Crystallization and luminescence properties of Sm<Superscript>3+</Superscript>-doped SrO-Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-SiO<Subscript>2</Subscript> glass-ceramics

The Sm³⁺-doped SrO-Al₂O₃-SiO₂ (SAS) glass-ceramics with excellent luminescence properties were prepared by batch melting and heat treatment. The crystallization behavior and luminescent properties of the glass-ceramics were investigated by DTA, XRD, SEM and luminescence spectroscopy. The results indicate that the crystal phase precipitated in this system is monocelsian (SrAl₂Si₂O₈) and with the increase of nucleation/crystallization temperature, the crystallite increases from 66 % to 79 %. The Sm³⁺-doped SAS glass-ceramics emit green, orange and red lights centered at 565, 605, 650 and 715 nm under the excitation of 475 nm blue light which can be assigned to the ⁴G_5/2→⁶ H _j/2 (j=5, 7, 9, 11) transitions of Sm³⁺, respectively. Besides, by increasing the crystallization temperature or the concentration of Sm³⁺, the emission lights of the samples located at 565, 605 and 650 nm are intensified significantly. The present results demonstrate that the Sm³⁺-doped SAS glass-ceramics are promising luminescence materials for white LED devices by fine controlling and combining of these three green, orange and red lights in appropriate proportion.     

Direct synthesis of Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-modified Li(Ni<Subscript>0.5</Subscript>Co<Subscript>0.2</Subscript>Mn<Subscript>0.3</Subscript>)O<Subscript>2</Subscript> cathode materials for lithium ion batteries

To improve the cyclic stability at high temperature and thermal stability, the spherical Al₂O₃-modified Li(Ni_0.5Co_0.2Mn_0.3)O₂ was synthesized by a modified co-precipitation method, and the physical and electrochemical properties were studied. The TEM images showed that Li(Ni_0.5Co_0.2Mn_0.3)O₂ was modified successfully with nano-Al₂O₃. The discharge capacity retention of Al₂O₃-modified Li(Ni_0.5Co_0.2Mn_0.3)O₂ maintained about 99% after 200 cycles at high temperature (55 °C), while that of the bare one was only 86%. Also, unlike bare Li(Ni_0.5Co_0.2Mn_0.3)O₂, the Al₂O₃-modified material cathode exhibited good thermal stability.     

Phase transition and photoluminescence properties of Eu<Superscript>3+</Superscript>-doped ZnMoO<Subscript>4</Subscript> red phosphors

Eu³⁺-doped ZnMoO₄ with different doping concentrations were synthesized by a hydrothermal method. The effects of Eu³⁺ doping on the phase structure and photoluminescence (PL) properties of ZnMoO₄ were investigated. The result showed that the introduction of Eu3+ could lead to phase transition of ZnMoO₄. With the increase of Eu³⁺ doping amount, β-ZnMoO₄ was transformed to α phase gradually, which led to different photoluminescence performances. The optimized doping concentration of Eu³⁺ was 6 mol% for the highest emission intensity at 615 nm. Its CIE chromaticity coordinates were (0.667, 0.331), which were very close to the values of standard chromaticity (0.67, 0.33) for National Television Standards Committee (NTSC) system. Therefore, Eu³⁺-doped ZnMoO₄ is considered to be a promising red-emitting phosphor for white LED applications.     

Synthesis and photocatalytic property of the ZrO<Subscript>2</Subscript>/TiO<Subscript>2</Subscript> pillared laponite

The ZrO2/TiO2 pillared laponite (Ti-Zr-lap) photocatalysts were prepared with intercalation reaction by supercritical fluid drying (SCFD),and characterized by XRD,TEM,SEM and BET surface area analysis,and the photocatalytic properties of Ti-Zr-lap were investigated by degradation of azo dye acid red B (ARB).The results showed that the ZrO2/TiO2 pillared structures in laponite could be formed,with the mass fraction of (Zr4++Ti4+)/laponite (Xm) increasing,the basal spacing and the BET surface area of Ti-Zr-lap significantly increased.The Ti-Zr-lap used as photocatalyst had the advantages of stable and porous layered structure,large surface area with the anatase type TiO2.Compared with the Ti-Zr-lap dried by air drying,the Ti-Zr-lap dried by SCFD showed better photocatalytic property which was very close to that of P25 TiO2.Using the Ti-Zr-lap as photocatalyst with the optimum Xm of 0.16 and the calcination temperature of 500 ℃,under the conditions of the initial concentration of ARB 20 mg/L,photocatalyst concentration of 1.5 g/L and irradiation time 60 min,the decoloring rate of ARB could achieve 98.3%,indicating that the Ti-Zr-lap had excellent photocatalytic property.     

