Estimation of cutter deflection and form error in ball-end milling processes

This paper presents a method to analyze the 3-dimensional form error of a ball-end milled surface due to the elastic compliance of the cutting tool. In order to estimate the form error in various cutting modes, the cutting force and the cutter deflection models including the effect of the surface inclination were established. The cutting forces were calculated by using the cutter contact area determined from the Z-map of the surface geometry and the current cutter location. The tool deflection responding to the cutting force was then calculated by considering the cutter and the holder stiffness. The cutter was modeled as a cantilever beam consisting of the shank and the flute. The stiffness of the holder was measured experimentally. Various experimental works have been performed to verify the validity of the proposed model. It is shown that the proposed method is capable of accurate prediction of cutting forces and the surface form error.     

Estimation and experimental validation of cutting forces in ball-end milling of sculptured surfaces

Chip thickness calculation has a key important effect on the prediction accuracy of accompanied cutting forces in milling process. This paper presents a mechanistic method for estimating cutting force in ball-end milling of sculptured surfaces for any cases of toolpaths and varying feedrate by incorporation into a new chip thickness model. Based on the given cutter location path and feedrate scheduling strategy, the trace modeling of the cutting edge used to determine the undeformed chip area is resulted from the relative part-tool motion in milling. Issues, such as the selection of the tooth tip and the computation of the preceding cutting path for the tooth tip, are also discussed in detail to ensure the accuracy of chip thickness calculation. Under different chip thicknesses cutting coefficients are regressed with good agreements to calibrated values. Validation tests are carried out on a sculptured surface with curved toolpaths under practical cutting conditions. Comparisons of simulated and experimental results show the effectiveness of the proposed method.     

Cutting force prediction in ball end milling of sculptured surface with Z-level contouring tool path

This paper presents an approach to predict cutting force in 3-axis ball end milling of sculptured surface with Z-level contouring tool path. The variable feed turning angle is proposed to denote the angular position of feed direction within tool axis perpendicular plane. In order to precisely describe the variation of feed turning angle and cutter engagement, the whole process of sculptured surface milling is discretized at intervals of feed per tooth along tool path. Each segmented process is considered as a small steady-state cutting. For each segmented cutting, the feed turning angle is determined according to the position of its start/end points, and the cutter engagement is obtained using a new efficient Z-map method. Both the chip thickness model and cutting force model for steady-state machining are improved for involving the effect of varying feed turning angle and cutter engagement in sculptured surface machining. In validation experiment, a practical 3-axis ball end milling of sculptured surface with Z-level contouring tool path is operated. Comparisons of the predicted cutting forces and the measurements show the reliability of the proposed approach.     

The prediction of dimensional error for sculptured surface productions using the ball-end milling process. Part 1: Chip geometry analysis and cutting force prediction

The study of machining errors caused by tool deflection in the balkend milling process involves four issues, namely the chip geometry, the cutting force, the tool deflection and the deflection sensitivity of the surface geometry. In this paper, chip geometry and cutting force are investigated. The study on chip geometry includes the undeformed radial chip thickness, the chip engagement surface and the relationship between feed boundary and feed angle. For cutting force prediction, a rigid force model and a flexible force model are developed. Instantaneous cutting forces of a machining experiment for two 2D sculptured surfaces produced by the ball-end milling process are simulated using these force models and are verified by force measurements. This information is used in Part 2 of this paper, together with a tool deflection model and the deflection sensitivity of the surface geometry, to predict the machining errors of the machined sculptured surfaces.     

The prediction of cutting force in ball-end milling

Due to the development of CNC machining centers and automatic programming software, the ball-end milling have become the most widely used machining process for sculptured surfaces. In this study, the ball-end milling process has been analysed, and its cutting force model has been developed to predict the instantaneous cutting force on given machining conditions. The development of the model is based on the analysis of cutting geometry of the ball-end mill with plane rake faces. A cutting edge of the ball-end mill was considered as a series of infinitesimal elements, and the geometry of a cutting edge element was analysed to calculate the necessary parameters for its oblique cutting process assuming that each cutting edge was straight. The oblique cutting process in the small cutting edge element has been analysed as an orthogonal cutting process in the plane containing the cutting velocity and chip flow vectors. And with the orthogonal cutting data obtained from end turning tests on thin-walled tubes over wide range of cutting and tooling conditions, the cutting forces of ball-end milling could be predicted using the model. The predicted cutting forces have shown a fairly good agreement with test results in various machining modes.     

