Effect of cloisite 30B clay and sisal fiber on dynamic mechanical and fracture behavior of unsaturated polyester toughened epoxy network

This study examined the dynamic mechanical properties of sisal fiber reinforced unsaturated polyester (UP) toughened epoxy nanocomposites. The chemical structures changes in Epoxy, UP and UP toughened epoxy (Epoxy/UP) systems were characterized by Proton Nuclear magnetic resonance (¹HNMR) spectroscopy. The morphological alterations of the nanocomposites were analyzed by X‐ray diffraction (XRD) and transmission electron microscopy (TEM). The untreated, chemically treated fibers, nanoclays, and the fiber reinforced Epoxy/UP nanocomposites were confirmed by FTIR spectrometer. The obtained mechanical results showed that alkali‐silane treated fibers improve the tensile strength (96%) and flexural strength (60%) of the Epoxy/UP nanocomposite than that of Epoxy/UP blend due to the strong interfacial bonding between the sisal fiber and matrix. The fracture toughness (K_IC) and fracture energy (G_IC) of treated sisal fiber reinforced DGEBA/UP/C30B nanocomposites found to be higher than that of untreated sisal fiber nanocomposites. The dynamic mechanical analysis (DMA) reveals that the fiber reinforced Epoxy/UP nanocomposites contains 30 wt% treated fiber and 1 wt% nanoclays, exhibits the highest storage modulus and better glass transition temperature (T_g) among the other kind of systems. The surface morphology of the fibers, fractured surface of the resins and composites were confirmed by scanning electron microscope (SEM). POLYM. COMPOS., 37:2832–2846, 2016. © 2015 Society of Plastics Engineers     

Influence of complexing treatment and epoxy resin coating on the properties of aramid fiber reinforced natural rubber

In this work, natural rubber/aramid fiber (NR/AF) composites were prepared with master batch method. AF was modified by using epoxy resin (EP) and accelerator 2‐ethyl‐4‐methylimidazole (2E4MZ) through surface coating on the basis of the complexing treatment with CaCl₂ solution. Hydroxyl‐terminated liquid isoprene rubber (LIR) was regarded as a compatibilizer between EP and NR. It is found that the crystallinity on AF surface is decreased by complexing reaction with CaCl₂ solution. Swelling and mechanical properties of the vulcanized composites, such as swelling degree, tensile and tear strength, tensile modulus at 300% elongation, are measured, and the tensile fracture morphology and dynamic mechanical analysis of the composites are investigated. The results show that the mechanical properties of composites with modified fibers are improved obviously and interfacial adhesion between matrix and the fiber is enhanced, especially for the AF coated with EP and imidazole. The best comprehensive mechanical properties of the composites are obtained with using CaCl₂‐EP/2E4MZ system when the ratio of m(EP)/m(AF) is 3%. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42122.     

Kevlar fiber–epoxy adhesion and its effect on composite mechanical and fracture properties by plasma and chemical treatment

Kevlar 49 fibers were surface-modified by NH₃-, O₂-, and H₂O-plasma etching and chlo-rosulfonation and subsequent reaction with some reagents (glycine, deionized water, eth-ylendeiamine, and 1-butanol) to improve the adhesion to epoxy resin. After these treatments, the changes in fiber topography, chemical compositions of the fiber surfaces, and the surface functional groups introduced to the surface of fibers were identified by SEM, XPS, and static SIMS. Interlaminar shear strength (ILSS) and T-peel strenght between the fiber and opoxy resin, as measured by the short-beam test and T-peel test, were remarkedly improved by gas plasma and chlorosulfonation (0.1% and 0.25% CISO₃H at 30 s). However, from the results of similar G_IC values of the treated and untreated fiber composites, it is clear that the fiber/matrix interfacial bond strength is only a minor contributor to G_IC. SEM was also used to study the surface topography of the fracture surfaces of composites in T-peel test. It could be seen from SEM observations that the improvement of fiber/matrix interfacial bond strength often accompanied a change in fracture mode from the interface of fiber/epoxy resins to the fiber fibrillation and the resins. © 1996 John Wiley & Sons, Inc.     

