Polypropylene/silica micro‐ and nanocomposites modified with poly(styrene‐b‐ethylene‐co‐butylene‐b‐styrene)

The effects of different silica loadings and elastomeric content on interfacial properties, morphology and mechanical properties of polypropylene/silica 96/4 composites modified with 5, 10, 15, and 20 vol % of poly(styrene‐b‐ethylene‐co‐butylene‐b‐styrene) SEBS added to total composite volume were investigated. Four silica fillers differing in size (nano‐ vs. micro‐) and in surface properties (untreated vs. treated) were chosen as fillers. Elastomer SEBS was added as impact modifier and compatibilizer at the same time. The morphology of ternary polymer composites revealed by light and scanning electron microscopies was compared with morphology predicted models based on interfacial properties. The results indicated that general morphology of composite systems was determined primarily by interfacial properties, whereas the spherulitic morphology of polypropylene matrix was a result of two competitive effects: nucleation effect of filler and solidification effect of elastomer. Tensile and impact strength properties were mainly influenced by combined competetive effects of stiff filler and tough SEBS elastomer. Spherulitic morphology of polypropylene matrix might affect some mechanical properties additionally. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41486.     

Influence of thermoplastic elastomers on mechanical properties and morphologies of isotactic polypropene/glass bead hybrid composites

Glass bead-reinforced isotactic polypropene hybrid composites containing 0–20 vol % thermoplastic elastomers were prepared to study both structure/property relationship and morphology development. Polystyrene-block-poly(ethene-co-but-1-ene)-block-polystyrene (SEBS) and the corresponding block copolymer grafted with maleic anhydride (SEBS-g-MA) were used as thermoplastic elastomers. Hybrid composites containing SEBS gave higher Young's moduli than did those containing SEBS-g-MA. The experimental Young's moduli were in good agreement with the theoretical predictions according to Lewis and Nielsen. The lower moduli of hybrid composites containing SEBS-g-MA were attributed to interlayer formation and in situ encapsulation of glass beads, resulting in core–shell particles. This elastomeric interlayer impaired the filler reinforcement. Analysis of tensile yield stress and results of lap-shear tests confirmed strong filler–polymer interactions in composites containing SEBS-g-MA. Only in excess of a critical volume fraction did SEBS-g-MA afford a significant improvement of the notched Izod impact strength. In contrast to stiffness, Izod impact strength was not influenced by the type of elastomer and morphology. Investigation of crystallization and scanning electron microscopic studies proved the in situ encapsulation of the glass beads with SEBS-g-MA, whereas SEBS addition results in separately dispersed glass beads and SEBS microphases. © 1996 John Wiley & Sons, Inc.     

Influence of morphology on rheological and mechanical properties of SEBS-toughened,glass-bead-filled isotactic polypropene

The influence of morphology of glass-bead-filled isotactic polypropene containing 0–20 vol% thermoplastic elastomers (TPE) on mechanical and rheological properties was investigated. Polystyrene-block-poly(ethene-co-but-1-ene)-block-polystyrene(SEBS) and the corresponding block copolymer grafted with maleic anhydrid (SEBS-g-MA) were used as thermoplastic elastomers, realizing, in the first case, a three-phase morphology with separately dispersed glass beads and SEBS particles. In the second case, SEBS-g-MA forms an elastomeric interlayer between glass beads and polypropene matrix, comprising core–shell particles. Young's modulus and tensile yield stress of the hybrid composites decrease with an increase in TPE volume fraction due to low stiffness and strength of TPE. In comparison with the three-phase morphology of hybrid composites with SEBS, SEBS-g-MA interlayers effect a reduced stiffness of the hybrid composites but improve interfacial adhesion and, thus, tensile yield stress. Rheological storage and loss moduli increase with an increase in glass bead and TPE volume fraction. Due to improved interfacial adhesion, melt elasticity and viscosity are enhanced by the SEBS-g-MA interlayer when compared with separately dispersed SEBS. Consequently, the reduced stiffening effect of the glass beads due to SEBS-g-MA interlayer decreases mechanical elasticity, whereas improved interfacial adhesion, also promoted by the SEBS-g-MA interlayer, enhances tensile yield stress and melt elasticity. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 2499–2506, 1998     

Effect of Thermoplastic Elastomer on Melt Rheological and Fracture Behavior of Poly(Lactic Acid)

