Interactions in poly(vinyl chloride)–lignin blends

In rigid poly(vinyl chloride) (PVC)-lignin (L) blends the possibility of forming intermolecular interactions between the PVC and L can take place only at low L loading (up to 10 parts). At high L loading there is an imbalance between the tendency of L molecular components to associate by H-secondary bonds, and the potential for forming intermolecular bonds with PVC. Our studies have shown that specific plasticizers could break parts of the H-secondary bonds present in L, thus creating possibilities of interactions at a molecular scale with other polar polymers by forming intermolecular bonds. The presence of specific plasticizers strongly influences the properties and the morphology of the blends, and permits higher L loading. The data regarding the properties of plasticized copolymer (vinyl chloride-vinyl acetate) (VC-VAc)-L blends show the important role of these specific plasticizers. Some results show also the possibility of L-filler interaction. The blends were studied with regard to their morphology by Differential Scanning Calorimetry (DSC), Dynamic Mechanical Analysis (DMA), Fourier Transform Infrared (FT-IR) Spectroscopy, Scanning Electron Microscopy (SEM) and with regard to their mechanical properties by tensile testing.     

Molecular weight effect on theta-gel formation in poly(vinyl alcohol)–poly(ethylene glycol) mixtures

Injectable hydrogel formulations that undergo in situ gelation at body temperature are promising for minimally invasive tissue repair. This work focuses on the investigation of injectable poly(vinyl alcohol) (PVA) and poly(ethylene glycol) (PEG) mixtures. The injectable PVA–PEG aqueous solutions form a hydrogel as temperature is reduced to near body temperature, while filling a defect in the injection site. Gamma sterilization of these solutions compromises injectability presumably due to crosslinking of PVA. We hypothesized that by modifying the PEG molecular weight and its concentration, injectability of radiation sterilized PVA–PEG hydrogels can be optimized without compromising the mechanical properties of the resulting gel. The use of a bimodal mixture of higher and lower molecular weight PEG (600 and 200 g/mol) resulted in lower PVA/PEG solution viscosity, better injectability, and higher gel mechanical strength. The PVA/bimodal-PEG had a lower viscosity at 2733 ± 149 cP versus a viscosity of 5560 ± 278 cP for PVA/unimodal-PEG (400 g/mol). The gel formed with the bimodal PEG mixture had higher creep resistance (61% total creep strain under 0.5 MPa) than that formed with unimodal PEG (84%). These hydrogel formulations are promising candidates for minimally invasive tissue repair. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Modeling of interdiffusion in poly(vinyl acetate)–poly(methyl methacrylate)–toluene multicomponent systems

Work on interdiffusion has been mainly carried out in binary systems in the past, and this work has focused on polymer–solvent (S) systems and polymer blends. To understand and predict the interdiffusion of two solids in the presence of one S, we present a new mathematical model based on the Onsager approach. Within our model, interdiffusion kinetics are described with a modification of the reptation model for long polymer chains, and the chemical potential gradient is used as the driving force behind mass transfer. The chemical potential is calculated with a Flory–Huggins approach. The model was validated with 29 Raman spectroscopy experiments in poly(vinyl acetate)–poly(methyl methacrylate)–toluene systems at 20 °C. Monomer mobilities (L _i,0s) were determined for both polymers to show the independence of L _i,0 from the chain length. The L _i,0s were found to be strongly dependent on the S content. With the knowledge of phase equilibria and L _i,0s, interdiffusion in the ternary polymer–polymer–S system could be predicted by the introduced model. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47092.     

Reversibility of thermodynamic lower critical solution temperature phenomenon in miscible poly(ε-caprolactone)/poly(benzyl methacrylate)

Differential scanning calorimetry and optical microscopy were performed to examine the reversibility of phase separation at above the lower critical solution temperatures in a miscible poly(ε-caprolactone) (PCL)/poly(benzyl methacrylate) (PBzMA) blend system. Upon heating, phase separation occurred via a binodal nucleation and growth (NG) mechanism at above 240 °C, which is a lower critical solution temperature (LCST). The pattern of phase domains suggests that the phase separation was meta-stable. Interestingly, the LCST phase separation was found to be readily reversible to original homogeneity upon cooling at regularly accessible rates. A major factor may be that the temperature window between the LCST curve and blend T_g curve is wide, resulting in a convenient temperature range for the polymer chains to kinetically reorganize to a state favored by the thermodynamic conditions.     

