Rheological behavior ‐ Electrical and thermal properties of polypyrrole/graphene oxide nanocomposites

Polypyrrole/graphene oxide (Ppy/GO) nanocomposites were synthesized via in situ polymerization of pyrrole in the presence of GO at various proportions (1–5%). They were characterized to determine their electrical, thermal, and rheological properties by various techniques. The aim of this study was to determine the rheological behavior of Ppy/GO nanocomposite at different mass ratios (100 : 1, 100 : 2, 100 : 3, 100 : 4, and 100 : 5%) and temperature (25–180°C) using a rotational mode in cone‐plate method. The shear stress (τ Pa) and viscosity (η Pa s) values of the nanocomposites increased with the increase in GO mass ratio added to Ppy, which was accompanied by an increased flexibility of the nanocomposites due to the higher aspect ratio of the GO sheet. Hence, it is suggested that the GO sheets are effective for the reinforcement of Ppy thereby significantly improvising its thermal stability, electrical conductivity, and rheological properties. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40642.     

Rheological assessment of variable molecular chain structures of linear low‐density polyethylene under reactive modification

The aim of this study was to investigate how changes in the molecular structure of linear low‐density polyethylene (LLDPE) during peroxide modification can be detected by a simple rheological method. For this purpose, a commercial‐grade LLDPE (Exxon Mobile LL4004EL) was reacted with different doses of dicumyl peroxide (DCP). The samples were analyzed by size exclusion chromatography coupled with a light‐scattering detector. With increasing DCP dose, at a roughly constant molar mass, an increasing number of long‐chain branches were found. The dynamic shear oscillatory measurements showed a deviation of the phase angle–complex shear modulus curve from that of the linear LLDPE, which was attributed to the presence of long‐chain branching. By the use of a simple rheological method that used melt rheology, transformations in the molecular architecture induced on the original LLDPE during the early stages of reactive modification were indicated. Reasonable and consistent estimates of the degree of long‐chain branching (x) and the volume fraction of the various molecular species produced in the peroxide modification of LLDPE were obtained. Various three‐dimensional plots were constructed to exhibit the correlation between the process parameters and x. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39617.     

New compatibilizer for linear low‐density polyethylene (LLDPE)/clay nanocomposites

Linear low‐density polyethylene (LLDPE) is one of the most widely used polymers in many fields, but it is difficult to prepare LLDPE/clay nanocomposites because of the hydrophobic nature of LLDPE. In this study, the effectiveness of low molecular weight trimethoxysilyl‐modified polybutadiene (Organosilane) as a compatibilizer for LLDPE/clay nanocomposites was studied using X‐ray diffraction (XRD) and correlated with mechanical properties. Organosilane is known to react with dicumyl peroxide (DCP) to form free radicals, which react with LLDPE increasing the polarity of the LLDPE. Based on XRD and mechanical tests, it was concluded that Organosilane is a good compatibilizer for LLDPE and clay. Also when Organosilane was used in preparing LLDPE/clay nanocomposite foams, most mechanical properties were improved. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Dynamic rheological behavior and mechanical properties of PVC/CPE/MAP–POSS nanocomposites

Poly(vinyl chloride)/chlorinated polyethylene (PVC/CPE)/methylacryloylpropyl‐containing polyhedral oligomeric silsesquioxane (MAP–POSS) nanocomposites are prepared. The plastic behavior and dynamic rheological behavior of PVC/CPE/MAP–POSS are investigated. The influences of composition on dynamic storage modulus G′, loss modulus G″, and complex viscosity η* of PVC/CPE/MAP–POSS melts are discussed. The dynamic mechanical properties, mechanical properties, and morphology are determined. The results show that both plastic time and balance torque of the nanocomposites decrease, but the G′, G″, and η* all increase with increasing MAP–POSS content. The maximum value of the dynamic mechanical loss tan δ decreases and elasticity increases when MAP–POSS is added. The impact strength of the nanocomposites increases with increasing MAP–POSS content and has the best value at 10% content of MAP–POSS, which is 5.38 kJ/m² higher than that of the blend without MAP–POSS. The MAP–POSS can be used as an efficient process aid and impact aid for the PVC/CPE blend. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

The properties (rheological,dielectric, and mechanical) and microtopography of spherical fullerene‐filled poly(arylene ether nitrile) nanocomposites

