Synthesis,characterization, and properties of novel fluorine containing aromatic polyamides

A series of novel fluorine containing aromatic polyamides were synthesized by the direct polycondensation of various fluorine containing aromatic diamines and commercially available 5‐t‐butyl isophthalic acid. These polyamides have good solubility in several organic solvents such as dimethylformamide, N,N‐dimethylacetamide, 1‐Methyl‐2‐pyrrolidone, dimethyl sulfoxide, and tetrahydrofuran. The synthesized polymers exhibited inherent viscosities up to 0.93 dL/g and M_w up to 1,52,000 with PDI of 2.49. The polyamides exhibited good thermal stability up to 489°C for 10% weight loss in nitrogen and high glass transition temperature up to 273°C. Dynamic mechanical analysis showed a very good retention of storage modulus up to the glass transition temperature. The tan δ peak value at 1 Hz was used to calculate the T_g and these values are in good agreement with differential scanning calorimetry data. The polyamide films were flexible with tensile strength up to 72 MPa, elongations at break up to 14%, and modulus of elasticity up to 1.39 GPa depending on the exact repeating unit structure. X‐ray diffraction measurements indicate that these polyamides are semicrystalline. Rheology study showed same trend of melt viscosity behavior with different shear rate for all polymers. Water absorption study indicates the hydrophobic nature of the polymer. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Synthesis,characterization, and properties of novel polyetherester polyols and developed polyurethanes

Three kinds of cyclic anhydrides, which stand for aliphatic anhydride, aromatic anhydride, and anhydride containing double bond: succinic anhydride, phthalic anhydride, and maleic anhydride have been copolymerized with propylene oxide and low molecular weight polyoxypropylenediol via ring‐opening copolymerization initiator by double metal cyanide complex catalyst to synthesis a series of polyetherester (PEE) polyols. The structure of the obtained copolymers was confirmed by several analysis methods. Three kinds of polyetherester polyurethane (PEEPU) were thus synthesized by polymerization of as‐synthesized PEE polyol with 4,4′‐diphenylmethane diisocyanate. The mechanical properties of the obtained PEEPU were tested. The results showed that the mechanical properties of three polyurethanes are different based on their structure and composition. The inducing of the rigid phenyl group in the soft segment can improve the mechanical strength remarkably. The influences of ester content in soft segment and the hard segment content on the mechanical properties of PEEPU were studied. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 417–424, 2007     

Conjugated rod-coil block copolymers: Synthesis, morphology, photophysical properties, and stimuli-responsive applications

Conjugated rod-coil block copolymers have been accorded great importance since they provide a powerful route towards supramolecular objects with novel architectures, functions and physical properties. This review summarizes recent progress on the synthesis, morphology, optoelectronic properties and applications of such block copolymers. The combination of the precise condensation and living polymerization through the grafting-from or grafting-onto methodology produce various architectures of conjugated rod-coil block copolymers, including rod-coil, coil-rod-coil, rod-coil-coil, and rod-coil-rod. In the following, the relationships between polymer morphologies and photophysical properties in different phases are reviewed, as classified by solution micelles, thin films or bulk samples, polymer brushes and electrospun nanofibers. The effects of the rod/coil ratio and polymer architecture on the morphology and optoelectronic properties are discussed. The control of nanosize domain and the aligned direction of conjugated rods are the key issues for enhancing the optoelectronic device performance. Moreover, novel multifunctional sensory materials based on combining the tunable photophysical properties of the π-conjugated rod and the stimuli-responsive coil are also highlighted. It is believed that conjugated rod-coil block copolymers could spark the future evolution of nanostructured polymers for multifunctional device applications.     

RAFT polymerization of temperature- and salt-responsive block copolymers as reversible hydrogels

