Structure of Pb(Zr,Ti)O_3(PZT) for Power Ultrasonic Transducer

To improve the performance of ultrasonic transducer, the samples of PZT were improved by doping. The doped PZT was observed and analyzed from the following aspects: the crystal phase structures, the surface morphologies and the dielectric constant. According to the transducer parameter requirements for ultrasonic machining, there are also requirements for the parameters of piezoelectric ceramics. The high performance PZT was prepared by doping the elements of Ga, Ba, Nb, Sn, and Sr in PZT. The doped PZT is suitable for power ultrasonic machining at 20 kHz through analysis using X-ray diffraction(XPD), a scanning electron microscope(SEM) and LCR meter. Therefore, the excellent performance of transducer for power ultrasonic machining is guaranteed.     

Low Temperature Synthesis of （Pb,La）（Zr,Sn,Ti）O3 Powders by Citrate Process

Lead lanthanum zirconate stannate titanate （PLZST） powders with homogeneous composition were synthesized at a relatively low temperature of 650 ℃ by a citrate process based on the Pechini method. Clear aqueous solutions were prepared from inorganic salts, and citric acid was added as a chelating agent to attain precursor sols. Dried gel-precursors were calcined at different temperatures for various time. The perovskites powders were obtained at 650 ℃ for 1 hour. XRD and SEM results show that the powders were single-phase and ultrafine particles.     

Solid Solution Characteristics of Pb（B1/3Nb2/3）O3-bascd Composite Ceramics

The solid solution characteristics of Pb（B1/3Nb2/3）O3-based （B=Zn^2＋, Mg^2＋, Ni^2＋） composite ceramics prepared by two-phase mixed-sintering method were developed based on dielectric measurements. Results show that there are double dielectric peaks for PZN-based composite ceramic, implying two phases coexist. However single dielectric peak was presented in PMN- and PNN-based composite ceramics, respectively. It is indicated that obvious solid solution reaction exists during the sintering process of these two systems. The effects of B-site ion difference on the solid solution characteristics were discussed by crystal chemistry. SEM was employed to investigated the microstructures of composite ceramics. The influences of solid solution reaction on grain growth were discussed.     

Effect of ZnO-B<Subscript>2</Subscript>O<Subscript>3</Subscript> glass addition on the microwave dielectric properties of BaO-Nd<Subscript>2</Subscript>O<Subscript>3</Subscript>-TiO<Subscript>2</Subscript>-Bi<Subscript>2</Subscript>O<Subscript>3</Subscript> system

The effect of ZnO-B₂O₃(ZB) glass addition on the sintering behavior, microstructures and microwave dielectric properties of BaO-Nd₂O₃-TiO₂-Bi₂O₃ (BNTB) system was investigated with the aid of X-ray diffraction, scanning electron microscopy and capacitance meter. It is found that the ZB glass addition, acting as a sintering aid, can effectively lower the sintering temperature of BNTB system to 850 °C. The dielectric constant of BNTB-ZB ceramics increases with the increase of soaking time and the value of dielectric loss decreased with increasing soak time. The optical dielectric properties at 1 GHz of ɛ=74, tan δ=4×10⁻⁴, and TCC=25 ppm/°c were obtained for the BNTB system doped with 25 wt% ZB glass sintered at 850 °C for 2 h, representing that the BNTB-ZB ceramics could be promising for multilayer low temperature co-fired ceramics applications.     

Structure,Electrical Conducting and Thermal Expansion Properties of Ln0.6Sr0.4Co0.8Fe0.2O3 （Ln = La,Pr, Nd,Sm） Ceramics

Ln0.6Sr0.4Co0.2Fe0.2O3 （Ln=La, Pr, Nd, Sm） perovskite-type complex oxides were synthesized using a glycine-nitrate process, and the structure, electrical conducting and thermal expansion properties of the resulting ceramics were examined with regard to the nature of the lanthanide cations. The results indicated that the La, Pr and Nd specimens had a rhombohedral symmetry, while an orthorhombic structure was determined for the Sm specimen. The pseudo-cubic lattice constant decreased with smaller lanthanide cations. It was found that the electrical conducting properties declined with decreasing lanthanide cation size. Fortunately, all the compositions remained rather high electrical conductivities exceeding 650 Ω ^-1m·cm^-1 in the intermediate temperature range （600-800 ℃）. An appreciable thermal expansion increase at high temperatures was detected for all the compositions. Decreasing the size of the lanthanide cations resulted in an increase of thermal expansion. With respect to the high electrical conductivities, the Ln0.6Sr0.4Co0.8Fe0.2O3 oxides are considered to be acceptable as mixed conducting component in composite cathode designs together with doped ceria electrolytes.     

