Polyimides from 2,3,3′,4′-biphenyltetracarboxylic dianhydride and aromatic diamines

A series of new polyimides were prepared from the reaction of 2,3,3′,4′-biphenyltetracarboxylic dianhydride (a-BPDA) with various aromatic diamines. The properties of the a-BPDA polyimides were compared with those of polyimides prepared from the reaction of 3,3′,4,4′-biphenyltetracarboxylic dianhydride (s-BPDA) with the same aromatic diamines. Films of the a-BPDA polyimides had higher glass transition temperatures (T_gs) and less color than the corresponding s-BPDA polyimide films. Light transmission at 500 nm, solar absorptivity, and thermal emissivity were determined on certain films. Films of similar polyimides based upon a-BPDA and s-BPDA containing meta linkages and others containing para linkages were each cured at 250, 300, and 350 °C. The films were characterized primarily by T_g, color, optical transparency, tensile properties, dynamic mechanical thermal analysis, and coefficient of thermal expansion. The a-BPDA meta linked polyimide films had tensile strengths and moduli higher than films of the a-BPDA para linked polyimide. The same phenomenon was not observed for the s-BPDA meta and para linked polyimides. The chemistry, mechanical, and physical properties of the polymers and films are discussed.     

Synthesis and properties of fluorinated polyimides. 3. Derived from novel 1,3-bis[3′-trifluoromethyl-4′(4″-amino benzoxy) benzyl] benzene and 4,4-bis[3′-trifluoromethyl-4′(4-amino benzoxy) benzyl] biphenyl

Novel diamine monomers, 1,3-bis[3′-trifluoromethyl-4′(4″-amino benzoxy) benzyl] benzene (IV) and 4,4-bis[3′-trifluoromethyl-4′(4-amino benzoxy) benzyl] biphenyl (V) have been synthesized. These monomers lead to several novel fluorinated polyimides on reaction with different commercially available dianhydrides like pyromellatic dianhydride (PMDA), benzophenone tetracarboxylic acid dianhydride (BTDA) or 2,2-bis(3,4-dicarboxyphenyl) hexafluoropropane (6FDA). The polyimides prepared from above two monomers on reaction with 6FDA are soluble in several organic solvents such as N,N-dimethyl formamide (DMF), N,N-dimethyl acetamide (DMAc) and tetrahydrofuran (THF). The polyimides prepared from PMDA/IV is soluble in DMF and N-methyl pyrollidone (NMP) on heating, whereas V/PMDA is insoluble in all solvents. BTDA/IV polyimide is also soluble in NMP, DMF and DMAc. These polyimide films have low water absorption rate 0.2-0.7% and low dielectric constant 2.74-3.2 at 1 MHz. These polyimides showed very high thermal stability even up to 531 °C for 5% weight loss in synthetic air and glass transition temperature up to 316 °C (by DSC) in nitrogen. All polyimides formed tough transparent films, with tensile strength up to 148 MPa, a modulus of elasticity up to 2.6 GPa and elongation at break up to 31% depending upon the exact repeating unit structure.     

Synthesis and characterization of novel fluorinated polyimides derived from 4,4′-[2,2,2-trifluoro-1-(3,5-ditrifluoromethylphenyl)ethylidene]diphthalic anhydride and aromatic diamines

A novel fluorinated aromatic dianhydride, 4,4′-[2,2,2-trifluoro-1-(3,5-ditrifluoromethylphenyl) ethylidene] diphthalic anhydride (9FDA), was synthesized, which was employed to polycondense with various aromatic diamines, including 4,4′-oxydianiline, 1,4-bis(4-aminophenoxy) benzene, 3,4′-oxydianiline and 1,4-bis(4-amino-2-trifluoromethylphenoxy)benzene to produce a series of fluorinated aromatic polyimides. The fluorinated polyimides obtained had inherent viscosities ranged of 0.61-1.14 dL/g and were easily dissolved both in polar aprotic solvents and in low boiling point common solvents. High quality polyimide films could be prepared by casting the polyimide solution on glass plate followed by thermal baking to remove the organic solvents and volatile completely. Experimental results indicated that the fluorinated polyimides exhibited good thermal stability with glass transition temperature ranged of 245-283 °C and temperature at 5% weight loss of 536-546 °C. Moreover, the polyimide films showed outstanding mechanical properties with the tensile strengths of 87.7-102.7 MPa and elongation at breaks of 5.0-7.8%, good dielectric properties with low dielectric constants of 2.71-2.97 and low dissipation factor in the range of 0.0013-0.0028.     