Fabrication of amido group functionalized carbon quantum dots and its transparent luminescent epoxy matrix composites

Functional amido groups are modified onto the surface of carbon quantum dots (CQDs) in order to provide reactive groups. The modified CQDs are subsequently added into amine cured epoxy resin system. After curing reaction, transparent and luminescent composites are obtained. The modified CQDs are denoted as CQDs@NH₂, and composites studied in this article are denoted as CQDs@NH₂/epoxy. It is found that the dispersion of CQDs@NH₂ in epoxy matrix is effectively improved with the bridge of covalent bonding interface. As a result, the homogenously dispersed CQDs@NH₂ reduce light scattering. And more than double increased transparency and eightfold enhanced luminescence of CQDs@NH₂/epoxy are obtained compared with original CQDs@COONa/epoxy composites. This composite has potential for encapsulating materials in white light‐emitting diodes. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42667.     

Unsaturated polyester‐toughened epoxy composites: Effect of sisal fiber on thermal and dynamic mechanical properties

In the present study, the mechanical and thermal properties of sisal fiber‐reinforced unsaturated polyester (UP)‐toughened epoxy composites were investigated. The sisal fibers were chemically treated with alkali (NaOH) and silane solutions in order to improve the interfacial interaction between fibers and matrix. The chemical composition of resins and fibers was identified by using Fourier‐transform infrared spectroscopy. The UP‐toughened epoxy blends were obtained by mixing UP (5, 10, and 15 wt%) into the epoxy resin. The fiber‐reinforced composites were prepared by incorporating sisal fibers (10, 20, and 30 wt%) within the optimized UP‐toughened epoxy blend. Scanning electron microscopy was used to analyze the morphological changes of the fibers and the adhesion between the fibers and the UP‐toughened epoxy system. The results showed that the tensile and flexural strength of (alkali‐silane)‐treated fiber (30 wt%) ‐reinforced composites increased by 83% and 55%, respectively, as compared with that of UP‐toughened epoxy blend. Moreover, thermogravimetric analysis revealed that the (alkali‐silane)‐treated fiber and its composite exhibited higher thermal stability than the untreated and alkali‐treated fiber systems. An increase in storage modulus and glass transition temperature was observed for the UP‐toughened epoxy matrix on reinforcement with treated fibers. The water uptake behavior of both alkali and alkali‐silane‐treated fiber‐reinforced composites is found to be less as compared with the untreated fiber‐reinforced composite. J. VINYL ADDIT. TECHNOL., 23:188–199, 2017. © 2015 Society of Plastics Engineers     

High-performance composite from epoxy and glass fibers: Morphology,mechanical, dynamic mechanical,and thermal analysis

Diglycidyl ether of bisphenol-A type epoxy resin cured with diamino diphenyl sulfone was used as the matrix for fiber-reinforced composites to get improved mechanical and thermal properties for the resulting composites. E-glass fiber was used for fiber reinforcement. The morphology, tensile, flexural, impact, dynamic mechanical, and thermal properties of the composites were analyzed. The tensile, flexural, and impact properties showed dramatic improvement with the addition of glass fibers. Dynamic mechanical analysis was performed to obtain the T_g of the cured matrix as well as the composites. The improved thermal stability of the composites was clear from the thermogravimetric analysis. Scanning electron micrographs were taken to understand the interfacial adhesion between the fiber and the matrix. The values of mechanical properties were compared with modified epoxy resin composite system. Predictive models were applied using various equations to compare the mechanical data obtained theoretically and experimentally. POLYM. COMPOS., 2009. © 2008 Society of Plastics Engineers     

The interfacial strength and fracture characteristics of ethanol and polymer modified carbon nanotube fibers in their epoxy composites