Polystyrene–poly(ethylene oxide) diblock copolymers micelles in water

Micellization in water of polystyrene–poly(ethylene oxide) diblock copolymers is achieved by the stepwise dialysis technique in order to prepare micellar solutions for copolymers with a wide range of molecular parameters. Hydrodynamic radii, determined by quasielastic light scattering, are correlated with the molecular parameters, e.g. molecular weight and composition, and compared with the theory. Two couples of phenanthrene and anthracene labelled copolymers are used to prepare micellar solutions by mixing them before and after dialysis. The non radiative energy transfer is determined on these solutions to prove that polystyrene-poly(ethylene oxide) diblock copolymers micelles in water are "frozen" micelles even when heated near the Tg of polystyrene. Received: 3 November 1997/Revised version: 1 December 1997/Accepted: 2 December 1997     

Thermal transitions in poly(alkyl-4,4′-diphenoxy terephthalate)s

Summary The thermal transitions of poly(alkyl-4,4-diphenoxy terephthalate)s, in which the flexible spacer contains 5,6 and 7 methylene groups, have been studied by thermogravimetry, differential scanning calorimetry, X ray diffraction, thermoptical microscopy and small angle light scattering. The series shows a marked influence of the even and odd number of methylene groups on the crystal-liquid crystal transition temperatures and on the isotropization transition temperature. Nematic mesophases have been observed for the odd terms, and a transition from a smectic to a nematic mesophase has been observed for the even term.     

Oxidative degradation of poly (vinyl acetate) and poly (ε-caprolactone) and their mixtures in solution

The oxidative degradation of the poly (ε-caprolactone) (PCL), poly (vinyl acetate) (PVAC) and their mixtures in dichlorobenzene has been investigated at various temperatures (70-130°C) in the presence of benzoyl peroxide. The interaction between the polymers is quantified by monitoring the molecular weights of individual polymers using gel-permeation chromatography. The various physical mixtures employed in the present investigation are , and wt%/wt% PCL/PVAC. Experimental data indicated that the degradation is random without cross-linking and repolymerization. An optimum in degradation temperature (corresponding to maximum degradation rate) of 105°C was observed for the entire range of polymer compositions (0-100% PCL) investigated. This optimum temperature of degradation is characteristic mostly of the initiator and only to a small extent of the degrading polymer system. The experimental results of the mixtures indicated that the degradation rates of PVAC are significantly enhanced, while the degradation rates of PCL are decreased in the physical mixture. This can be attributed to the proton-accepting and proton-donating nature of PCL and PVAC, respectively. A radical mechanism for the oxidative degradation of pure polymers and their mixtures has been proposed and a model based on continuous distribution kinetics was developed considering the interaction of the polymers through hydrogen abstraction and the parameters were evaluated numerically. The activation energies for the peroxide attack for the PCL and PVAC are 10.5 and , respectively. The activation energies for the random chain scission of PCL and PVAC are 10.6 and , respectively.     

Miscibility behaviour of sulfonylated poly(2,6-dimethyl-1,4-phenylene oxide) copolymers in the blends with poly(styrene-co-maleic anhydride) and with poly(α-methylstyrene-co-maleic anhydride)

Summary The miscibility behaviour of sulfonylated poly(2,6-dimethyl-1,4-phenylene oxide) of the different degree of sulfonylation blended with poly(styrene-co-maleic anhydride) or poly(-methylstyrene-co-maleic anhydride) was studied. The critical degree of sulfonylation for phase separation in these blends was found to be 55 mole % and 66 mole %, respectively. The miscibility behaviour was analyzed on the basis of the mean field treatment and studied by DSC.Dedicated to Professor Dragutin Fle in honor of his 70th birthday     

