The Effect of Epoxidized Sunflower Oil on the Miscibility of Plasticized PVC/NBR Blends

Blends of plasticized poly(vinyl chloride) (PVC) with several ratios of nitrile rubber (NBR) were studied. The effects of epoxidized sunflower oil (ESO) in combination with di-(2-ethylhexyl)phthalate (DEHP) in the PVC blends on the tensile strength, elongation, hardness, and dynamical mechanical analysis (DMA) were studied. The modulus and hardness results revealed that the addition of ESO to the blend favors the miscibility of PVC and NBR. The PVC/NBR/(DEHP-ESO) blends behave as a compatible system as is evident from the single T _g observed in DMA. The moderate level broadening of the T _g zone in blends is due to the presence of ESO in the plasticizer system. Blends of plasticized PVC and nitrile rubber showed promising properties. The ESO is suitable to partially replace DEHP in PVC/NBR blends.     

Nitrile rubber/hindered phenol exterminated hyperbranched polyester materials with improved damping and mechanical performance

Hindered phenol exterminated hyperbranched polyester (mHBP) is fabricated by esterification reaction. The mHBP is introduced into nitrile rubber (NBR) to prepare NBR/mHBP blends. Structure, damping and mechanical properties of NBR/mHBP blends are investigated by Fourier transform infrared spectroscopy (FTIR), ¹H‐NMR, dynamic mechanical thermal analyzer (DMTA), and tensile tester. FTIR spectra of the blends illustrate the intermolecular hydrogen bonding between the NBR and mHBP, contributing to the improvement of damping and mechanical properties. The results indicate that, with the increasing mHBP content, the T_g of the blends shifted to a higher temperature with a broadening temperature range and improved mechanical properties, showing an application in adjusting the T_g and temperature range without decreasing of loss factor. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42605.     

Morphological,thermal, and mechanical properties of poly(vinyl chloride)/acrylonitrile butadiene rubber blend using CuSO4·5H2O as cross‐linking agent

Novel rigid poly(vinyl chloride) (PVC)/cross‐linked acrylonitrile butadiene rubber (NBR) blend using copper (II) sulfate pentahydrate (CuSO₄·5H₂O) as cross‐linking agent was prepared by melt mixing. Fourier transform infrared analysis showed that the coordination cross‐linking occurred between NBR and CuSO₄·5H₂O in the PVC matrix, in which a novel morphology was first observed by scanning electron microscopy analysis. The thermal stability and degradation behavior of the PVC/NBR/CuSO₄·5H₂O blend were examined by means of dynamic mechanical thermal analysis and thermogravimetric analysis. It was found that the glass‐transition temperature (T_g) of the PVC/NBR/CuSO₄·5H₂O blend was enhanced by adding the coordination cross‐linked NBR into the PVC matrix. In spite of the onset decomposition temperature and the first rapidest decomposition temperature of the resultant blends reduced in comparison to neat PVC, the second rapidest decomposition temperature and the residues of the resultant blends were significantly enhanced. In addition, the thermal degradation kinetics and mechanical properties of the resultant blends were also investigated. POLYM. ENG. SCI., 54:1864–1870, 2014. © 2013 Society of Plastics Engineers     