Poly(lactic acid) (PLA) was melt blended with thermoplastic elastomer, maleic anhydride grafted poly[styrene-b-(ethylene-co-butylene)-b-styrene] (SEBS-g-MA) copolymer with varied concentration (10–40?wt%) using twin screw extruder. Dynamic rheological behavior of PLA/SEBS-g-MA blends investigated a transition from liquid-like behavior to solid-like behavior in the composition range of 10–20?wt% of SEBS-g-MA. The capillary rheometer analysis showed enhanced shear viscosity with increase in SEBS-g-MA content. At 10?wt% of SEBS-g-MA, a maximum in the non-essential work of fracture was observed which reflects resistance to crack propagation. Scanning electron microscopy revealed a transition in deformation mechanisms from voids, to fibrillation and cavitation.     

Optimum toughening via a bicontinuous blending: toughening of PPO with SEBS and SEBS-g-maleic anhydride

The poly(2,6-dimethyl-1,4-phenylene oxide) (PPO) was toughened by melt extrusion through its blending with a styrene-b-ethylene/butadiene-b-styrene triblock copolymer (SEBS), or with maleic anhydride (MA) grafted SEBS (SEBS-g-MA). Their morphology, mechanical properties, and rheology have been investigated. Transmission electron microscopy revealed that both kinds of blends had an island-sea structure at low concentrations of SEBS or SEBS-g-MA and a bicontinuous one at sufficiently high concentrations. However, the percolation threshold was higher for SEBS than for the SEBS-g-MA. The Izod impact strength of PPO could be significantly improved through its blending with SEBS-g-MA, particularly in a blend with 20 wt% of SEBS-g-MA at which it had a maximum value. The rheological experiments indicated that the incorporation of SEBS increased and that of SEBS-g-MA decreased the melt viscosity of the system.     

Core/shell morphologies in recycled poly(ethylene terephthalate)/linear low-density polyethylene/poly(styrene-<Emphasis Type="Italic">b</Emphasis>-(ethylene-<Emphasis Type="Italic">co</Emphasis>-butylene)-<Emphasis Type="Italic">b</Emphasis>-styrene) ternary blends

Compatibilizer plays very important roles in preparing high performance polymer composites, not only for the ternary immiscible polymer blends, but also for the recycled and reused of waste plastics mixture. Generally, the compatibilizers can be used as the toughening agent in blending polymer materials. In the present work, the poly(styrene-b-(ethylene-co-butylene)-b-styrene) (SEBS) or maleic anhydride-grafted poly(styrene-b-(ethylene-co-butylene)-b-styrene) (SEBS-g-MA) acts as the compatibilizer and toughening agent for the preparation of R-PET/LDPE/SEBS (70/20/10) ternary blends. It must be pointed that the ternary blends are costlessly and conveniently prepared from the recycled poly(ethylene terephthalate) (R-PET) and linear low density polyethylene (LLDPE) through a melt blending in a co-rotating twin-screw extruder and injection moulded. The morphologies of the ternary blends are characterized by scanning electron microscopy (SEM). It was found that the blends contains reactive or non-reactive compatibilizer, the morphology originates from the LLDPE particles encapsulated by both SEBS and SEBS-g-MA. So, it results to the reduced interfacial tension between of the R-PET and SEBS-g-MA, in which the grafted chains of PET-g-SEBS-g-MA formed through in situ reaction between R-PET and SEBS-g-MA phases. Therefore, core–shell particles with smaller diameter disperse uniformly in the blends. Moreover, the good compatibilization and corresponding morphologies induce in balanced mechanical and thermal properties. DSC analysis show the dispersed phase particles could act as nucleating agent in the R-PET matrix, which results the improvement of the crystallization temperature. And it was also observed the decreased nucleation activity in graft copolymers in the R-PET/LLDPE/SEBS-g-MA blends. Notched Charpy impact strength and elongation at break are improved by the addition of compatibilizer.     

Influence of microstructure and flexibility of maleated styrene-b-(ethylene-co-butylene)-b-styrene rubber on the mechanical properties of polyamide 12

The present investigation deals with the mechanical and morphological properties of binary polyamide 12/maleic anhydride-grafted styrene-b-(ethylene-co-butylene)-b-styrene rubber (PA12/SEBS-g-MA) blends at varying dispersed phase (SEBS-g-MA) concentrations. Tensile behavior, impact strength and crystallinity of these blend systems were evaluated. Influence of microstructure, dispersed phase particle size, and ligament thickness on the impact toughness of the blend was studied. DSC data indicated an increase in crystallinity of PA12 in the blends. Tensile modulus and strength decreased while impact strength and elongation-at-break increased with the elastomer concentration. The enhanced properties were supported by interphase adhesion between the grafted maleic groups of rubber with polar moiety of polyamide 12. Analysis of the tensile data employing simple theoretical models showed the variation of stress concentration effect with blend composition.     