Direct synthesis of Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-modified Li(Ni<Subscript>0.5</Subscript>Co<Subscript>0.2</Subscript>Mn<Subscript>0.3</Subscript>)O<Subscript>2</Subscript> cathode materials for lithium ion batteries

To improve the cyclic stability at high temperature and thermal stability, the spherical Al₂O₃-modified Li(Ni_0.5Co_0.2Mn_0.3)O₂ was synthesized by a modified co-precipitation method, and the physical and electrochemical properties were studied. The TEM images showed that Li(Ni_0.5Co_0.2Mn_0.3)O₂ was modified successfully with nano-Al₂O₃. The discharge capacity retention of Al₂O₃-modified Li(Ni_0.5Co_0.2Mn_0.3)O₂ maintained about 99% after 200 cycles at high temperature (55 °C), while that of the bare one was only 86%. Also, unlike bare Li(Ni_0.5Co_0.2Mn_0.3)O₂, the Al₂O₃-modified material cathode exhibited good thermal stability.     

Synthesis and characterization of a new Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> pillared triple-layered perovskite KSr<Subscript>2</Subscript>Nb<Subscript>3</Subscript>O<Subscript>10</Subscript>

A n-Hexyl NH₃Sr₂Nb₃O₁₀ is obtained by the stepwise ion-exchange reaction, then is dispersed in aqueous solution of trinuclear acetato-hydroxo iron (III) nitrate, [Fe₃(OCOCH₃)₇OH·2H₂O]NO₃, and the interlayer potassium cations of the perovskite niobate are exchanged with the partially hydrolyzed trinuclear acetato complex ions. On heating, the exchanged complex ions are converted into iron oxide pillars which keep the perovskite sheets apart. The product is characterized by XRD, SEM, EDAX and surface area measurement respectively. Zhang Hui: Born in 1970 Funded by the National Natural Science Foundation of China (No. 50002007), Major Program of Ministry of Education (No. 0201) and Open Foundation of State Key Lab of Advanced Tech. for Materials Synthesis and Processing.     

Glass formation and optical band gap studies on Bi<Subscript>2</Subscript>O<Subscript>3</Subscript>-B<Subscript>2</Subscript>O<Subscript>3</Subscript>-BaO ternary system

The glass forming region of Bi₂O₃-B₂O₃-BaO ternary system was investigated. A serial of glass samples with high Bi₂O₃ content in Bi₂O₃-B₂O₃-BaO system were prepared by using conventional melting and quenching meld, and the refractive indexes and absorption spectra of samples were measured. It is found that the refractive index of samples as well as the UV absorption increase with the increase of BaO content. According to the Tauc law, optical band gap E _opg which is assumed to be the effective energy band gap E _g is calculated and decreases with the increasing BaO content, and the ratio of E _g/E _opg is 1.3.     

Dielectric Properties of B2O3 Doped MgTiO3-CaTiO3 System Ceramics

The dielectric ceramics with a main crystal phase of MGTiO3 and additional crystal phase of CaTiO3 were prepared by the conventional electronic ceramics technology .the strucures of MgTiO3 are ilmenitetype,and belong to hexagonal syngony.the ratio of MgTiO3 to Ca TiO3 doping on the dielectric properties of MGTiO3-CaTiO3(MCT)ceranics were inrestigated.the addition of B2O3 decreases the sintering temperatnre and results in rapid desification without obrious negative effect on the Q values of the system(Q=1/tan ).B2O3 exists as liquid phase in the sintering process,promoting the reactions as a singering agent.     

Effect of aluminum addition on microstructure and properties of SiO<Subscript>2</Subscript>-B<Subscript>2</Subscript>O<Subscript>3</Subscript>-Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-CaO vitrified bond

Influence of aluminum addition on the structures and properties of SiO₂-B₂O₃-Al₂O₃-CaO vitrified bond at low sintering temperature and high strength was discussed. FTIR and XRD analyses were used to characterize the structures of the basic vitrified bond with different contents of aluminum. The bending strength and the thermal expansion coefficients were also tested. Meanwhile, the microstructures of composite specimens at sintering temperature of 660 °C were observed by scanning electron microscope (SEM). The experimental results showed that the properties of vitrified bond with 1wt% aluminum were improved significantly, where the bending strength, Rockwell hardness, and thermal expansion coefficient of the vitrified bond reached 132 MPa, 63 HRB, and 6.73×10^-6 °C^-1, respectively.     

