts of HM-GO are added to obtain EP composites. In this system, the properties of composite flame retardant obviously increase with the increasing of HM-GO. The limiting oxygen index (LOI) value of composites with 4 wt% addition of HM-GO is 31.0%, while the LOI value of EP-0 is only 23.9%. And the peak heat release rate (PHRR) value is reduced from 515.8 W g⁻¹ of pure epoxy resin to 376.9 W g⁻¹. In addition, with the increase of HM-GO addition, the T_g value, flexural strength and flexural modulus of EP composites are improved. Through calculation, it is proved that the rising of T_g was due to the increase of crosslink density of the system. The flame retardant performance and mechanical properties of the composite materials are steadily improved, indicating that such flame retardants are dispersed well in the epoxy resin. HM-GO is an efficient macromolecular modified graphene oxide halogen-free flame retardant, which can improve both flame retardant properties and mechanical properties.