Morphology study of oriented SmBCO film deposited by MOCVD

c-axis-oriented SmBa_2Cu_3O_7(SmBCO) films have been deposited on(100)- LaA1O_3(LAO)substrate by metal organic chemical vapor deposition(MOCVD) technique.The effects of deposition temperature(T_(dep)) and total pressure(P_(tot)) on the orientation and microstructure of SmBCO films were investigated.The orientation of SmBCO films transformed from α-axis to c-axis with increasing of T_(dep) from 900 to 1 100℃.At T_(dep)=1 050℃,SmBCO films had c-axis orientation and tetragon surface.At P_(tot)~(dep)=400-800 Pa and T_(dep)=1 050 ℃,totally c-axis-oriented SmBCO films were obtained.The R_(dep) of SmBCO films increased firstly and then decreased with increasing P_(tot).The surface of SmBCO films exhibited tetragon morphology at 1 050 ℃ and400 Pa.Maximum thickness of SmBCO film deposited was 1.2μm at P_(tot)= 600 Pa,and the corresponding R_(dep)was 7.2 μm·h~(-1).     

Elimination of Voids at Interface of <Emphasis Type="Italic">β</Emphasis>-SiC Films and Si Substrate by Laser CVD

Void-free β-SiC films were deposited on Si(001) substrates by laser chemical vapor deposition using hexamethyldisilane (HMDS) as the precursor. The effect of the time of introducing HMDS, i e, the substrate temperature when HMDS introduced (T_in), on the preferred orientation, surface microstructure and void was investigated. The orientation of the deposited SiC films changed from <001> to random to <111> with increasing T_in. The surface showed a layer-by-layer microstructure with voids above T_in ? 773 K, and then transformed into mosaic structure without voids at T_in= 298 K. The mechanism of the elimination of voids was discussed. At T_in =298 K, Si surface can be covered by an ultrathin SiC film, which inhibits the out-diffusion of Si atoms from substrate and prohibites the formation of the voids.     

Effect of Al in slag blended cement paste under sulfate attack

Unilateral sulfate attack of cementitious materials containing 40% slag with different water to binder ratios was investigated. The results showed that the degradation of slag blended cement pastes was nearly from the corners of paste surface with cracking and spallings, water-to-binder(w/b) ratio made a significant sense to the damage that low w/b ratio led to little weight loss, less cracking and spalling damage and vice versa. Microstructural experimental results demonstrated that in the three different stages of sulfate attack, degradation of pastes was primarily associated with the migration behavior and bonding configuration of aluminum, in the early ages Al was mostly present in C-(A)-S-H, and thus, the damage of pastes hardly appeared while at later ones Al had been largely transferred from C-(A)-S-H into AFt, leading to expansive damage.     

YIG thin film for RF integrated inductor

The yttrium iron garnet(YIG) thin films prepared by the sol-gel method and rapid thermal annealing(RTA) process for integrated inductor are investigated. The X-ray diffraction(XRD) results indicate that the YIG film annealed above 650 ℃ is poly-crystalline with single-phase garnet structure. Moreover, it can be found that the initial permeability μi, saturation magnetization M_S and coercivity H_c of these YIG films increase with increasing RTA temperature. Low temperature annealing after crystallization can further improve the magnetic properties of YIG film. Thereby, a planar integrated inductor in the presence of Si substrate/SiO_2 layer/Y_(2.8)Bi_(0.2)Fe_5O_(12) thin film/Cu spiral coil structure is fabricated successfully by the standard IC processes. Due to the magnetic enhancement originated from YIG film, the inductance L and quality factor Q of the inductor with YIG film are improved in a certain frequency range.     

Synthesis and characterization of triangular-pyramidal bismuth oxide via a one-step chemical precipitation route

Triangular-pyramidal ω-Bi_2O_3 is successfully synthesized via a one-step wet-chemical method.XRD,SEM,and UV-vis have been employed to characterize the as-prepared samples.Structural characterization by XRD confirms the formation of triclinic ω-Bi_2O_3 with high purity.The well-defined flowerlike Bi_2O_3 structures consisted of many triangular-pyramids are formed.Preparative parameters,such as concentration of PEG 6000,have great effects on the morphology and the particle size.The obvious absorption edge for ω-Bi_2O_3 powder is located at about 493 nm,which corresponds to the optical band gap energy of2.73 eV.     