Reversible-addition fragmentation chain transfer (RAFT) polymerization enabled the synthesis of novel, stimuli-responsive, AB and ABA block copolymers. The B block contained oligo(ethylene glycol) methyl ether methacrylate (OEG) and was permanently hydrophilic in the conditions examined. The A block consisted of diethylene glycol methyl ether methacrylate (DEG) and [2-(methacryloyloxy)ethyl]trimethylammonium chloride (TMA). The A block displayed both salt- and temperature-response with lower critical solution temperatures (LCSTs) dependent on the molar content of TMA and the presence of salt. Higher TMA content in the AB diblock copolymers increased the critical micelle temperatures (CMT) in HPLC-grade water due to an increased hydrophilicity of the A block. Upon addition of 0.9 wt% NaCl, the CMTs of poly(OEG-b-DEG₉₅TMA₅) decreased from 50 °C to 36 °C due to screening of electrostatic repulsion between the TMA units. ABA triblock copolymers displayed excellent hydrogel properties with salt- and temperature-dependent gel points. TMA incorporation in the A block increased the gel points for all triblock copolymers, and salt-response increased with higher TMA composition in the A block. For example, poly(DEG₉₈TMA₂-b-OEG-b-DEG₉₈TMA₂) formed a hydrogel at 40 °C in HPLC-grade water and 26 °C in 0.9 wt% NaCl aqueous solution. These salt- and temperature-responsive AB diblock and ABA triblock copolymers find applications as drug delivery vehicles, adhesives, and hydrogels.     

Synthesis,characterization, and comparison of properties of novel fluorinated poly(imide siloxane) copolymers

Four new poly(imide siloxane) copolymers were prepared by a one‐pot solution imidization method at a reaction temperature of 180°C in ortho‐dichlorobenzene as a solvent. The polymers were made through the reaction of o‐diphthaleic anhydride with four different diamines—4,4′‐bis(p‐aminophenoxy‐3,3″‐trifluoromethyl) terphenyl, 4,4′‐bis(3″‐trifluoromethyl‐p‐aminobiphenyl ether)biphenyl, 2,6‐bis(3′‐trifluoromethyl‐p‐aminobiphenyl ether)pyridine, and 2,5‐bis(3′‐trifluoromethyl‐p‐aminobiphenylether)thiopene—and aminopropyl‐terminated poly dimethylsiloxane as a comonomer. The polymers were named 1a , 1b , 1c , and 1d , respectively. The synthesized polymers showed good solubility in different organic solvents. The resulting polymers were well characterized with gel permeation chromatography, IR, and NMR techniques. ¹H‐NMR indicated that the siloxane loading was about 36%, although 40 wt % was attempted. ²⁹Si‐NMR confirmed that the low siloxane incorporation was due to a disproportionation reaction of the siloxane chain that resulted in a lowering of the siloxane block length. The films of these polymers showed low water absorption of 0.02% and a low dielectric constant of 2.38 at 1 MHz. These polyimides showed good thermal stability with decomposition temperatures (5% weight loss) up to 460°C in nitrogen. Transparent, thin films of these poly(imide siloxane)s exhibited tensile strengths up to 30 MPa and elongations at break up to 103%, which depended on the structure of the repeating unit. The rheological properties showed ease of processability for these polymers with no change in the melt viscosity with the temperature. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Synthesis,characterization, and properties of novel poly(ether urea)s

Two diamines, 2,6‐bis(4‐aminophenoxy)pyridine and 2,6‐bis(5‐amino‐1‐naphenoxy)pyridine, were prepared through the nucleophilic aromatic substitution reaction of 4‐aminophenol and 5‐amino‐1‐naphthol, respectively, with 2,6‐dichloropyridine. Poly(ether urea)s were synthesized through the polyaddition reactions of these diamines with aromatic, semiaromatic, and cycloaliphatic diisocyanates. All the monomers and polymers were fully characterized, and physical properties of the polymers, including the thermal behavior, thermal stability, solubility, and solution viscosity, were studied. The polyureas showed improved thermal stability. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 961–965, 2004     

Synthesis,characterization, and mechanical properties of a novel terphenyl liquid crystalline epoxy resin

A novel terphenyl liquid crystalline (LC) epoxy resin was synthesized and characterized by ¹H‐NMR, Fourier transform infrared spectroscopy, differential scanning calorimetry (DSC), and polarizing optical microscopy. Depending on the curing temperature, the synthesized resin formed both smectic and nematic LC phases. A time‐temperature‐transformation diagram was constructed to optimize the curing process, which helped in the preparation of LC and isotropic system. The terphenyl epoxy resin obtained exhibited higher acid resistance than a comparable Schiff‐base epoxy resin, and also displayed excellent fracture toughness. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41296.     

