Performance measurements from LYSO scintillators coupled to a CMOS position sensitive SSPM detector

We have designed a 5×5 mm² position sensitive solid-state photomultiplier (PS-SSPM) using a complementary metal-oxide-semiconductor (CMOS) process that provides imaging capability on the micro-pixel level. The PS-SSPM has 11,664 micro-pixels total, with each having an active area and micro-pixel pitch of 30×30 μm² and 44.3 μm, respectively. The PS-SSPM was then examined for its performance characteristics such as its energy and spatial resolution, and LYSO scintillator array imaging capabilities. When coupled to 5×5×3 mm³ LYSO, the energy resolution at 511 keV (²²Na) was measured as a function of bias, and corrected for the PS-SSPM non-linear output. The resolution is 14% (FWHM) at 511 keV with 30 V bias. The LYSO coincidence timing resolution was 9.4 ns (FWHM) at 511 keV. Spatial resolution studies were conducted using a focused (∼30 μm beam spot diameter) pulsed 635 nm diode laser. Scintillator array imaging studies were conducted at 511 keV using a 6×6 LYSO array, having 500 μm pixels (530 μm pitch) and 5 mm tall.     

Basic study of single crystal fibers of Pr:Lu3Al5O12 scintillator for gamma-ray imaging applications

Single-crystalline fibers were grown from 0.25, 0.70, and 1.50 mol% Pr-doped Lu₃Al₅O₁₂ (LuAG) melts by the micro-pulling down (μ-PD) method with a diameter of 0.3-0.5 mm and a length of about 200 mm. They were cut to 10 mm long specimens, and their scintillation properties, including light yield and decay time profile, were examined. These results were compared with corresponding properties of the specimens (0.8×0.8×10 mm³) cut from the bulk crystals produced by conventional Czochralski (CZ) growth. The μ-PD-grown fibers demonstrated relatively low light yield and had the same decay time constant when compared with those of the samples cut from the CZ-grown crystals. The fiber crystals were used to assemble scintillating arrays with dimensions of Ø 0.5×10 mm²×20 pixels and Ø 0.3×10 mm²×30 pixels coated by a BaSO₄ reflector. After optical coupling with a position sensitive photomultiplier tube, the fiber-based arrays demonstrated acceptable imaging capability with a spatial resolution of about 0.5 mm.     

Optical properties and gamma-ray response of Czochralski grown Pr:Lu3Al5O12 scintillating garnet crystals with different Pr content

Pr:LuAG single crystalline scintillators with different Pr³⁺ concentration, 0.1, 0.18, and 0.22 mol% were grown by the Czochralski method. The crystals were cut to dimensions of 2.2 × 2.2 × 15 mm³ and polished, simulating sensors for Positron Emission Tomography (PET). Their absorption coefficients were examined, and the absorption strength was found to be proportional to the Pr concentration. The α-ray induced emission spectra of the samples demonstrated two emission lines peaking at 310 and 370 nm. The emission intensities in the radio luminescence spectra were also proportional to the Pr content. The absolute light yields and intrinsic energy resolution under γ-ray irradiation were evaluated at +20, 0, and −20 °C using avalanche photodiode as a photodetector. Pr 0.22% doped crystal had strongest light output of 16 400 ph/MeV, and its intrinsic energy resolution was around few % at several hundred keV. When coupled with PMT, the decay time was around 25 ns, and it was almost independent on concentration.     

Characterization of LFS-3 scintillator in comparison with LSO

Performance of Lutetium Fine Silicate (LFS-3) scintillator in gamma-ray spectrometry has been investigated in comparison with the well known LSO crystal. The tests covered measurements of light output in terms of number of photoelectrons, energy resolution and non-proportionality. Time resolution was measured in coincidence experiments with 511 keV annihilation quanta from a ²²Na gamma source. Decay time constants of the light pulse were calculated on the basis of timing spectra obtained using Thomas-Bollinger single photon method. Afterglow was measured about 30 ms after the crystal was irradiated by a strong 13.9 GBq ²⁴¹Am source. Improvement in the energy resolution for 662 keV γ-rays from ¹³⁷Cs, shorter decay time constants and better time resolution were observed in case of LFS-3, when compared with LSO. For LFS-3 energy resolution for 662 keV from ¹³⁷Cs, decay time and time resolution were equal to about 7.66±0.23%, 40.5±1.2 ns and 161±5 ps, respectively, whereas for LSO the same parameters were equal to 8.13±0.23%, 43.9±1.3 ns and 173±5 ps, respectively. The study showed that LFS-3 crystal is an excellent substitute for LSO crystal.     