Morphology and mechanical properties of high‐impact polystyrene/elastomer/magnesium hydroxide composites

Ternary composites of high‐impact polystyrene (HIPS), elastomer, and magnesium hydroxide filler encapsulated by polystyrene were prepared to study the relationships between their structure and mechanical properties. Two kinds of morphology were formed. Separation of elastomer and filler was found when a nonpolar poly[styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene] triblock copolymer (SEBS) was incorporated. Encapsulation of filler by elastomer was achieved by using the corresponding maleinated SEBS (SEBS‐g‐MA). The mechanical properties of ternary composites were strongly dependent on microstructure. In this study, the composites with separate dispersion structure showed higher elongation, modulus and impact strength than those of encapsulation structure. Impact‐fracture surface observation showed that the toughening mechanism was mainly due to the massive cavitation and extensive matrix yielding. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102:5184–5190, 2006     

The effects of SEBS-g-maleic anhydride reaction on the morphology and properties of polypropylene/PA6/SEBS ternary blends

Ternary blends, based on 70% by weight of polypropylene (PP) with 30% by weight of a dispersed phase, consisting of 15% polyamide-6 (PA6) and 15% of a mixture comprising varying ratios of an unreactive poly[styrene-b-(ethylene-co-butylene)-b-styrene] (SEBS) triblock copolymer and a reactive maleic anhydride-grafted SEBS-g-MA, were produced via melt blending in a co-rotating twin-screw extruder. TEM revealed the blend containing only non-reactive SEBS to exhibit individual PA6 and SEBS dispersed phases. However, the progressive replacement of SEBS with reactive SEBS-g-MA increased the degree of interfacial reaction between the SEBS and PA6 phases, thus reducing interfacial tension and providing a driving force for encapsulation of the PA6 by the SEBS. Consequently, the dispersed-phase morphology was observed to transform from two separate phases to acorn-type composite particles, then to individual core-shell particles and finally to agglomerates of the core-shell particles. The resultant blends exhibited significant morphology-induced variations in both thermal and mechanical properties. DSC showed that blends in which the diameter of the PA6 particles was reduced to ≤3 μm by the increasing interfacial reaction exhibited fractionated PA6 crystallisation. In general, mechanical testing showed the blends to exhibit inferior low-strain tensile properties (modulus and yield stress) compared to the matrix PP, but superior ultimate tensile properties (stress and strain at break) and impact strength. These changes are discussed with reference to composite models.     

Morphology and flame‐retardancy properties of ternary high‐impact polystyrene/elastomer/polystyrene‐encapsulated magnesium hydroxide composites

The effects of elastomer type on the morphology, flammability, and mechanical properties of high‐impact polystyrene (HIPS)/polystyrene (PS)‐encapsulated magnesium hydroxide (MH) were investigated. The ternary composites were characterized by cone calorimetry, mechanical testing, and scanning electron microscopy. Morphology was controlled with poly[styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene] (SEBS) triblock copolymer or the corresponding maleinated poly[styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene] (SEBS‐g‐MA). The HIPS/SEBS/PS‐encapsulated MH composites exhibited separation of the filler and elastomer, whereas the HIPS/SEBS‐g‐MA/PS‐encapsulated MH composites exhibited encapsulation of the filler by SEBS‐g‐MA. The flame‐retardant and mechanical properties of the ternary composites were strongly dependent on microstructure. The composites with an encapsulation structure showed higher flame‐retardant properties than those with a separation structure at the optimum use level of SEBS‐g‐MA. Furthermore, the composites with a separation structure showed a higher modulus and impact strength than those with an encapsulation structure. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

Rheological behaviors of glass bead‐ and wollastonite‐filled polypropylene composites modified with thermoplastic elastomers

