Mechanical and thermal properties of modified red mud‐reinforced phenolic foams

A new type of composite based on phenolic foams reinforced with red mud microparticles was prepared using a thermal foaming method. Red mud was ground into ultrafine particles with grain diameters ranging from 1 to 1.5 μm. Silane coupling agent γ‐ureidopropyltriethoxysilane was used to modify the red mud microparticles to improve particle dispersion and adhesion between the particles and the phenolic matrix. The effects of the modified red mud microparticles on the mechanical and thermal properties of the composite were investigated at weight ratios ranging from 0 to 21%. The phenolic foams incorporating 15 wt% of the filler exhibited the best integrated performance. In comparison with native phenolic foams, tensile strength and impact strength were increased by 81.8 and 82.3%, respectively. Furthermore, the addition of modified red mud microparticles to the phenolic foam significantly decreased its thermal conductivity while increasing its limiting oxygen index. A morphological analysis using scanning electron microscopy indicated that incorporation of the modified red mud microparticles into the foam produced relatively small and uniformly sized cells within the material, which indicated that the observed improvements in mechanical and thermal properties were primarily due to the chemical adhesion between the particles and the matrix and good dispersion of particles in the matrix. The reinforced foams described in this study can be used in a variety of applications in the field of heat insulation. © 2018 Society of Chemical Industry     

High‐temperature‐resistant polyimide/montmorillonite nanocomposite foams by solid blending

A series of high‐temperature‐resistant polyimide/montmorillonite (PI/MMT) nanocomposite foams were prepared by solid blending method. The dispersion of MMT and effects of MMT content on the properties of the PI/MMT nanocomposite foams were investigated. Results indicated that MMT could be exfoliated effectively and dispersed uniformly in the PI matrix by the solid blending method. The introduction of MMT could considerably increase the reduced compressive strength, thermal resistance, and decrease the dielectric constant of the PI/MMT nanocomposite foams. The reduced compressive strength of nanocomposite foams showed a maximum value at the MMT content of 5 wt%, which was 197% higher than that of pure PI foams. It was worth noting that a significant increase in glass‐transition temperature (T _g) could be achieved with the increase of MMT content, and the maximum T _g was as high as 436°C at the MMT content of 7 wt%. This study may provide a useful method to prepare PI/MMT nanocomposite foams with improved properties for targeted high‐temperature applications. POLYM. ENG. SCI., 2011. ©2011 Society of Plastics Engineers     

The toughening effect and mechanism of styrene‐butadiene rubber nanoparticles for novolac resin

In this article, phenolic nanocomposites were prepared using styrene–butadiene rubber (SBR) nanoparticles with an average particle size of about 60 nm as the toughening agent. The mechanical and thermal properties of phenolic nanocomposites and the toughening mechanism were studied thoroughly. The results showed that when adding 2.5 wt % SBR nanoparticles, the notched impact strength of phenolic nanocomposites reached the maximum value and was increased by 52%, without sacrificing the flexural performance. Meanwhile, SBR nanoparticles had no significant effect on the thermal decomposition temperature of phenolic nanocomposites. The glass‐transition temperature (T_g) of phenolic nanocomposites shifted to a lower temperature accompanying with the increasing T_g of loaded SBR, which showed there was a certain compatibility between SBR nanoparticles and phenol‐formaldehyde resin (PF). Furthermore, the analysis of Fourier transform infrared spectroscopy and X‐ray photoelectron spectroscopy indicated that there existed a weak chemical interaction between SBR nanoparticles and the PF matrix. The certain compatibility and weak chemical interaction promoted the formation of a transition layer and improved the interfacial bonding, which might be important reasons for the great enhancement of the toughness for phenolic nanocomposites. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41533.     

