Ta离子注入Ti6Al4V合金的抗腐蚀性能

用注量为1.2×1016、3×1016、1.5×1017、3×1017、4.5×1017/cm2的Ta离子对Ti6Al4V合金进行表面改性,加速电压为146.5 keV。Ta离子注入后,用动电位极化曲线研究其抗Hank’s溶液腐蚀性能,用小角掠射X射线衍射研究其表面物相结构,用X射线光电子能谱分析其腐蚀样品的表面元素化合态。结果表明,Ta离子注入改善了Ti6Al4V合金抗Hank’s溶液腐蚀性能,但试样的腐蚀电流密度并非随Ta离子注量增加而单调减小,试样表面合金层、单质Ta和氧化物,共同形成腐蚀阻挡层,提高其抗腐蚀性能。     

高能重离子辐照制备碳氮化合物材料研究

室温下,先用100-120 keV的N离子注入类金刚石薄膜和石墨中,注入剂量5×1017至5×1018 cm-2,再用高能Xe、U、C60离子分别辐照注氮后的样品,然后用显微FTIR和Raman、XRD/XPS等手段进行分析表征,研究了实验样品中由辐照引起的新化学键和新相的产生.实验结果显示,高能重离子辐照可在所有样品中产生大量的CN键,高N浓度和大密度能量沉积导致sp3/sp2键比率的增加以及形成α-和β-C3N4必需的N-sp3C键的量的增加.C60离子辐照在注氮石墨样品中引起了ta-C、N=sp2C和N-sp3C键的形成;而高能离子辐照在注氮类金刚石薄膜样品中产生了α-和β-C3N4晶态夹杂物,其尺寸在1.4-3.6 nm之间.     

国产RPV钢质子辐照的巴克豪森噪声研究

采用240 ke V质子对国产反应堆压力容器(RPV)钢试样进行辐照。辐照注量为0.25×1017~5×1017cm-2(对应位移损伤量0.05~1 dpa)范围。对辐照试验分别进行巴克豪森噪声(MBN)检测和辐照样品的显微硬度测试,研究MBN信号与辐照注量和力学性能之间的关系。结果表明:MBN信号对辐照缺陷非常敏感,随着辐照损伤量增加MBN信号先快速降低,随后又开始升高,并在0.3~1 dpa区间变化趋于缓和。上述变化主要归因于材料内部磁畴壁与质子辐照缺陷的相互作用。显微硬度测试表明:质子辐照后材料呈显著的辐照硬化趋势;同时通过显微硬度与MBN信号对比发现,MBN信号与显微硬度存在显著的线性关系。     

GCr15表面钽沉积及碳离子注入的摩擦性能的研究

GCr15钢广泛用于各类轴承制造.为提高其摩擦性能,用磁控溅射法在GCr15轴承钢试样表面沉积厚约100 nm的钽膜,再进行不同注量的50 keV碳离子注入.用Ф6的GCr15钢球做对磨试验,测试它们的摩擦性能,用SEM观察磨痕形貌.结果表明,处理后GCr15钢改性层的Ta2C含量随注量增加,摩擦性能得以提高.载荷1 N、滑动速度50 mm/s条件下,注入3×1017ions/cm2的试样耐磨性是原始试样的1.65倍;表面沉积钽膜后,摩擦系数由未处理前的0.8～1下降至0.5左右,钽膜注碳后摩擦系数更降至0.2～0.3,注入层主要以磨粒磨损为主.     

电子束和离子注入处理鸡冠花种子对当代(Mo)植株生长发育影响的初步研究

利用电子束和氮离子、氢离子注入处理普通鸡冠花干种子,试验结果表明,两种诱变处理均能显著抑制鸡冠花植株的生长、发育,并能有效地诱发花性状变异,变异株率可达0.5%—2%。电子束处理鸡冠花干种子的半致死剂量(LD50)经测定为1.2kGy左右;离子注入处理的半致死剂量随注入离子种类不同而不同,N 注入的半致死剂量(LD50)为1.6×1017/cm2,H 注入的半致死剂量应低于1.6×1016/cm2。鸡冠花干种子电子束处理的适宜剂量为1.5kGy左右,离子注入处理的适宜方法是N 1.6×1016/cm2。同时鸡冠花对高剂量辐照较不敏感,是一种耐强辐照的资源。     