Development and characterization of reactively extruded PVC/polystyrene blends

PVC/PS blends are obtained through a reactive extrusion–polymerization method by the absorption of a solution of styrene monomer, initiator, and a crosslinking agent in commercial suspension‐type porous polyvinyl chloride (PVC) particles, forming a dry‐blend with a relatively high monomer content. These PVC/styrene dry‐blends are reactively polymerized in a twin‐screw extruder in the melt state. They do not contain monomer residues as detected by GC. The transparency, fracture surface morphology, thermal stability, rheology and static and dynamic mechanical properties of these blends are compared to physical PVC/PS blends at similar compositions. Owing to the high polymerization temperature (180°C), short PS chains are formed in the reactive extrusion process. These short chains are dispersed both as a separate phase of ～2 μm particles (recognized by SEM) and also as molecularly dispersed chains enhancing plasticization and compatibilization. The molecularly dispersed short PS chains tend to plasticize the PVC phase, reducing its melt viscosity and glass transition temperature. The content of the short PS chains forming the dispersed separate PS particles is too low for DMTA to detect a separate T_g. Thus, reactively extruded PVC/PS blends exhibit single T_g transitions at lower temperatures compared with the neat PVC. Migration of the PVC's low‐molecular‐weight additives (lubricants and thermal stabilizer) to the PS phase is observed in the physical PVC/PS blends, causing antiplasticization of the PS phase. This results in both reduction of the T_g and an increase in the thermal stability of the PS phase in the physical PVC/PS blends. Comparing TGA thermograms of reactively extruded and physical PVC/PS indicates that the PS formed in the extruder is different from the commercial PS. This can stem from various chemical reactions that can take place in the studied reactive polymerization process. Polym. Eng. Sci. 44:1473–1483, 2004. © 2004 Society of Plastics Engineers.     

Effect of cloisite 30B on the thermal and tensile behavior of poly(butylene adipate-co-terephthalate)/poly(vinyl chloride) nanoblends

Ternary PBAT/PVC/C30B nanoblends were successfully prepared via melt blending process at 130 °C and characterized by different techniques. The properties of the elaborated PBAT/PVC/C30B nanoblends were compared with those of the nonfilled PBAT/PVC blends to examine the C30B effects on the structure and properties of PBAT/PVC/C30B nanoblends. FTIR spectra revealed the presence of specific interactions between C=O of PBAT and acidic hydrogen of PVC, supporting the formation of miscible nanoblends. The PBAT/PVC/C30B morphology was investigated by both X-ray diffraction and transmission electron microscopy analyses. It was suggested the formation of mixed intercalated/partially exfoliated structures. Differential scanning calorimetry thermograms of PBAT/PVC/C30B nanoblends exhibited a single T _g and a full disappearance of the PBAT melting endotherm, confirming the complete compatibilization between PVC and PBAT. It was found that the T _g of the nanoblends were higher than those of the pristine blends due to their mixed intercalated/partially exfoliated structures. PBAT and PVC chains would be confined in a same C30B gallery causing a reduction of the chain mobility. Nanoblends showed a reduction of their thermal stability compared to their pristine blends, as a result of the catalytic effect of the C30B in the thermal degradation process. Tensile measurements displayed an improvement of mechanical properties for the ternary PBAT/PVC/C30B nanoblends relative to their virgin blends due to the insertion of clay particles into composite matrix.     

Mechanical Properties and Thermooxidative Aging of a Ternary Blend,Pvc/Enr/Nbr,Compared with the Binary Blends of Pvc

In the quest to improve the thermooxidative aging of the poly(vinyl chloride)/epoxidized natural rubber (PVC/ENR) blend, nitrile rubber (NBR) was incorporated into the blend to yield a ternary blend of PVC/ENR/NBR. A Brabender Plasticorder with a mixing attachment was used to perform the melt mixing at 150°C and 50 rpm followed by compression molding. The mechanical properties, dynamic mechanical properties, and thermooxidative aging behavior of the ternary blend were compared with those of the binary blends (i.e., PVC/ENR and PVC/NBR). It was found that the ternary blend exhibits mechanical properties which are superior to those of PVC/ENR. A single glass transition temperature (T _g) obtained from dynamic mechanical analysis coupled with synergism in the modulus and some other mechanical properties indicate that PVC, ENR, and NBR form a single phase (miscible system) in the ternary blend. Di-2-ethyl hexylphthalate (DOP) plasti-cizer improves the aging resistance of the blends generally, whereas the presence of CaCO₃ as a filler only imparts minor influences on the properties and aging resistance of the blends.     