Synthesis and characterization of novel dihydrobenzoxazine resins

Three dihydrobenzoxazines are synthesized from bisphenol A (BPA), 4,4′‐biphenol (BIP), and dicyclopentadiene phenol adduct (DCPD). Polydihydrobenzoxazine containing 4,4′‐biphenol (BIPDB) had the most rigid structure of the three and was found to possess the best mechanical and thermal properties. The glass transition temperature of BIPDB was 206°C, and that of BPA‐type polydihydrobenzoxazine (BPADB) and dicyclopentadiene type polydihydrobenzoxazine (DCPDDB) were 184 and 183°C, respectively. DCPDDB, with a rigid hydrophobic cycloaliphatic structure, was found to possess excellent properties such as low moisture absorption, low dielectric constant, low polarization. The resulted polymer from DCPDDB had a dielectric constant of 2.94U, which was better than that of polymers derived from BPA (3.31U), BIP (3.45U), and traditional phenolic resin (3.9–4.0U). © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 342–347, 2006     

Synthesis,characterization, and properties of a polyhedral oligomeric octadiphenylsulfonylsilsesquioxane

A novel polyhedral oligomeric octadiphenylsulfonylsilsesquioxane (ODPSS) was synthesized from octaphenylsilsesquioxane and benzenesulfonyl chloride via a Friedel–Crafts reaction with a high yield. ODPSS was identified by Fourier transform infrared spectroscopy, ¹H‐NMR, ¹³C‐NMR, ²⁹Si‐NMR, matrix‐assisted laser desorption/ionization time‐of‐flight mass spectrometry (MALDI–TOF MS), wide‐angle X‐ray diffraction, and elemental analysis to be a kind of polyhedral oligomeric silsesquioxane of a T₈R₈ structure. ODPSS exhibited superior thermal stability according to thermogravimetric analysis. Its initial thermal decomposition temperature (T_onset) was at 491°C in air and 515°C in nitrogen. Thermal and mechanical properties of epoxy resin (EP) composites with ODPSS added were studied by differential scanning calorimetry and tensile testing. The results show that the incorporation of ODPSS at a low loading content not only improved the glass‐transition temperature of the EP composites but also enhanced their tensile strength. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40892.     

Synthesis,characterization and thermal properties of novel epoxy/expandable graphite composites

Epoxy resins are widely used as coatings, adhesives and primers and in semiconductor encapsulation. A requirement that has recently gained importance is that of flame resistance, and imparting flame retardancy to epoxy resins has attracted much attention. Expandable graphite (EG) can improve flame‐retardant properties of polymers. Due to poor compatibility between polymer matrix and EG, flame‐retardant performance will be impaired. EG can be functionalized using a coupling agent. This gives rise to covalent bonding between organic and inorganic phases. This will improve the compatibility between filler and polymer to enhance the thermal stability of composites. X‐ray photoelectron spectroscopy was used to characterize the functionalizing reaction between coupling agent and EG. Thermogravimetric analysis (TGA) and integral procedural decomposition temperature (IPDT) were used to calculate the thermal stability of composites. The results show that functionalized EG can improve the thermal stability of the composites. TGA/mass spectroscopy (MS) shows that the amount of toxic gases liberated from the composites is less than that from pure epoxy. Novel epoxy/EG composites were prepared successfully via the sol–gel method. The results of TGA, IPDT and TGA/MS showed that functionalized EG can enhance the thermal stability of composites and can suppress the production of toxic gases. The composite materials could provide a safer choice. Copyright © 2009 Society of Chemical Industry     

Synthesis,characterization, and properties of a novel epoxy resin containing both binaphthyl and biphenyl moieties

A new epoxy resin containing both binaphthyl and biphenyl moieties in the skeleton (BLBPE) was synthesized and confirmed by electrospray ionization mass spectroscopy, ¹H‐nuclear magnetic resonance spectroscopy, and infrared spectroscopy. To evaluate the combined influence of two moieties, one epoxy resin containing binaphthyl moiety and another containing biphenyl moiety were also synthesized, and a commercial biphenyl‐type epoxy resin (CER3000L) was introduced. Thermal properties of their cured polymers with phenol p‐xylene resins were characterized by differential scanning calorimetry, dynamic mechanical, and thermogravimetric analyses. The cured polymer obtained from BLBPE showed remarkably higher glass transition temperature and lower moisture absorption, as well as comprehensively excellent thermal stability. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Synthesis and characterization of novel polyesterimides