Synthesis and properties of novel soluble polyimides having a spirobisindane-linked dianhydride unit

A new synthetic procedure was elaborated allowing the preparation of semiaromatic dianhydride. N-Methyl protected 4-chlorophthalic anhydride was nitrated with HNO₃ to produce N-methyl-4-chloro-5-nitrophthalimide (1). The aromatic nucleophilic substitution reaction between 5,5′,6,6′-tetrahydroxy-3,3,3′,3′-tetramethyl-1,1-spirobisindane and 1 afforded spirobisindane-linked bis(N-methylphthalimide) (2), which was hydrolyzed and subsequently dehydrated to give the corresponding dianhydride (3). The latter was polymerized with five different aromatic diamines to afford a series of aromatic polyimides. The properties of polyimides such as inherent viscosity, solubility, UV transparency and thermal stability were investigated to illustrate the contribution of the introduction of spirobisindane groups into the polyimide backbone. The resulting polyimides were readily soluble in polar solvents such as chloroform, THF and N-methyl-2-pyrrolidone. The glass-transition temperatures of these polyimides were in the range of 254-292 °C. The tensile strength, elongation at break, and Young's modulus of the polyimide film were 68.8-106.6 MPa, 5.9-9.8%, 1.7-2.0 GPa, respectively. The polymer films were colorless and transparent with the absorption cutoff wavelength at 286-308 nm.     

Ortho alkyl substituents effect on solubility and thermal properties of fluorenyl cardo polyimides

Five fluorenyl cardo diamines containing different alkyl substituents were synthesized and characterized. A series of fluorenyl cardo polyimides were prepared by polycondensation of these cardo diamines with 4,4′-oxydiphthalic anhydride (ODPA), 3,3′,4,4′-benzophenonetetracarboxylic dianhydride (BTDA), 3,3′,4,4′-biphenyl tetracarboylic dianhydride (BPDA) and pyromellitic dianhydride (PMDA). Most of fluorenyl cardo polyimides exhibited excellent solubility in common organic solvents such as m-cresol, chloroform, tetrahydrofuran (THF), N-methyl-2-pyrrolidinone (NMP), N,N-dimethylacetamide (DMAC) etc. and intrinsic viscosity in N,N-dimethylacetamide (DMAC) ranged from 0.31 to 0.92 dl/g. T_g of polyimides based on ODPA decrease with the number and size of alkyl substituents on fluorenyl cardo diamine. The results show that the incorporation of noncoplanar structure led by the introducing alkyl substituents on fluorenyl cardo diamines improves the solubility of cardo polyimides in organic solvents without sacrificing thermal properties.     

Water resistant sulfonated polyimides based on 4,4′-binaphthyl-1,1′,8,8′-tetracarboxylic dianhydride (BNTDA) for proton exchange membranes

A series of sulfonated polyimides (SPIs) were synthesized in m-cresol from 4,4′-binaphthyl-1,1′,8,8′-tetracarboxylic dianhydride (BNTDA), 4,4′-diaminodiphenylether-2,2-disulfonicacid (ODADS), and 4,4′-diamino-diphenyl ether (ODA) in the presence of triethylamine and benzoic acid. The resulted polyimides showed much better water resistance than the corresponding sulfonated polyimides from 1,4,5,8-naphthalenetetracarboxylic dianhydride (NTDA) and ODADS, which is contributed to the higher electron density in the carbonyl carbon atoms of BNTDA. Copolyimides S-75 and S-50 maintained their mechanical properties and proton conductivities after aging in water at 100 °C for 800 h. The proton conductivity of these SPIs was 0.0250-0.3565 S/cm at 20 °C and 100% relative humidity (RH), and increased to 0.1149-0.9470 S/cm at 80 °C and 100% RH. The methanol permeability values of these SPIs were in the range of 0.99-2.36 × 10⁻⁷ cm²/s, which are much lower than that of Nafion 117 (2 × 10⁻⁶ cm²/s).     