Compatibility of poly(butadiene‐co‐acrylonitrile) with poly(L‐lactide) and poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate)

Poly(L ‐lactide) (PLLA) and poly(3‐hydrobutyrate‐co‐3‐hydroxyvalerate) (PHBV) were blended with poly(butadiene‐co‐acrylonitrile) (NBR). Both PLLA/NBR and PHBV/NBR blends exhibited higher tensile properties as the content of acrylonitrile unit (AN) of NBR increased from 22 to 50 wt %. However, two separate glass transition temperatures (T_g) appeared in PLLA/NBR blends irrespective of the content of NBR, revealing that PLLA was incompatible with NBR. In contrast, a single T_g, which shifted along with the blend composition, was observed for PHBV/NBR50 blends. Moreover NBR50 suppressed the crystallization of PHBV, indicating that PHBV was compatible with NBR50. Decrease of both elongation modulus and stress at maximum load was less significant and increase of elongation at break was more pronounced in PHBV/NBR50 blends than in PLLA/NBR50 blends. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 3508–3513, 2004     

Preparation and characterization of biodegradable polymer blends from poly(3‐hydroxybutyrate)/poly(vinyl acetate)‐modified corn starch

Biodegradable polymer blends prepared by blending poly(3‐hydroxybutyrate) (PHB) and corn starch do not form intact films due to their incompatibility and brittle behavior. For improving their compatibility and flexibility, poly(vinyl acetate) (PVAc) was grafted from the corn starch to prepare the PVAc‐modified corn starch (CSV). The resulting CSV consisted of 47.2 wt% starch‐g‐PVAc copolymer and 52.8 wt% PVAc homopolymer and its structure was verified by FT‐IR analysis. In comparison with 35°C of the neat PVAc, the glass transition temperature (T_g) of the grafted PVAc chains on starch‐g‐PVAc was higher at 44°C because of the hindered molecular mobility imposed from starch on the grafted PVAc. After blending PHB with the CSV, structure and thermal properties of the blends were investigated. Only a single T_g was found for all the PHB/CSV blends and increased with increasing the CSV content. The T_g‐composition dependence of the PHB/CSV blends was well‐fitted with the Gordon‐Taylor equation, indicating that the CSV was compatible with the PHB. In addition, the presence of the CSV could raise the thermal stability of the PHB component. It was also found that the presence of the PHB and PVAc components would not hinder the enzymatic degradation of the corn starch by α‐amylase. POLYM. ENG. SCI., 55:1321–1329, 2015. © 2015 Society of Plastics Engineers     

Gas permeation of polymer blends. II. Poly(vinyl chloride)/acrylonitrile–butadiene copolymer (NBR) blends

The transport behavior of He, O₂, N₂, and CO₂ in a series of PVC/NBR polymer blends with varying acrylonitrile (AN) content in the NBR component has been studied at 25° and 50°C. In addition, measurements of density, crystallinity, and thermal expansion coefficients were carried out. The transport behavior of these blends is similar to previous result for PVC/EVA.¹. With increasing AN content in NBR, the permeability (P) and diffusivity (D) of the permeants decreased while the activation energy for diffusion (E_D) increased. For the polymer blends, better additivity of permeability and diffusivity was observed with increasing AN content in the NBR component. The polymer blends also showed increasing volume contraction with increasing AN content in the NBR component. These effects have been discussed as due mainly to increased polymer–polymer interaction causing reduced segmental mobility and increased compatibility of the two polymers. The sorption values calculated from P/D ratios were largely irregular and fluctuated with the blend composition. They were less reproducible than other transport parameters, i.e., P and D measured separately. Several reasons for the irregular sorption behavior were proposed.     

Morphological,mechanical, and rheological studies of PVC/ABS blends in the presence of maleic anhydride