Development of cryogenic alpha spectrometers using metallic magnetic calorimeters

Cryogenic particle detectors have recently been adopted in radiation detection and measurement because of their high energy resolution. Many of these detectors have demonstrated energy resolutions better than the theoretical limit of semiconductor detectors. We report the development of a micro-fabricated magnetic calorimeter coupled to a large-area particle absorber. It is based on a planar, 1 mm² large paramagnetic temperature sensor made of sputtered Au:Er, which covers a superconducting meander-shaped pickup coil coupled to a low-noise dc-SQUID to monitor the magnetization of the sensor. A piece of gold foil of 2.5×2.5×0.07 mm³ was glued to the Au:Er film to serve as an absorber for incident alpha particles. The detector performance was investigated with an ²⁴¹Am source. The signal size comparison for alpha and gamma peaks with a large difference in energy demonstrated that the detector had good linear behavior. An energy resolution of 2.83±0.05 keV in FWHM was obtained for 5.5 MeV alpha particles.     

X-ray imaging using a consumer-grade digital camera

The recent advancements in consumer-grade digital camera technology and the introduction of high-resolution, high sensitivity CsBr:Eu²⁺ storage phosphor imaging plates make possible a new cost-effective technique for X-ray imaging. The imaging plate is bathed with red stimulating light by high-intensity light-emitting diodes, and the photostimulated image is captured with a digital single-lens reflex (SLR) camera. A blue band-pass optical filter blocks the stimulating red light but transmits the blue photostimulated luminescence. Using a Canon D5 Mk II camera and an f1.4 wide-angle lens, the optical image of a 240×180 mm² Konica CsBr:Eu²⁺ imaging plate from a position 230 mm in front of the camera lens can be focussed so as to laterally fill the 35×23.3 mm² camera sensor, and recorded in 2808×1872 pixel elements, corresponding to an equivalent pixel size on the plate of 88 μm. The analogue-to-digital conversion from the camera electronics is 13 bits, but the dynamic range of the imaging system as a whole is limited in practice by noise to about 2.5 orders of magnitude. The modulation transfer function falls to 0.2 at a spatial frequency of 2.2 line pairs/mm. The limiting factor of the spatial resolution is light scattering in the plate rather than the camera optics. The limiting factors for signal-to-noise ratio are shot noise in the light, and dark noise in the CMOS sensor. Good quality images of high-contrast objects can be recorded with doses of approximately 1 mGy. The CsBr:Eu²⁺ plate has approximately three times the readout sensitivity of a similar BaFBr:Eu²⁺ plate.     

Effects of packaging SrI2(Eu) scintillator crystals

Recent renewed emphasis placed on gamma-ray detectors for national security purposes has motivated researchers to identify and develop new scintillator materials capable of high energy resolution and growable to large sizes. We have discovered that SrI₂(Eu) has many desirable properties for gamma-ray detection and spectroscopy, including high light yield of ∼90,000 photons/MeV and excellent light yield proportionality. We have measured <2.7% FWHM at 662 keV with small detectors (<1 cm³) in direct contact with a photomultiplier tube, and ∼3% resolution at 662 keV is obtained for 1 in.³ crystals. Due to the hygroscopic nature of SrI₂(Eu), similar to NaI(Tl), proper packaging is required for field use. This work describes a systematic study performed to determine the key factors in the packaging process to optimize performance. These factors include proper polishing of the surface, the geometry of the crystal, reflector materials and windows. A technique based on use of a collimated ¹³⁷Cs source was developed to examine light collection uniformity. Employing this technique, we found that when the crystal is packaged properly, the variation in the pulse height at 662 keV from events near the bottom of the crystal compared to those near the top of the crystal could be reduced to <1%. This paper describes the design and engineering of our detector package in order to improve energy resolution of 1 in.³-scale SrI₂(Eu) crystals.     