Static rigid force model for 3-axis ball-end milling of sculptured surfaces

Static rigid force model is used to estimate cutting forces of sculptured surface in a straightforward way, without considering tool deflection, machine tool dynamic behavior and any vibration effects. Two programs were used for calculations, “ACIS” the 3-D geometric modeler and “VISUAL BASIC”. Two programs were edited and used to perform the calculations, the scheme program to model the work piece, tool and cutting edge and to obtain the geometric data and the VISUAL BASIC program design to use ACIS geometric data to calculate the cutting forces. The engaged part of the cutting edge and work piece is divided into small differential oblique cutting edge segments. Friction, shear angles and shear stresses are identified from orthogonal cutting database available in literature. The cutting force components, for each tool rotational position, are calculated by summing up the differential cutting forces. Laboratory tests were conducted to verify the predictions of the model. The work pieces were prepared from CK45 steel using an insert-type ball-end cutter. No coolant was used in any of the experimental works. The cutting forces predicted have shown good agreement with experimental results.     

The estimation of cutting forces and specific force coefficients during finishing ball end milling of inclined surfaces

The majority of cutting force models applied for the ball end milling process includes only the influence of cutting parameters (e.g. feedrate, depth of cut, cutting speed) and estimates forces on the basis of coefficients calibrated during slot milling. Furthermore, the radial run out phenomenon is predominantly not considered in these models. However this approach can induce excessive force estimation errors, especially during finishing ball end milling of sculptured surfaces. In addition, most of cutting force models is formulated for the ball end milling process with axial depths of cut exceeding 0.5 mm and thus, they are not oriented directly to the finishing processes. Therefore, this paper proposes an accurate cutting force model applied for the finishing ball end milling, which includes also the influence of surface inclination and cutter's run out. As part of this work the new method of specific force coefficients calibration has been also developed. This approach is based on the calibration during ball end milling with various surface inclinations and the application of instantaneous force signals as an input data. Furthermore, the analysis of specific force coefficients in function of feed per tooth, cutting speed and surface inclination angle was also presented. In order to determine geometrical elements of cut precisely, the radial run out was considered in equations applied for the calculation of sectional area of cut and active length of cutting edge. Research revealed that cutter's run out and surface inclination angle have significant influence on the cutting forces, both in the quantitative and qualitative aspect. The formulated model enables cutting force estimation in the wide range of cutting parameters, assuring relative error's values below 16%. Furthermore, the consideration of cutter's radial run out phenomenon in the developed model enables the reduction of model's relative error by the 7% in relation to the model excluding radial run out.     

Phase width analysis of cutting forces considering bottom edge cutting and cutter runout calibration in flat end milling of titanium alloy

This paper is concerned with the combined cutting effects of both flank and bottom edges based on a systematic study of the cutting force in flat end milling of the titanium alloy. Besides the flank edge, the bottom edge of the cutter is also found to be an important factor influencing the cutting force distributions and can lead to uniform phase widths for non-zero cutting forces even under considerable cutter runout. One such phenomenon of uniform phase width induced by the bottom edge for the cutting force is deeply revealed. To do this, the models for characterizing the cutting force coefficients related to both edges are established based on the measured instantaneous cutting forces, and cutter runout is considered in the computation of process geometry parameters such as cutter/workpiece engagements and instantaneous uncut chip geometry parameters. Novel algorithms for identifying the cutter runout parameters and the bottom uncut chip width are also developed. Results definitely show that the flank cutting force coefficients can be treated as constants and that size effect obviously exists in the bottom cutting force coefficients that can be characterized by a power function of the bottom uncut chip width.The proposed model is validated through a comparative study with the existing model and experiments. From the outcomes of the current work, it is clearly seen that the prediction of cutting forces for titanium alloy can resort to the proposed model instead of traditional ones.     