Poly (arylene ether nitrile)/fullerene (PEN/fullerene) nanocomposites were prepared by a facile solution‐cast method and the rheological, dielectric, mechanical, and morphological properties of the resulted nanocomposites were systematically studied and compared. Rheological studies showed PEN/fullerene nanocomposites percolation network formed at fullerene containing of 1.50 wt %, when the shear frequency was fixed at 0.1 Hz, the fitted rheological percolation threshold was about 1.55 wt %, very close to the experimental observations. The dielectric transaction occurs when the fullerene loading reached 1.50 wt %, that is very close to its rheological percolation threshold. At this point, PEN/fullerene nanocomposites also showed the optimal mechanical properties with a tensile strength of 93.6 MPa and modulus of 1951.5 MPa, which is increased by 27% and 15% compared with the pure PEN. SEM and TEM images have manifested the separate fullerene aggregated to fullerene bundles in PEN/fullerene nanocomposites, and the dispersion of fullerene bundles begin to go bad when the containing above 1.50 wt %. The PEN/fullerene nanocomposites can be widely used due to its excellent dielectric and mechanical performance. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40100.     

Microwave‐absorbing properties of linear low‐density polyethylene/ethylene–octene copolymer/carbonyl iron powder composites

Using linear low‐density polyethylene (LLDPE)/ethylene–octene copolymer (POE) as a polymer matrix and carbonyl iron powders (CIPs) as filler, we prepared polymer matrix composites with microwave‐absorbing properties by means of melt blending. Scanning electron microscopy and transmission electron microscopy were used to characterize the samples. The absorbing properties of the composites were measured with the arch method in the range of frequency 2.0–18.0 GHz. The results indicate that the absorbing peaks moved to low frequency as the CIP content in composites increased and that there was an appropriate CIP content in LLDPE/POE/CIP composites to achieve the best absorbing effectiveness. The electromagnetic parameters of the composites were determined with the transmission/reflection method in the range 2.6–17.8 GHz. The experimental results show that there were both dielectric loss and magnetic loss in the LLDPE/POE/CIP composites. Therefore, the microwave absorption of the LLDPE/POE/CIP composites was attributed to the combining contributions of the dielectric loss and magnetic loss. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Effects of titanate treatment on morphology and mechanical properties of graphene nanoplatelets/high density polyethylene nanocomposites

The effect of graphene nanoplatelets (GNPs) and titanate coupling agent on morphology and mechanical properties of high density polyethylene (HDPE) nanocomposites was investigated. The titanate has a tendency to link chemically with the two dissimilar species GNPs and HDPE via proton coordination to generate a complete continuous phase for stress/strain transfer via the elimination of air voids and hydrophobicity. The interaction of titanate with GNPs and HDPE was effective to improve the dispersion of GNPs in HDPE composites. At constant weight (1 wt %) of titanate treatment for 2 and 5 wt % HDPE composites, we clearly observed a significantly high value of tensile strength and elongation at break than untreated composites. Particularly, composite containing 2 wt % GNPs in HDPE with titanate showed 66.5% improvement of the ultimate tensile strength and an enormously high value of elongation at break. The effect of GNPs dispersion and orientation in HDPE for the mechanical reinforcement was also evaluated based on the experimental modulus data to theoretical predictions made using the Halpin‐Tsai model. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42073.     

Synthesis and characterization of linear low‐density polyethylene/sepiolite nanocomposites

Linear low‐density polyethylene (LLDPE)/sepiolite nanocomposites were prepared by melt blending using unmodified and silane‐modified sepiolite. Two methods were used to modify sepiolite: modification before heat mixing (ex situ) and modification during heat mixing (in situ). The X‐ray diffraction results showed that the position of the main peak of sepiolite remained unchanged during modification step. Infrared spectra showed new peaks confirming the development of new bonds in modified sepiolite and nanocomposites. SEM micrographs revealed the presence of sepiolite fibers embedded in polymer matrix. Thermogravimetric analysis showed that nanocomposites exhibited higher onset degradation temperature than LLDPE. In addition, in situ modified sepiolite nanocomposites exhibited higher thermal stability than ex situ modified sepiolite nanocomposites. The ultimate tensile strength and modulus of the nanocomposites were improved; whereas elongation at break was reduced. The higher crystallization temperature of some nanocomposite formulations revealed a heterogeneous nucleation effect of sepiolite. This can be exploited for the shortening of cycle time during processing. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Thermal properties and morphology of noncrosslinking linear low‐density polyethylene‐grafted acrylic acid