Preparation and Properties of Cyano-Containing Polyimide Films Based on 2,6-Bis(4-aminophenoxy)- benzonitrile

Summary A series of cyano-containing polyimides were synthesized from 2,6-bis(4-amino- phenoxy)benzonitrile and some aromatic dianhydride monomers by solution polycondensation. The poly(amic acid) films could be obtained by solution-cast from N-methyl-2-pyrrolidinone solutions and thermally converted into tough polyimide films. Structure and physical properties of thin films of those polyimides were measured by FTIR, TGA, dynamic mechanical analysis and LCR hitester et al. Results showed that the polyimides prepared from 2,6-bis(4-aminophenoxy)- benzonitrile and 2,2-bis[4-(3,4-dicarboxyphenoxy)phenyl]propane dianhydride or 4,4’-(hexafluoropropylidene)diphthalic anhydride exhibited more excellent energy-damping characteristic and excellent solubility in NMP, DMF, DMAc, DMSO, THF and CHCl₃, whereas the polyimides from 2,6-bis(4-aminophenoxy)benzonitrile and 3,3’,4,4’-biphenyltetracarboxylic dianhydride or Pyromellitic dianhydride were insoluble in polar and nonpolar organic solvents. All polyimides indicated higher glass transition temperatures, excellent thermal stability and tensile properties. Incorporating a nitrile group into the polyimide backbone would enhance the dielectric constant of the polyimide films.     

Synthesis and characterization of polyimides and co-polyimides having pendant benzoic acid moiety

A novel diamine monomer, 2,4-diamino-4′-carboxy diphenyl ether had been synthesized. Several polyimides were prepared by reacting this diamine with commercially available dianhydrides, such as benzophenone tetracarboxylic acid dianhydride (BTDA), 4,4′-bis{hexafluoroisopropylidene bis (phthalic anhydride)}(6-FDA), oxydiphthalic anhydride (ODPA) and 3,3′,4,4′-biphenyltetracarboxylic acid dianhydride (BPDA). Furthermore, copolymers from the resulting diamine and oxydianiline (ODA) with 6 FDA were also synthesized. The inherent viscosities of the polymers were 0.42-0.67 dl g⁻¹. The polymers have good solubility in polar aprotic solvents, high thermal stability up to 410 °C in nitrogen and high glass transition temperatures (T_g) ranging from 260-330 °C. These polymers formed tough flexible films by solution casting.     

Synthesis and properties of polyimides from isomeric bis(dicarboxylphenylthio)diphenyl sulfone dianhydrides

4,4′-Bis(3,4-dicarboxyphenylthio)diphenyl sulfone dianhydride(4,4′-PTPSDA) and 4,4′-bis(2,3-dicarboxyphenylthio)diphenyl sulfone dianhydride(3,3′-PTPSDA) were synthesized from chlorophthalic anhydrides and bis(4-mercaptophenyl)sulfone. Their structures were determined via IR spectra, ¹H NMR and elemental analysis. A series of polyimides were prepared from isomeric PTPSDAs and aromatic diamines in 1-methyl-2-pyrrolidinone (NMP) via the conventional two-step method. Polyimides based on 4,4′-PTPSDA and 3,3′-PTPSDA have good solubility in polar aprotic solvents and phenols. The 5% weight-loss temperatures of isomeric polyimides were near 500 °C in N₂. DMTA and DSC analyses indicated that the glass-transition temperatures of polyimides from 3,3′-PTPSDA are higher than those of polyimides from 4,4′-PTPSDA. The wide-angle X-ray diffraction showed that all polyimides are amorphous. The polyimides from 3,3′-PTPSDA showed higher permeability but lower permselectivity compared with those from 4,4′-PTPSDA.     