Effects of annealing processes on Cu<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>Si<Subscript>1-<Emphasis Type="Italic">x</Emphasis></Subscript> thin films

The Cu _x Si_1-x thin films have been grown by pulsed laser deposition (PLD) with in situ annealing on Si (001) and Si (111), respectively. The transformation of phase was detected by X-ray diffraction (XRD). The results showed that the as-deposited films were composed of Cu on both Si (001) and Si (111). The annealed thin films consisted of Cu + η”-Cu₃Si on Si (001) while Cu + η’-Cu₃Si on Si (111), respectively, at annealed temperature (T _a) = 300-600 °C. With the further increasing of T _a, at T _a= 700 °C, there was only one main phase, η”-Cu₃Si on Si (001) while η’-Cu₃Si on Si (111), respectively. The annealed thin films transformed from continuous dense structure to scattered-grain morphology with increasing T _a detected by field emission scanning electron microscope (FESEM). It was also showed that the grain size would enlarge with increasing annealing time (t _a).     

Composition dependence of phase structure and electrical properties of (1−y)Bi1−xNdxFeO3−yBiScO3 ceramics

In this work, we have studied a new lead-free ceramic of(1-y)Bi_(1-x)Nd_xFeO_(3-y)BiScO_3(0.05≤x≤0.15 and 0.05≤y≤0.15) prepared by a conventional solid-state method, and the influences of Nd and Sc content on their phase structure and electrical properties were investigated in detail. The ceramics with 0.05≤x≤0.10 and 0.05≤y≤0.15 belong to an R3 c phase, and the rhombohedral-like and orthorhombic multiphase coexistence is established in the composition range of 0.125≤x≤0.15 and y=0. The electrical properties of the ceramics can be enhanced by modifying x and y values. The highest piezoelectric coefficient(d33~51 p C/N) is obtained in the ceramics with x=0.075 and y=0.125, which is superior to that of a pure BiFeO_3 ceramic. In addition, a lowest dielectric loss(tan δ~0.095%, f=100 k Hz) is shown in the ceramics with x=0.15 and y=0 due to the involvement of low defect concentrations, and the improved thermal stability of piezoelectricity at 20–600oC is possessed in the ceramics. We believe that the ceramics can play a meaningful role in the high-temperature lead-free piezoelectric applications.     

Effect of Cu-Ti-C reaction composition on reinforcing particles size of TiC<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>/Cu composites

TiC _x /Cu composites were fabricated by combustion synthesis and hot press technology. Using XRD, SEM, EDS, FESEM analysis methods, the effects of various carbon sources and different Cu contents on the microstructures of TiC _x /Cu composites and the size of TiC _x particles were investigated. Results showed that TiC _x reinforcing particles size increases with decreasing Cu content in Cu-Ti-C reaction system. With carbon nanotubes (carbon black) serving as carbon source, the generated TiC _x particles size transits from nanometer to submicron when Cu content corresponding to the reaction system is reduced to 60 vol% (70 vol%); while graphite serves as carbon source, there is no clear limiting concentration. C particles with smaller size, larger specific surface area and better distribution result in finer TiC _x particles, which is more beneficial to generating nano-sized TiC _x /Cu composites.     

Preparation and Properties of Sapphire by Edge-defined Film-fed Growth (EFG) Method with Different Growth Directions

Sapphire, belonging to hexagonal crystal system, is typically anisotropic which makes it direction-sensitive. To research the effects of growth directions on properties of sapphire, c-[0001] seed(c-sapphire) and a-[11-20] seed(a-sapphire) were used to prepare sapphire by edge-defined film-fed growth(EFG) method. The samples were analyzed through lattice integrity, dislocation and corrosion performance by double-crystal XRD, OM, AFM, SEM and EDX. It was shown that the lattice integrities of two growth-direction crystals were both well due to the small FWHM values. While the average densities of dislocation in c-sapphire and a-sapphire were 9.2×103 and 3.9×103 cm-2 respectively, the energy of dislocation in c-sapphire was lower than that in a-sapphire. During Strong Phosphoric Acid(SPA) etching, the surface of c-sapphire basically kept smooth but in a-sapphire there were many point-like corrosion pits where aluminum and oxygen atoms lost by 2:1. Our work means that it will be promising for growing c-[0001] seed sapphire by EFG if aided by parameter optimization.     