Conducting polymerized high‐internal‐phase emulsion/single‐walled carbon nanotube nanocomposite foams: Effect of the aqueous‐phase surfactant type on the morphology and conductivity

Poly(styrene‐co‐divinylbenzene)/single‐walled carbon nanotubes (SWCNTs) polymerized high‐internal‐phase emulsion (polyHIPE) nanocomposite foams were successfully synthesized with various types of aqueous‐phase surfactants. The effects of anionic, cationic, nonionic, and mixed surfactants on the morphology and electrical conductivity of the resulting nanocomposite foams were investigated. The use of an anionic surfactant, sodium dodecylbenzesulfonate (SDBS), did not completely result in the typical polyHIPE nanocomposite foam microstructure because of the partial instability of the high‐internal‐phase emulsion. The nanocomposite foams synthesized by nonionic surfactants, that is, Pluronic F127 and Triton X‐100, and the cationic/anionic mixture, cetyltrimethylammonium bromide/SDBS, exhibited the proper morphology, but the resulting nanocomposite foams were electrically insulators. Interestingly, the use of a Gemini‐like surfactant, sodium dioctylsulfosuccinate (SDOSS), significantly improved both the typical morphology and electrical properties of the resulting nanocomposite foams because of the probable stronger interactions of SDOSS molecules with SWCNTs. The typical morphology of the nanocomposite foam synthesized with the SDOSS/F127 mixed surfactant was significantly improved, but the electrical conductivity decreased to some extent compared with the SDOSS‐synthesized nanocomposite foams. This behavior was attributed to an increase in the tunneling length of the electrons between adjacent SWCNTs. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43883.     

A novel polyurethane prepolymer as toughening agent: Preparation,characterization, and its influence on mechanical and flame retardant properties of phenolic foam

A novel phosphorus‐ and silicon‐containing polyurethane prepolymer (PSPUP) was synthesized by the chemical reaction of phenyl dichlorophosphate with hydroxy‐terminated polydimethylsiloxane (HTPDMS) and subsequently with toluene‐2,4‐diisocyanate. The structure of PSPUP was confirmed by Fourier transform infrared spectroscopy and ¹H nuclear magnetic resonance. Afterward, a series of phenolic foams (PF) with different loadings of PSPUP toughening agent were prepared. The apparent density and scanning electron microscopy results showed that the addition of PSPUP can increase the apparent density of phenolic foam. The compressive, impact and friability test results showed that the incorporation of PSPUP into PF dramatically improved the compressive strength, impact strength, and reduced the pulverization ratio, indicating the excellent toughening effect of PSPUP. The limiting oxygen index of PSPUP modified phenolic foams remained a high value and the UL‐94 results showed all samples can pass V0 rating, indicating the modified foams still had good flame retardance. The thermal properties of the foams were investigated by thermogravimetric analysis under air atmosphere. Moreover, the thermal degradation behaviors of the PF and PSPUP/PF were investigated by real‐time Fourier transform infrared spectra. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Morphology and tensile properties of crosslinked nanocomposite foams of low‐density polyethylene and poly(ethylene‐co‐vinyl acetate) blends

This paper studies the morphology and tensile properties of nanocomposite foams of blends of low‐density polyethylene (LDPE) and poly(ethylene‐co‐vinyl acetate) (EVA). Preparations of LDPE/EVA nanocomposites were conducted in an internal mixer, and then samples were foamed via a batch foaming method. Morphology of the nanocomposite blends and nanocomposite foams was studied by X‐ray diffraction, transmission electron microscopy, and scanning electron microscopy. Morphological observations showed that nanoparticle dispersion in the polymeric matrix was affected by the blend ratio in a way such that EVA‐rich samples had a better dispersion of nanoclay than LDPE‐rich ones. In addition, the tensile properties of the nanocomposite foams were related to different variables such as blend ratio, clay content, and foam density. J. VINYL ADDIT. TECHNOL., 2010. © 2010 Society of Plastics Engineers     

Preparation and properties of a novel flame retardant polyurethane quasi‐prepolymer for toughening phenolic foam

A novel phosphorus‐ and nitrogen‐containing polyurethane quasi‐prepolymer (PNPUQP) was synthesized and incorporated into phenolic foam (PF) in different ratios in order to improve the toughness. The structure of PNPUQP was confirmed by Fourier transform infrared (FTIR) spectroscopy and nuclear magnetic resonance (NMR). The effects of PNPUQP on the flame retardant properties, thermal stability and mechanical properties of modified PF were investigated. The results suggested that the addition of 3 wt % PNPUQP increased the toughness of PF and improved the flame retardancy. The investigation on the morphology of PF and modified PF by scanning electron microscope (SEM) certified the good toughness of the PNPUQP on PF. Additionally, the thermal properties of the foams were investigated by thermogravimetric analysis (TGA) under N₂ atmosphere. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42424.     

