A 0.5-V 8-bit 10-Ms/s Pipelined ADC in 90-nm CMOS

This paper presents a pipelined analog-to-digital converter (ADC) operating from a 0.5-V supply voltage. The ADC uses true low-voltage design techniques that do not require any on-chip supply or clock voltage boosting. The switch OFF leakage in the sampling circuit is suppressed using a cascaded sampling technique. A front-end signal-path sample-and-hold amplifier (SHA) is avoided by using a coarse auxiliary sample and hold (S/H) for the sub-ADC and by synchronizing the sub-ADC and pipeline-stage sampling circuit. A 0.5-V operational transconductance amplifier (OTA) is presented that provides inter-stage amplification with an 8-bit performance for the pipelined ADC operating at 10 Ms/s. The chip was fabricated on a standard 90 nm CMOS technology and measures 1.2 mm times 1.2 mm. The prototype chip has eight identical stages and stage scaling was not used. It consumes 2.4 mW for 10-Ms/s operation. Measured peak SNDR is 48.1 dB and peak SFDR is 57.2 dB for a full-scale sinusoidal input. Maximal integral nonlinearity and differential nonlinearity are 1.19 and 0.55 LSB, respectively.     

A 6-bit 800-MS/s Pipelined A/D Converter With Open-Loop Amplifiers

A 6-bit 800-MS/s pipelined A/D converter (ADC) achieves SNDR and SFDR of 33.7 dB and 47.5 dB, respectively. Employing voltage-mode open-loop amplifiers in gain stages, global gain control techniques, and two-bank-interleaved architecture, the proposed pipelined A/D converter relaxes stringent design tradeoffs between speed and power. Fabricated in a 0.18-mum CMOS technology, the ADC consumes 105 mW from a 1.8-V power supply while the active area is only 0.5 mm²     

A 13-b 10-Msample/s ADC digitally calibrated with oversamplingdelta-sigma converter

Two key techniques necessary to digitally calibrate multistep or pipelined converters are demonstrated in a differential 5-V, 13-b, 10-Msample/s analog-to-digital converter (ADC). One technique, called code-error calibration, is to linearize the transfer characteristic of digital-to-analog converters (DAC's) while the other, called gain-error proration, is to evenly distribute interstage gain errors over the full conversion range. The core of the former technique is an oversampling delta-sigma ratio calibrator working synchronously with the converter. This digital calibration process constantly tracks and updates the code errors without interfering with the normal operation. The prototype converter fabricated using a 1.4-μm BiCMOS process consumes 360 mW with a 5-V single supply and exhibits a signal-to-noise ratio of 71 dB and a maximum end-point integral nonlinearity of 1.8 LSB at a 13-b level. The proposed techniques can be incorporated into general multistep or pipelined ADC's without sacrificing the conversion speed     

A low power 12-b 40-MS/s pipeline ADC

This paper describes a 12-bit, 40-MS/s pipelined A/D converter (ADC) which is implemented in 0.18-μm CMOS process drawing 76-mW power from 3.3-V supply. Multi-bit architectures as well as telescopic operational transconductance amplifiers (OTAs) are adopted in all pipeline stages for good power efficiency. In the first two stages,particularly, 3-bit/stage architectures are used to improve the ADC's linearity performance. The ADC is calibration-free and achieves a DNL of less than 0.51 LSB and an INL of less than 1 LSB. The SNDR performance is above 67 dB below Nyquist. The 80-dB SFDR performance is maintained within 1 dB for input frequencies up to 49 MHz at full sampling rate.     