High-pressure solution blending of poly(?-caprolactone) with poly(methyl methacrylate) in acetone + carbon dioxide

The miscibility of blends of poly(?-caprolactone) (PCL, M_w = 14,300) with poly(methyl methacrylate) (PMMA, M_w = 15K or 540K) in acetone + CO₂ mixed solvent has been explored. The liquid-liquid phase boundaries at different temperatures have been determined for mixtures containing 10 wt% total polymer blend, 50 wt% acetone and 40 wt% CO₂. The PCL and PMMA contents of the blends were varied while holding the total polymer concentration at 10 wt%. The polymer blend solutions all displayed LCST-type behavior and required higher pressures than individual polymer components for complete miscibility. Complete miscibilities were achieved at pressures within 40 MPa. The DSC scans show that the blends are microphase-separated. The blends display the melting transition of PCL and the glass transition temperature of the PMMA phases. The presence of PMMA is found to influence the crystallization and melting behavior of PCL in the blends. The DSC results on heat of melting and the FTIR spectra, specifically the changes at 1295 cm⁻¹ band show the changes (decrease) in overall crystallinity of the blend upon addition of PMMA.     

Crystal orientation of poly(?-caprolactone) blocks confined in crystallized polyethylene lamellar morphology of poly(?-caprolactone)-block-polyethylene copolymers

The crystal orientation of poly(?-caprolactone) (PCL) blocks in PCL-block-polyethylene (PE) copolymers has been investigated using two-dimensional small-angle X-ray scattering (2D-SAXS) and 2D wide-angle X-ray diffraction (2D-WAXD) as a function of crystallization temperature T_c and thickness of PCL layers d_PCL. The PCL blocks were spatially confined in the solid lamellar morphology formed by the crystallization of PE blocks (PE lamellar morphology), an alternating structure of crystallized PE lamellae and amorphous PCL layers. This confinement is expected to be intermediate between hard confinement by glassy lamellar microdomains and soft confinement by rubbery ones, because the crystallized PE lamellae consist of hard PE crystals covered with amorphous (or soft) PE blocks. The 2D-SAXS results showed uniaxial orientation of the PE lamellar morphology after applying the rotational shear to the sample. Therefore, it was possible to investigate crystal orientation of PCL blocks within the oriented PE lamellar morphology. The 2D-WAXD results revealed that the c axis of PCL crystals (i.e., stem direction of PCL chains) was parallel to the lamellar surface normal irrespective of T_c when 16.5 nm ≥ d_PCL ≥ 10.7 nm. However, it changed significantly with changing T_c when d_PCL = 8.8 nm; the c axis was perpendicular to the lamellar surface normal at 45 °C ≥ T_c ≥ 25 °C while it was almost random at 20 °C ≥ T_c ≥ 0 °C. These results suggest that the PE lamellar morphology plays a similar role to glassy lamellar microdomains regarding spatial confinement against subsequent PCL crystallization.     

Rheologically determined phase diagram of poly(ε-caprolactone)/poly(styrene-co-acrylonitrile) blends: Role of ramp rate in dynamic measurements

The phase behavior of poly(ε-caprolactone) (PCL)/poly(styrene-co-acrylonitrile) (SAN) blends, with a lower critical solution temperature (LCST)-type phase diagram over a virtual upper critical solution temperature (UCST) one, was investigated through thermal analysis and dynamic rheological measurements as a function of ramp rate. The LCST phase diagram was detected rheologically from the observed slope changes in the dynamic temperature ramps of storage modulus (G′). The determined phase transition points along with the spinodal temperatures, which are estimated based on the theoretical approach of Ajji and Choplin's mean field theory, shift to higher temperatures by reducing the ramp rate. The detected shifts show a composition dependency. Far away from the critical point, the phase transition temperatures of PCL/SAN blends change more noticeably, which originates from the smaller magnitude of concentration fluctuations in the metastable region and the stronger competition between the phase dissolution and cooling rate. The Flory–Huggins interaction parameter (χ) was appropriately adjusted into the LCST phase boundary as a function of temperature and composition. The results confirmed that the adjusted χ has higher temperature dependency at larger ramp rate of the dynamic measurements. The experimentally combined LCST and UCST phase behavior were also verified by the compressible regular solution model. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47750.     