Scintillation properties of Ce-doped LuLiF4 and LuScBO3

The crystals of 1 mol% Ce-doped LuLiF₄ (Ce:LLF) grown by the micro-pulling down (μ-PD) method and 1 mol% Ce-doped LuScBO₃ (Ce:LSBO) grown by the conventional Czochralski (Cz) method were examined for their scintillation properties. Ce:LLF and Ce:LSBO demonstrated ∼80% transparency at wavelengths longer than 300 and 400 nm, respectively. When excited by ²⁴¹Am α-ray to obtain radioactive luminescence spectra, Ce³⁺ 5d-4f emission peaks were detected at around 320 nm for Ce:LLF and at around 380 nm for Ce:LSBO. In Ce:LSBO, the host luminescence was also observed at 260 nm. By recording pulse height spectra under γ-ray irradiation, the absolute light yield of Ce:LLF and Ce:LSBO was measured to be 3600±400 and 4200±400 ph/MeV, respectively. Decay time kinetics was also investigated using a pulse X-ray equipped streak camera system. The main component of Ce:LLF was ∼320 ns and that of Ce:LSBO was ∼31 ns. In addition, the light yield non-proportionality and energy resolution against the γ-ray energy were evaluated.     

Small pixel CZT detector for hard X-ray spectroscopy

A new small pixel cadmium zinc telluride (CZT) detector has been developed for hard X-ray spectroscopy. The X-ray performance of four detectors is presented and the detectors are analysed in terms of the energy resolution of each pixel. The detectors were made from CZT crystals grown by the travelling heater method (THM) bonded to a 20×20 application specific integrated circuit (ASIC) and data acquisition (DAQ) system. The detectors had an array of 20×20 pixels on a 250 μm pitch, with each pixel gold-stud bonded to an energy resolving circuit in the ASIC. The DAQ system digitised the ASIC output with 14 bit resolution, performing offset corrections and data storage to disc in real time at up to 40,000 frames per second. The detector geometry and ASIC design was optimised for X-ray spectroscopy up to 150 keV and made use of the small pixel effect to preferentially measure the electron signal. A ²⁴¹Am source was used to measure the spectroscopic performance and uniformity of the detectors. The average energy resolution (FWHM at 59.54 keV) of each pixel ranged from 1.09±0.46 to 1.50±0.57 keV across the four detectors. The detectors showed good spectral performance and uniform response over almost all pixels in the 20×20 array. A large area 80×80 pixel detector will be built that will utilise the scalable design of the ASIC and the large areas of monolithic spectroscopic grade THM grown CZT that are now available. The large area detector will have the same performance as that demonstrated here.     

Growth and properties of UV nonlinear optical crystal ZnCd(SCN)4

A second-order nonlinear optical coordination crystal, zinc cadmium thiocyanate, ZnCd(SCN)₄ (ZCTC) was grown as a frequency doubler, emitting UV light. A large typical single crystal with dimensions up to 15×7×7 mm³ has been obtained by slow solvent-evaporation method for the first time. The infrared (IR) spectroscopy and X-ray powder diffraction (XRPD) of single crystals were performed at room temperature. The specific heat of the crystal has been measured to be 367.9 J/mol K at 300 K. The thermal expansion coefficients a- and c-oriented, have been measured to be −1.69×10⁻⁵ and 1.95×10⁻⁴ K⁻¹, respectively. The second harmonic generation (SHG) efficiency of ZCTC crystal is 51.6 times as high as that of urea reference, and the measured transmittance spectra from 190 to 3200 nm showed that the UV transparency cutoff occurs at 290 nm and the transmission is 73.22% at 380 nm. UV laser light of wavelength 380 nm has been achieved by the frequency doubling of a 760 nm laser diode at room temperature.     

Studies on the synthesis, structure, growth and physical properties of an organic NLO crystal: 2-Amino-5-nitropyridinium Phenolsulfonate

A noncentrosymmetric crystal was prepared from 2-amino-5-nitropyridine (2A5NP) and p-Phenolsulfonic acid, which was designed for second harmonic generation. Good quality single crystals of 2-amino-5-nitropyridinium Phenolsulfonate (2A5NPP) were successfully grown by the slow evaporation method with dimensions 10 × 4 × 3 mm³. The unit cell dimensions were determined from single crystal X-ray diffraction studies. The structural perfection of the grown crystals has been analyzed by high-resolution X-ray diffraction (HRXRD) rocking curve measurements. Fourier transform infrared (FTIR) spectral studies have been performed to identify the functional groups. The optical transmittance window and the lower cutoff wavelength of the 2A5NPP have been identified by UV-vis-NIR studies. Thermo gravimetric analysis (TGA) and differential thermal analysis (DTA) were used to study its thermal properties. Powder test with Nd:YAG laser radiation shows a high second harmonic generation. The laser induced surface damage threshold for the grown crystal was measured using Nd:YAG laser.     