Interaction of rare earth ions in Sr<Subscript>2</Subscript>MgSi<Subscript>2</Subscript>O<Subscript>7</Subscript>: Eu<Superscript>2+</Superscript>, Dy<Superscript>3+</Superscript> material

To discuss the function of Eu and Dy and their interaction in Sr₂MgSi₂O₇: Eu²⁺, Dy³⁺ long afterglow material, the Eu and Dy single doped and their co-doped Sr₂MgSi₂O₇: Eu²⁺, Dy³⁺ were prepared. The samples were characterized by X-ray diffraction (XRD), decay curves, photoluminescence (PL), and thermoluminescence (TL). The results indicate that Sr₂MgSi₂O₇: Eu has afterglow properties, and the doping of Eu ion in Sr₂MgSi₂O₇: Eu²⁺, Dy³⁺ can lower the depth of traps. Eu ion can not only serve as luminescence center, but also produce traps in the matrix, meanwhile, it also exerts certain influences on the traps produced by Dy in Sr₂MgSi₂O₇: Eu²⁺, Dy³⁺. The Dy ion can not act as luminescence center but relates to the change of the traps in the Sr₂MgSi₂O₇ matrix.     

Preparation and Performance of Si<Superscript>4+</Superscript>-doping Rod-shaped TiO<Subscript>2</Subscript> Powder by Nonhydrolytic Sol-gel Method

Titania (TiO₂) nanorod powder was prepared by nonhydrolytic sol-gel method using titanic chloride (TiCl₄) as titanium source, methylene dichloride (CH₂Cl₂) as solvent, absolute ethyl alcohol (CH₃CH₂OH) as oxygen donor. The effects of Si⁴⁺ doping on the TiO₂ nanocrystalline phase transformation temperature were systematically researched. The results showed that when the molar ratio of Ti⁴⁺ to Si⁴⁺ is 1 to1.3, TiO₂ prepared by calcination at 1100 °C for 1 hour exhibits rod shape and has good photocatalytic activity. Doping of Si⁴⁺ makes glass phase core-shell structure forming on the surface of anatase crystal particles, which can inhibit crystal phase transformation and raise the transformation temperature, making TiO₂ stable in anatase phase at 1200 °C.     

Phase structure and electrical properties of La<Subscript>2</Subscript>O<Subscript>3</Subscript>-doped BiInO<Subscript>3</Subscript>-PbTiO<Subscript>3</Subscript> ceramics with high curie temperature

The phase structure and electrical properties of pure and La2O3-doped Bi-InO3-PbTiO3 （BI-PT） ceramics were studied respectively. In （1 -x）BI-xPT （x=0.72-0.80） ceramics, the stability of tetragonal phase increased with increasing x, and pure perovskite structure was obtained for x=-0.80 ceramics. The phase transition temperature range was between 575 ℃ and 600 ℃ for x=0.72-0.80 ceramics, higher than that of PT （-490 ℃）. The c/a ratio almost linearly decreased with increasing La2O3 content in x-0.80 ceramics. It is believed that Pb^2＋ vacancies were formed by La^3＋ substituting Pb^2＋ in La2O3-doped BI-PT ceramics. Tc shifted to lower temperature by 30 ℃/mol% La2O3. The maximum dielectric constant 8557 around 559 ℃ was exhibited in 0.5mol%-doped BI-0.80PT ceramics. La2O3-doped ceramics could be poled resulting from decreasing of c/a ratio and improving of dielectric loss and resistivity. The maximum piezoelectric coefficient d33 was 12 pC/N for 2mol%-doped BI-0.80PT ceramics.     