A novel method of enhancing compatibility in PVC/ABS blends is the use of ABS‐grafted‐(maleic anhydride) (ABS‐g‐MAH) as a compatibilizer. In this study, maleic anhydride was grafted onto ABS (initiated by peroxide) in an internal mixer. Grafting degree was determined by a back‐titration method, and certain amounts of the resultant ABS‐g‐MAH were added to PVC/ABS blends during their melt blending in the mixer. The weight ratio of PVC to ABS was kept at 70:30. Evaluation of compatibilization was accomplished via tensile and notched Izod impact tests, scanning electron microscopy (SEM), and rheological studies. According to the SEM micrographs, better dispersion of the rubber phase and its finer size in properly compatibilized blends were indications of better compatibility. Besides, in the presence of a proper amount [5 parts per hundred parts of PVC (php)] of ABS‐g‐MAH, PVC/ABS blends showed significantly higher impact strengths than uncompatibilized blends. This result, in turn, would be an indication of better compatibility. In the presence of 5 php of compatibilizer, the higher complex viscosity and storage modulus, as well as a lower loss modulus and loss factor in the range of frequency studied, indicated stronger interfacial adhesion as a result of interaction between maleic anhydride and the PVC‐SAN matrix. J. VINYL ADDIT. TECHNOL., 2010. © 2010 Society of Plastics Engineers     

Thermal stability and compatibility of epoxy/polycarbonate and epoxy/tetramethyl polycarbonate blends

A series of the blends of tetrafunctional epoxy resins with polycarbonate (PC) or tetramethyl polycarbonate (TMPC) was prepared to investigate thermal stability and compatibility. The T_g behavior as a function of isothermal curing time was observed. The thermal stability of epoxy and epoxy/thermoplastics blends was estimated using thermogravimetric analysis (TGA). Fourier transform infrared (FTIR) investigation demonstrated the occurrence of thermal degradation and hydrolysis in epoxy and epoxy/PC blends during the curing process. The thermal degradation of cured epoxy was induced with etherification, a sort of side reaction, and resulted in the chain scission of networks leading to the decrease of T_g. The variance of thermal stability with a combination of two components in these blends resulted from the difference of the compatibility due to chemical structure similarity. The compatibility was corroborated with the morphology by scanning electron microscopy (SEM). © 1996 John Wiley & Sons, Inc.     

Effect of poly(epichlorohydrin) on the thermal and mechanical properties of poly(vinyl chloride)

Five kinds of polyepichlorohydrin (PECH) of different molecular weights were synthesized and characterized by gel permeation chromatography (GPC). Mechanical blending was used to mix PECH and poly(vinyl chloride) (PVC) together. The blends of different PVC/PECH ratios were characterized by thermogravimetric analysis (TGA), tensile tests, differential scanning calorimetry (DSC), and dynamic mechanical analysis (DMA). TGA results show the thermal stability of PVC/PECH blends is desirable. Tensile tests indicate elongation at break is raised by increasing both the amount and the molecular weight of PECH. DSC is used to determine the glass transition temperature of PECH, and a quite low T_g is obtained. DMA results indicate that PECH has a perfect compatibility with PVC, when PECH concentration is below 20 wt %. There is only one peak in each tan δ curve, and the corresponding T_g decreases as PECH amount increases. However, above 20 wt %, phase separation takes place. The molecular weight of PECH also has a great influence on the glass transition temperature of the blends. This study shows that PECH is an excellent plasticizer for PVC, and one can tailor the glass transition temperature and tensile properties by changing the amount and the molecular weight of PECH. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Thermal,morphological, and physicomechanical properties of (chlorinated polyethylene rubber)/(chloroprene rubber) blends

The effect of the blend ratio on the thermal, morphological, and physicomechanical properties of (chlorinated polyethylene rubber)/(chloroprene rubber) (CPE/CR) blends was studied. Two distinct glass transition temperatures (T_g) of all blends were observed in differential scanning calorimetry curves, falling between the T_g of the two pure rubbers. Analysis of the blends by scanning electron microscopy showed both dispersed and continuous phase morphology that depended on the blend composition. Thermogravimetric analysis showed that all the compounds underwent two stages of thermal degradation. The Mooney viscosity and optimum cure times increased with the increase in CPE contents, whereas the scorch times decreased. The tensile strength and elongation at break decreased, whereas the 100% modulus, hardness, and compression set increased with the increase of CPE content; the tear strength had the lowest value for the 50/50 CPE/CR blend because of the poor miscibility. The results from thermal aging and oil resistance tests showed that pure CPE possessed better thermal aging property and oil resistance than those of pure CR. Thus, considerable improvement in oil resistance of the blend compounds was achieved with the increase of CPE content. J. VINYL ADDIT. TECHNOL., 21:18–23, 2015. © 2014 Society of Plastics Engineers     