Carbon nanotube (CNT) fibers spun from CNT arrays were used as the reinforcement for epoxy composites, and the interfacial shear strength (IFSS) and fracture behavior were investigated by a single fiber fragmentation test. The IFSS between the CNT fiber and matrix strongly depended on the types of liquid introduced within the fiber. The IFSS of ethanol infiltrated CNT fiber/epoxy varied from 8.32 to 26.64 MPa among different spinning conditions. When long-molecule chain or cross-linked polymers were introduced, besides the increased fiber strength, the adhesion between the polymer modified fiber and the epoxy matrix was also significantly improved. Above all, the IFSS can be up to 120.32 MPa for a polyimide modified CNT fiber, one order of magnitude higher than that of ethanol infiltrated CNT fiber composites, and higher than those of typical carbon fiber/epoxy composites (e.g. 60–90 MPa). Moreover, the composite IFSS is proportional to the tensile strength and modulus of the CNT fiber, and decreases with increasing fiber diameter. The results demonstrate that the interfacial strength of the CNT fiber/epoxy can be significantly tuned by controlling the fiber structure and introducing polymer to optimize the tube–tube interactions within the fiber.     

Enzyme‐mediated surface modification of jute and its influence on the properties of jute/epoxy composites

Surface modification of jute fibers is necessary to improve the adhesion and interfacial compatibility between fibers and resin matrix before using fibers in polymer composites. In this study, dodecyl gallate (DG) was enzymatically grafted onto the jute fiber by laccase to endow the fiber with hydrophobicity. A hand lay‐up technique was then adopted to prepare jute/epoxy composites. Contact angle and wetting time measurements showed that the surface hydrophobicity of the jute fabric was increased after the enzymatic graft modification. The water absorption and thickness swelling of the DG‐grafted jute fabric/epoxy composite were lower than those of the other composites. The tensile and dynamic mechanical properties of the jute/epoxy composites were enhanced by the surface modification. Scanning electron microscopy images revealed stronger fiber–matrix adhesion in composites with modified fibers. Therefore, the enzymatic graft modification increased the fiber–matrix interface area. The fiber–matrix adhesion was enhanced, and the mechanical properties of the composites were improved. POLYM. COMPOS., 38:1327–1334, 2017. © 2015 Society of Plastics Engineers     

Influence of fiber modification on interfacial adhesion and mechanical properties of pineapple leaf fiber‐epoxy composites

Three kinds of surface treatment, that is, the alkalization (5% w/v NaOH aqueous solution), the deposition of diglycidyl ether of bisphenol A (DGEBA) from toluene solution (1% w/v DGEBA), and the alkalization combined with the deposition of DGEBA (5% w/v NaOH/1% w/v DGEBA) were applied to modify interfacial bonding and to enhance mechanical properties of pineapple leaf fiber (PALF) reinforced epoxy composites. The fiber strength and strain were measured by single fiber test and the fiber strength variation was assessed using Weibull modulus. Furthermore, a fragmentation test was used to quantify the interfacial adhesion of PALF‐epoxy composite. It was verified that the interfacial shear strength of modified PALFs was substantially higher than that of untreated PALF by almost 2–2.7 times because of the greater interaction between the PALFs and epoxy resin matrix. The strongest interfacial adhesion was obtained from the fibers that had been received the alkalization combined with DGEBA deposition. Moreover, the flexural and impact properties of unidirectional PALF‐epoxy composites were greatly enhanced when reinforced with the modified PALFs due to an improvement in interfacial adhesion, particularly in the synergetic use of 5% NaOH and 5% NaOH/1% DGEBA. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Fracture and toughening behavior of aramid fiber/epoxy composites

The effect of short Aramid fibers on the fracture and toughening behavior of epoxy with high glass transition temperature has been studied. Fine dispersion of the fibers throughout the matrix is evidenced by optical microscopy. Compared with neat epoxy resin, the fracture toughness (K_IC) of the composites steadily increases with increasing fiber loading, indicating that addition of Aramid fibers has an effective toughening effect to the intrinsically brittle epoxy matrix. Scanning electron microscopy (SEM) indicates that formation of numerous step structures for fiber‐filled epoxy systems is responsible for the significant toughness improvement. SEM and transmitted optical microscopy show that fiber pullout and fiber breakage are the main toughening mechanisms for the Aramid fiber/epoxy composites. POLYM. COMPOS. 26:333–342, 2005. © 2005 Society of Plastics Engineers.     