Noncrosslinking linear low‐density polyethylene‐grafted acrylic acid (LLDPE‐g‐AA) was prepared by melt‐reactive extrusion in our laboratory. The thermal behavior of LLDPE‐g‐AA was investigated by using differential scanning calorimetry (DSC). Compared with neat linear low‐density polyethylene (LLDPE), melting temperature (T_m) of LLDPE‐g‐AA increased a little, the crystallization temperature (T_c) increased about 4°C, and the melting enthalpy (ΔH_m) decreased with an increase in acrylic acid content. Isothermal crystallization kinetics of LLDPE and LLDPE‐g‐AA samples were carried out by using DSC. The overall crystallization rate of LLDPE was smaller than that of grafted samples. It showed that the grafted acrylic acid monomer onto LLDPE acted as a nucleating agent. Crystal morphologies of LLDPE‐g‐AA and LLDPE were examined by using SEM. Spherulite sizes of LLDPE‐g‐AA samples were lower than that of LLDPE. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 2626–2630, 2002     

Thermal and mechanical characterization of linear low‐density polyethylene/wood flour composites

A linear low‐density polyethylene (LLDPE) matrix was modified with an organic peroxide and by a reaction with maleic anhydride (MAn) and was simultaneously compounded with untreated wood flour in a twin‐screw extruder. The thermal and mechanical properties of the modified LLDPE and the resulting composites were evaluated. The degree of crystallinity was reduced in the modified LLDPE, but it increased with the addition of wood flour for the formation of the composites. Significant improvements in the tensile strength, ductility, and creep resistance were obtained for the MAn‐modified composites. This enhancement in the mechanical behavior could be attributed to an improvement in the compatibility between the filler and the matrix. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2775–2784, 2003     

Thermal,dielectric, and mechanical properties of SiC particles filled linear low‐density polyethylene composites

A thermally conductive linear low‐density polyethylene (LLDPE) composite with silicon carbide (SiC) as filler was prepared in a heat press molding. The SiC particles distributions were found to be rather uniform in matrix at both low and high filler content due to a powder mixing process employed. Differential scanning calorimeter results indicated that the SiC filler decreases the degree of crystallinity of LLDPE, and has no obvious influence on the melting temperature of LLDPE. Experimental results demonstrated that the LLDPE composites displays a high thermal conductivity of 1.48 Wm^?1 K^?1 and improved thermal stability at 55 wt % SiC content as compared to pure LLDPE. The surface treatment of SiC particles has a beneficial effect on improving the thermal conductivity. The dielectric constant and loss increased with SiC content, however, they still remained at relatively low levels (<10² Hz); whereas, the composites showed poorer mechanical properties as compared to pure LLDPE. In addition, combined use of small amount of alumina short fiber and SiC gave rise to improved overall properties of LLDPE composites. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Calendered linear low‐density polyethylene consolidated meat and bone meal composites

Bioplastics produced from meat and bone meal (MBM) suffer from rapid and drastic mechanical property deterioration because of their hydrophilic nature. This study investigates mechanical and water stability of composites produced from introduction of a minor component of a synthetic polyethylene as a binder phase to consolidate MBM. The milled and sieved MBM was compounded with 5–60 wt % linear low‐density polyethylene (LLDPE) and formed into composite sheets by calendering, which is an industrially relevant process. Results indicated that a minimum of 15 wt % LLDPE content was required to form a nominally continuous binder phase that allowed for good processability and environment stability of the composites. As expected, the water vapor permeability (WVP) and water absorption characteristics of the composites were intermediate between those of MBM and LLDPE. Sheets containing 15 wt % LLDPE absorbed up to 35 wt % water. Composites tested after being soaked in water showed an initial decrease in TS of about 30% for the first hour but then remained fairly unchanged in the next 72 hours, confirming their moderate environment stability. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 41145.     