Fe<Subscript>3</Subscript>O<Subscript>4</Subscript>@PAM@NTA-Ni<Superscript>2+</Superscript> Magnetic Composite Nanoparticles for Highly Specific Separation of His-tagged Proteins

A facile approach has been developed to synthesize Fe₃O₄@PAM (polyacrylamide) nanoparticles (NPs) with carboxyl groups on the surfaces by copolymerization with acrylamide and acrylic acid in Fe₃O₄ NPs aqueous suspension. Nitrilotriacetic acid (NTA) was conjugated to the magnetic NPs via well-known carboniimide chemistry using EDC and NHS. The Ni²⁺ ions loaded on the surface of NPs provide abundant docking sites for immobilization of His-tagged green fluorescent proteins (His-tagged GFP). The high magnetic property of Fe₃O₄@PAM@NTA-Ni²⁺ allows an easy separation of the NPs from solution under an external magnetic field, with high His-tagged protein binding capacity (42 μg protein/mg of NPs). The NPs can be recycled for at least four times without significant loss of binding capacity to proteins. These materials show great potential to separate His-tagged protein with low-cost purification at industrial scale.     

Preparation and Upeonversion Lumineseenee ofNanoerystailine Gd2O3： Er^3＋, Yb^3＋

Nanocrystalline Gd1.77Yb0.2Er0.03O3 samples were prepared by combustion and precipitation methods. Structures and upconversion luminescence properties of samples were studied. The results of XRD show that all samples are cubic structure, the average crystallite size could be calculated as 23 nm and 39 nm, respectively. The lattice constants were obtained. The FT-IR spectra were measured to investigate the vibrational feature of the samples. Upconversion luminescence spectra of samples under 980 nm laser excitation were investigated. The strong red emission of samples were observed, and attributed to 4F9/2→4I152 transitions of Er^3＋ ions, the emission intensity for sample synthesized by precipitation method is stronger compared to that of combustion method. The possible upconversion luminescence mechanisms in nanocrystalline Gd1.77Yb0.2Er0.03O3 were discussed.     

Fluorescence detection for H<Subscript>2</Subscript>PO<Subscript>4</Subscript><Superscript>-</Superscript> based on carbon dots/Fe<Superscript>3+</Superscript> composite

A novel fluorescent probe for H₂PO₄ ^- was designed and fabricated based on the carbon dots/Fe³⁺ composite. The carbon dots were synthesized by an established one-pot hydrothermal method and characterized by transmission electron microscope, X-ray diffractometer, UV-Vis absorption spectrometer and fluorescence spectrophotometer. The carbon dots/Fe³⁺ composite was obtained by aqueous mixing of carbon dots and FeCl₃, and its fluorescence property was characterized by fluorescence spectrophotometer. The fluorescence of carbon dots was quenched by aqueous Fe³⁺ cations, resulting in the low fluorescence intensity of the carbon dots/Fe³⁺ composite. On the other hand, H₂PO₄ ^- reduced the concentration of Fe³⁺ by chemical reaction and enhanced the fluorescence of the carbon dots/Fe³⁺ composite. The Stern-Volmer equation was introduced to describe the relation between the relative fluorescence intensity of the carbon dots/Fe³⁺ composite and the concentration of H₂PO₄ ^-, and a fine linearity (R ²=0.997) was found in the range of H₂PO₄ ^- concentration of 0.4-12 mM.     

Synthesis and luminescence of nano fluorescent powder of Y<Subscript>4</Subscript>Al<Subscript>2</Subscript>O<Subscript>9</Subscript>: Eu<Superscript>3+</Superscript>

Nano fluorescent powder of Y₄Al₂O₉: Eu³⁺ was synthesized by sol-gel method. The XRD shows that the product prepared at 900°C is pure-phase Y₄Al₂O₉: Eu³⁺. The Y₄Al₂O₉ powder is nano-size crystal testified by BF and ED analysis of TEM. The grain diameter of Y₄Al₂O₉ is in the range between 20 and 50nm, and its average is 30 nm. The luminescent spectra show that Eu³⁺ ious occupy two kinds of sites in Y₄Al₂O₉ crystal lattice. One is in the strict inversion center, and the other is in off lying inversion center. When excited with UV light (λ=254nm), Y₄Al₂O₉: Eu³⁺ exhibits an orange emission bond at λ=590 nm due to the⁵D_o→⁷F₁ transition and a red emission band at λ=610 nm due to⁵D_o→⁷F₂ transition. YUAN Xi-ming: Born in 1951 Funded by Key Scientific and Technological Project of Hubei Province (2001 AA102A03)     

Preparation and optical properties of Er<Superscript>3+</Superscript>: Na<Subscript>2</Subscript>O-Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-SiO<Subscript>2</Subscript> transparent glass-ceramics

Na₂O-Al₂O₃-SiO₂ glass-ceramics doped with Er³⁺ ions were synthesized by the conventional melt quenching technique at a low melting temperature. The samples were characterized by differential scanning calorimetry (DSC), X-ray diffraction (XRD), scanning electron microscopy (SEM), UV-vis-NIR scanning spectrophotometry, and fluorescence spectrometry. The results show that the main crystalline phase of glass-ceramics is nepheline.The best heat-treatment process is at 520 °C for 2 h. Because the up-conversion luminescence and near infrared luminescence properties of glass doped with Eu³⁺ are studied in detail.     