Novel polyimides derived from 2,3,3′,4′-benzophenonetetracarboxylic dianhydride

A series of polyimides (PIs) based on 2,3,3′,4′-benzophenonetetracarboxylic dianhydride (2,3,3′,4′-BTDA) and 3,3′,4,4′-BTDA were prepared by the conventional two-step process. The properties of the 2,3,3′,4′-BTDA based polyimides were compared with those of polyimides prepared from 3,3′,4,4′-BTDA. It was found that PIs from 2,3,3′,4′-BTDA have higher glass transition temperature and better solubility without sacrificing their thermal properties. Furthermore the rheological properties of PMR-15 type polyimide resins based on 2,3,3′,4′-BTDA showed lower melt viscosity and wider melt flow region (flow window) compared with those from 3,3′,4,4′-BTDA. The structure-property relations resulted from isomerism were discussed.     

Organosoluble and optically transparent fluorine-containing polyimides based on 4,4′-bis(4-amino-2-trifluoromethylphenoxy)-3,3′,5,5′-tetramethylbiphenyl

A novel fluorinated diamine monomer, 4,4′-bis(4-amino-2-trifluoromethylphenoxy)-3,3′,5,5′-tetramethylbiphenyl, was prepared by a nucleophilic chloro-displacement reaction of 3,3′,5,5′-tetramethyl-4,4′-biphenol with 2-chloro-5-nitrobenzotrifluoride and subsequent reduction of the intermediate dinitro compound. The diamine was reacted with aromatic dianhydrides to form polyimides via a two-step polycondensation method; formation of poly(amic acid)s, followed by thermal imidization. All the resulting polyimides were readily soluble in many organic solvents and exhibited excellent film forming ability. The polyimides exhibited high T_g (312-351 °C), good thermal stability, and good mechanical properties. Low moisture absorptions (0.2-1.1 wt%), low dielectric constants (2.54-3.64 at 10 kHz), and low color intensity were also observed.     

Color lightness and highly organosoluble fluorinated polyamides, polyimides and poly(amide-imide)s based on noncoplanar 2,2′-dimethyl-4,4′-biphenylene units

A new diamine monomer containing noncoplanar methyl substitution, 2,2′-dimethyl-4,4′-bis(2-trifluoromethyl-4-aminophenoxy)biphenyl (DBTFAPB) was successfully synthesized and used in the preparation of a series of polyamides and polyimides by direct polycondensation with various aromatic dicarboxylic acids and tertacarboxylic dianhydrides. A new noncoplanar dicarboxylic acid monomer containing noncoplanar methyl substitution, 2,2′-dimethyl-4,4′-bis(2-trifluoromethyl-4-trimellitimidophenoxy)biphenyl (DBTFTPB) was also successfully synthesized by refluxing the diamine, DBTFAPB, with trimellitic anhydride in glacial acetic acid. A series of new poly(amide-imide)s were prepared directly from DBTFTPB with various diamines in N-methyl-2-pyrrolidinone (NMP). All the polymers exhibited excellent solubility in solvents, such as N-methyl-2-pyrrolidinone (NMP), N,N-dimethylacetamide (DMAc), N,N-dimethylformamide (DMF), dimethyl sulfoxide (DMSO), pyridine, tetrahydrofuran (THF), cyclohexanone and γ-butyrolactone at room temperature or upon heating at 70 °C. Inherent viscosities of the polymers were found to range between 0.60 and 1.34 dL g⁻¹. Gel permeation chromatography (GPC) of the polymers showed number-average and weight-average molecular weight up to 7.3×10⁴ and 17.9×10⁴, respectively. These polymers showed that the glass transition temperatures were between 230 and 265 °C, and the 10% mass loss temperatures were higher than 460 °C in nitrogen atmosphere. All the polymers could be cast into flexible and tough films from DMAc solutions. They had a tensile strength in the range of 82-124 MPa and a tensile modulus in the range of 1.9-2.9 GPa. These polymers exhibited low dielectric constants ranging from 2.87 to 4.03, low moisture absorption in the range of 0.29-3.20%, and high transparency with an ultraviolet-visible absorption cut-off wavelength in the 347-414 nm range.     