Effect of chamfer angle on wear of PCBN cutting tool

In precision hard turning, a remaining problem is to minimise tool wear to maintain the accuracy of geometry and surface finish. Tool wear not only directly reduces the part geometry accuracy but also increases cutting forces drastically. The change in the cutting forces also causes instability in the tool motion, which results in more inaccuracy. PCBN cutting tools are often used in hard turning. However, they are still relatively expensive compared to ordinary carbide cutting tools. In order to attain sufficiently high production rates at minimum cost, increase of knowledge on cutting tool geometry is necessary. This article presents a study of the effect of chamfer angle on tool wear of PCBN cutting tool in the super finishing hard turning. The correlation between cutting force, tool wear and tool life were investigated. The optimised chamfer angle for PCBN cutting tool is suggested. Finally, the distribution of stresses and maximum principal stress working on the tool edge were calculated with the use of finite element method.     

The prediction of dimensional error for sculptured surface productions using the ball-end milling process. Part 2: Surface generation model and experimental verification

This paper presents a surface generation model for sculptured surface productions using the ball-end milling process. In this model, machining errors caused by tool deflections are studied. As shown in Part 1 of this paper, instantaneous horizontal cutting forces can be evaluated from the cutting geometries using mechanistic force models. In this paper, a tool deflection model is developed to calculate the corresponding horizontal tool deflection at the surface generation points on the cutter. The sensitivity of the machining errors to tool deflections, both in magnitude and direction, has been analyzed via the deflection sensitivity of the surface geometry. Machining errors are then determined from the tool deflection and the deflection sensitivity of the designed surface. The ability of this model in predicting dimensional errors for sculptured surfaces produced by the ball-end milling process has been verified by a machining experiment. In addition to providing a means to predict dimensional accuracy prior to actual cutting, this surface generation model can also be used as a tool for quality control and machining planning.     

Milling force prediction using a dynamic shear length model

Modelling of cutting forces in milling is often needed in machining automation. In this paper, a new method for the determination of the cutting forces in face milling is presented, which applies a predictive machining theory originally developed for orthogonal cutting to milling operations, with a dynamic shear length model developed and incorporated. The proposed dynamic shear length model is developed based on the analysis for the true tooth trajectories of a milling cutter, taking into account of the characteristic wavy surface effects in milling. The prediction for the cutting forces is carried out at each step of the angular increment of cutter rotation from input data of fundamental workpiece material properties, tool geometry and cutting conditions. Cutting forces at a cutter tooth can be predicted once the shear angle, shear length, shear plane area, and the shear flow stress along the shear length have been determined. The milling force prediction using the dynamic shear length model is verified through milling experimental tests. The sensitivity of the difference between the static and dynamic shear length models with respect to the feed per tooth and the cutter diameter is discussed.     

The prediction of cutting forces in the ball-end milling process—II. Cut geometry analysis and model verification

This paper presents a model for the prediction of cutting forces in the ball-end milling process. The steps used in developing the force model are based on the mechanistic principles of metal cutting. The cutting forces are calculated on the basis of the engaged cut geometry, the underformed chip thickness distribution along the cutting edges, and the empirical relationships that relate the cutting forces to the undeformed chip geometry. A simplified cutter runout model, which characterizes the effect of cutter axis offset and tilt on the undeformed chip geometry, has been formulated. A model building procedure based on experimentally measured average forces and the associated runout data is developed to identify the numerical values of the empirical model parameters for the particular workpiece/cutter combination.     

Numerical simulation and prediction of cutting forces in five-axis milling processes with cutter run-out

Radial cutter runout is a common issue in milling processes and has a direct effect on milling stability due to variations of resulting chip load and forces. This paper presents a new method to effectively model and predict the instantaneous cutting forces in 5-axis milling processes with radial cutter runout based on tool motion analysis. First, the undeformed chip thickness model taking runout effect into account is established under continuous change of cutter axis orientation by means of the sweep traces of cutter edges. Second, the engaged cutting edge is determined and cutting coefficients are subsequently calibrated. Finally, the method of identifying runout parameters from the measured cutting forces is proposed, and mechanistic method is then applied to predict the cutting force. Since this method is completely based on the relative motion analysis of tool-part, it can reduce the prediction errors of cutting forces effectively and is suitable for generic rotation cutters. Several validation examples are given under different cutting conditions to prove its effectiveness and accuracy. The results reveal that the developed method can predict the cutter forces with a high accuracy and has the ability to be used in simulations and optimizations of five-axis machining.     