Reaction mechanism and microstructure evolution of reaction sintered <Emphasis Type="Italic">h</Emphasis>-BN

Hexagonal boron nitride ceramic (h-BN) based on the nitridation of B powders was obtained by reaction sintering method. The effects of sintering temperature on the mechanical properties and microstructure of the resultant products were investigated and the reaction mechanism was discussed. Results showed that the reaction between B and N₂ occurred vigorously at temperatures ranging from 1 000 °C to 1 300 °C, which resulted in the generation of t-BN. When the temperature exceeded 1 450 °C, transformation from t-BN to h-BN began to occur. As the sintering temperature increased, the spherical particles of t-BN gradually transformed into fine sheet particles of h-BN. These particles subsequently displayed a compact arrangement to achieve a more uniform microstructure, thereby increasing the strength.     

Synthesis and Photovoltaic Properties of A Dithieno[6,5-<Emphasis Type="Italic">b</Emphasis>:10,11-<Emphasis Type="Italic">b</Emphasis>′]-8H-Cyclopentyl[1,2-b:4,3-<Emphasis Type="Italic">b</Emphasis>′]Diphenanthrene based Donor-Acceptor Alternating Copolymer

A novel fused nonacyclic monomer of dithieno[6,5-b:10,11-b′]-8H-cyclopentyl[1,2-b:4,3-b′] diphenanthrene (DTCPDP) was synthesized by combining the structural features of ladder-type and multiple fused multi-cyclic aromatics. DTCPDP has a single sp3-hybridized carbon bridge between fused multi-cyclic aromatics. The copolymerization of DTCPDT with the electron accepting unit of 4,7-di(thiophen-2-yl)benzo[c][1,2,5]thiadiazole (DTBT) via Stille coupling afforded a novel donor-acceptor (D-A) alternating copolymer PDTCPDT-DTBT. The copolymer exhibited good chemical and thermal stabilities, with an optical band gap of 1.82 eV and a low-lying highest occupied molecular orbital (HOMO) energy level of -5.32 eV. When the copolymer was incorporated into polymer: fullerene (PC₇₁BM) blends to fabricate bulk heterojunction polymer solar cell devices, the devices exhibited a moderate maximum power conversion efficiency (PCE) of 5.90%.     

Density function theory study of electronic,optical and thermodynamic properties of CaN<Subscript>2</Subscript>, SrN<Subscript>2</Subscript> and BaN<Subscript>2</Subscript>

We put forward a first-principles density-functional theory about the impact of pressure on the structural and elastic properties of bulk CaN₂, SrN₂ and BaN₂. The ground state properties of three alkaline earth diazenides were obtained, and these were in good agreement with previous experimental and theoretical data. By using the quasi-harmonic Debye model, the thermodynamic properties including the debye temperature Θ _D, thermal expansion coefficient α, and grüneisen parameter γ are successfully obtained in the temperature range from 0 to 100 K and pressure range from 0 to 100 GPa, respectively. The optical properties including dielectric function ε(?), absorption coefficient α(?), reflectivity coefficient R(?), and refractive index n(?) are also calculated and analyzed.     

Rheological behaviors of fresh cement pastes with polycarboxylate superplasticizer

The rheologicalbehaviors of fresh cement paste with polycarboxylate superplasticizer were systematically investigated.Influentialfactors including superplasticizer to cement ratio(Sp/C),water to cement ratio(w/c),temperature,and time were discussed.Fresh cement pastes with Sp/Cs in the range of 0 to 2.0% and varied W/Cs from 0.25 to 0.5 were prepared and tested at 0,20 and 40 °C,respectively.Flowability and rheologicaltests on cement pastes were conducted to characterize the development of the rheologicalbehavior of fresh cement pastes over time.The exprimentalresults indicate that the initialflowability and flowability retention over shelf time increase with the growth in superplasticizer dosage due to the plasticizing effect and retardation effect of superplasticizer.Higher temperature usually leads to a sharper drop in initialflowability and flowability retention.However,for the cement paste with high Sp/C or w/c,the flowability is slightly affected by temperature.Yield stress and plastic viscosity show similar variation trends to the flowability under the abovementioned influentialfactors at low Sp/C.In the case of high Sp/C,yield stress and plastic viscosity start to decline over shelf time and the decreasing rate descends at elevated temperature.Moreover,two equations to roughly predict yield stress and plastic viscosity of the fresh cement pastes incorporating Sp/C,w/c,temperature and time are developed on the basis of the existing models,in which experimentalconstants can be extracted from a database created by the rheologicaltest results.     

Comparison of the influence factors on<Emphasis Type="Italic">NDVI</Emphasis> for CCD camera and WFI imager on CBERS-02

CCD and WFI are payloads in the visible light and near infrared bands on CBERS satellites and they have not been applied widely, especially WFI. This article mainly probes into the potential of these two sensors’ application in the vegetation monitoring and analyses the influences of radiometric calibration, atmosphere conditions and sun-observing geometry, etc. onNDVI obtained from these two sensors respectively. In addition it analyses the effect of the spectral response difference of red and near infrared spectral bands in CCD and WFI sensors onNDVI. Results indicate that radiometric calibration is the most important factor onNDVI, which cannot be applied to vegetation monitoring without radiometric calibration. Results also demonstrate that near surfaceNDVI is different greatly from that of TOA which change with atmosphere conditions. The study shows thatNDVI is also affected by the non-lambertian character of surface and the change of the atmospheric path with the observing geometry. AndNDVI of WFI is higher than that of CCD. They are very different because of their spectral diffirence, but they have a good linear relevant relationship.     

Hydration process and crack tendency of concrete based on resistivity and restrained shrinkage crack

Hydration process, crack potential and setting time of concrete grade C30, C40 and C50 were monitored by using a non-contact electrical resistivity apparatus, a novel plastic ring mould and penetration resistance methods, respectively. The results show the highest resistivity of C30 at the early stage until a point when C50 accelerated and overtook the others. It has been experimentally confirmed that the crossing point of C30 and C50 corresponds to the final setting time of C50. From resistivity derivative curve, four different stages were observed upon which the hydration process is classified; these are dissolution, induction, acceleration and deceleration periods. Consequently, restrained shrinkage crack and setting time results demonstrated that C50 set and cracked the earliest. The cracking time of all the samples occurred within a reasonable experimental period thus the novel plastic ring is a convenient method for predicting concrete’s crack potential. The highest inflection time (t _i) obtained from resistivity curve and the final setting time (t _f) were used with crack time (t _c) in coming up with mathematical models for the prediction of concrete’s cracking age for the range of concrete grade considered. Finally, an ANSYS numerical simulation supports the experimental findings in terms of the earliest crack age of C50 and the crack location.     

Effects of functionalized silica nanoparticles on characteristics of nanocomposites PES cation exchange membranes

Nanocomposite cation exchange membranes(CEMs) were prepared by adding various loadings of functionalized silica nanoparticles to the sulfonated polyethersulfone(s PES) polymeric matrix. The silica nanoparticles were functionalized by mercaptopropyl(F_1, IEC=0), propylsulfonic acid(F_2, IEC= 2.71), and sulfonic acid(F_3, IEC=2.84). The properties of prepared membranes were investigated by varying the loadings of functionalized silica nanoparticles. Applying functionalized nanoparticles provides additional ion exchange groups and enhances water contents as well as conductivities and permselectivities of the membranes. The maximum IEC of 1.9 meq.g~(-1) was obtained for the membrane having 3 wt% F_3 nanoparticles and the maximum conductivity of 0.237 S·cm~(-1) was achieved for the membrane having 2 wt% F_3 nanoparticles, which were 19.6% and 64% higher than the corresponding values for s PES membrane, respectively. The excellent properties of the nanocomposite cation-exchange membranes make them appropriate candidates for electrodialysis and desalination processes.     

Bimodal plate structures induced by pulsed laser in duplex-phase Zr alloy

A duplex-phase Zr-2.5Nb alloy was treated by pulsed laser, followed by careful microstructural characterization using field emission gun scanning electron microscope and attached electron backscatter diffraction. Beneath the modification zones with common uniform α-plate structures(UPS), a layer of unreported bimodal α-plate structures(BPS) featured by coarse(submicron)plates forming multiple cores surrounded by dense fine(nanoscale) plates was found. Presence of such BPS is attributed to non-equilibrium thermodynamic conditions induced by the pulsed laser treatments. Limited diffusion of Nb due to the short pulse during laser heating allows β phases with distinctly different Nb contents to be presented: Nb-enriched prior β films and Nb-depleted β phases, transforming into the fine and the coarse plates during cooling, respectively. Orientation analyses show that both types of plates in the BPS are aroused essentially from a single β orientation, suggesting epitaxial growth of the Nb-depletedβ phases from the preexisting β films.     