Preparation,structure and dielectric properties of tungsten bronze ferroelectrics in SrO-Eu<Subscript>2</Subscript>O<Subscript>3</Subscript>-TiO<Subscript>2</Subscript>-Nb<Subscript>2</Subscript>O<Subscript>5</Subscript> system

Compounds Sr4Eu2Ti4Nb6O30 and Sr5EuTi3Nb7O30 with filled tetragonal tungsten bronze structure were prepared,and the dielectric characteristics and ferroelectric transition were investigated.Both ceramics displayed weak frequency dependence in room temperature dielectric constant,which decreased from 125 to 118 for Sr4Eu2Ti4Nb6O30,from 206 to 195 for Sr5EuTi3Nb7O30 in the frequency range of 10 kHz to 1 MHz.The present ceramics showed a diffuse ferroelectric phase transition.The frequency independent transition temperature (Tm) indicated the above compounds had no relaxor property.The diffuseness (γ) was 1.45 and 1.64 for Sr4Eu2Ti4Nb6O30 and Sr5EuTi3Nb7O30 respectively.The weak ferroelectric of the present materials are indicated from the P-E hysteresis loops,and a small 2Pr of 0.596 μC/cm2 and 0.068 μC/cm2 were observed for Sr4Eu2Ti4Nb6O30 and Sr5EuTi3Nb7O30 respectively.     

Molten Salt Synthesis of Ba（ Mgl／3Nb2／3 ）O3 Powder

The single-phrase Ba(Mgl/3Nb2/3)O3(BMN) powder was saccessfully prepared by the KCImolten salt synthesis(MSS) method. The temperature for single-phase BMN powders by MSS was about 400℃ lower than that by the solid-phase method. The average particle size (APS) was about 0.91,u.m at 900℃ and increased with increasing synhesis temperature. Based on the APS, the activation energy for particle growth in theMSS, whose value was 64. 1kJmol^-1.was attained. The sinterability of the powder prepared by MSS method wasbetter than that pretared by solid-phase method.     

The influence of mo additive on the microstructure and property of Ti/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> composite

The influence of Mo on the microstructure, bending strength and HV of Ti/Al₂O₃ composite was studied, and the influence mechanism was analyzed. The results indicate that after the addition of Mo, the composite organization is finer and phases distribution is better-proportioned which make the microstructure denser, the bending strength and HV of composite are also increased to a degree. But the bending strength increases first then decreases with the increasing of Mo content, so the appropriate Mo content for the Ti/Al₂O₃ composite is to be further confirmed. WANG Zhi: Born in 1962 Funded by Natural Science Foundation of China (No. 50232020) and Natural Science Foundation of Shandong Province (No. 2002F21)     

Fabrication of homogenous dispersion TiB<Subscript>2</Subscript>-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> composites

In order to get a homogenous mixture and compact of TiB2-Al2O3, hybridization as a surface modification method was used to prepare nano-scale Al2O3 coated TiB2 particles. PE-wax particles were first coated onto TiB2 particles by hybridization, and then the nano-scale Al2O3 particles were coated onto the surface of TiB2 coated by PE-wax particles again. SEM, TEM and EDS were used to characterize the microstructure of as-received core/shell particles and its compacts. The experimental results show that a particle-scale homogenous dispersion of TiB2 and Al2O3 can be formed not only in mixed powder but also in dewaxed compacts. The compacts then were sintered by gas-pressing sintering (GPS). Finial products show improved mechanic properties comparing with reference samples fabricated by normal ways.     

Microwave sintering of Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-ZrO<Subscript>2</Subscript>-WC-Co cermets

Composite powders of nanocrystalline WC-10Co (15wt%),Y2O3 (8mol%) stabilized nanocrystalline ZrO2 (30wt%),industrial cobalt powder (4.5wt%) and submicron Al2O3 (55wt%) composite powders were fabricated by high-energy ball-milling process.The nanocomposite powders were consolidated by microwave sintering process at temperature ranged 1300℃-1550℃ for 15min,respectively.The optimum consolidation conditions,such as temperature,were researched during microwave sintering process.Vickers Hardness of the consolidated cermets was measured by using a Vickers indentation test,and density of specimens was also determined by Archimedes’ principle.Microwave sintering process could not only increase the density of Al2O3-ZrO2-WC-Co cermets and reduce the porosity,but also inhibit abnormal grain growth.     