Ar+离子辐照对锆4合金耐腐蚀性能的影响

为了研究辐照损伤对锆4合金电化学耐腐蚀性能的影响,使用直线加速器产生单电荷载能Ar+,在液氮温度下辐照样品表面,产生缺陷.然后,测量辐照后锆4合金的电化学极化曲线,使用钝化电流密度作为评定腐蚀性能的指标,分析不同注量Ar+离子辐照对锆4合金钝化电流密度的影响.同时使用透射电子显微镜分析不同注量Ar+辐照下锆4合金损伤层的微观结构.实验结果表明在低离子注量范围内(＜3×1014/cm2),随着辐照量的增加钝化电流密度升高,耐腐蚀性能降低;在中等离子注量范围内(3×1014-1×1016/cm2),随着辐照量的增加钝化电流密度急速下降,耐腐蚀性能显著提高;在高离子注量范围内(1×1016-1×1017/cm2),随着辐照量的增加钝化电流密度又开始增加,耐腐蚀性能再次降低.最后,根据原子碰撞理论对实验结果进行了理论分析.     

多束动态混合注入技术制备TiN厚膜的工艺、结构及性能研究

在多束动态混合(MBMI)-注入系统上利用MBMI技术制备TiN膜,XRD分析表明,N入射角度α(o)、氮钛原子到达比RN/Ti、N2分压PN2对膜生长的择优取向及相结构有影响;性能研究结果表明,高的入射离子能量Ei、基体温度Ts以及合适的RN/Ti对TiN膜的显微硬度HK和膜 -基结合力都有正面影响。     

N+注入对甘草叶片腺体和腺体分泌多糖及叶片多糖的影响

甘草叶片上生长有能分泌多糖的腺体,腺体分泌的多糖液累积于腺体头部呈透明"球状",功能叶上所有的腺体均向腺体头部分泌多糖液,枯黄衰老叶上的腺体头部仍然具有完整的呈"球状"的多糖液.对甘草干种子注入总量为4.68×1016/cm2、能量为10-25keV的N 对甘草叶片腺体数、腺体分泌多糖、叶内多糖、叶片总多糖均有刺激效应.其中15 keV的N 注入叶片腺体分泌多糖比对照提高44.1%(P＜0.01);甘草叶面腺体数和腺体分泌多糖呈明显的正相关(r=0.4537,P＜0.1).20keV的N 注入甘草叶片总多糖含量比对照提高31.8%(P＜0.01).这些N 注入甘草干种子的能量、注量参数可供对甘草进行离子束育种时参考.     

B、N、Cr、Mo离子注入对纯铁抗腐蚀性能和显微硬度的影响

本文介绍B、N、Cr、Mo离子注入到纯铁中形成的表面合金的腐蚀性能和显微硬度。在0.5mol/lH_2SO_4溶液中的自然腐蚀电位变化不大,临界钝化电流密度和维持电流密度明显降低,钝化范围扩大,显微硬度提高。几种离子组合注入比单一离子注入的效果好。     

铈离子注入Zr-4合金的高温氧化行为

研究铈离子注入对Zr4合金氧化性能的影响，对Zr—4合金表面注入了不同剂量的铈离子，并在500℃条件下进行了空气氧化实验。氧化曲线表明，铈离子注入能明显改善Zr—4合金的氧化性能，且注量越高，氧化性能改善的程度也越大。运用俄歇电子（AES)、X光电子（XPS)和小角掠射X光衍射技术(GAXRD)等测试方法分别分析了注入样品表层元素的深度分布、氧化膜成分及相结构，同时探讨了铈离子注入改善Zr—4合金氧化性能的机制。     

Identification of radiation treatment of wheat （Triticum aestivum. L）and rice （Oryza sativa. L） samples using thermoluminescence of contaminating minerals