A unique crystallization and double melting behavior of a polyimide derived from 3,3′,4,4′-biphenyltetracarboxylic dianhydride and 1,4-bis(3-aminopropyl)piperazine

A unique crystallization and melting behavior of a novel semicrystalline polyimide derived from 3,3′,4,4′-biphenyltetracarboxylic dianhydride and 1,4-bis(3-aminopropyl)piperazine were studied by differential scanning calorimetry (DSC) with and without temperature modulation and wide-angle X-ray diffraction (WAXD). Polymer samples isolated from a chloroform solution showed melting transitions in the DSC. However, WAXD traces showed crystallinity only after annealing above the glass transition, for about 2 h. For samples crystallized from the melt, crystallization could be achieved only in a narrow crystallization range of 200-220 °C, after 10 h. A maximum crystallinity of this polyimide was found to be 30%. Two distinct melting transitions were observed by DSC, which could be explained using a partial disordering—reorganization—final melting model.     

Synthesis and characterization of novel polyimides derived from 2,6-bis[4-(3,4-dicarboxyphenoxy)benzoyl]pyridine dianhydride and aromatic diamines

A novel pyridine-containing aromatic dianhydride monomer, 2,6-bis[4-(3,4-dicarboxyphenoxy)benzoyl]pyridine dianhydride, was synthesized from the nitro displacement of 4-nitrophthalonitrile by the phenoxide ion of 2,6-bis(4-hydroxybenzoyl)pyridine, followed by acidic hydrolysis of the intermediate tetranitrile and cyclodehydration of the resulting tetraacid. A series of new polyimides holding pyridine moieties in main chain were prepared from the resulting dianhydride monomer with various aromatic diamines via a conventional two-stage process, i.e. ring-opening polycondensation forming the poly(amic acid)s and further thermal or chemical imidization forming polyimides. The inherent viscosities of the resulting polyimides were in the range of 0.51-0.68 dL/g, and most of them were soluble in aprotic amide solvents and cresols, such as N,N-dimethylacetamide, N-methyl-2-pyrrolidone, and m-cresol, etc. Meanwhile, some strong and flexible polyimide films were obtained, which have good thermal stability with the glass transition temperatures of 221-278 °C, the temperature at 5% weight loss of 512-540 °C, and the residue at 800 °C of 60.4-65.3% in nitrogen, as well as have outstanding mechanical properties with the tensile strengths of 72.8-104.4 MPa and elongations at breakage of 9.1-11.7%. The polyimides also were found to possess low dielectric constants.     

Synthesis and properties of novel organosoluble polyimides derived from 1,4-bis[4-(3,4-dicarboxylphenoxy)]triptycene dianhydride and various aromatic diamines

A novel triptycene-based dianhydride, 1,4-bis[4-(3,4-dicarboxylphenoxy)]triptycene dianhydride, was prepared from 4-nitro-N-methylphthalimide and potassium phenolate of 1,4-dihydroxytriptycene (1). The aromatic nucleophilic substitution reaction between 4-nitro-N-methylphthalimide and 1 afforded triptycene-based bis(N-methylphthalimide) (2), which hydrolyzed and subsequently dehydrated to give the corresponding dianhydride (3). A series of new polyimides containing triptycene moieties were prepared from the dianhydride monomer (3) and various diamines in m-cresol via conventional one-step polycondensation method. Most of the resulting polyimides were soluble in common organic solvents, such as chloroform, THF, DMAc and DMSO. The polyimides exhibited excellent thermal and thermo-oxidative stabilities with the onset decomposition temperature and 10% weight loss temperature ranging from 448 to 486 °C and 526 to 565 °C in nitrogen atmosphere, respectively. The glass transition temperatures of the polyimides were in the range of 221-296 °C. The polyimide films were found to be transparent, flexible, and tough. The films had tensile strengths, elongations at break, and tensile moduli in the ranges 95-118 MPa, 5.3-16.2%, and 1.03-1.38 GPa, respectively. Wide-angle X-ray diffraction measurements revealed that these polyimides were amorphous.     