Steady‐ and oscillatory‐shear rheological behaviors of polypropylene/glass bead (PP/GB) and PP/wollastonite (PP/W) melts modified with thermoplastic elastomers, poly(styrene‐b‐ethylene‐co‐butylene‐b‐styrene) copolymer (SEBS) and the corresponding block copolymer grafted with maleic anhydride (SEBS‐g‐MA), were examined by means of a parallel‐plate rheometer. With adding the elastomers (SEBS and SEBS‐g‐MA) and fillers (spherical GB and acicular W) to PP, viscosity especially at low shear rates and shear‐thinning flow behavior at high shear rates were pronounced as evidenced quantitatively by Carreau–Yasuda (CY) parameters, but Cox–Merz analogy became weakened. Besides, melt‐elasticity in terminal region and relaxation time (t_c) in crossing point increased, indicating an enhancement in quasi‐solid behavior of molten PP. Comparing with the elastomers, rheological behaviors of molten PP were more influenced with adding the rigid fillers, especially with W due to distinct acicular shape of W particles. SEBS‐g‐MA elastomer more affected rheological behaviors of the ternary composites than SEBS elastomer, implying that SEBS elastomer and the filler particles behaved individually (i.e., development of separate microstructure) in (PP/GB)/SEBS and (PP/W)/SEBS ternary composites, but core‐shell microstructure developed with strong interfacial adhesion by adding SEBS‐g‐MA elastomer, and the filler particles encapsulated with the thick SEBS‐g‐MA elastomer interlayer (i.e., core‐shell particles) acted like neither big elastomer particles nor like individual rigid particles in melt‐state. Moreover, effects of SEBS‐g‐MA elastomer reached a maximum on rheological behaviors of (PP/W)/SEBS‐g‐MA ternary composite, indicating a synergy between core‐shell microstructure and acicular W particles. Correlations between oscillatory‐shear flow properties and microstructures of the blends and composites were evaluated using Cole–Cole (CC), Han–Chuang (HC), and van Gurp–Palmen (vGP) plots. COMPOS., 2012. © 2012 Society of Plastics     

Microstructural characteristics of glass bead‐ and wollastonite‐filled isotactic‐polypropylene composites modified with thermoplastic elastomers

Microstructural characteristics of isotactic‐polypropylene/glass bead (iPP/GB) and iPP/wollastonite (iPP/W) composites modified with thermoplastic elastomers, poly(styrene‐b‐ethylene‐co‐butylene‐b‐styrene) copolymer (SEBS) and corresponding block copolymer grafted with maleic anhydride (SEBS‐g‐MA), were investigated. Scanning electron microscopy (SEM), differential scanning calorimetry (DSC), and dynamic mechanical analyses (DMA) showed that the iPP/SEBS and iPP/SEBS‐g‐MA blends were partially compatible two‐phase systems. Well‐dispersed spherical GB and acicular W particles without evidence of interfacial adhesion were observed in the iPP/GB and iPP/W binary composites respectively. Contrary to the blends, melt flow rates of the iPP/GB and PP/W composites decreased more with SEBS‐g‐MA than with SEBS because of enhanced interfacial adhesion with SEBS‐g‐MA elastomer. The SEM analyses showed that the ternary composites containing SEBS exhibited separate dispersion of the rigid filler and elastomer particles (i.e., separate microstructure). However, SEBS‐g‐MA elastomer not only encapsulated the spherical GB and acicular W particles completely with strong interfacial adhesion (i.e., core‐shell microstructure) but also dispersed separately throughout iPP matrix. In accordance with the SEM observations, the DSC and DMA revealed quantitatively that the rigid filler and SEBS particles in iPP matrix acted individually, whereas the rigid filler particles in the ternary composites containing SEBS‐g‐MA acted like elastomer particles because of the thick elastomer interlayer around the filler particles. The Fourier transform infrared analyses revealed an esterification reaction inducing the strong interfacial adhesion between the SEBS‐g‐MA phase and the filler particles. POLYM. COMPOS., 31:1265–1284, 2010. © 2009 Society of Plastics Engineers     

Effect of extruder type on the properties and morphology of reactive blends based on polyamides