Mechanical and fracture properties of halloysite nanotube reinforced vinyl‐ester nanocomposites

The mechanical and fracture properties of vinyl‐ester composites reinforced with halloysite nanotubes have been investigated. Enhancements in toughness are attributed to crack bridging, deflection, and localized plastic deformation, while strength improvements can be attributed to the large aspect ratio of fillers, favorable interfacial adhesion and dispersion, and inter‐tubular interaction. Comparisons of experimental data on elastic modulus and mathematical models for predicting particulate polymer composites have verified the models of Paul and Guth. The aspect ratio of fillers and the degree of interfacial adhesion are crucial factors in the prediction of elastic modulus in these polymer nanocomposites. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 1716–1725, 2013     

Thermal and mechanical properties of linear low‐density polyethylene/low‐density polyethylene/wax ternary blends

The thermal and mechanical properties of uncrosslinked three‐component blends of linear low‐density polyethylene (LLDPE), low‐density polyethylene (LDPE), and a hard, paraffinic Fischer–Tropsch wax were investigated. A decrease in the total crystallinity with an increase in both LDPE and wax contents was observed. It was also observed that experimental enthalpy values of LLDPE in the blends were generally higher than the theoretically expected values, whereas in the case of LDPE the theoretically expected values were higher than the experimental values. In the presence of higher wax content there was a good correlation between experimental and theoretically expected enthalpy values. The DSC results showed changes in peak temperature of melting, as well as peak width, with changing blend composition. Most of these changes are explained in terms of the preferred cocrystallization of wax with LLDPE. Young's modulus, yield stress, and stress at break decreased with increasing LDPE content, whereas elongation at yield increased. This is in line with the decreasing crystallinity and increasing amorphous content expected with increasing LDPE content. Deviations from this behavior for samples containing 10% wax and relatively low LDPE contents are explained in terms of lower tie chain fractions. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 1748–1755, 2005     

Effects of different compatibilizers on the rheological,thermomechanical, and morphological properties of HDPE/LLDPE blend‐based nanocomposites

The influence of two different compatibilizers and their combination (maleic anhydride grafted high density polyethylene, HDPE‐g‐MA; maleic anhydride grafted linear low density polyethylene, LLDPE‐g‐MA; and 50/50 wt % mixture of these compatibilizers) on the rheological, thermomechanical, and morphological properties of HDPE/LLDPE/organoclay blend‐based nanocomposites was evaluated. Nanocomposites were obtained by melt‐intercalation in a torque rheometer in two steps. Masterbatches (compatibilizer/nanoclay 2:1) were obtained and subsequently diluted in the HDPE/LLDPE matrix producing nanocomposites with 2.5 wt % of nanoclay. Wide angle X‐ray diffraction (WAXD), steady‐state rheological properties, and transmission electron microscopy (TEM) were used to determine the influence of different compatibilizer systems on intercalation and/or exfoliation process which occurs preferentially in the amorphous phase, and thermomechanical properties. The LLDPE‐g‐MA with a high melt index (and consequently low viscosity and crystallinity) was an effective compatibilizer for this system. Furthermore, the compatibilized nanocomposites with LLDPE‐g‐MA or mixture of HDPE‐g‐MA and LLDPE‐g‐MA exhibited better nanoclay's dispersion and distribution with stronger interactions between the matrix and the nanoclay. These results indicated that the addition of maleic anhydride grafted polyethylene facilitates both, the exfoliation and/or intercalation of the clays and its adhesion to HDPE/LLDPE blend. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 1726–1735, 2013     

Online ultrasonic film casting of LLDPE and LLDPE/clay nanocomposites

Transparent cast films of linear low density polyethylene (LLDPE) with nanoclay up to 10 wt % were prepared in one step process using an ultrasonically assisted compounding extruder operating at various ultrasonic amplitudes combined with film casting machine operating at various take up speeds. Thermal, rheological, morphological, and mechanical properties and gas permeability of these films were studied. Ultrasonic treatment introduced an increase in the complex viscosity and storage modulus and a reduction in the tangent loss of LLDPE/clay nanocomposite melts. Cast films prepared by ultrasonic treatment at an amplitude of 7.5 μm showed the highest mechanical properties in both the machine and transverse directions and the lowest oxygen permeability. X‐ray diffraction patterns along with the SEM and TEM images revealed the presence of the exfoliated structure due to the ultrasonic treatment for cast films containing up to 7.5 wt % of clay loading. NMR studies of LLDPE cast films showed an increase of branching due to the ultrasound treatment. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Additives for ultraviolet‐induced oxidative degradation of low‐density polyethylene