Miscibility of poly(styrene-co-vinyl phenol) with poly(ɛ-caprolactone)

Summary Poly(styrene-co-vinyl phenol) (STVPh)/poly(-caprolactone)(PCL) blends showed enhanced miscibility over polystyrene/PCL blend, and showed single glass transition temperature when the contents of vinyl phenol (VPh) in copolymer were higher than 10 wt % (maximum content of VPh in STVPh used in this study was 20 wt%). STVPh 4, STVPh 7, STVPh 10 (4, 7, 10 were VPh wt%)/PCL blends showed cloud points on heating for miscible blend system, and this phase separation was reversible on cooling. From melting point depression of PCL, interaction parameter, B. for miscible STVPh 12/PCL blend system was evaluated.     

Effects of liquid–liquid phase separation on crystallization of poly(ethylene glycol) in blends with isotactic poly(methyl methacrylate)

To analyze the interplay between crystallization and liquid–liquid phase separation (LLPS), isothermal crystallization behavior of poly(ethylene glycol) (PEG) in blends with isotactic poly(methyl methacrylate) (i-PMMA) was investigated by differential scanning calorimetry (DSC). The blend system had an upper critical solution temperature (UCST) type phase diagram. When the crystallization occurred simultaneously with LLPS, the overall crystallization rate was enhanced at high crystallization temperatures T_c, relatively compared with that of neat PEG. This behavior was interpreted by the combination of the effects of spinodal quench depth ?T_s and usual supercooling degree ?T_c, according to the theory of Mitra and Muthukumar, namely, the crystallization rate is enhanced by the concentration fluctuation-assisted nucleation at high T_c. In the crystallization after LLPS proceeded, on the other hand, the overall crystallization rate was slow and less dependent on the blend composition. In addition, it was revealed by small-angle X-ray scattering measurements that amorphous i-PMMA was excluded from the interlamellar region of PEG crystals in SQ as well as WQ.     

Study of interphase in glass fiber–reinforced poly(butylene terephthalate) composites

It is well known that application of a coupling agent to a glass fiber surface will improve fiber/matrix adhesion in composites. However, on commercial glass fibers the coupling agent forms only a small fraction of the coating, the larger part being a mixture of processing aids whose contribution to composite properties is not well defined. The interfacial region of the composite will therefore be affected by the coating composition but also by the chemical reactions involved in the vicinity of the fiber and inside the surrounding matrix. The main feature of this study consists in dividing the interface region into two separate regions: the fiber/sizing interphase and the sizing/matrix interphase. A wide range of techniques was used, including mechanical and thermomechanical tests, infrared spectroscopy, gel permeation chromatography, carboxyl end group titrations, extraction rate measurements, and viscosity analysis. Experiments were performed on poly(butylene terephthalate) composites and results indicate that the adhesion improvement is due to the presence of a short chain coupling agent and of a polyfunctional additive, which may react both with the coupling agent and the matrix. According to the nature of this additive, it may be possible to soften the interphase and then to increase the composite impact strength.     

Surface hierarchical porosity in poly (ɛ-caprolactone) membranes with potential applications in tissue engineering prepared by foaming in supercritical carbon dioxide

This article describes the preparation of porous poly (ɛ-caprolactone), PCL, membranes by supercritical CO₂ (SCCO₂) foaming, displaying surface hierarchical macroporosity which could be tailored by careful control of the pressure, in the range of 150–250 bar, and depressurization processes in several steps, showing also pore interconnectivity between both membrane faces. The membranes exhibited two distinct types of surface macroporosity, the larger with diameter sizes of 300–500 μm were surrounded by and also composed of smaller pores of 15–50 μm (same size as inner pores). Membranes were prepared by solvent casting and submitted to different SCCO₂ foaming. Parameters such as membrane thickness, CO₂ flow, foaming time, pressure, temperature and the depressurization processes (rate and profiles), were varied to determine their influence on final porosity and to decipher which parameters were the most critical ones in terms of surface hierarchical pore organization. No remarkable changes in PCL crystallinity were found when membranes were processed under SCCO₂. Finally, biological evaluation of the porous membranes was achieved by seeding human skin fibroblasts on the prepared membranes. The results, in terms of cell adhesion, spreading, proliferation and metabolic activity indicate that these membranes could hold promise for the fabrication of meshes with controlled porosity for tissue engineering applications.     