Food irradiation is gaining popularity worldwide and this technology is important to improve quality and reduce the post harvest losses of food. Because of the rapid commercialization of irradiated foods throughout the world, compliance of different regulations relating to use of technology in different countries and demand of consumers for clear labelling of irradiated foods, there is need for the development of analytical methods to detect radiation treatment of food. Among several methods studied so far, thermoluminescence （TL） is an important method that can be used to find out the irradiation history of food that contain even a very minute amount of dust particles. In this study, the irradiated and unirradiated wheat and rice samples were analyzed using the TL method. The samples were purchased from the local market of Peshawar and irradiated to radiation doses of 0.5 and 1.0 kGy using Co-60 gamma irradiator at the Nuclear Institute for Food and Agriculture （NIFA）, Peshawar. The mineral contaminants were isolated by jet water, ultrasonic treatment, and density gradient. TL glow curves of the isolated minerals from irradiated and unirradiated samples were recorded between the temperature ranges of 50-500℃ using a TL reader. Generally, the glow curves for irradiated samples showed much higher TL intensities （TL1） than the unirradiated samples. The results were normalized by rerradiation of mineral samples to gamma-ray dose of 1.0 kGy followed by determination of the second glow curves （TL2）. The ratio of the area of first glow curve to that of second glow curve （TL1/TL2） was calculated for selected temperature intervals and compared with the recommended values for unirradiated and irradiated samples. Finally, the shapes of the glow curves for irradiated and unirradiated samples were also analyzed. On the basis of these results （comparison of TL-intensities, TL1/TL2 ratios and shapes of the glow curves）, all the irradiated and unirradiated samples of wheat and rice were unequivocally identified.     

Preparation of Zn/TiO2 powder and its photocatalytic performance for oxidation of P-nitrophenol

Zn-doped TiO2 catalysts were prepared using a sol-gel method and characterized by XPS,UV-Vis, BET, XRD in this study. Under the irradiation of simulant sunlight, the photocatalytic activity for the degradation of p-nitrophenol was studied too. After irradiation for 2.5 h, the degradation percentage of p-nitrophenol could rise to more than 80 %. The results showed that the spectrum absorption band edge of Zn/TiO2 powder does not broaden obviously comparing with pure TiO2 powder. Zinc exists as Zn （11）. When calcined at 973 K, there is a new phase as ZnTiO3 in Zn/TiO2 catalyst. The order of photocatalytic activity of Zn/TiO2 catalysts calcined at different temperatures for p-nitrophenol is 773 K 〉 673 K 〉 873 K 〉 573 K 〉 973 K and the photocatalytic activity of Zn/TiO2 catalyst calcined at 773 K is better than TiO2 catalysts heated at the same temperature, and outclasses that of commercial TiO2 catalyst. It also showed that the photocatalytic degradation of p-nitrophenol follows first-order kinetics under the irradiation of simulant sunlight.     

Current status of radiation therapy for prostate cancer

Radiotherapy for the treatment of prostate cancer has been extensively explored in the past. Along with the comprehensive understanding of the biology of prostate cancer and rapid advances in terms of technology, the out- come of treatment for the patients with prostate cancer has improved. The authors review radiotherapy as the primary treatment for the disease, with particular emphasis on the technological advances from both the radiobiological and radiophysics aspects. Nonconventional fractionated irradiation like hyper- or hypo-fractionation has been imple- mented in the clinic, the final results still need to be confirmed in the future. Technological advances like IMRT, IGRT, in the last two decades have significantly improved the delivery of external radiotherapy to the prostate. This has re- sulted in an overall increase in the total dose that can be safely delivered to the prostate, which has led to modest im- provements in the biochemical outcome. However, establishing the standard therapy for prostate cancer remains con- troversial. It is hoped that the next decades will bring continued advances in the development of biologicals that will further improve current clinical outcomes.     

The control system for SSRF injection and extraction

This paper introduces the injection and extraction control system design for SSRF,which is a distributed control system aimed at stability and reliability of the pulse power supplies,PPS(Personnel Protection System)and MPS(Machine Protection System).The hardware environment is mainly based on PLC(Programmable Logic Con- troller),and ARM(Advanced RISC Machine)is also applied for studying stability of the power supplies.WinCC and EPICS(Experimental Physics and Industrial Control System)have been selected as the platforms of SCADA(Super- visory Control and Data Acquisition).For unifying the interfacing to the control computer,all front-end equipments are connected via Industrial Ethemet.     