Polyethylene (PE) is one of the most widely produced and widely used plastics in the world. Saturated hydrocarbons cannot absorb the energy of the light reaching earth, so the degradation process is rather slow; this, in return, causes disposal problems. On the other hand, it was observed that in the presence of oxygen and impurities in the polymer matrix, the degradation could be reduced to shorter time intervals. In this study, vanadium(III) acetyl acetonate (VAc), serpentine (SE), and Cloisite 30B (CL) were used as additives, both together and alone, and we followed the photodegradation of PE. The amount of VAc was kept constant at 0.2 wt %, whereas the amounts of SE and CL were varied between 1 and 4 wt %. The samples were irradiated by UV light for up to 500 h. Mechanical and spectroscopic measurements were carried out during certain time intervals to monitor the degradation. VAc containing PE showed the fastest degradation. The elongation at break values of these samples were reduced to half of the initial value of elongation at break within five days. Combinations of the CL and SE additives were also proven to accelerate the degradation of PE; this was followed by an increase in the carbonyl index, which was observed to be at least 10 times greater than that of pure PE. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43354.     

Recycled milk pouch and virgin low‐density polyethylene/linear low‐density polyethylene based coir fiber composites

The viability of the thermomechanical recycling of postconsumer milk pouches [a 50 : 50 low‐density polyethylene/linear low‐density polyethylene (LDPE–LLDPE) blend] and their use as polymeric matrices for coir‐fiber‐reinforced composites were investigated. The mechanical, thermal, morphological, and water absorption properties of recycled milk pouch polymer/coir fiber composites with different treated and untreated fiber contents were evaluated and compared with those of virgin LDPE–LLDPE/coir fiber composites. The water absorption of the composites measured at three different temperatures (25, 45, and 75°C) was found to follow Fickian diffusion. The mechanical properties of the composites significantly deteriorated after water absorption. The recycled polymer/coir fiber composites showed inferior mechanical performances and thermooxidative stability (oxidation induction time and oxidation temperature) in comparison with those observed for virgin polymer/fiber composites. However, a small quantity of a coupling agent (2 wt %) significantly improved all the mechanical, thermal, and moisture‐resistance properties of both types of composites. The overall mechanical performances of the composites containing recycled and virgin polymer matrices were correlated by the phase morphology, as observed with scanning electron microscopy. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Effect of various alumina nano‐fillers on the thermal and mechanical behaviour of low‐density polyethylene–Al2O3 composites

Two different alumina powders were dispersed in low‐density polyethylene (LDPE) to evaluate if any role can be ascribed to the crystalline phase, size and morphology of the alumina filler. In particular a submicrometric α‐alumina and a nanocrystalline transition (γ/δ) alumina were added to the polymer at 5 wt% concentration, using a Brabender mixing unit. Both the neat inorganic fillers showed a good dispersibility in the polyolefin. The thermal and mechanical properties of the composites obtained were evaluated. As expected, a significant increase of the stiffness and abrasion resistance of LDPE was achieved in both cases. Furthermore, the composites showed a higher thermo‐oxidative stability with respect to neat LDPE. Independent of their crystalline phase, size and morphology, both fillers gave a similar enhancement of composite features. Copyright © 2010 Society of Chemical Industry     

Thermal,electrical, and mechanical properties of polyethylene–graphene nanocomposites obtained by in situ polymerization

In this study, we investigated the thermal, dynamic mechanical, mechanical, and electrical properties of polyethylene (PE)–graphene nanosheet (GNS) nanocomposites, with GNS amounts from 0 to 20 wt %, prepared by in situ polymerization. The thermal stability was evaluated by thermogravimetric analysis (TGA) and showed that the addition of GNSs to the polyolefin matrix increased the onset degradation temperature by 30°C. The electrical conductivity, measured by the impedance technique, presented a critical percolation threshold of 3.8 vol % (8.4 wt %) of GNS. A slight decrease in the tensile strength was found. On the other hand, dynamic mechanical analysis showed an increase in the storage modulus of the nanocomposites compared with that of neat PE. The glass‐transition temperature value increased from ?111°C (neat PE) to ?106°C (PE/6.6 wt % GNS). All of these results show that PE became stiffer and thermally more stable and could be transformed from an insulator to a semiconductor material in the presence of GNSs. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013