Dynamic response analysis in end milling using pre-twisted beam finite elements

This paper develops an analytical model for estimating the dynamic responses in end milling, i.e. dynamic milling cutter deflections and cutting forces, by using the finite-element method along with an adequate end milling-cutting force model. The whole cutting system includes the spindle, the bearings and the cutter. The spindle is modelled structurally with the Timoshenko-beam element, the milling cutter with the pre-twisted Timoshenko-beam element due to its special geometry, and the bearings with lumped springs and dampers. Because the damping matrix in the resulting finite-element equation of motion for the whole cutting system is not one of proportional damping due to the presence of bearing damping, the state-vector approach and the convolution integral is used to find the solution of the equation of motion. To assure the accuracy of prediction of the dynamic response, the associated cutting force model should be sufficiently precise. Since the dynamic cutting force is proportional to the chip thickness, a quite accurate alogorithm for the calculation of the variation of the chip thickness due to geometry, run-out and spindle-tool viration is developed. A number of dynamic cutting forces and tool deflections obtained from the present model for various cutting conditions are compared with the experimental and analytical results available in the literature, good agreement being demonstrated for these comparisons. The present model is useful, therefore, for the prediction of end milling instability. Also, the tool deflections obtained using the pre-twisted beam element are found to be smaller than those obtained using the straight beam element without pre-twist angle. Hence neglecting the pre-twist angle in the structural model of the milling cutter may overestimate the tool deflections.     

A new thermomechanical model of cutting applied to turning operations. Part I. Theory

In this paper, an analytical approach is used to model the thermomechanical process of chip formation in a turning operation. In order to study the effects of the cutting edge geometry, it is important to analyse its global and local effects such as the chip flow direction, the cutting forces and the temperature distribution at the rake face. To take into account the real cutting edge geometry, the engaged part in cutting of the rounded nose is decomposed into a set of cutting edge elements. Thus each elementary chip produced by a straight cutting edge element, is obtained from an oblique cutting process. The fact that the local chip flow is imposed by the global chip movement is accounted for by considering appropriate interactions between adjacent chip elements. Consequently, a modified version of the oblique cutting model of Moufki et al. [Int. J. Mech. Sci. 42 (2000) 1205; Int. J. Mach. Tools Manufact. 44 (9) (2004) 971] is developed and applied to each cutting edge element in order to obtain the cutting forces and the temperature distributions along the rake face. The material characteristics such as strain rate sensitivity, strain hardening and thermal softening, the thermomechanical coupling and the inertia effects are taken into account in the modelling. The model can be used to predict the cutting forces, the global chip flow direction, the surface contact between chip and tool and the temperature distribution at the rake face which affects strongly the tool wear. Part II of this work consists in a parametric study where the effects of cutting conditions, cutting edge geometry, and friction at the tool–chip interface are investigated. The tendencies predicted by the model are also compared qualitatively with the experimental trends founded in the literature.     

Mechanics and dynamics of general milling cutters.: Part I: helical end mills

A variety of helical end mill geometry is used in the industry. Helical cylindrical, helical ball, taper helical ball, bull nosed and special purpose end mills are widely used in aerospace, automotive and die machining industry. While the geometry of each cutter may be different, the mechanics and dynamics of the milling process at each cutting edge point are common. This paper presents a generalized mathematical model of most helical end mills used in the industry. The end mill geometry is modeled by helical flutes wrapped around a parametric envelope. The coordinates of a cutting edge point along the parametric helical flute are mathematically expressed. The chip thickness at each cutting point is evaluated by using the true kinematics of milling including the structural vibrations of both cutter and workpiece. By integrating the process along each cutting edge, which is in contact with the workpiece, the cutting forces, vibrations, dimensional surface finish and chatter stability lobes for an arbitrary end mill can be predicted. The predicted and measured cutting forces, surface roughness and stability lobes for ball, helical tapered ball, and bull nosed end mills are provided to illustrate the viability of the proposed generalized end mill analysis.     