水平管内含空气蒸汽强制对流冷凝换热模型研究

为研究含空气蒸汽在水平管内强制对流冷凝换热特性,基于对传热传质过程的分析,建立了管内为环状流与波状流条件下的流动冷凝换热模型。从潜热、显热和液膜3个环节对整个换热过程进行建模,最终得到计算局部冷凝换热系数的理论关系式。模型预测结果与实验数据的对比表明,二者相对偏差在±20%以内,验证了该换热模型的准确性与适用性。通过进一步的研究发现：从换热管入口至出口,随着冷凝的进行,管内换热主要热阻由液膜热阻向气液界面的凝结热阻转变;主流气体对流换热过程基本可忽略。     

The preclinical pharmacological study of dopamine transporter imaging agent 18F-FP-β-CIT

The paper is to study pharmacologic characteristics of 18F-FP-β-CIT (18F-N-(3-fluoropropyl)-2β- carbomethoxy-3β- (4-iodophenyl)nortropane) as an imaging agent for dopamine transporter. The radiochemical purity of 18F-FP-β-CIT in aqueous solution was over 95% after standing at room temperature for 4h. Biodistribution displayed rapid uptake in rat brain (1.375 %ID/organ at 5min and 0.100 %ID/organ at 180 min) and the striatal uptake was 1.444,0.731, 0.397, 0.230 and 0.146 %ID/g at 5, 30, 60, 120 and 180 min, respectively. The values of striatum/cerebellum,striatum/frontal cortex and striatum / hippocampus in rat's brain at 30 min were 3.38, 2.17 and 2.40 respectively. The uptake in striatum can be blocked by β-CFT, suggesting that 18F-FP-β-CIT binds to DAT peculiarly. The compound was rapidly cleared from monkey's blood. The striatal uptake was bilaterally decreased in the left-sided lesioned PD rats, compared with normal control. Brain PET imaging studies in normal monkey showed that 18F-FP-β-CIT was concentrated in striatum. The test of undue toxicity showed that the dose received by mice was 1250 times as by human, which indicates that 18F-FP-β-CIT is very safe. So 18F-FP-β-CIT is a promising PET imaging agent for DAT with safety and validity.     

Web Services interface of SSRF archive data analysis system

Accelerator database stores various static parameters and real-time data of accelerator. SSRF (Shanghai Synchrotron Radiation Facility) adopts relational database to save the data. We developed a data retrieval system based on XML Web Services for accessing the archive data. It includes a bottom layer interface and an interface applicable for accelerator physics. Client samples exemplifying how to consume the interface are given. The users can browse, retrieve and plot data by the client samples. Also, we give a method to test its stability. The test result and performance are described.     

Investigations on landmine detection by BF3 detector

Experiments were carried out to investigate the possible use of neutron backscattering for the detection of polyethylene (PE) sample buried in the soil. In detection of landmine by neutrons, the neutron detector and its shield play an important role. In this paper, the effects of graphite, heavy water, polyethylene and boric acid moderators on the flux of back scattered neutrons were investigated. We have also experimentally verified the effect of BF3 detector shield and obtained good agreement with theory.     

PLASMA SCIENCE AND TECHNOLOGY AUTHOR INDEX TO VOLUME 16(2014)

正~~     

Radioactivity levels in soil of salt field area,Kelambakkam,Tamilnadu,India

Soil samples in and around salt field area have been analyzed for natural radioactivity concentration using gamma ray spectrometer.The activity concentration for ~(232)Th,~(238)U and ~(40)K are ranged from 27.88 to 45.27 Bq/kg, from BDL to 13.30 Bq/kg,and from 135.54 to 381.28 Bq/kg,respectively.The measured activity concentrations for these radionuclides were compared with world average activity of soil.The average activity concentration of ~(232)Th in the present study is 1.19 times higher than world median value while the activity of ~(238)U and ~(40)K is found to be lower. The absorbed dose rates due to these radionuclides were calculated.The average absorbed gamma dose rate due to the presence of ~(232)Th,~(238)U and ~(40)K in soil samples is 36.99 nGy·h~(-1).These results indicate no radiological anomaly. The data presented in this study will serve as a base line survey for primordial radionuclides concentration in the study area.