Improvement of interfacial adhesion of poly(m‐phenylene isophthalamide) short fiber–thermoplastic elastomer (SEBS) composites by N‐alkylation on fiber surface

A composite of short‐fiber, poly(m‐phenylene isophthalamide), and thermoplastic elastomer styrene (ethylene–butylene) styrene (SEBS), was investigated. The fiber surface was modified by N‐alkylation (heptylation and dodecylation) to improve their compatibility with a less polar SEBS matrix. Observation of fiber‐surface morphology by SEM revealed surface roughness after N‐alkylation. Nearly complete coating of the polymer matrix on the fiber was observed on a fractured surface of the composite, which is evidence for the improvement of fiber–matrix adhesion. It was found that the modulus of the composites grew with increasing fiber loading to approximately the same extent for both unmodified and modified fiber composites. Tensile strength of the modified fiber composites was found to improve significantly over that of the unmodified fiber composite. This suggests that the presence of the alkyl group on the fiber surface is responsible for an improvement of interfacial adhesion. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 2414–2422, 1999     

Interfacial improvement of carbon fiber/epoxy composites using a simple process for depositing commercially functionalized carbon nanotubes on the fibers

An aqueous suspension deposition method was used to coat the sized carbon fibers T700SC and T300B with commercially carboxylic acid-functionalized and hydroxyl-functionalized carbon nanotubes (CNTs). The CNTs on the fiber surfaces were expected to improve the interfacial strength between the fibers and the epoxy. The factors affecting the deposition, especially the fiber sizing, were studied. According to single fiber-composite fragmentation tests, the deposition process results in improved fiber/matrix interfacial adhesion. Using carboxylic acid-functionalized CNTs, the interfacial shear strength was increased 43% for the T700SC composite and 12% for the T300B composite. The relationship between surface functional groups of the CNTs and the interfacial improvement was discussed. The interfacial reinforcing mechanism was explored by analyzing the surface morphology of the carbon fibers, the wettability between the carbon fibers and the epoxy resin, the chemical bonding between the fiber sizing and the CNTs, and fractographic observation of cross-sections of the composites. Results indicate that interfacial friction, chemical bonding and resin toughening are responsible for the interfacial improvement of nanostructured carbon fiber/epoxy composites. The mechanical properties of the CNT-deposited composite laminate were further measured to confirm the effectiveness of this strategy.     

Interfacial evaluation of epoxy/carbon nanofiber nanocomposite reinforced with glycidyl methacrylate treated UHMWPE fiber

Interface interactions of fiber–matrix play a crucial role in final performance of polymer composites. Herein, in situ polymerization of glycidyl methacrylate (GMA) on the ultrahigh molecular weight polyethylene (UHMWPE) fibers surface was proposed for improving the surface activity and adhesion property of UHMWPE fibers towards carbon nanofibers (CNF)‐epoxy nanocomposites. Chemical treatment of UHMWPE fibers was characterized by FTIR, XPS analysis, SEM, and microdroplet tests, confirming that the grafting of poly (GMA) chains on the surface alongside a significant synergy in the interfacial properties. SEM evaluations also exhibited cohesive type of failure for the samples when both GMA‐treated UHMWPE fiber and CNF were used to reinforce epoxy matrix. Compared with unmodified composite, a ～319% increase in interfacial shear strength was observed for the samples reinforced with both 5 wt % GMA‐grafted UHMWPE and 0.5 wt % of CNF. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43751.     

Investigation of mechanical properties of alumina nanoparticle‐loaded hybrid glass/carbon‐fiber‐reinforced epoxy composites

This research work investigates the tensile strength and elastic modulus of the alumina nanoparticles, glass fiber, and carbon fiber reinforced epoxy composites. The first type composites were made by adding 1–5 wt % (in the interval of 1%) of alumina to the epoxy matrix, whereas the second and third categories of composites were made by adding 1–5 wt % short glass, carbon fibers to the matrix. A fourth type of composite has also been synthesized by incorporating both alumina particles (2 wt %) and fibers to the epoxy. Results showed that the longitudinal modulus has significantly improved because of the filler additions. Both tensile strength and modulus are further better for hybrid composites consisting both alumina particles and glass fibers or carbon fibers. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39749.     