Effect of cutter runout on process geometry and forces in peripheral milling of curved surfaces with variable curvature

This paper presents a novel method for cutting force modeling related to peripheral milling of curved surfaces including the effect of cutter runout, which often changes the rotation radii of cutting points. Emphasis is put on how to efficiently incorporate the continuously changing workpiece geometry along the tool path into the calculation procedure of tool position, feed direction, instantaneous uncut chip thickness (IUCT) and entry/exit angles, which are required in the calculation of cutting force. Mathematical models are derived in detail to calculate these process parameters in occurrence of cutter runout. On the basis of developed models, some key techniques related to the prediction of the instantaneous cutting forces in peripheral milling of curved surfaces are suggested together with a whole simulation procedure. Experiments are performed to verify the predicted cutting forces; meanwhile, the efficiency of the proposed method is highlighted by a comparative study of the existing method taken from the literature.     

A chatter free calibration method for determining cutter runout and cutting force coefficients in ball-end milling

The accuracy of cutting force coefficients plays an important role in predicting reliable cutting force, stability lobes as well as surface location error in ball-end milling. In order to avoid chatter risk of the traditional calibration test with an entire-ball-immersed cutting depth, a cylindrical surface milling method is proposed to calibrate the cutting force coefficients with the characteristics of low cutting depth and varying lead angle. A dual-cubic-polynomial function is also presented to describe the non-uniform cutting force coefficients of the ball part cutting edge and the nonlinear chip size effect on cutting force. The variation of the maximum chip thickness versus the lead angle is established with the consideration of cutter runout. According to the dependence of chip thickness on lead angle, a runout identification method is introduced by seeking the critical lead angle at which one of the cutter flutes is just thoroughly out of cut. Then, a lumped equivalent method is adopted for the low cutting depth condition so that the dual-cubic-polynomial model can be calibrated for the chip size effect and the cutting force coefficients respectively. The accuracy of the proposed calibration method has been validated experimentally with a series of milling tests. The stability examinations indicate that the proposed method has an evident chatter-free advantage, compared with that of varying cutting depth method.     

Enhanced virtual machining for sculptured surfaces by integrating machine tool error models into NC machining simulation

Sculptured surface machining is a time-consuming and costly process. It requires simultaneously controlled motion of the machine axes. However, positioning inaccuracies or errors exist in machine tools. The combination of error motions of the machine axes will result in a complicated pattern of part geometry errors. In order to quantitatively predict these part geometry errors, a new application framework ‘enhanced virtual machining’ is developed. It integrates machine tool error models into NC machining simulation. The ideal cutter path in the NC program for surface machining is discretized into sub-paths. For each interpolated cutter location, the machine geometric errors are predicted from the machine tool error model. Both the solid modeling approach and the surface modeling approach are used to translate machine geometric errors into part geometry errors for sculptured surface machining. The solid modeling approach obtains the final part geometry by subtracting the tool swept volume from the stock geometric model. The surface modeling approach approximates the actual cutter contact points by calculating the cutting tool motion and geometry. The simulation results show that the machine tool error model can be effectively integrated into sculptured surface machining to predict part geometry errors before the real cutting begins.     

Prediction of ball-end milling forces from orthogonal cutting data

The mechanics of cutting with helical ball-end mills are presented. The fundamental cutting parameters, the yield shear stress, average friction coefficient on the rake face and shear angle are measured from a set of orthogonal cutting tests at various cutting speeds and feeds. The cutting forces are separated into edge or ploughing forces and shearing forces. The helical flutes are divided into small differential oblique cutting edge segments. The orthogonal cutting parameters are carried to oblique milling edge geometry using the classical oblique transformation method, where the chip flow angle is assumed to be equal to the local helix angle. The cutting force distribution on the helical ball-end mill flutes is accurately predicted by the proposed method, and the model is validated experimentally and statistically by conducting more than 60 ball-end milling experiments.