Six‐arm star‐shaped polymer with cyclophosphazene core and poly(ε‐caprolactone) arms as modifier of epoxy thermosets

A six‐arm star‐shaped poly(ε‐caprolactone) (s‐PCL) based on cyclophosphazene core was obtained by presynthesis of a hydroxy‐teminated cyclophosphazene derivative and subsequent initiation of the ring‐opening polymerization of ε‐caprolactone, and its use in different proportions as toughening modifier of diglycidylether of bisphenol A/anhydride thermosets was studied. The star‐shaped polymer was characterized to have approximately 30 caprolactone units per arm. Differential scanning calorimetry revealed a nonsignificant influence on the curing process of the epoxy‐anhydride formulation by the addition of s‐PCL. The s‐PCL‐modified epoxy thermosets exhibited a great improvement in both toughness and strength compared with the neat resin, as the result of a joint effort by the internal rigid core and the external ductile polyester chains of s‐PCL. When the addition of the modifier was 3 wt %, an optimal mechanical and thermomechanical performance was achieved. The impact resistance and tensile strength of the cured epoxy resin were enhanced by 150% and 30%, respectively. The glass transition temperature was also increased slightly. Moreover, the addition of the star‐shaped modifier had little harmful effect on the thermal stability of the material. Thus s‐PCL was proved to be a superior toughening agent without sacrificing thermal and mechanical properties of the thermosets. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44384.     

Thermal‐Insulation,Electrical, and Mechanical Properties of Highly‐Expanded PMMA/MWCNT Nanocomposite Foams Fabricated by Supercritical CO2 Foaming

Foaming behavior of poly(methyl methacrylate) (PMMA)/multi‐walled carbon nanotubes (MWCNTs) nanocomposites and thermally‐insulating, electrical, and mechanical properties of the nanocomposite foams are investigated. PMMA/MWCNT nanocomposites containing various amounts of MWCNTs are first prepared by combining solution and melt blending methods, and then foamed using CO₂. The foaming temperature and MWCNT content are varied for regulating the structure of PMMA/MWCNT nanocomposite foams. The electrical conductivity measurement results show that MWCNTs have little effect on the electrical conductivity of foams with large expansion ratio. Thermal conductivities of both solid and foamed PMMA/MWCNT nanocomposites are measured to evaluate their thermally insulating properties. The gas conduction, solid conduction, and thermal radiation of the foams are calculated for clarifying the effects of cellular structure and MWCNT content on thermal insulation properties. The result demonstrates that MWCNTs endowed foams with enhanced thermal insulation performance by blocking thermal radiation. Moreover, the compressive testing shows that MWCNTs improve the compressive strength and rigidity of foams. This research is essential for optimizing environmentally friendly thermal insulation nanocomposite foams with enhanced thermal‐insulation and compressive mechanical properties.     

Effect of zinc oxide on properties of phenolic foams/halogen‐free flame retardant system

A halogen‐free flame retardant system consisting of ammonium polyphosphate (APP) as an acid source, blowing agent, pentaerythritol (PER) as a carbonific agent and zinc oxide (ZnO) as a synergistic agent, was used in this work to enhance flame retardancy of phenolic foams. ZnO was incorporated into flame retardant formulation at different concentrations to investigate the flammability of flame retardant composite phenolic foams (FRCPFs). The synergistic effects of ZnO on FRCPFs were evaluated by limited oxygen index (LOI), thermogravimetric analysis (TGA), cone calorimeter tests, and images of residues. Results showed that the flame retardant significantly increased the LOI of FRCPFs. Compared with PF, heat release rate (HRR), total heat release (THR), effective heat of combustion (EHC), production or yield of carbon monoxide (COP or COY) and Oxygen consumption (O₂C) of FRCPFs all remarkably decreased. However specific extinction area (SEA) and total smoke release (TSR) significantly increased, which agreed with the gas‐phase flame retardancy mechanism of the flame retardant system. The results indicated that FRCPFs have excellent fire‐retardant performance and less smoke release. And the bending and compression strength were decreased gradually with the increase of ZnO. The comprehensive properties of FRCPFs were better when the amount of ZnO was 1～1.5%. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42730.     