Electrochemical preparation of V<Subscript>2</Subscript>O<Subscript>3</Subscript> from NaVO<Subscript>3</Subscript> and its reduction mechanism

Vanadium trioxide (V₂O₃) was directly prepared by NaVO₃ electrolysis in NaCl molten salts. Electrolysis products were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS). The existing state and electrochemical behavior of NaVO₃ were also studied. The results indicated that V₂O₃ can be obtained from NaVO₃. VC and C were also formed at high cell voltage, high temperature, and long electrolysis time. During electrolysis, NaVO₃ was dissociated to Na⁺ and VO₃ ^? in NaCl molten salt. NaVO₃ was initially electro- reduced to V₂O₃ on cathode and Na₂O was released simultaneously. Na₂CO₃ was formed due to the reaction between Na₂O and CO₂. The production of C was ascribed to the electro-reduction of CO₃ ^2?. VC was produced due to the reaction between C and V₂O₃.     

Optical waveguide and nonlinear properties of Bi<Subscript>3</Subscript>NdTi<Subscript>3</Subscript>O<Subscript>12</Subscript> thin films

Neodymium-substituted bismuth titanate (Bi₃NdTi₃O₁₂, BNT) thin films were prepared on quartz substrates by a metal-organic solution deposition process. The crystalline structure was evaluated by X-ray diffraction. Waveguide property was investigated by using prism coupling technique and optical transmittance measurement. The optical nonlinearities of the film were measured by the top-hat Z-scan techniques and a large positive nonlinear refractive index, nonlinear refractive coefficient and two-photon absorption coefficient were determined to be 3.84 × 10⁻⁷ esu, 0.7523 cm²/GW and 4.81 × 10⁴ cm/GW, respectively. These results reveal that the BNT film may be a kind of new multifunctional materials.     

Surface organic modification of Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> magnetic nanoparticles

The surface organic modification of Fe3O4 nanoparticles with silane coupling reagent KH570 was studied. The modified and unmodified nanoparticles were characterized by FT-IR, XPS and TEM. The spectra of FT-IR and XPS revealed that KH570 was coated onto the surface of Fe3O4 nanoparticles to get Fe-O- Si bond and an organic coating layer also was formed. Fe3O4 nanoparticles were spheres partly with mean size of 18,8 nm studied by TEM, which was consistent with the result 17.9 nm calculated by Scherrer＇s equation. KH570 was adsorbed on surface and formed chemistry bond to be steric hindrance repulsion which prevented nanoparticles from reuniting. Then glycol-based Fe3O4 magnetic liquids dispersed stably was gained.     

Structure and properties of Mg-doped SrBi<Subscript>4</Subscript>Ti<Subscript>4</Subscript>O<Subscript>15</Subscript> Bi-layered compounds

The structure and properties of Mg-doped SrBi4Ti4O15（SBT） were dicussed. Mg substitution into SBT had two possibilities states with the dopant amount variety. Mg cation substituted mostly into Sr^2＋ and the amount proportion was 68.11%.Mg ion will substitute into Ti ion site in perovskite layer when the doping amount increases. Polarization increases sharply when x=0.1 and then decreases becauses of the domain pinning. The Curie temperature of Mg-doped SBT is about 300 ℃ and there is a broad diffuse phase transition near Tc with a flat peak near the Ta of SBT.     

Optical and magnetic properties of Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>/SiO<Subscript>2</Subscript> nano-composite films

Fe₂O₃/SiO₂ nano-composite films were prepared by sol-gel technique combining heat treatment in the range of 100–900 °C. The particle size was observed by FE-SEM. Optical properties of the films were investigated by UV-visible spectra. Structural and magnetic characteristics were investigated through FT-IR and VSM. The transparency of the Fe₂O₃/SiO₂ nano-composite films decreased with the content of the Fe₂O₃. Water and organic solvent in the films were evaporated with heat treatment, so the transparency of the films was enhanced under high temperature. It is also found that the saturation magnetization (M _s) of the films increases with the temperature. As the content of the Fe₂O₃ increases, when the content of the Fe₂O₃ is around 30wt%, the M _s of the films has a maximum value.