Roles of Eu^2＋, Dy^3＋ Ions in Persistent Luminescence of Strontium Aluminates Phosphors

The polycrystalline Eu^2＋ and Dy ^3＋ co-doped strontium aluminates SrAl2O4： Eu^2＋, Dy^3＋ with different compositions were prepared by solid state reactions. The UV-excited photoluminescence, persistent luminescence and thermo-luminescence were studied and compared. Results show that the doped Eu^2＋ ion in SrAl2O4： Eu^2＋, Dy^3＋ phosphors works as not only the UV-excited luminescent center but also the persistent luminescent center. The doped Dy^3＋ ion can hardly yield any luminescence under UV-excitation, but effectively enhance the persistent luminescence and thermo-luminescence of SrAl2O4： Eu^2＋. Dy^3＋ co-doping can help form electron traps with appropriate depth due to its suitable electro-negativity, and increase the density and depth of electron traps. Based on above observations, a persistent luminescence mechanism, electron transfer model, is proposed and illustrated.     

Influence of rare earth co-dopant on the photocatalytic property of TiO<Subscript>2</Subscript> nano-particles

A series of nanometer TiO2 photocatalysts co-doped respectively with rare earth Er3+-Ce3+ and La3+-Fe3+ were prepared by sol-gel method,and the photocatalytic activity under ultra-violet light was evaluated by photocatalytic degradation of methyl blue.The crystallographic forms,particles size,and morphology were characterized by XRD and TEM.The results showed that the optimum heat temperature of co-doped TiO2 was 550 ℃,and the co-doped TiO2 kept anatase.The anatase crystal had the average size of 20 nm.The ...     

Preparation of nanometer Nd<Superscript>3+</Superscript>, Y<Superscript>3+</Superscript> co-doped CaF<Subscript>2</Subscript> powder by coprecipitation-azeotropic distillation technique

The synthesis of Nd³⁺, Y³⁺:CaF₂ nanopowder was conducted by azeotropic distillation method, which effectively dehydrated hydrous CaF₂ and prevented forming hard agglomerates. X-ray diffraction (XRD), scanning electron microscopy (SEM), scanning calorimetries-thermalgravimetry (DSC-TG), Fourier transform infrared spectroscopy (FT-IR) and absorption spectroscopy were performed to characterize the powder properties. The experimental results showed that products obtained by azeotropic distillation were single phased, rather monodispersed, successfully prevented the hard agglomerate formation and effectively removed the residual water inside the as-prepared precipitate than that of the direct drying. The absorption spectra showed a wider and stronger absorption bands around 792 nm, which should be profitable for LD pumping.     

Preparation and characterization of CeO<Subscript>2</Subscript>-TiO<Subscript>2</Subscript>/SnO<Subscript>2</Subscript>:Sb films deposited on glass substrates by R.F. sputtering

CeO2-TiO2 films and CeO2-TiO/SnO2：Sb （6 mol%） double films were deposited on glass substrates by radio-frequency magnetron sputtering （R.F. Sputtering）, using SnO2：Sb（6 mol%） target, and CeO2- TiO2 targets with different molar ratio of CeO2 to TiO2 （CeO2：TiO2-0：1.0; 0.1：0.9; 0.2：0.8; 0.3：0.7; 0.4：0.6; 0.5：0.5; 0.6：0.4; 0.7：0.3; 0.8：0.2; 0.9：0.1; 1.0：0）. The films are characterized by UV-visible transmission and infrared reflection spectra, scanning electron microscopy （SEM）, Raman spectroscopy, X-ray photoelectron spectroscopy （XPS） and X-ray diffraction （XRD）, respectively. The obtained results show that the amorphous phases composed of CeO2-TiO2 play an important role in absorbing UV, there are Ce^3-, Ce^4- and Ti^4- on the surface of the films; the glass substrates coated with CeO2-TiO2 （Ce/Ti=0.5：0.5; 0.6：0.4）/SnO2：Sb（6 mol%） double films show high absorbing UV（〉99）, high visible light transmission （75%） and good infrared reflection （〉70%）. The sheet resistance of the films is 30-50 Ω/□. The glass substrates coated with the double functional films can be used as window glass of buildings, automobile and so on.     