Li+ ion conduction mechanism in poly (ε-caprolactone)-based polymer electrolyte

In this work, solid polymer electrolytes based on poly(?-caprolactone) (PCL) with lithium bis(oxalato)borate as a doping salt were prepared by solution cast technique using DMF as a solvent. The electrical DC conductivity and dielectric constant of the solid polymer electrolyte samples were investigated by electrochemical impedance spectroscopy over a frequency range from 50 Hz to 1 MHz. It was found that the DC conductivity increased with increase in the salt concentration to up to 4 wt% and thereafter decreased. Dielectric constant versus salt concentration was used to interpret the decrease in DC conductivity with increase in salt concentration. The DC conductivity as a function of temperature follows Arrhenius behavior in low temperature region, which reveals that ion conduction occurs through successful hopping. The curvature of DC conductivity at high temperatures indicates the contribution of segmental motion to ion conduction. High values for dielectric constant and dielectric loss were observed at low frequencies. The plateau of dielectric constant and dielectric loss at high frequencies can be observed as a result of rapid oscillation of the AC electric field. The HN dielectric function was utilized to study the dielectric relaxation. The experimental and theoretical data of dielectric constant are very close to each other at low temperatures. At high temperatures, the simulated data are more deviated from the experimental curve of dielectric constant due to the dominance of electrode polarization. The non-unity of relaxation parameters (α and β) reveals that the relaxation processes in PCL-based solid electrolyte is a non-Debye type of relaxation.     

Advance application of Raman spectroscopy for quantitative analysis of noncrystalline components in thin films of poly(ε-caprolactone)/poly(butadiene) blends

A quantitative analysis method for the distribution of noncrystalline poly(butadiene) component in poly(ε-caprolactone)/poly(butadiene) (PCL/PB) binary blends have been analyzed by advance application of Raman spectroscopy, optical microscopy, and differential scanning calorimetry (DSC) techniques. Thin films of different compositions of PCL/PB binary blends were prepared from solution and isothermally crystallized at a certain temperature. After calibration with real data, quantitative analyses by Raman spectroscopy revealed the amorphous PB are trapped inside the PCL crystals. Polarized optical microscopy and real time atomic force microscopy were used to collect data for the crystal morphology and crystal growth rate. For pure PCL crystals, a morphology of truncated lozenge shape was observed, independent of crystallization temperature and regardless of the blends compositions. For the pure PCL and their blends, almost unique crystal growth rate was found. The miscibility behaviors using DSC were drawn through melting point depression method. The Hoffman-Weeks extrapolations of the blends were found to be linear and identical with those of the neat PCL. The interaction parameter for the blends indicating that the PCL and PB blends have no intermolecular interaction, confirming the blends are immiscible. Despite the immiscibility of the blend, the PCL crystals do not bend during the growth process and do not reduce the growth rate as they do for miscible blend systems.     

Rheological properties of poly(ε-caprolactone) and poly(styrene-co-acrylonitrile) blends

Summary Rheological properties of poly(-caprolactone) (PCL) and Poly (styrene-co-acrylonitrile) (SAN) blends were examined as a function of the acrylonitrile (AN) content in SAN, to systematically understand the correlation between the interaction parameter and the theological properties of miscible polymer blends. When the plateau modulus (G _N ⁰) and zero shear viscosity ( ₀) of the PCL/SAN blends are plotted against the AN content in SAN, a minimum is observed. Qualitatively, the results obtained parallel the variation of the interchain interaction with the AN content. The negative deviation ofG _N ⁰ and ₀ from linearity seems to be attributed to the increase in the entanglement molecular weight between dissimilar chains which results from the chain extension caused by interchain interaction.