Effect of poly(vinyl chloride)/chlorinated polyethylene blend composition on thermal stability

Blends of poly(vinyl chloride) (PVC) with different ratios of chlorinated polyethylene (CPE) were degradated by the thermogravimetric method under dynamic conditions (50–600°C) in an inert atmosphere. The effect of the miscibility and composition of the PVC/CPE blends on the thermal stability were investigated. DSC curves of the blends show neither a shift of the PVC glass transition temperature nor a shift of the CPE melting temperature, which means that these blends are heterogeneous. The characteristics of the TG curves were determined, some of which (T_1%,T_5%, Δm₁) can be used as indicators of the thermal stability of the blend. The apparent activation energy of PVC dehydrochlorination in the blends was also calculated. Comparison of the experimental TG curves and TG curves predicted by the additivity rule indicates the existence of the components' interaction in the PVC/CPE blends. The addition of CPE improves the thermal stability of PVC for all the investigated blends in the temperature range where α_calc is greater than α_exp. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 166–172, 2000     

Thermal decomposition of cellulose/synthetic polymer blends containing grafted products. II. Cellulose/polyacrylonitrile blends

The homogeneous grafting of acrylonitrile onto cellulose was carried out in a dimethyl sulfoxide/paraformaldehyde solvent system. The grafted products were added to cellulose/polyacrylonitrile (PAN) blends as compatibilizers. The thermal decomposition behavior of the blends was investigated by thermogravimetry. The thermal stability of the blends with higher grafted product content was lower by more than 100°C than that of the blends without grafted product. The accessibility values of the former blends were larger than those of the latter. The microphase-separated structures of the grafted product blends were finer than those without the product. Dynamic mechanical measurements and differential scanning calorimetry were performed to estimate the glass transition temperatures, T_g, of the blends. The variation in T_g was smaller than that in characteristic temperatures determined by thermogravimetry. The difference in thermal decomposition behavior was correlated to that in compatibility. Thermogravimetry was found to be effective for estimating the compatibility in cellulose/PAN blends containing grafted products. © 1996 John Wiley & Sons, Inc.     

Properties and morphologies of elastomer blends modified with EPDM‐g‐poly[2‐dimethylamino ethylmethacrylate]

The graft copolymerization of 2‐dimethylamino ethylmethacrylate (DMAEMA) onto ethylene propylene diene mononer rubber (EPDM) was carried out in toluene via solution polymerization technique at 70°C, using dibenzoyl peroxide as initiator. The synthesized EPDM rubber grafted with poly[DMAEMA] (EPDM‐g‐PDMAEMA) was characterized with ¹H‐NMR spectroscopy, gel permeation chromatography (GPC), differential scanning calorimetry (DSC), and thermal gravimetric analysis (TGA). The EPDM‐g‐PDMAEMA was incorporated into EPDM/butadiene acrylonitrile rubber (EPDM/NBR) blend with different blend ratios, where the homogeneity of such blends was examined with scanning electron microscopy and DSC. The scanning electron micrographs illustrate improvement of the morphology of EPDM/NBR rubber blends as a result of incorporation of EPDM‐g‐PDMAEMA onto that blend. The DSC trace exhibits one glass transition temperature (T_g) for EPDM/NBR blend containing EPDM‐g‐PDMAEMA, indicating improvement of homogeneity. The physico‐mechanical properties after and before accelerated thermal aging of the homogeneous, and inhomogeneous EPDM/NBR vulcanizates with different blend ratios were investigated. The physico‐mechanical properties of all blend vulcanizates were improved after and before accelerated thermal aging, in presence of EPDM‐g‐PDMAEMA. Of all blend ratios under investigation EPDM/NBR (75/25) blend possesses the best physico‐mechanical properties together with the best (least) swelling (%) in brake fluid. Swelling behavior of the rubber blend vulcanizates in motor oil and toluene was also investigated. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Compatibilization of poly(vinyl chloride) and polystyrene blends with poly(styrene‐co‐n‐methylolacrylamide)