Scintillation and optical properties of Pb-doped YCa4O(BO3)3 crystals

This communication reports optical properties and radiation responses of Pb²⁺ 0.5 and 1.0 mol%-doped YCa₄O(BO₃)₃ (YCOB) single crystals grown by the micro-pulling-down (μ-PD) method for neutron scintillator applications. The crystals had no impurity phases according to the results of X-ray powder diffraction. These Pb²⁺-doped crystals demonstrated blue-light luminescence at 330 nm because of Pb²⁺¹S₀-³P_0,1 transition in the photoluminescence spectra. The main emission decay component was determined to be about 250-260 ns under 260 nm excitation wavelength. When irradiated by a ²⁵²Cf source, the relative light yield of 0.5% Pb²⁺-doped crystal was about 300 ph/n that was determined using the light yield of a reference Li-glass scintillator.     

Development of an energy-binned photon-counting detector for X-ray and gamma-ray imaging

The aim of this study is to develop an energy-binned photon-counting (EBPC) detector that enables us to provide energy information of x-rays with a reasonable count statistics. We used Al-pixel/CdTe/Pt semiconductor detectors, which had an active area of 8 mm×144 mm and consisted of 18 modules aligned linearly. The size of a CdTe detector module was 8 mm×8 mm and the thickness of the CdTe crystal was 1 mm. Each module consisted of 40×40 pixels and the pixel size was 200 μm×200 μm. We applied the bias voltage of −500 V to the Pt common electrode. The detector counted the number of x-ray photons with four different energy windows, and output four energy-binned images with pixel depths of 12, 12, 11 and 10 bits at a frame rate of 1200 Hz (300 Hz×4 energy bins). The basic performance of the detector was evaluated in several experiments. The results showed that the detector realized the photon counting rate of 0.4×10⁶ counts/sec/pixel (10⁷ counts/sec/mm²), energy resolution 4.4% FWHM at 122 keV. The integral uniformity of the detector was about 1% and the differential uniformity was about 1%. In addition, the image quality was examined with a resolution chart and step-wedge phantoms made of aluminum and polymethyl methacrylate. And we compared the quality of an acquired image with that acquired with an energy integration detector. The results of these experiments showed that the developed detector had desirable intrinsic characteristics for x-ray photon counting imaging.     

Melt growth and characterization of Mg2Si bulk crystals

We have grown Mg₂Si bulk crystals by the vertical Bridgman method using a high-purity Mg (6N-up) source. The grown crystals were single-phase Mg₂Si and had well-developed grains (1-5 mm³). Laue observations and SEM-EDX observations confirmed that crystalline quality in the grains was single crystal with stoichiometric composition. Electron concentration of the single crystalline specimens grown from 6N-up-Mg was 4.0 × 10¹⁵ cm^− 3 at room temperature (RT). This value is more than one order of magnitude lower than that of specimens grown from 4N-Mg [(5-7) × 10¹⁶ cm^− 3]. The Hall mobility of 14,500 cm²/Vs was observed at 45 K in the crystals grown from 6N-up-Mg. We also found that Al impurity plays an important role in the crystals grown from a low-purity Mg source. From the optical absorption measurement, we estimated that the indirect energy gap was about 0.66 eV at 300 K and about 0.74 eV at 4 K.     

Crystal growth and scintillation characteristics of the Nd doped LiLuF4 single crystals

Sixty millimeter diameter single crystal of Nd³⁺ doped LiLuF₄ was successfully grown by the Czochralski technique. No remarkable absorption due to unfavorable impurities was observed from optical absorption measurements in the vacuum ultra-violet spectral region. The high crystallinity and homogeneous luminescence characteristics were found from X-ray rocking curve and cathode-ray luminescence respectively. X-ray excited luminescence spectrum was measured and the significant 4f²5d-4f³ luminescence at 182 nm was observed in the grown crystal. The pulse height spectrum was taken upon γ-ray irradiation. As a result, the grown crystals demonstrated sufficient response to the γ-ray showing the light yield of 420 ± 30 photons/MeV. The decay curve under α-ray irradiation was also investigated and described by two component decay kinetics which consists of the decay constants of 34 and 450 ns.     