Biomolecule-assisted solvothermal synthesis and enhanced visible light photocatalytic performance of Bi<Subscript>2</Subscript>S<Subscript>3</Subscript>/BiOCl composites

Novel Bi₂S₃/BiOCl photocatalysts were successfully synthesized via a facile biomolecule-assisted solvothermal method and biomolecule L-cysteine was used as the sulfur source. The structures, morphology, and optical properties of the synthesized samples were characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), Raman spectroscopy, transmission electron microscopy (TEM), and UV-vis diffuse reflectance spectroscopy (DRS). The presence of Bi₂S₃ in the Bi₂S₃/BiOCl composites could not only improve the optical properties but also enhance the photocatalytic activities for the degradation of Rhodamine B (RhB) under visible-light irradiation (λ > 420 nm) as compared with single Bi₂S₃ and BiOCl. Especially, the sample displayed the best performance of the photodegradation when the feed molar ratio of BiCl3 and L-cysteine was 2.4:1, which was about 10 times greater than that of pure BiOCl. The enhanced photocatalytic activities could be ascribed to the effective separation of photoinduced electrons and holes and the photosensitization of dye. Moreover, the possible photodegradation mechanism was also proposed, and the results revealed that the active holes (h⁺) and superoxide radicals (?O₂ ^?) were the main reactive species during photocatalytic degradation.     

Microstructures and fatigue-free properties of the La<Superscript>3+</Superscript> and Nd<Superscript>3+</Superscript> doped Bi<Subscript>4</Subscript>Ti<Subscript>3</Subscript>O<Subscript>12</Subscript> thin films prepared by modified sol-gel technique

Ferroelectric Bi_3.25La_0.75Ti₃O₁₂ (BLT) and Bi_3.15Nd_0.85Ti₃O₁₂ (BNT) thin films were fabricated on Pt/TiO₂/SiO₂/Si (100) substrates by a modified sol-gel technique. X-ray diffraction indicated that these films were of single phase with random polycrystalline orientations. The surface morphologies of the films were observed by scanning electron microscope, showing uniform, dense films with grain size of 50–100 nm. Well-saturated hysteresis loops of the films were obtained in metal-ferroelectric-metal type capacitors with Cu top electrodes at an applied voltage of 400 kV/cm, giving the remanent polarization (2P _r) and coercive field (2E _c) values of the films of 25.1 μC/cm² and 203 kV/cm for BLT, and 44.2 μC/cm² and 296 kV/cm for BNT, respectively. Moreover, these capacitors did not show fatigue behaviors after up to 1.75×10¹⁰ switching cycles at the test frequency of 1 MHz, suggesting a fatigue-free character. The influences of the La³⁺ and Nd³⁺ doping on the properties of the films were comparatively discussed. Supported by the National Key Basic Research and Development Program of China (Grant No. 2006CB932305) and the Natural Science Foundation of Hubei Province, China (Grant No. 2004ABA082)     

Optimized photoluminescence of red phosphor K<Subscript>2</Subscript>LiAlF<Subscript>6</Subscript>:Mn<Superscript>4+</Superscript> synthesized by a cation-exchange method

Red phosphor K₂LiAlF₆:Mn⁴⁺ has been synthesized by a cation-exchange method in HF solution. To optimize their optical properties, phosphors were synthesized using different reaction conditions. The K₂LiAlF₆:0.5%Mn⁴⁺ synthesized at 20°C for 4 h shows the highest luminescence intensity. The temperature-dependent emission intensity of the phosphor was investigated, and it was found to exhibit good thermal stability, making it a promising red phosphor candidate for warm WLEDs.     

Thermoelectric Properties and Electronic Structure of Ca3Co2O6

The nanosized Ca3Co2O6 powder was synthesized via sol-gel process.The phase composition was characterized by means of X-ray diffraction.Polycfrystalline swnples of Ca3Co2O6 were prepared by a sintering procedure of nanosized power.The seebeck cofficient and electrical conductivity of the samples were measured from 450K up to 750 K.The results show that the Seebeck coefficient increases with the increasing temperature.The electronic structures were calculated using the self-cwtsistent full-potential linearized augmentedc plane-wave (LAPW) method within the density functional theory.The relationship between thermoelectric property and electronic structures was discussed.