In this work, the compatibilization of blends of plasticized polyvinyl chloride (PVC) and polystyrene (PS) with poly(styrene‐co‐n‐methylolacrylamide) (PSnMA) was investigated. The PSnMA was synthesized by emulsion polymerization with different amounts of n‐methylolacrylamide (nMA). Particle size and phase behavior was determined by scanning electron microscopy, and mechanical properties were determined in an Universal Testing Machine. Micrographs revealed that an appreciable size reduction of the dispersed phase was achieved when small amounts of PSnMA were added to the blend, and as the amount of nMA was increased, particle size decreased. When the (PVC/PS/PSnMA) blend was subjected to solvent extraction to remove PS and unreacted PVC, the residue showed a single T_g. Tensile modulus and the ultimate strength of the blends increased with PSnMA content. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Effect of the molecular weight on the plasticization properties of poly(hexane succinate) in poly(vinyl chloride) blends

Blends of poly(vinyl chloride) (PVC) and poly(hexane succinate) (PHS) with various molecular weights were analyzed with respect to their mechanical properties, durability, and thermal stability. We found that the molecular weight of PHS played an important role in the plasticizing process, and the single glass-transition temperature (T _g) of the PVC blends measured by dynamic mechanical analysis supported the complete miscibility between PHS and PVC. The plasticizing efficiency of PHS increased as the molecular weight increased; this reflected the gradually increasing elongation at break and the decreased T _g of the PVC blend. Meanwhile, the higher molecular weight of PHS also improved the resistance of migration and thermal stability but decreased the biodegradability of the PVC blends; this was due to the strong intermolecular interactions between PHS and PVC. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47081.     

Mechanical,thermal, and water uptake characteristics of woodflour‐filled polyvinyl chloride/acrylonitrile butadiene styrene blends

Woodflour‐filled composites based on polymeric blends of polyvinyl chloride (PVC) and super high‐impact grade ABS were developed. Mechanical, thermal, and water uptake characteristics of the PVC/ABS matrix and their wood composites were evaluated. In the case of PVC/ABS matrix, the blend at a mass ratio of 50/50 rendered the impact strength with a very high value of up to 65 kJ/m², noticeably higher than those of the parent resins, that is, 6 kJ/m² of PVC and 35 kJ/m² of ABS. Dynamic mechanical analysis thermograms showed two distinct glass transition temperatures (T_gs) that shifted toward each other indicating partial miscibility of the blends. Water absorption of the blends after 24 h immersion was low, that is, within the range of 0.04–0.2 wt % and exhibits a behavior closed to pseudo‐Fickian type. The obtained PVC/ABS wood composites exhibited an increase of flexural modulus as well as T_gs with an increase of woodflour content. Finally, impact strength of the PVC/ABS composites was significantly higher than those of PVC composites or polyethylene composites comparing at the same woodflour content. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Studies on polyblends of poly(vinyl chloride) and acrylonitrile-butadiene-styrene terpolymer

Blends of poly (vinyl chloride) (PVC) and acrylonitrile-butadiene styrene (ABS) terpolymer were prepared in different ratios by a melt blending technique. ABS containing three different levels of rubber content were used. A quantitative assessment of ABS in PVC/ABS blends has been shown by infrared studies. ABS content has been shown as the presence of the characteristic acrylonitrile peak. Differential scanning calorimetry (DSC) studies have been carried out to study the glass transition (T_g) behavior of the blends. Two T_g values corresponding to PVC and styrene-acrylonitrile (SAN) copolymer have been observed. Thermogravimetric analysis (TGA) reveals a significant improvement in thermal stability of these blends as compared to PVC. Mechanical properties show a significant increase in the impact strength which is related to rubber content of the ABS used. Morphological studies have been carried out by scanning electron microscopy which support the observation that an increase in rubber content results in greater ductility.