Effect of fibers treatment on dynamic mechanical and thermal properties of epoxy hybrid composites

Epoxy hybrid composites fabricated by reinforcing 2‐hydroxy ethyl acrylate (2‐HEA) treated oil palm empty fruit bunch (EFB) and jute fibers. It assume that chemical modification of jute and oil palm EFB fibers increased fiber/matrix interfacial bonding and it results in enhanced thermal properties of hybrid composites. Dynamic mechanical and thermal analysis of treated hybrid composites was carried out. Results indicated that chemical modification of oil palm EFB and jute fibers affect the dynamic mechanical and thermal properties of hybrid composites. The storage modulus values of hybrid composites increases with chemical treatment and loss modulus increased with fiber treatment in hybrid composites. Damping factor peak values of treated hybrid composites shifted toward the lower temperature compared to both untreated hybrid composites. Cole–Cole analysis was made to understand the phase behaviour of the hybrid composites. Thermogravimetric analysis indicated an increased in thermal stability of hybrid composite with the incorporation of chemically modified fibers. POLYM. COMPOS., 36:1669–1674, 2015. © 2014 Society of Plastics Engineers     

Interfacial studies on the surface modified aramid fiber reinforced epoxy composites

In this work, solutions of rare earth modifier (RES) and epoxy chloropropane (ECP) grafting modification method were used for the surface treatment of aramid fiber. The effect of chemical treatment on aramid fiber has been studied in a composite system. The surface characteristics of aramid fibers were characterized by Fourier transform infrared spectroscopy (FTIR). The interfacial properties of aramid/epoxy composites were investigated by means of the single fiber pull‐out tests. The mechanical properties of the aramid/epoxy composites were studied by interlaminar shear strength (ILSS). As a result, it was found that RES surface treatment is superior to ECP grafting treatment in promoting the interfacial adhesion between aramid fiber and epoxy matrix, resulting in the improved mechanical properties of the composites. Meanwhile, the tensile strengths of single fibers were almost not affected by RES treatment. This was probably due to the presence of reactive functional groups on the aramid fiber surface, leading to an increment of interfacial binding force between fibers and matrix in a composite system. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102:4165–4170, 2006     

Incorporation of silicon dioxide nanoparticles at the carbon fiber‐epoxy matrix interphase and its effect on composite mechanical properties

Functionalized silicon dioxide nanoparticles (nano‐fSiO₂) were uniformly deposited on the surface of carbon fibers (CFs) using a coating process which consisted of immersing the fibers directly in a suspension of nano‐fSiO₂ particles and epoxy monomers in 1‐methyl‐2‐pyrrolidinone (NMP). The 0° flexural properties, 90° flexural properties, and Interlaminar shear strength (ILSS) mechanical properties of unidirectional epoxy composites made with nano‐fSiO₂+epoxy sized carbon fibers, with control fibers, and with epoxy‐only sized fibers were measured and compared. An obvious increase of the fiber/matrix adherence strength was obtained with the nano‐fSiO₂+epoxy coating. The nano‐fSiO₂+epoxy sized CF/epoxy composites showed a relative increase of 15%, 50%, and 22% in comparison to control fibers, for the Interlaminar shear strength, the 90^° flexural strength and the 90° flexural modulus, respectively, but little e difference was measured between the different systems for the 0° flexural properties. The observation of the fracture surfaces by scanning electron microscopy of composite fracture confirmed the improvement of the interfacially dependent mechanical properties. POLYM. COMPOS., 38:1474–1482, 2017. © 2015 Society of Plastics Engineers     

Effects of fiber surface chemistry and roughness on interfacial structures of electrospun fiber reinforced epoxy composite films