The morphology and mechanical properties of polyamide-based blends prepared in single and corotating twin-screw extruders were compared using transmission electron microscopy (TEM) techniques. Reactive polyamide blends with SEBS-g-MA (a maleated styrenic triblock copolymer with ethylene–butvlene midblocks), EPR-g-MA (a maleated ethylene/propylene rubber), and ABS were selected for the purpose of this investigation. For blends of SEBS-g-MA with difunctional (nylon x,y) polyamides (e.g., nylon 6,6; nylon 12,12), the twin-screw extruder was more effective in producing a finer dispersion of the rubber phase, which resulted in a significant lowering of the ductile–brittle transition temperature in case of the nylon 6,6 blend. On the other hand, blends of SEBS-g-MA with the mono-functional nylon 6 material led to rubber particles that were too small for toughening for both extruder types employed in this work. For nylon 6/EPR-g-MA blends, the single-screw extruder led to blends with excellent low-temperature impact properties for both single-step and masterbatch mixing techniques, whereas nylon 6/EPR-g-MA blends prepared in a single-step operation in the twin-screw extruder were brittle under ambient conditions. For difunctional polyamide blends with ABS (compatibilized with an imidized acrylic polymer), the morphology and mechanical properties were found to be independent of the extruder type employed for processing. © 1994 John Wiley & Sons, Inc.     

Toughness improvement of novel biobased aromatic polyamide/SEBS/organoclay ternary hybrids

Biobased aromatic polyamide/organoclay (Cloisite30B, C30B) nanocomposites were melt-compounded with reactive and nonreactive styrene–ethylene–butylene–styrene (SEBS) rubbers at different weight contents to form ternary and quaternary blends. The mechanical properties were investigated as a function of the blend composition. The elongation at break and the impact strength increase with increasing SEBS rubber content, whereas the Young's modulus logically decreases proportionally to SEBS amount. Extra addition of SEBS grafted maleic anhydride (SEBS-g-MA) induces a synergistic effect. The SEBS-g-MA makes it possible to limit the aforementioned rigidity loss and to greatly increase the impact strength. The critical strain energy release rate increases significantly when both reactive and nonreactive rubbers are combined. Three types of microstructures appear depending on the blend composition: (1) small and numerous well-dispersed particles when reactive rubber is used, (2) about 10 times bigger and less numerous well-dispersed particles in the case of nonreactive rubber, and (3) a flocculated dispersion of small particles when both reactive and nonreactive rubber are added. Finally, the polyamide performances were significantly increased when the flocculated morphology was noticed due to a better PAXD/SEBS interfacial adhesion given by the SEBS-g-MA compatibilization and to a thinner rubber distribution in the matrix. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48888.     

Compatibilization of PP/elastomer/microsilica composites with functionalized polyolefins: Effect on microstructure and mechanical properties

The morphology and mechanical properties of polypropylene/elastomer/silica composites were investigated with the aim of improving stiffness and impact resistance. Two different types of silica were tested: Precipitated silica and polymer grade microsilica (silica fume). The composites were compatibilized with commercial polypropylene and polyethylene containing maleic anhydride functionality as a means of controlling their microstructure and ultimately their mechanical properties. Comparisons were made with surface coated silica and hydroxyl-functionalized copolymers prepared with metallocene catalysts. The effect of adding the polymeric compatibilizers was assessed by morphology studies, thermal analysis and mechanical testing. Significant improvements in impact strength were obtained by tailoring the microstructure of polypropylene/elastomer/microsilica composites. With introduction of PP-g-MAH as compatibilizer, stiffness was enhanced simultaneously with impact strength. DSC curves of crystallization provided evidence to support the formation of different microstructures.     

Largely improved toughness of PP/EPDM blends by adding nano-SiO2 particles

As a part of long-term project aimed at super polyolefin blends, in this work, we report the toughness and phase morphology of polypropylene (PP)/EPDM/SiO₂ ternary composites. Two processing methods were employed to prepare PP/elastomer/filler ternary composites. One was called one-step processing method, in which the elastomer and the filler directly melt blended with PP matrix. Another one was called two-step processing method, in which the elastomer and the filler were mixed first, and then melt blended with pure PP. Two kinds of PP (grafted without or with maleic anhydride (PP-g-MA)) and SiO₂ (treated with or without coupling agent) were used to control the interfacial interaction among the components. The dependence of the phase morphology on interfacial interaction and processing method was investigated. It was found that the formation of filler-network structure could be a key for a simultaneous enhancement of toughness and modulus of PP and its formation seemed to be dependent on the work of adhesion (W_AB) and processing method. As the W_AB of PP/EPDM interface was much lower than that of PP/SiO₂ and EPDM/SiO₂, and the two-step processing method was used, the formation of filler-network structure was favorable. In this case, a super toughened PP ternary composite with the Izod impact strength 2-3 times higher than PP/EPDM binary blend and 15-20 times higher than pure PP could be achieved.     