Copolyimides from 2,3,3′,4′-biphenyltetracarboxylic dianhydride and pyromellitic dianhydride with 4,4′-oxydianiline

A series of copolyimides were prepared via the polyamide acids (polyamic acids) from the reaction of 2,3,3′,4′-biphenyltetracarboxylic dianhydride (a-BPDA) and pyromellitic dianhydride (PMDA) with 4,4′-oxydianiline (4,4′-ODA) at dianhydride molar ratios of 9:1, 7:3, 1:1, 3:7 and 1:9. Homopolymers and a 1:1 polymer blend were also prepared. Films from the 7:3, 1:1 and 3:7 molar ratio polyamide acids reacted for 5-6 h at ambient temperature were brittle, whereas films from the same polyamide acids reacted for 24-48 h at ambient temperature were fingernail creaseable. The difference was apparently due to the initial formation of incompatible block domains that underway randomization upon longer reaction time. The differential scanning calorimetric (DSC) curves of some of the brittle films quenched after heating to 400 °C had two apparent glass transition temperatures (T_gs), indicative of two block domains. The creaseable films quenched after heating to 400 °C had single T_gs. Wide-angle X-ray diffraction showed all films to be amorphous even though the initial DSC curves showed strong endothermic peaks, generally associated with crystalline melts. These strong endotherms near the T_g region were thought to be due to relaxation of regions in the highly stressed films. Films of copolyamide acids from the reaction of 1:1 molar ratios of 3,3′,4,4′-oxydiphthalic anhydride/a-BPDA and 3,3′,4,4′-biphenyltetracarboxylic dianhydride/a-BPDA with 4,4′-ODA reacted for 6 h were fingernail creaseable. The chemistry and the properties of the copolymers are compared with those of the homopolymers.     

Colorless polyimides from 2,3,3′,4′-biphenyltetracarboxylic dianhydride (α-BPDA) and various aromatic bis(ether amine)s bearing pendent trifluoromethyl groups

A series of organosoluble and light-colored polyimides (III) was prepared from 2,3,3′,4′-biphenyltetracarboxylic dianhydride (α-BPDA) with various fluorinated aromatic bis(ether amine)s via two-step method with thermal or chemical imidization of poly(amic acid)s yielded polyimides. The III series had inherent viscosity of 0.74-1.01 dl/g and showed excellent solubility in a variety of organic solvents. They were soluble in the amide polar solvent, ether-type solvent, and chlorinated solvent. These polyimide films also showed a high optical transparency and less color intensity, with an ultraviolet-visible absorption edge of 369-382 nm and low b^* values (a yellowness index) of 5.0-11.7. Glass-transition temperature of the III series was recorded at 244-319 °C and higher than the isomeric polyimides V series. Compared with the nonfluorinated polyimides IV, the III series showed lighter-colored and lower dielectric constants and moisture absorptions. The good tensile properties and excellent thermal properties of the III series were also observed.     

Morphology control of various aromatic polyimides by using phase separation during polymerization

Morphology control of various aromatic polyimides representative as poly(4,4′-oxydiphenylene pyromelliteimide) was examined by using the phase separation during solution polymerization. Polymerizations of aromatic dianhydrides and aromatic diamines to the polyimides were carried out in poor solvents at 240-330 °C for 6 h with no stirring. Polymerization concentrations were from 0.25% to 3.0%. The polyimides were obtained as yellow precipitates. Two categorized morphologies were created, which were particles and crystals exhibiting lath-like and plate-like habits. These morphologies of polyimides could be selectively controlled by the polymerization conditions. The higher concentrations, less miscible solvents and lower temperatures were preferable to yield the particles via liquid-liquid phase separation. On the contrary, the lower concentration, miscible solvents and higher temperature were desirable to yield the crystals. The polyimide precipitates showed high crystallinity and possessed excellent thermal stability at which the 10 wt% loss temperatures in N₂ were in the range of 590-694 °C.     