Growth, thermal, dielectric and mechanical studies of triglycine zinc chloride, a semiorganic nonlinear optical material

Triglycine zinc chloride, a semiorganic material, has been grown by slow solvent evaporation technique from a mixture of aqueous solution of glycine and zinc chloride in 2:1 molar ratio at room temperature. The grown crystal is up to the dimension of 45 × 23 × 18 mm³. Characterization of the crystals was made using single-crystal X-ray diffraction for obtaining unit cell parameters. Powder X-ray diffraction was recorded and the major peaks were indexed. Simultaneous thermogravimetric analysis and differential thermal analysis were carried out for the as grown crystals to determine the thermal stability of the crystal. The crystals were further characterized by UV-Vis-NIR transmission spectrum in the range of 200 to 1100 nm. Dielectric constant and dielectric loss measurements were carried out at different temperatures and frequencies. Mechanical studies were carried out on the as grown crystal.     

Growth and properties of Ca0.28Ba0.72Nb2O6 single crystals

Calcium barium niobate Ca_0.28Ba_0.72Nb₂O₆ (CBN-28) crystals were successfully grown by the Czochralski method. X-ray powder diffraction experiments indicated that CBN single crystals are tetragonal with a = 12.432(±0.002) Å and c = 3.957(±0.001) Å, which have almost the same structure as the Sr_0.50Ba_0.50Nb₂O₆ (SBN-50) crystal. The thermal expansion coefficient perpendicular to Z-direction had been measured to be 1.25 × 10⁻⁵ K⁻¹ between 293.15 and 572.15 K, and along Z-axis was negative between 298.15 and 543.15 K. The specific heat of the crystal had been measured by the differential scanning calorimetric experiments. The transmittance spectra from 200 to 3200 nm were also measured. The measured temperature dependence of dielectric constants showed that the Curie temperature of the CBN-28 crystals is 260 °C, which is about 200 °C higher than that of the (SBN) crystal.     

Measurement of ultimate tensile strength and Young modulus in LYSO scintillating crystals

Scintillating crystals are employed in high energy physics, in medical imaging, diagnostic and security. Two mechanical properties of lutetium-yttrium oxyorthosilicate cerium-doped Lu_2(1−x)Y_2xSiO₅:Ce with x=0.1 (LYSO) crystals have been measured: the ultimate tensile stress (σ_UTS) and the Young elastic modulus (E). Measurements are made by means of a 4-points loading device and the experimental results account for an elastic-brittle stress-strain relation, which depends heavily on the specimen preparation and the material defects. σ_UTS along the [0 1 0] tensile direction ranges within 68.14 and 115.61 MPa, which, in the lowest case, is more than twice with respect to those measured for PbWO₄ (PWO), exhibiting a marked difference between the annealed and the not-annealed samples. The mean elastic modulus (E), along the same direction, is E=1.80×10¹¹ (±2.15×10¹⁰) N/m², with lower dispersion respect to UTS data. This type of analysis and study can be included into quality control procedures of crystals, based on samples taken out of production; such procedures can be established for industrial processing of crystals aimed to the high energy physics (calorimeters) and medical imaging (PET, etc.) applications.     

YAG(Ce) crystal characterization with proton beams

A YAG(Ce) crystal has been characterized with a proton beam up to 100 MeV. Tests were performed to investigate the possibility of using this detector as a proton calorimeter. A crystal size has been chosen that is able to stop up to 200 MeV. Energy resolution and light response have been measured at Laboratori Nazionali del Sud with a proton beam up to 60 MeV and a spatial homogeneity study of the crystal has been performed at Loma Linda University Medical Center with a 100 MeV proton beam. The YAG(Ce) crystal showed a good energy resolution equal to 3.7% at 60 MeV and measurements, performed in the 30-60 MeV proton energy range, were fitted by Birks' equation. Using a silicon tracker to determine the particle entry point in the crystal, a spatial homogeneity value of 1.7% in the light response has been measured.     

Growth and spectral properties of Er:NaGd(WO4)2 crystal

A high optical quality Er³⁺-doped NaGd(WO₄)₂ single crystal with dimensions of ∅18 × 50 mm³ has been grown using the Czochralski method. The structure of the grown crystal was proved by X-ray powder diffraction. The accurate concentration of Er³⁺ ion in the crystal was measured. The absorption spectra, fluorescence spectra and fluorescence lifetime of the crystal were measured at room temperature. Green up-conversion luminescence has been observed when the crystal is excited at 965 nm.