The effects of PHBV-g-MA compatibilizer on morphology and properties of poly(3-hydroxybutyrate-Co-3-hydroxyvalerate)/olive husk flour composites

The paper provides some experimental data on the effects of a poly(3-hydroxybutyrate-co-3-hydroxyvalerate) grafted maleic anhydride (PHBV-g-MA) used as the compatibilizer for poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV)/olive husk flour (OHF) composites prepared by melt compounding. The natural filler was added to PHBV at various contents, i.e. 10, 20, and 30 wt%, while the amount of PHBV-g-MA was 5 wt% based on neat PHBV. Morphology, contact angle measurements, water absorption (WA), mechanical, viscoelastic, and barrier properties of the various composites were investigated with and without the compatibilizer. The study showed through scanning electron microscopy that the addition of PHBV-g-MA to PHBV/OHF composites resulted in better and finer dispersion of the filler in the matrix, even at a higher content ratio, indicating improved affinity between the components. This is in agreement with the decrease in both surface energy and WA. Furthermore, tensile and dynamic mechanical measurements indicated a reinforcing effect of OHF in PHBV composites, being more pronounced in the presence of PHBV-g-MA. The barrier properties against oxygen and water vapor were also improved for the compatibilized composites.     

Wide-angle X-ray diffraction investigation on crystallization behavior of PA6/PS/SEBS-g-MA blends

Blends of polystyrene/polyamide 6 (PS/PA6) compatibilized by styrene-ethylene/butylene-styrene (SEBS) elastomer grafted with maleic anhydride were prepared by melt blending. Wide-angle X-ray diffraction (WAXD) scans indicated a skin–core structure formed in the specimens during the injection-molding process. The results showed that the specimens tended to form the α-crystalline form in the core region, but the γ-crystalline form in the skin region. The influences of PS and SEBS-g-MA on the crystallization of PA6 were different in the core region and skin region. In the core region, PS made the PA6 tend to be in the γ-crystalline form, but the influence of PS was contrary in the skin region. SEBS-g-MA had both enhancement and toughening effects on the blends. The mechanical properties of the blends were determined by the combined action of the two aforementioned factors.     

Interfacial modification of high impact polystyrene magnesium hydroxide composites effects on flame retardancy properties

High impact polystyrene (HIPS)/magnesium hydroxide (MH) composites were prepared by melt‐blending. Two kinds of interfacial modifiers were used in this research, maleinated poly[styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene] (SEBS‐g‐MA) triblock copolymer and PS. The effects of the use levels of SEBS‐g‐MA on the flame retardancy of HIPS/elastomer/MH based on unmodified and PS‐modified surface were investigated by TEM, FTIR, and combustion tests (horizontal burning test and cone calorimetry). The combustion results showed that comparing composites containing unmodified MH, the flame retarding properties of composites containing PS‐modified MH were obviously improved. The increased performance can be explained that the PS covered on the surface of MH could further improve dispersion of the filler in matrix. Furthermore, there existed a critical thickness of interfacial boundary for optimum flame‐retarding properties in both ternary composites based MH and PS‐modified MH. When the interfacial boundary relative thickness is less than 0.53, the introduction of SEBS‐g‐MA can improve the dispersion degree, leading the improvement of flame retardancy properties. However, with the increase of interfacial boundary thickness, the SEBS‐g‐MA coating around MH acted as a heat and mass transfer barrier, leading to the reduction of flame retardancy. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Effects of electron beam irradiation on the structure–property behavior of blends based on low density polyethylene and styrene-ethylene-butylene-styrene-block copolymers

Low density polyethylene (LDPE) blends with different additives were exposed to various doses of electron beam irradiation. The additives used were styrene-ethylene-butylene-styrene-block copolymers (SEBS), styrene-ethylene-butylene-styrene-block copolymer grafted with maleic anhydride (SEBS-g-MA) and mineral compounds. The structure–property behavior of electron beam irradiated blends was characterized in terms of mechanical, thermal, and electrical resistivity properties. The results indicated that the unirradiated LDPE blends with the different compositions showed improved mechanical properties, thermal and volume resistivity properties than pure LDPE. However, the improvement in properties of unirradiated blends by using SEBS-g-MA was higher than using SEBS copolymer. Further improvement in the mechanical, thermal and electrical properties of the LDPE blends was achieved after electron beam irradiation. The limited oxygen index (LOI) data revealed that the LDPE/SEBS-g-MA/ATH blend was changed from combustible to self-extinguishing material after electron beam irradiation to a dose of 100 kGy. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012