Novel soluble polyimides derived from 2,2′-bis[4-(5-amino-2-pyridinoxy)phenyl]hexafluoropropane: Preparation,characterization, and optical,dielectric properties

Two novel aromatic diamine monomer, 2,2′-bis[4-(5-amino-2-pyridinoxy)phenyl] hexafluoropropane (6FBAPDP) and 2,2′-bis[4-(5-amino-2-pyridinoxy)phenyl] propane (BAPDP), were successfully synthesized. Aimed at clarifying the structure-property relationships of pyridine-containing high-performance polymers, a series of novel fluorinated polyimides PI-(1–4) were prepared from 6FBAPDP with various commercially aromatic anhydrides, and polyimide (PI-5) was synthesized derived from BAPDP and 2,2′-bis(3,4-dicarboxyphenyl) hexafluoropropane dianhydride (6FDA) via a two-stage process with heating imidization method. The fluorinated polyimides PI-(1–4) exhibited good solubility in strong polar solvents, such as N, N-dimethylacetamide, N, N-dimethylformamide, N-methyl-2-pyrrolidone, dimethyl sulfoxide, m-cresol, and could afford flexible, tough and transparent films with an UV–visible absorption cut-off wavelength at 342–393 nm. The glass transition temperatures of these polyimides were recorded between 239 and 306 °C by differential scanning calorimetry, and the 5% weight loss occurred at temperatures above 498 and 490 °C, in nitrogen and air, respectively. The polyimide films had the in-plane coefficients of thermal expansion (CTE) that ranged from 54 to 74 ppm °C⁻¹. Moreover, the fluorinated polyimide films showed low moisture absorptions of 0.51–0.82% and outstanding mechanical properties with the tensile strengths of 75–100 MPa, tensile moduli of 3.2–4.0 GPa and elongation at break of 5.5–10.3%, good dielectric properties with low dielectric constants of 2.71–2.92 at 1 MHz.     

Properties of organosoluble aromatic polyimides from 3′-trifluoromethyl-3,4′-oxydianiline

A colorless fluorinated diamine, 3′-trifluoromethyl-3,4′-oxydianiline (3′-CF₃-3,4′-ODA) (II) was prepared through the nucleophilic substitution reaction of 3-nitrophenol and 2-chloro-5-nitrobenzotrifluoride by catalytic reduction with hydrazine and Pd/C. A series of Polyimides V were synthesized from the diamine II with various aromatic dianhydrides III_a-f via thermal and chemical imidization. These polyimides had inherent viscosities ranging from 0.88 to 1.12 dl/g. A comparison of V, VI to analogous polyimides VII, VIII. VI, VII and VIII was based on 3′4-ODA, 3-CF₃-4,4′-ODA, 4,4′-ODA, respectively. In terms of the color of PI revealed that the color intensity of phenoxy-containing amine of the meta-structure and the para-structure with the CF₃ group would fell off color intensity. The color intensity of the four polyimide series was lessened in the following order: V>VII>VI>VIII. The solubility of V is better than VI, VII and VII. The polyimide V films had a tensile strength ranging from 124 to 147 MPa, elongation at break from 9 to 65%, and initial modulus from 2.3 to 2.8 GPa. The glass transition temperature of polymers was recorded at 234-313 °C. They had 10% weight loss at a temperature above 515 °C and left more than 50% residue even at 800 °C in nitrogen. Compared with polyimides VI, V showed the lower dielectric constants of 2.80-3.50 (40 MHz), and moisture absorptions in the range of 0.44-1.02 wt%.