Preparation,characterization, and improvement of hollow epoxy particle‐toughened vinyl ester composites for high‐end applications

Spherical hollow epoxy particles (HEPs) that can serve as advanced reinforcing fillers for vinyl ester thermosets were prepared using the water‐based emulsion method. The HEP fillers were incorporated into the vinyl ester matrices at different loading amounts, ranging from 0 to 9 wt %, to reinforce and toughen the vinyl ester composite. The optimum mechanical properties of the HEP‐toughened epoxy composite can be achieved by the addition of 5 wt % HEP filler into the vinyl ester matrices. The toughening and strengthening of the epoxy composites involved the interlocking of vinyl ester resins into the pore regions on the HEP fillers. The toughening and interlocking mechanisms of HEP‐toughened vinyl ester composites were also proposed and discussed. The addition of HEP fillers into vinyl ester matrices increased the glass transition temperature (T_g) and thermal stability of the composites. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Mechanical and thermal properties of phenolic/glass fiber foam modified with phosphorus‐containing polyurethane prepolymer

Phenolic foam exhibits outstanding flame, smoke and toxicity properties, good insulation properties and low production costs. However, the brittleness and pulverization of phenolic foam have severely limited its application in many fields. In this study, a novel phosphorus‐containing polyurethane prepolymer (DOPU) modifier was firstly synthesized, and then the foaming formula and processing of toughening phenolic foam modified with DOPU and glass fiber were explored. The structure and reactive behavior of prepolymer and phenolic resin were investigated using Fourier transform infrared spectroscopy. The effects of DOPU and glass fiber on the apparent density, compressive strength, bending strength and water absorption were investigated. The results suggested that the apparent density, compressive strength and bending strength of modified phenolic foam tended to increase irregularly with increasing content of DOPU. The addition of DOPU led to lower water absorption of glass fiber‐filled foam. Thermal stability and flame retardancy were examined using thermogravimetric analysis and limiting oxygen index (LOI) tests. It was found that foam with 3% DOPU and 0.5% glass fiber added exhibited good thermal stability and high char yields. The LOI value of modified phenolic foams decreased with increasing DOPU content, but it still remained at 41.0% even if the amount of modifier loaded was 10 wt%. © 2012 Society of Chemical Industry     

An experimental and theoretical investigation of the compressive properties of multi-walled carbon nanotube/poly(methyl methacrylate) nanocomposite foams

Polymer nanocomposite foams are promising low density substitutes for nanocomposites. Carbon nanotube/polymer nanocomposite foams possess high strength, low density, and can be made conductive. Good control of foam properties is of great importance in the application of such materials. In the current study, multi-walled carbon nanotubes (MWNTs) with controlled aspect ratio were used to alter the foam morphology in MWNT/poly(methyl methacrylate) (PMMA) nanocomposite foams produced by a supercritical carbon dioxide (CO₂) foaming process. It was found that with the addition of one weight percent of MWNTs, the Young’s modulus of polymer foams increased by as much as 82%, and the collapse strength increased by as much as 104%. The influence of MWNT aspect ratio on the compressive properties of nanocomposite foams was investigated. The addition of MWNTs influenced the foam properties in two ways: improving the compressive properties of the solid matrix, and reducing the bubble size of the nanocomposite foams. A modified constitutive model for predicting the compressive properties of high density closed-cell polymer foams was developed. The influence of the bubble size on the mechanical properties of polymer foams was discussed based on the new model.     

Evaluation of toughening mechanisms of polypropylene/ethylene–octene copolymer/maleic anhydride‐grafted poly(ethylene‐co‐octene)/clay nanocomposite

The toughness of a polypropylene (PP)/ethylene‐octene copolymer (EOC)/maleic anhydride‐grafted poly(ethylene‐co‐octene) (EOC‐g‐MA)/clay nanocomposite and blends of PP/EOC and PP/EOC/EOC‐g‐MA was investigated using Charpy impact and single‐edge‐notch tensile (SENT) tests. In order to understand the toughening mechanisms, impact fracture surfaces and damage zones of single‐edge‐notch samples were studied with scanning electron microscopy and transmission optical microscopy, respectively. It was observed that the addition of EOC‐g‐MA to PP/EOC blend led to improvements in both impact strength and fracture energy of SENT tests because of the enhanced compatibility of the blend, which resulted from reduced EOC particle size and improved interfacial adhesion, and the decreased crystallinity of PP. The incorporation of clay to PP/EOC/EOC‐g‐MA blend caused a further increase of the toughness, owing to the greater decrease in the size of elastomer particles, to the presence of clay tactoids inside the elastomer phase and presumably to debonding of clay layers during the low‐speed SENT tests. The results of microscopic observations showed that the main toughening mechanism in PP/EOC/EOC‐g‐MA blend and PP/EOC/EOC‐g‐MA/clay nanocomposite is crazing. Copyright © 2012 Society of Chemical Industry     