A series of soluble novel polyesterimides was synthesized from diamines [a mixture of 2,2‐bis(4‐(4‐aminophenoxy)phenyl)propane (BAPP) with amine‐terminated polysiloxane (ATPS) in various mole ratios] and the ester‐group‐containing dianhydrides. The ester group containing dianhydrides in turn was synthesized by the transesterification reaction of trimellitic anhydride (TMA) with diacetate ester of hydroquinone (HQ), 4,4′‐dihydrophenyl (BP), 1,6‐hexanediol, or ethylene glycol. The resulted polyesterimides were characterized by using Fourier‐transform infrared spectroscopy, inherent viscosity, solubility, differential scanning calorimetry (DSC), and thermogravimetric analysis (TGA). The polyesterimides of BP and HQ had relatively high glass transition temperatures in the range of 214.7–227.2 and 195.7–210.5°C, respectively. The glass transitions decreased rather slowly with the increase in polysiloxane content. Thermal stability and the weight‐loss behavior of polyesterimides were studied by TGA. All polyesterimides of BP and HQ (BPI and HQI) showed no significant weight loss below 500°C in a N₂ environment, and the decomposition temperatures (T_d5%) of BPI and HQI were >520°C. Most polyesterimides were soluble in polar aprotic solvents and m‐cresol. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 730–738, 2004     

Synthesis,characterization, and properties of new siloxane grafted copolyimides

Three new siloxane containing grafted copolyimides have been prepared by one‐pot solution imidization technique. The polymers are made by the reaction of 4,4′‐(4,4′‐isopropylidenediphenoxy)bis(phthalic anhydride) (BPADA) with commercially available diamine 4,4′‐oxydianiline (ODA) with variation of silicon containing diamine, namely 3,5‐diaminobenzoate terminated polydimethylsiloxane (DBPDMS), as a comonomer to 10, 20, and 30 wt %. The films of the polymers were prepared by casting the polymer solution in dichloromethane. The polymers have been well‐characterized by GPC, IR, and NMR techniques. Thermal stabilities and decomposition behavior of the copolyimides were studied by DSC and TGA. The water contact angle values of the films indicate hydrophobic nature of the polymers. Thermal, flame retardant, mechanical, and surface properties of these polymers have been compared with the homopolyimide and with polyimides where polysiloxane is incorporated in the main chain. DSC revealed melting of the grafted siloxane chain at sub‐ambient temperature and a glass transition corresponding to the main polymer chain above 200°C. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Synthesis, characterization, and properties of novel phenylene-silazane-acetylene polymers

New phenylene-silazane-acetylene polymers, P1 and P2, have been synthesized using Sonogashira cross-coupling reactions with a new designed ethynyl-ended silylenediamine, N,N′-bis(4-ethynylphenyl)-1,1-diphenylsilylenediamine (1), as the key monomer. This also represents the first example that construction of polymers containing silazane unit with Sonogashira coupling reaction. The structures of monomer and polymers were well characterized. Their thermal properties were studied by differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). Both polymers had good thermal stability with their temperatures at 5% weight loss (T_d5) being higher than 394 °C under nitrogen and higher than 385 °C in air, respectively. Their char yields at 1000 °C under N₂ were above 70%. The fundamental photophysical properties in solution were also investigated. Both polymers showed fluorescence in ultraviolet region with moderate quantum yields. These polymers had potential to be used as high-temperature resistant resins and light-emitting materials with good thermal stability.     

Polyimides 6: Synthesis,characterization, and comparison of properties of novel fluorinated poly(ether imides)

Five new poly(ether imides) have been prepared on reaction with oxydiphthalic anhydride (ODA) with five different diamines: 1,4‐bis(p‐aminophenoxy‐2′‐trifluoromethyl benzyl) benzene, 4,4′‐bis(p‐aminophenoxy‐2′‐trifluoromethyl benzyl) benzene, 1,3‐bis(p‐aminophenoxy‐2′‐trifluoromethyl benzyl) benzene, 2,6‐bis(p‐aminophenoxy‐2′‐trifluoromethyl benzyl) pyridine, and 2,5‐bis(p‐aminophenoxy‐2′‐trifluoromethyl benzyl) thiophene. Synthesized polymers showed good solubility in different organic solvents. The polyimide films have low water absorption of 0.3–0.7%, low dielectric constants of 2.82–3.19 at 1 MHz, and high optical transparency at 500 nm (>73%). These polyimides showed very high thermal stability with decomposition temperatures (5% weight loss) up to 531°C in air and good isothermal stability; only 0.4% weight loss occurred at 315°C after 5 h. