Effect of compressed TiO2 nanoparticle thin film thickness on the performance of dye-sensitized solar cells

In this study, dye-sensitized solar cells (DSSCs) were fabricated using nanocrystalline titanium dioxide (TiO₂) nanoparticles as photoanode. Photoanode thin films were prepared by doctor blading method with 420 kg/cm² of mechanical compression process and heat treatment in the air at 500°C for 30 min. The optimal thickness of the TiO₂ NP photoanode is 26.6 μm with an efficiency of 9.01% under AM 1.5G illumination at 100 mW/cm². The efficiency is around two times higher than that of conventional DSSCs with an uncompressed photoanode. The open-circuit voltage of DSSCs decreases as the thickness increases. One DSSC (sample D) has the highest conversion efficiency while it has the maximum short-circuit current density. The results indicate that the short-circuit current density is a compromise between two conflict factors: enlargement of the surface area by increasing photoanode thickness and extension of the electron diffusion length to the electrode as the thickness increases.     

Enhancement of the photoelectric performance of dye-sensitized solar cells using Ag-doped TiO<Subscript>2</Subscript> nanofibers in a TiO<Subscript>2</Subscript> film as electrode

For high solar conversion efficiency of dye-sensitized solar cells [DSSCs], TiO₂ nanofiber [TN] and Ag-doped TiO₂ nanofiber [ATN] have been extended to be included in TiO₂ films to increase the amount of dye loading for a higher short-circuit current. The ATN was used on affected DSSCs to increase the open circuit voltage. This process had enhanced the exit in dye molecules which were rapidly split into electrons, and the DSSCs with ATN stop the recombination of the electronic process. The conversion efficiency of TiO₂ photoelectrode-based DSSCs was 4.74%; it was increased to 6.13% after adding 5 wt.% ATN into TiO₂ films. The electron lifetime of DSSCs with ATN increased from 0.29 to 0.34 s and that electron recombination was reduced.     

The influence of anatase-rutile mixed phase and ZnO blocking layer on dye-sensitized solar cells based on TiO2nanofiberphotoanodes

High performance is expected in dye-sensitized solar cells (DSSCs) that utilize one-dimensional (1-D) TiO₂ nanostructures owing to the effective electron transport. However, due to the low dye adsorption, mainly because of their smooth surfaces, 1-D TiO₂ DSSCs show relatively lower efficiencies than nanoparticle-based ones. Herein, we demonstrate a very simple approach using thick TiO₂ electrospun nanofiber films as photoanodes to obtain high conversion efficiency. To improve the performance of the DSCCs, anatase-rutile mixed-phase TiO₂ nanofibers are achieved by increasing sintering temperature above 500°C, and very thin ZnO films are deposited by atomic layer deposition (ALD) method as blocking layers. With approximately 40-μm-thick mixed-phase (approximately 15.6?wt.% rutile) TiO₂ nanofiber as photoanode and 15-nm-thick compact ZnO film as a blocking layer in DSSC, the photoelectric conversion efficiency and short-circuit current are measured as 8.01% and 17.3?mA?cm^?2, respectively. Intensity-modulated photocurrent spectroscopy and intensity-modulated photovoltage spectroscopy measurements reveal that extremely large electron diffusion length is the key point to support the usage of thick TiO₂ nanofibers as photoanodes with very thin ZnO blocking layers to obtain high photocurrents and high conversion efficiencies.     

Optimization of the dye-sensitized solar cell performance by mechanical compression

In this study, the P25 titanium dioxide (TiO₂) nanoparticle (NP) thin film was coated on the fluorine-doped tin oxide (FTO) glass substrate by a doctor blade method. The film then compressed mechanically to be the photoanode of dye-sensitized solar cells (DSSCs). Various compression pressures on TiO₂ NP film were tested to optimize the performance of DSSCs. The mechanical compression reduces TiO₂ inter-particle distance improving the electron transport efficiency. The UV–vis spectrophotometer and electrochemical impedance spectroscopy (EIS) were employed to quantify the light-harvesting efficiency and the charge transport impedance at various interfaces in DSSC, respectively. The incident photon-to-current conversion efficiency was also monitored. The results show that when the DSSC fabricated by the TiO₂ NP thin film compressed at pressure of 279 kg/cm², the minimum resistance of 9.38 Ω at dye/TiO₂ NP/electrolyte interfaces, the maximum short-circuit photocurrent density of 15.11 mA/cm², and the photoelectric conversion efficiency of 5.94% were observed. Compared to the DSSC fabricated by the non-compression of TiO₂ NP thin film, the overall conversion efficiency is improved over 19.5%. The study proves that under suitable compression pressure the performance of DSSC can be optimized.     

Conversion enhancement of flexible dye-sensitized solar cells based on TiO2 nanotube arrays with TiO2 nanoparticles by electrophoretic deposition

We prepared highly ordered titanium dioxide nanotube arrays (TNAs) by anodizing Ti foils in F⁻ containing electrolyte. The thickness and dye loading amount of TNAs were 26 μm and 1.06 × 10⁻⁷ mol cm⁻², respectively. TiO₂ nanoparticles (TNPs) were electrophoretically deposited on the inner wall of nanotube to produce coated nanotube arrays (TNAP). The dye loading was increased to 1.56 × 10⁻⁷ mol cm⁻², and the electron transport rate improved. TNAs and TNAP were sensitized with ruthenium dye N3 to yield dye-sensitized TiO₂ nanotube solar cells. The power conversion efficiency of TNA-based dye-sensitized solar cells (DSSCs) was 4.28%, whereas the efficiency of TNAP-based DSSCs increased to 6.28% when illuminated from the counter electrode. The increase of power conversion efficiency of TNAP-based DSSCs is ascribed to the increased surface area of TNAs and the faster electron transport rate.     

TiO2/modified natural clay semiconductor as a potential electrode for natural dye-sensitized solar cell

TiO₂/modified natural bentonite clay semiconductor, as a potential electrode of dye-sensitized solar cell, having a Ti:Si molar ratio of 85:15 was, for the first time, compared with pure TiO₂ (commercial P25) electrode in terms of solar cell efficiency and characteristics. 4-Chloro-2,5-difluorobenzoic acid and 4-(chloromethyl)benzoyl chloride were added to the electrodes to increase light harvesting ability of natural dyes extracted from red cabbage, rosella, and blue pea. The results showed that the TiO₂/clay semiconductor provided a higher surface area but a slightly lower efficiency than the pure TiO₂. The best natural sensitizer was found to be the dye extracted from red cabbage. Besides, the 4-(chloromethyl)benzoyl chloride provided a higher short circuit current for the TiO₂/clay semiconductor.     

Iodine-free organic dye sensitized solar cells with in situ polymerized hole transporting material from alkoxy-substituted TriEDOT

An alkoxy-substituted ethylenedioxythiophene (EDOT) trimer is designed and synthesized which has shown a low oxidation potential of 0.50 V versus saturated calomel electrode (SCE). In situ polymerization of the trimer in a thin layer electrolytic cell using organic dye adsorbed on TiO₂ as the working electrode yielded alkoxy-substituted poly(ethylenedioxythiophene) (PEDOT). With D149 as the dye sensitizer and the in situ polymerized polymer as hole-transporting material (HTM), dye sensitized solar cells (DSSCs) were fabricated to show a typical power conversion efficiency of 3.97% under AM 1.5 G (100 mW cm⁻²) illumination. The results show good promise of in situ polymerized conjugated polymers as HTM for iodine/iodide redox-free DSSC applications.     

Double‐Layer Structure Photoanode with TiO2 Nanotubes and Nanoparticles for Dye‐Sensitized Solar Cells

Here, we report a novel double‐layer structure photoanode with TiO₂ nanotube (TNT) layer and TiO₂ nanoparticle (TP) layer via a two‐step method of electrochemical anodization and screen printing for dye‐sensitized solar cells (DSSCs). The results indicate that DSSCs with this double‐layer structure have significant advantages of large surface area, long electron lifetime, superior electron recombination restraint characteristics, and high light scattering. The layer thickness of nanotubes and nanoparticles is also investigated and finally an optimized double‐layer structure with excellent performance is prepared. With such a double‐layer structure photoanode, DSSC with a relative high conversion efficiency of 6.43% and a short‐circuit photocurrent density of 16.40 mA·cm^?2 is obtained.     

Fabrication and photoelectrochemical properties of TiO2 films on Ti substrate for flexible dye-sensitized solar cells

The dye-sensitized solar cells (DSSCs) using Ti foil supporting substrate for fabricating nanocrystalline TiO₂ flexible film electrodes were developed, intending to improve the photoelectrochemical properties of flexible substrate-based DSSCs. The obtained cells were characterized by electrochemical impedance spectra (EIS), open circuit voltage decay (OCVD) measurement and Tafel plots. The experimental results indicate that the most important advantage of a Ti foil-based TiO₂ flexible electrode over a FTO glass-based electrode lies in its reduced sheet resistance, electron traps, and the retarded back reaction of electrons with tri-iodine ions in DSSCs. All above characteristics for the Ti substrate TiO₂ films are beneficial for decreasing the charge recombination in the TiO₂ electrode and prolonging the electron lifetimes for the DSSCs, as well as improvement of the overall solar conversion efficiency. The photocurrent of the cell fabricated with the Ti foil-based flexible electrode increased significantly, leading to a much higher overall solar conversion efficiency of 5.45% at 100 mW/cm² than the cell made with FTO glass-based TiO₂ electrodes. Above results demonstrate that Ti foil is a potential alternative to the conventional FTO glass substrate for the DSSCs.     

Dye-sensitized solar cells based on double-layered TiO2 composite films and enhanced photovoltaic performance

Dye-sensitized solar cells (DSSCs) are fabricated based on double-layered composite films of TiO₂ nanoparticles and hollow spheres. The photoelectric conversion performances of DSSCs based on nanoparticles/nanoparticles (PP), hollow spheres/hollow spheres (HH), hollow spheres/nanoparticles (HP), and nanoparticles/hollow spheres (PH) double-layered films are investigated, and their photo-electric conversion efficiencies are 4.33, 4.72, 4.93 and 5.28%, respectively. The enhanced performance of TiO₂ nanoparticles/hollow spheres double-layered composite film solar cells can be attributed to the combined effect of following factors. The light scattering of overlayer hollow spheres enhances harvesting light of the DSSCs and the underlayer TiO₂ nanoparticle layer ensures good electronic contact between film electrode and the F-doped tin oxide (FTO) glass substrate. Furthermore, the high surface areas and pore volume of TiO₂ hollow spheres are respectively beneficial to adsorption of dye molecules and transfer of electrolyte solution.     

Mesoporous TiO<Subscript>2</Subscript> microspheres synthesized via a facile hydrothermal method for dye sensitized solar cell applications

Mesoporous TiO₂ microspheres were successfully synthesized by a facile hydrothermal process and the obtained product was sintered at 450 °C. The sintered TiO₂ powder was characterised by powder X-ray diffraction pattern and the result shows pure anatase phase with good crystalline nature. The morphological image of field emission scanning electron microscopy and high resolution transmission electron microscopy shows spherical shape and size of the particles is around 100 to 300 nm. The Brunauer–Emmett–Teller surface area of synthesized TiO₂ material was 56.32 m² g^?1 and average pore width of synthesized materials was 7.1 and 9.3 nm. Bimodal pore structure of TiO₂ microspheres has been very effective for electrolyte diffusion into photoanode in dye sensitized solar cells. The synthesized anatase TiO₂ microsphere based dye sensitized solar cells have high surface area with light scattering effect to enhance the photocurrent and conversion efficiency than the commercial P25 photoanode material. The power conversion efficiency of synthesized mesoporous TiO₂ microspheres and commercial P25 material is 4.2 and 2.7 % respectively. Therefore bimodal mesoporous anatase TiO₂ microsphere appears to be a promising and potential candidate for dye sensitized solar cells (DSSC) application.     

Plasmonic Effects of Infiltrated Silver Nanoparticles Inside TiO2 Film: Enhanced Photovoltaic Performance in DSSCs

The plasmonic effects of infiltrated silver (Ag) nanoparticles, with different contents, inside a nanostructured TiO₂ film on the photovoltaic performance of dye‐sensitized solar cells (DSSCs) are explored. The synthesized Ag nanoparticles are immobilized onto deposited TiO₂ nanoparticles by a new strategy using 3‐mercaptopropionic acid (MPA), a bifunctional linker molecule. Transmission electron microscope (TEM) images show that monodispersed Ag and polydispersed TiO₂ nanoparticles have an average diameter of 12 ± 3 nm and 5 ± 1 nm, respectively. Moreover, Fourier transform infrared spectroscopy (FTIR) analysis reveals that Ag nanoparticles were successfully functionalized and capped with MPA. Optical studies on the MPA‐capped Ag nanoparticles inside TiO₂ film show an increase in the total absorbance of the electrode. Moreover, EIS measurements confirm that MPA‐capped Ag nanoparticles inhibit the charge recombination and improve the stability of nanoparticles in I₃^?/I^? electrolyte. The DSSC assembled with optimal content of MPA‐capped Ag nanoparticles demonstrated an enhanced power conversion efficiency (8.82% ± 0.07%) compared with the pure TiO₂ (7.30% ± 0.05%). The increase in cell efficiency was attributed to the enhanced dye light absorption in strength and spectral range due to the surface plasmon resonance of MPA‐capped Ag nanoparticles in the photoanode.     

Quasi solid state dye-sensitized solar cells with modified TiO2 photoelectrodes and triphenylamine-based dye

Quasi solid state dye-sensitized solar cells (DSSCs) have been fabricated with organic sol or TiCl₄ modified TiO₂ and porous TiO₂ photoanode and a triphenylamine-based dye (TPAR3) used as photosensitizer. Dark current measurements suggested that both modified TiO₂ photoelectrodes had significantly reduced the recombination rate of photoelectrons due to the reduced bare FTO surface in comparison to porous photoelectrode. The DSSC based on modified TiO₂ photoelectrodes showed improved photovoltaic parameters compared to the porous TiO₂ photoelectrode. The overall power conversion efficiency (PCE) is 3.27%, 4.73% and 6.8% for porous, TiCl₄ modified and sol modified TiO₂ photoelectrodes, respectively. The improved PCE with modified TiO₂ electrodes was attributed to the formation of a compact layer. This effectively improves adherence of TiO₂ to FTO surface, providing a larger TiO₂/FTO contact area and reducing the electron recombination by blocking the direct contact between redox electrolyte and the conductive FTO surface and enhances the electron collection efficiency.     

Carbazole based hole transporting materials for solid state dye sensitizer solar cells: role of the methoxy groups

The synthesis of new organic hole transporting materials (HTMs) based on 3,6‐disubstituted 9H‐carbazole‐3,6‐diamine,N,N,N′,N′‐tetraphenyl‐9‐(4‐methoxyphenyl) derivatives and their applications in solid state dye sensitizer solar cells (DSSCs) are described. The effect of the methoxy group localized on the para position of the diphenylamine moieties on the thermal, electronic and electrochemical properties and photovoltaic performance is discussed. In solid state DSSCs, utilization of the aforementioned HTMs in combination with the dye D102 (TiO₂/D102/HTM/Au) shows a positive influence of the methoxy group on the photovoltaic conversion efficiency compared with unsubstituted diphenylamine grafted groups. A study on the concentration of the HTM is also carried out and shows an optimal concentration around 200 mg mL^?1. Without further optimization, the best device gives a power conversion efficiency of 1.75% under AM 1.5 solar irradiation (100 mW cm^?2).     

Enhancing the performance of dye-sensitized solar cells based on an organic dye by incorporating TiO2 nanotube in a TiO2 nanoparticle film

The photoelectrochemical properties of a high molar extinction coefficient charge transfer organic dye containing thienylfluorene segment called FL, and the effect of incorporating TiO₂ nanotube (TiNT) in TiO₂ nanoparticle film along with the above dye on the photovoltaic performance of dye-sensitized solar cells (DSSCs) were investigated. The influence of soaking time of the TiO₂ electrode in dye solution and the effect of varying its concentration, on the solar cell efficiency was also studied. Cyclic voltammetric (CV) analysis revealed the linear relationship between the anodic peak current and the scan rate, indicating a surface-confined diffusion process.The surface morphology of TiNT was characterized using SEM, TEM and XRD. The open-circuit voltage (V_OC) of the DSSC increased with the increase in the wt% of TiNT and shows optimal value at about 5 wt%, which is correlated with the suppression of the electron recombination as found out from the electron lifetime studies.The electrochemical impedance spectroscopy (EIS) technique was employed to quantify the charge transport resistance (R_ct) and electron lifetime under different ratios of the TiNT/nanoparticle. The electron lifetimes of the DSSCs based on FL and N3 dye were very close to one another and the DSSC based on the FL showed respectable photovoltaic performance of ca. 7.8% under the light intensity of 100 mW cm⁻² (AM 1.5G).     

Properties of sol-gel SnO2/TiO2 electrodes and their photoelectrocatalytic activities under UV and visible light illumination

A visible light active binary SnO₂-TiO₂ composite was successfully prepared by a sol-gel method and deposited on Ti sheet as a photoanode to degrade orange II dye. Titanium and SnO₂ can promote the development of rutile phase of TiO₂ and inhibit the formation of anatase phase of TiO₂. Formation of SnO₂ crystalline is insignificant even when the calcination temperature increases to 700 °C. Heterogenized interface between SnO₂ and TiO₂ inhibits growth of TiO₂ linkage and leads to the particle-filled surface morphology of SnO₂-containing films. The carbonaceous, Ti-O-C bonds and Ti³⁺ species are likely to account for the photoabsorption and photoelectrocatalytic (PEC) activity under visible light illumination. The electrode with 30% SnO₂ exhibits higher photocurrent when compared with those in the region of 0-50%. The 600 °C-calcined SnO₂-TiO₂ electrode indicates higher activity when compared with those at 400, 500, 700 and 800 °C. PEC degradation of orange II follows the Langmuir-Hinshelwood model and takes place much effectively in a solution of pH 3.0 than those in pH 7.0 and pH 11.0.     

Hydrothermal Growth and Application of ZnO Nanowire Films with ZnO and TiO2 Buffer Layers in Dye-Sensitized Solar Cells

This paper reports the effects of the seed layers prepared by spin-coating and dip-coating methods on the morphology and density of ZnO nanowire arrays, thus on the performance of ZnO nanowire-based dye-sensitized solar cells (DSSCs). The nanowire films with the thick ZnO buffer layer (~0.8–1 μm thick) can improve the open circuit voltage of the DSSCs through suppressing carrier recombination, however, and cause the decrease of dye loading absorbed on ZnO nanowires. In order to further investigate the effect of TiO₂ buffer layer on the performance of ZnO nanowire-based DSSCs, compared with the ZnO nanowire-based DSSCs without a compact TiO₂ buffer layer, the photovoltaic conversion efficiency and open circuit voltage of the ZnO DSSCs with the compact TiO₂ layer (~50 nm thick) were improved by 3.9–12.5 and 2.4–41.7%, respectively. This can be attributed to the introduction of the compact TiO₂ layer prepared by sputtering method, which effectively suppressed carrier recombination occurring across both the film–electrolyte interface and the substrate–electrolyte interface.     

Fabrication of Three-Dimensionally Ordered Macroporous TiO2 Films with Enhanced Photovoltaic Conversion Efficiency

Negative-charged polystyrene (PS) microspheres were prepared through a soap-free emulsion polymerization method using potassium persulfate as initiator. Three-dimensionally ordered macroporous TiO₂ films were fabricated using the high-quality PS colloidal crystals templates obtained via a horizontal deposition method. The as-prepared macroporous TiO₂ films were applied as the photoanodes in dye-sensitized solar cell (DSSC). The microstructure of the products were characterized by X-ray diffractometer, fourier transform infrared spectroscopy, scanning electron microscopy, transmission electron microscopy and nitrogen adsorption–desorption analyzer. The results showed that the macroporous TiO₂ films replicated well the 3D ordered structure derived from PS colloidal crystal templates and revealed a relatively large specific surface area (69.99 m²/g), which could increase the capacity of TiO₂ film anode for absorbing dyes and scattering light. The photocurrent–voltage (I–V) characteristics of DSSC were measured by a digital source meter under simulated solar light. The results indicated that the introduction of an ordered macroporous TiO₂ interfacial layer increased the photovoltaic conversion efficiency, which was improved by 68 % from 3.61 to 6.08 %, as compared to a device using a bare P25 TiO₂ photoanode. Our results showed that the hierarchically ordered macroporous TiO₂ bilayer films photoanode for DSSC could be helpful to improve the photovoltaic conversion efficiency.     

Enhanced performance of a dye-sensitized solar cell with a modified poly(3,4-ethylenedioxythiophene)/TiO2/FTO counter electrode

ClO₄⁻-poly(3,4-ethylenedioxythiophene)/TiO₂/FTO (ClO₄⁻-PEDOT/TiO₂/FTO) counter electrode (CE) in dye-sensitized solar cells (DSSCs) is fabricated by using an electrochemical deposition method. Comparing with the DSSCs with ClO₄⁻-PEDOT/FTO counter electrode, the photocurrent-voltage (I-V) measurement reveals that the photocurrent conversion efficiency (η), fill factor (FF) and short-circuit current density (J_SC) of DSSCs with a ClO₄⁻-PEDOT/TiO₂/FTO CE increase. The enhanced performances of the DSSCs are attributed to the higher J_SC arising from the increase of active surface area of ClO₄⁻-PEDOT/TiO₂/FTO CE. Electrochemical impedance spectra (EIS) also indicate that the charge-transfer resistance on the ClO₄⁻-PEDOT/electrolyte interface decreases. Cyclic voltammetry results indicate that the ClO₄⁻-PEDOT/TiO₂/FTO electrode shows higher activity towards I₃⁻/I⁻ redox reaction than that of ClO₄⁻-PEDOT/FTO electrode.     

Performance enhancement of dye-sensitized solar cells using nanostructural TiO2 films prepared by a graft polymerization and sol–gel process

Nanostructural TiO₂ films with large surface areas were prepared by the combined process of graft polymerization and sol–gel for use in dye-sensitized solar cells (DSSCs). The surface of the TiO₂ nanoparticles was first graft polymerized with photodegradable poly(methyl methacrylate) (PMMA) via atom transfer radical polymerization (ATRP), after which the particles were deposited onto a conducting glass. The PMMA chains were removed from the TiO₂ films by UV irradiation to generate secondary pores, into which titanium isopropoxide (TTIP) was infiltrated. The TTIP was then converted into small TiO₂ particles by calcination at 450 °C, as characterized by energy-filtering transmission electron microscopy (EF-TEM) and field emission scanning electron microscopy (FE-SEM). The nanostructural TiO₂ films were used as a photoelectrode in solid-state DSSCs; the energy conversion efficiency was 5.1% at 100 mW/cm², which was higher than the values achieved by the pristine TiO₂ (3.8%) and nongrafted TiO₂/TTIP photoelectrodes (3.3%). This performance enhancement is primarily due to the increased surface area and pore volume of TiO₂ films, as revealed by the N₂ adsorption–desorption isotherm.