Bio‐nanocomposite films based on cellulose nanocrystals filled polyvinyl alcohol/chitosan polymer blend

Bio‐nanocomposite films based on polyvinyl alcohol/chitosan (PVA/CS) polymeric blend and cellulose nanocrystals (CNC) were prepared by casting a homogenous and stable aqueous mixture of the three components. CNC used as nanoreinforcing agents were extracted at the nanometric scale from sugarcane bagasse via sulfuric acid hydrolysis; then they were characterized and successfully dispersed into a PVA/CS (50/50, w/w) blend to produce PVA/CS–CNC bio‐nanocomposite films at different CNC contents (0.5, 2.5, 5 wt %). Viscosity measurement of the film‐forming solutions and structural and morphological characterizations of the solid films showed that the CNC are well dispersed into PVA/CS blend forming strong interfacial interactions that provide an enhanced load transfer between polymer chains and CNC, thus improving their properties. The obtained bio‐nanocomposite films are mechanically strong and exhibit improved thermal properties. The addition of 5 wt % CNC within a PVA/CS blend increased the Young's modulus by 105%, the tensile strength by 77%, and the toughness by 68%. Herein, the utilization of Moroccan sugarcane bagasse as raw material to produce high quality CNC has been explored. Additionally, the ability of the as‐isolated CNC to reinforce polymer blends was studied, resulting in the production of the aforementioned bio‐nanocomposite films with improved properties. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42004.     

Relationship between structure and properties in high‐performance PA6/SEBS‐g‐MA/(PPO/PS) blends: The role of PPO and PS

This work aimed at studying the role of poly(phenylene oxide) (PPO) and polystyrene (PS) in toughening polyamide‐6 (PA6)/styrene‐ethylene‐butadiene‐styrene block copolymer grafted with maleic anhydride (SEBS‐g‐MA) blends. The effects of weight ratio and content of PPO/PS on the morphology and mechanical behaviors of PA6/SEBS‐g‐MA/(PPO/PS) blends were studied by scanning electron microscope and mechanical tests. Driving by the interfacial tension and the spreading coefficient, the “core–shell” particles formed by PPO/PS (core) and SEBS‐g‐MA (shell) played the key role in toughening the PA6 blends. As PS improved the distribution of the “core–shell” particles due to its low viscosity, and PPO guaranteed the entanglement density of the PPO/PS phase, the 3/1 weight ratio of PPO/PS supplied the blends optimal mechanical properties. Within certain range, the increased content of PPO/PS could supply more efficient toughening particles and bring better mechanical properties. Thus, by adjusting the weight ratio and content of PPO and PS, the PA6/SEBS‐g‐MA/(PPO/PS) blends with excellent impact strength, high tensile strength, and good heat deflection temperature were obtained. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45281.     

Surface‐modified MgO nanoparticle enhances the mechanical and direct‐current electrical characteristics of polypropylene/polyolefin elastomer nanodielectrics

Polypropylene (PP)/polyolefin elastomer (POE) blends and MgO/PP/POE nanocomposites were fabricated by melt blending. The morphology, mechanical, and electrical properties of the nanocomposites were investigated. Scanning electron microscopy showed that the surface‐modified MgO nanoparticles were well dispersed in the polymer matrix at low loadings of less than 3 phr. X‐ray diffraction demonstrated that the crystalline phases of PP in the composites were changed and that the β phase significantly increased. An examination of the electrical properties revealed that the direct‐current (dc) electric breakdown strength and space‐charge suppression effect were remarkably improved by the introduction of the surface‐modified MgO nanoparticles. In addition, obvious enhancements in the tensile modulus and strength were obtained as a result of the synergistic toughening of the POE and MgO nanoparticles. Thus, MgO/PP/POE nanocomposites with enhanced mechanical and electrical properties have great potential to be used as recyclable insulation materials for high‐voltage dc cables with large transmission capacities and high operating temperatures. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 132, 42863.     