A power-efficient 10-bit 40-MS/s sub-sampling pipelined CMOS analog-to-digital converter

This paper presents a 10-bit 40-MS/s pipelined analog-to-digital converter (ADC) in a 0.13-μm CMOS process for subsampling applications. A simplified opamp-sharing scheme between two successive pipelined stages is proposed to reduce the power consumption. For subsampling, a cost-effective fast input-tracking switch with high linearity is introduced to sample the input signal up to 75 MHz. A two-stage amplifier with hybrid frequency compensation is developed to achieve both high bandwidth and large swing with low power dissipation. The measured result shows that the ADC achieves over 77 dB spurious free dynamic range (SFDR) and 57.3 dB signal-to-noise-plus-distortion ratio (SNDR) within the first Nyquist zone and maintains over 70 dB SFDR and 55.3 dB SNDR for input signal up to 75 MHz. The peak differential nonlinearity (DNL) and integral nonlinearity (INL) are ±0.2 LSB and ±0.3 LSB, respectively. The ADC consumes 15.6 mW at the sampling rate of 40 MHz from a 1.2-V supply voltage, and achieves a figure-of-merit (FOM) value of 0.22 pJ per conversion step.     

A 10-bit 50-MS/s subsampling pipelined ADC based on SMDAC and opamp sharing

This paper describes a 10-bit,50-MS/s pipelined A/D converter(ADC) with proposed area- and power-efficient architecture.The conventional dedicated sample-hold-amplifier(SHA) is eliminated and the matching requirement between the first multiplying digital-to-analog converter(MDAC) and sub-ADC is also avoided by using the SHA merged with the first MDAC(SMDAC) architecture,which features low power and stabilization.Further reduction of power and area is achieved by sharing an opamp between two successive pi...     

Digital background calibration of charge pump based pipelined ADC

In the presented work, digital background calibration of a charge pump based pipelined ADC is presented. A 10-bit 100 MS/s pipelined ADC is designed using TSMC 0.18 µm CMOS technology operating on a 1.8 V power supply voltage. A power efficient opamp-less charge pump based technique is chosen to achieve the desired stage voltage gain of 2 and digital background calibration is used to calibrate the inter-stage gain error. After calibration, the ADC achieves an SNDR of 66.78 dB and SFDR of 79.3 dB. Also, DNL improves to +0.6/–0.4 LSB and INL improves from +9.3/–9.6 LSB to within ±0.5 LSB, consuming 16.53 mW of power.     

A 10-b 120-Msample/s time-interleaved analog-to-digital converter with digital background calibration

Digital calibration using adaptive signal processing corrects for offset mismatch, gain mismatch, and sample-time error between time-interleaved channels in a 10-b 120-Msample/s pipelined analog-to-digital converter (ADC). Offset mismatch between channels is overcome with a random chopper-based offset calibration. Gain mismatch and sample-time error are overcome with correlation-based algorithms, which drive the correlation between a signal and its chopped image or its chopped and delayed image to zero. Test results show that, with a 0.99-MHz sinusoidal input, the ADC achieves a peak signal-to-noise-and-distortion ratio (SNDR) of 56.8 dB, a peak integral nonlinearity of 0.88 least significant bit (LSB), and a peak differential nonlinearity of 0.44 LSB. For a 39.9-MHz sinusoidal input, the ADC achieves a peak SNDR of 50.2 dB. The active area is 5.2 mm/sup 2/, and the power dissipation is 234 mW from a 3.3-V supply.     

An 8-bit 200-MSample/s Pipelined ADC With Mixed-Mode Front-End S/H Circuit

This paper describes an 8-bit pipelined analog-to-digital converter (ADC) using a mixed-mode sample-and-hold (S/H) circuit at the front-end. The mixed-mode sampling technique reduces signal swings in pipelined ADCs while maintaining the signal-to-noise ratio. The reduction of signal swings relaxes the operational amplifier (opamp) gain, slew rate, bandwidth, and capacitor-matching requirements in pipelined ADCs. Due to the mixed-mode S/H technique, the single-stage opamps and small capacitor sizes can be used in this pipelined ADC, leading to a high speed and low-power consumption. Fabricated in a 0.18- $mu{hbox {m}}$ CMOS process, the 8-bit pipelined ADC consumes 22 mW with 1.8-V supply voltage. When sampling at 200 MSample/s, the prototype ADC achieves 54-dB spurious free dynamic range and 45-dB signal-to-noise and distortion ratio. The measured integral nonlinearity and differential nonlinearity are 0.34 LSB and 0.3 LSB, respectively.      