Enhanced Ferroelectric Polarization in Laser-ablated Bi<Subscript>4</Subscript>Ti<Subscript>3</Subscript>O<Subscript>12</Subscript> Thin Films by Controlling Preferred Orientation

Polycrystalline Bi₄Ti₃O₁₂ thin films with various fractions of a-axis, c-axis and random orientations have been grown on Pt(111)/Ti/SiO₂/Si substrates by laser-ablation under different kinetic growth conditions. The relationship between the structure and ferroelectric property of the films was investigated, so as to explore the possibility of enhancing ferroelectric polarization by controlling the preferred orientation. The structural characterization indicated that the large growth rate and high oxygen background pressure were both favorable for the growth of non-c-axis oriented grains in the Bi₄Ti₃O₁₂ thin films. The films with high fractions of a-axis and random orientations, i e, f (a-sxis) = 28.3% and f (random) = 69.6%, could be obtained at the deposition temperature of 973 K, oxygen partial pressure of 15 Pa and laser fluence of 4.6 J/cm², respectively. It was also noted that the variation of ferroelectric polarization was in accordance with the evolution non-c-axis orientation. A large value of remanent polarization (2Pr = 35.5 μC/cm²) was obtained for the Bi₄Ti₃O₁₂ thin films with significant non-c-axis orientation, even higher than that of rare-earth-doped Bi₄Ti₃O₁₂ films.     

Spontaneous Magnetic Transitions and Corresponding Magnetoelastic Properties of Intermetallic Compounds <Emphasis Type="Italic">R</Emphasis>Mn<Subscript>2</Subscript>Ge<Subscript>2</Subscript> (<Emphasis Type="Italic">R</Emphasis>=Gd,Tb and Dy)

The spontaneous magnetic transitions and corresponding magnetoelastic properties of intermetallic compounds RMn₂Ge₂ (R=Gd, Tb and Dy) were investigated by using the X-ray diffraction method and magnetic measurement. The results showed that the compounds experience two magnetic transitions, namely the second-order paramagnetic to antiferromagnetic transition at temperature T_N (T_N=368, 423 and 443 K for GdMn₂Ge₂, TbMn₂Ge₂ and DyMn₂Ge₂, respectively) and the first-order antiferromagnetic - ferrimagnetic transition at temperature T_t (T_t=96, 80 and 40 K for GdMn₂Ge₂, TbMn₂Ge₂ and DyMn₂Ge₂, respectively) as the temperature decreases. The temperature dependence of the lattice constant a(T) displays a negative magnetoelastic anomaly at the second-order transition point T_N and, at the first-order transition T_t, a increases abruptly for GdMn₂Ge₂ and TbMn₂Ge₂, Δa/a about 10^-3. Nevertheless, the lattice constant c almost does not change at these transition points indicating that such magnetoelastic anomalies are mainly contributed by the Mn-sublattice. The transitions of the magnetoelastic properties are also evidenced on the temperature dependence of magnetic susceptibility χ. The first-order transition behavior at T_t is explained by the Kittel mode of exchange inversion.     

Effects of the annealing heating rate on sputtered aluminum oxide films

Al_xO_y films by DC reactive magnetron sputtering were annealed in air ambient at 500 ℃for 1 h with different heating rates of 5,15,and 25 ℃/min.Then heat treatments at 900 ℃ were carried out on these 500 ℃-annealed films to simulate the high-temperature application environment.Effects of the annealing heating rate on structure and properties of both 500 ℃-annealed and 900 ℃-heated films were investigated systematically.It was found that distinct γ-Al_2O_3 crystallization was observed in the 900 ℃-heated films only when the annealing heating rates are 15 and 25 ℃/min.The 500 ℃-annealed film possessed the most compact surface morphology in the case of 25 ℃/min.The highest microhardness of both 500 ℃-annealed and 900℃-heated films were obtained when the annealing heating rate was 15 ℃/min.