This work reported the effect of surface chemistry and roughness of electrospun fibers on fiber/matrix interfacial structures and the resultant macroscopical properties of composite films. Three types of fibrous mats composed of ultrafine fibers, that is, cellulose acetate (CANM), polyurethane (PUNM), and cellulose acetate/polyurethane composite (CAPUNM) were fabricated through electrospinning. CA fiber surfaces were rough with many hydroxyl groups; PU fiber surfaces were smooth, whereas CAPU composite fibers exhibited cocontiuous structure with rough surfaces. The fiber‐reinforced epoxy composite films were prepared by the solution impregnation method. The fractured surfaces of the composites were analyzed by scanning electron microscopy. Severe interfacial debonding and fiber pullouts were observed for PUNM/epoxy composites, while strong interfacial adhesion was formed for CANM/epoxy and CAPUNM/epoxy composites. The interfacial structure played important roles in the visible light transmittance of the composite films. For example, CANM/epoxy films showed the best optical property, whereas PUNM/epoxy films displayed the poorest light transmitting property and were translucent. The interfacial structure also affected the mechanical properties of the composites. The mechanical strength of fibrous mats followed an increasing order of CANM < CAPUNM < PUNM, but the mechanical strength of the composite films was in a reverse order, that is, CANM/epoxy > CAPUNM/epoxy > PUNM/epoxy. POLYM. COMPOS., 2011. © 2011 Society of Plastics Engineers     

Mechanical properties of carbon fiber composites modified with nano-SiO2 in the interphase

The performance of carbon fibers-reinforced composites is dependent to a great extent on the properties of fiber–matrix interface. To improve the interfacial properties in carbon fibers/epoxy composites, nano-SiO₂ particles were introduced to the surface of carbon fibers by sizing treatment. Atomic force microscope (AFM) results showed that nano-SiO₂ particles had been introduced on the surface of carbon fibers and increase the surface roughness of carbon fibers. X-ray photoelectron spectroscopy (XPS) showed that nano-SiO₂ particles increased the content of oxygen-containing groups on carbon fibers surface. Single fiber pull-out test (IFSS) and short-beam bending test (ILSS) results showed that the IFSS and ILSS of carbon fibers/epoxy composites could obtain 30.8 and 10.6% improvement compared with the composites without nano-SiO₂, respectively, when the nano-SiO₂ content was 1 wt % in sizing agents. Impact test of carbon fibers/epoxy composites treated by nano-SiO₂ containing sizing showed higher absorption energy than that of carbon fibers/epoxy composites treated by sizing agent without nano-SiO₂. Scanning electron microscopy (SEM) of impact fracture surface showed that the interfacial adhesion between fibers and matrix was improved after nano-SiO₂-modified sizing treatment. Dynamic mechanical thermal analysis (DMTA) showed that the introduction of nano-SiO₂ to carbon fibers surface effectively improved the storage modulus of carbon fibers/epoxy.     

Studies on surface energetics of glass fabrics in an unsaturated polyester matrix system: Effect of sizing treatment on glass fabrics

The surfaces of glass fibers were sized by polyvinyl alcohol (PVA), polyester, and epoxy resin types in order to improve the mechanical interfacial properties of fibers in the unsaturated polyester matrix. The surface energetics of the glass fibers sized were investigated in terms of contact angle measurements using the wicking method based on the Washburn equation, with deionized water and diiodomethane as the wetting liquids. In addition, the mechanical behaviors of the composites were studied in the context of the interlaminar shear strength (ILSS), critical stress intensity factor (K_IC), and flexural measurements. Different evolutions of the London dispersive and specific (or polar) components of the surface free energy of glass fibers were observed after different sizing treatments. The experimental result of the total surface free energies calculated from the sum of their two components showed the highest value in the epoxy‐sized glass fibers. From the measurements of mechanical properties of composites, it was observed that the sizing treatment on fibers could improve the fiber–matrix interfacial adhesion, resulting in improved final mechanical behaviors, a result of the effect of the enhanced total surface free energy of glass fibers in a composite system. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 1439–1445, 2001