A 1.2-V 19.2-mW 10-bit 30-MS/s pipelined ADC in 0.13-icm CMOS

A 10-bit 30-MS/s pipelined analog-to-digital converter (ADC) is presented.For the sake of lower power and area,the pipelined stages are scaled in current and area,and op amps are shared between the successive stages.The ADC is realized in the 0.13-tt,m 1-poly 8-copper mixed signal CMOS process operating at 1.2-V supply voltage.Design approaches are discussed to overcome the challenges associated with this choice of process and supply voltage,such as limited dynamic range,poor analog characteristic devices,the limited linearity of analog switches and the embedded sub-1-V bandgap voltage reference.Measured results show that the ADC achieves 55.1-dB signal-to-noise and distortion ratio,67.5-dB spurious free dynamic range and 19.2-mW power under conditions of 30 MSPS and 10.7-MHz input signal.The FoM is 0.33 pJ/step.The peak integral and differential nonlinearities are 1.13 LSB and 0.77 LSB,respectively.The ADC core area is 0.94 mm2.     

A 2.5-V 10-b 120-MSample/s CMOS pipelined ADC based on merged-capacitor switching

This work describes a 10-b multibit-per-stage pipelined CMOS analog-to-digital converter (ADC) incorporating the merged-capacitor switching (MCS) technique. The proposed MCS technique improves the signal processing speed and resolution of the ADC by reducing the required number of unit capacitors by half in comparison to a conventional ADC. The ADC resolution based on the proposed MCS technique can be extended further by employing a commutated feedback-capacitor switching (CFCS) technique. The prototype ADC achieves better than 53-dB signal-to-noise-and-distortion ratio (SNDR) at 120 MSample/s and 54-dB SNDR and 68-dB spurious-free dynamic range (SFDR) for input frequencies up to Nyquist at 100 MSample/s. The measured differential and integral nonlinearities of the prototype are within /spl plusmn/0.40 LSB and /spl plusmn/0.48 LSB, respectively. The ADC fabricated in a 0.25-/spl mu/m CMOS occupies 3.6 mm/sup 2/ of active die area and consumes 208 mW under a 2.5-V power supply.     

55-mW 200-MSPS 10-bit pipeline ADCs for wireless receivers

A new power reduction technique for analog-to-digital converters (ADCs) is proposed in this paper. The power reduction technique is a kind of amplifier sharing technique and it is suitable for ADCs in a wireless receiver. A test chip, which contains two ADCs, is fabricated in 90-nm 1-poly 7-metal CMOS technology. The 10-bit ADC dissipates 55 mW from 1.2-V supply, when the ADC operates at 200 mega-samples per second (MSPS). The 10-bit, 200-MSPS ADCs achieve maximum differential nonlinearity (DNL) of 0.66 least significant bit (LSB), maximum integral nonlinearity (INL) of 1.00 LSB, a spurious-free dynamic range (SFDR) of 66.5 dB and a peak signal-to-noise plus distortion ratio (SNDR) of 54.4 dB that corresponds to 8.7 effective number of bits (ENOB). The active area is 1.8 mm /spl times/ 1.4 mm.     

Current mode ADC design in a 0.5-μm CMOS process

This paper presents a pipelined current mode analog to digital converter (ADC) designed in a 0.5-μm CMOS process. Adopting the global and local bias scheme, the number of interconnect signal lines is reduced numerously, and the ADC exhibits the advantages of scalability and portability. Without using linear capacitance,this ADC can be implemented in a standard digital CMOS process; thus, it is suitable for applications in the system on one chip (SoC) design as an analogue IP. Simulations show that the proposed current mode ADC can operate in a wide supply range from 3 to 7 V and a wide quantization range from ±64 to ±256μA. Adopting the histogram testing method, the ADC was tested in a 3.3 V supply voltage/±64μA quantization range and a 5 V supply voltage/±256μA quantization range, respectively. The results reveal that this ADC achieves a spurious free dynamic range of 61.46dB, DNL/INL are -0.005 to +0.027 LSB/-0.1 to +0.2 LSB, respectively, under a 5 V supply voltage with a digital error correction technique.     