Effects of multi‐walled carbon nanotube functionalization on the morphological and mechanical properties of nanocomposite foams based on poly(vinyl chloride)/(wood flour)/ (multi‐walled carbon nanotubes)

Experimental results are presented for nanocomposite foams based on unplasticized poly(vinyl chloride)/(wood flour)/(multi‐wall carbon nanotubes) (PVC/WF/MWCNTs). The nanocomposite samples were prepared in an internal mixer and foamed via a batch processing method using compression molding. Nanoparticles were functionalized by sodium hypochlorite solution, and the functionalization process was monitored by Fourier‐transform infrared spectroscopy. The effects of MWCNTs (both neat and functionalized) and blowing agent concentration on the morphological properties (cell size and cell density) and mechanical properties (tensile and flexural strength) of the foam samples were studied. The results revealed that foam cell sizes decreased and cell densities increased with addition of MWCNTs. The dispersion of nanoparticles in the PVC medium was increased by functionalization, and the morphological properties of the foams containing functionalized nanoparticles were improved. Density of nanocomposite foams decreased more with functionalized MWCNTs as compared to other samples. Chemical blowing agent concentration had no significant effect on sample density. Mechanical properties of the samples were improved by using functionalized MWCNTs in comparison with those of foams without this component. J. VINYL ADDIT. TECHNOL., 18:161–167, 2012. © 2012 Society of Plastics Engineers     

In situ polymerization of polyurethane‐silver nanocomposite foams with intact thermal stability,improved mechanical performance,and induced antimicrobial properties

Silver nanoparticle‐reinforced thermoplastic polyurethane (PU/AgNP) nanocomposite foams were prepared using in situ polymerization techniques in accordance with DOW chemicals’ industrial standards. The foams exhibited improved mechanical performance, induced antimicrobial properties, and intact stability when subjected to a thermal degradation treatment. Scanning electron microscopy (SEM) indicated a homogeneous dispersion of the silver nanoparticle (AgNP) within the polymeric matrix at low filler loadings and a cluster formation at higher loadings. SEM also indicated the agglomeration of the silver nanofiller particles as a result of the thermal degradation treatment, which caused them to lose their nanoscopic characteristics and act as ordinary silver metal. Molecular modeling techniques were used to explain these observations and confirmed the higher repulsive interactions between the polymer chains and the silver nanoparticles with the increase in the nanofiller content. Stress relaxation of the nanocomposites showed optimum mechanical performance and lowest hysteresis for the 0.1% AgNP nanocomposites due to the confinement of the PU chains between the large number of the nanoparticles. Incubation with 0.1% foam inhibited the growth of Klebseilla spp. and Escherichia coli and to some extent Staphylococcus spp. This is very interesting as the same nanocomposite loaded with 0.1% AgNp has also shown the best mechanical performance highlighting the strong action of this “unclustered” low concentration on both the material and biomedical sides. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43125.     

Effect of compatibilizer and silane coupling agent on physical properties of ethylene vinyl acetate copolymer/ethylene‐1‐butene copolymer/clay nanocomposite foams

In this study an attempt was made to obtain lower density of ethylene‐vinyl acetate copolymer (EVA)/ethylene‐1‐butene copolymer (EtBC) foams without sacrificing mechanical properties. For this purpose EVA/EtBC/clay nanocomposite foams were prepared. To investigate the effect of compatibilizer and silane coupling agent on the physical properties of the EVA/EtBC/clay foams, maleic anhydride‐grafted EtBC (EtBC‐g‐MAH) and the most commonly used silane coupling agent in rubbers, bis(3‐triethoxysilylpropyl) tetrasulfide (Si‐69) were used in the preparation of EVA/EtBC/clay nanocomposite foams. The formation of EVA/EtBC/clay nanocomposite foams was supported by X‐ray diffraction results. And, using a compatibilzer and silane coupling agent, lower density of EVA/EtBC/clay nanocomposite foams were obtained without sacrificing mechanical properties except compression set. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 3259–3265, 2006