A digitally self-calibrating 14-bit 10-MHz CMOS pipelined A/Dconverter

A digitally self-calibrating pipelined analog-to-digital converter (ADC) featuring 1.5-bit/stage structure is presented. The integral (INL) and differential nonlinearity (DNL) errors are removed using a novel digital calibration algorithm, which also eliminates missing codes that can occur with other calibration algorithms near the extremes of the input range. After calibration, the measured DNL is ±0.6 LSB and the INL is ±2.5 LSB at the 14-bit level. Sampling at a 10-MHz rate, the chip dissipates 220 mW and (post-calibration) yields a signal-to-noise ratio of 77 dB and a spurious-free dynamic range of 95 dB with 4.8-MHz sine wave input signal. The chip is fabricated in 0.5-μm CMOS double-poly double-metal process, measures 3.8 mm × 3.3 mm (150 mil × 130 mil), and operates from a single 5-V supply     

A 1.8-V 67-mW 10-bit 100-MS/s pipelined ADC using time-shifted CDS technique

A time-shifted correlated double sampling (CDS) technique is proposed in the design of a 10-bit 100-MS/s pipelined ADC. This technique significantly reduces the finite opamp gain error without compromising the conversion speed, allowing the active opamp blocks to be replaced by simple cascoded CMOS inverters. Both high-speed and low-power operation is achieved without compromising the accuracy requirement. An efficient common-mode voltage control is introduced for pseudodifferential architecture which can further reduce power consumption. Fabricated in a 0.18-/spl mu/m CMOS process, the prototype 10-bit pipelined ADC occupies 2.5 mm/sup 2/ of active die area. With 1-MHz input signal, it achieves 65-dB SFDR and 54-dB SNDR at 100MS/s. For 99-MHz input signal, the SFDR and SNDR are 63 and 51 dB, respectively. The total power consumption is 67 mW at 1.8-V supply, of which analog portion consumes 45 mW without any opamp current scaling down the pipeline.     

A 12-bit 20-Msample/s pipelined analog-to-digital converter with nested digital background calibration

A 12-bit 20-Msample/s pipelined analog-to-digital converter (ADC) is calibrated in the background using an algorithmic ADC, which is itself calibrated in the foreground. The overall calibration architecture is nested. The calibration overcomes the circuit nonidealities caused by capacitor mismatch and finite operational amplifier (opamp) gain both in the pipelined ADC and the algorithmic ADC. With a 58-kHz sinusoidal input, test results show that the pipelined ADC achieves a peak signal-to-noise-and-distortion ratio (SNDR) of 70.8 dB, a peak spurious-free dynamic range (SFDR) of 93.3 dB, a total harmonic distortion (THD) of -92.9 dB, and a peak integral nonlinearity (INL) of 0.47 least significant bit (LSB). The total power dissipation is 254 mW from 3.3 V. The active area is 7.5 mm/sup 2/ in 0.35-/spl mu/m CMOS.     

A 4.8 GS/s 5-bit ADC-Based Receiver With Embedded DFE for Signal Equalization

A 5-bit 4.8 GS/s 4-way time-interleaved ADC is designed for a receiver front-end in a 0.13 $muhbox{m}$ CMOS technology. Each time-interleaved ADC uses look-ahead pipelined stages to enable higher sample rates and more linear residue characteristics than a conventional pipeline ADC. At 1.2 GHz per path, the residue amplifiers settle to 75% of their final value, however, the linear residue characteristics allows using digital reference calibration to enable 30.4 dB of SNDR with a 1.2 MHz input signal. A capacitor pre-charging technique reduces the memory effect errors of the incompletely settled residue to 2% of the stage output swing. The peak INL and DNL are measured as 0.65LSB and 0.55LSB, respectively. The measured ERBW is ${sim},$ 6.1 GHz. The ADC, including the reference buffers, consumes 300 mW from a 1.2-V supply while operating at 4.8 GHz conversion rate. A stage-by-stage feedback compensates the possible bandwidth limitation of the system using a per-stage speculative DFE. The DFE tap is adjustable between 0 and 0.4 using 8 control bits.      

A CMOS switch-capacitor 14-bit 100 Msps pipeline ADC with over 90 dB SFDR

This article presents a design of 14-bit 100?Msamples/s pipelined analog-to-digital converter (ADC) implemented in 0.18?µm CMOS. A charge-sharing correction (CSC) is proposed to remove the input-dependent charge-injection, along with a floating-well bulk-driven technique, a fast-settling reference generator and a low-jitter clock circuit, guaranteeing the high dynamic performance of the ADC. A scheme of background calibration minimises the error due to the capacitor mismatch and opamp non-ideality, ensuring the overall linearity. The measured results show that the prototype ADC achieves spurious-free dynamic range (SFDR) of 91?dB, signal-to-noise-and-distortion ratio (SNDR) of 73.1?dB, differential nonlinearity (DNL) of +0.61/?0.57?LSB and integrated nonlinearity (INL) of +1.1/?1.0?LSB at 30?MHz input and maintains over 78?dB SFDR and 65?dB SNDR up to 425?MHz, consuming 223?mW totally.     

基于码密度统计的流水线模数转换器校准算法研究

本文提出了一种用于校准流水线模数转换器线性误差的数字后台校准算法。该算法不需要修改转换器级电路部分,只需要一部分用于统计模数转换器输出码的数字电路即可完成。通过分析流水线模数转换器输出的数字码,该算法可以计算出每一级级电路对应的权重。本文利用一个14位的流水线模数转换器来验证该算法。测试结果显示,转换器的积分非线性由90LSB下降到0.8LSB,微分非线性由2LSB下降到0.3LSB;信噪失真比从38dB提高到66.5dB,总谐波失真从-37dB下降到-80dB。转换器的线性度有很大提高。     

A systematic design approach for low-power 10-bit 100 MS/s pipelined ADC

A systematic design approach for low-power 10-bit, 100 MS/s pipelined analog-to-digital converter (ADC) is presented. At architectural level various per-stage-resolution are analyzed and most suitable architecture is selected for designing 10-bit, 100 MS/s pipeline ADC. At Circuit level a modified wide-bandwidth and high-gain two-stage operational transconductance amplifier (OTA) proposed in this work is used in track-and-hold amplifier (THA) and multiplying digital-to-analog converter (MDAC) sections, to reduce power consumption and thermal noise contribution by the ADC. The signal swing of the analog functional blocks (THA and MDAC sections) is allowed to exceed the supply voltage (1.8 V), which further increases the dynamic range of the circuit. Charge-sharing comparator is proposed in this work, which reduces the dynamic power dissipation and kickback noise of the comparator circuit. The bootstrap technique and bottom plate sampling technique is employed in THA and MDAC sections to reduce the nonlinearity error associated with the input signal resulting in a signal-to-noise-distortion ratio of 58.72/57.57 dB at 2 MHz/Nyquist frequency, respectively. The maximum differential nonlinearity (DNL) is +0.6167/−0.3151 LSB and the maximum integral nonlinearity (INL) is +0.4271/−0.4712 LSB. The dynamic range of the ADC is 58.72 dB for full-scale input signal at 2 MHz input frequency. The ADC consumes 52.6 mW at 100 MS/s sampling rate. The circuit is implemented using UMC-180 nm digital CMOS technology.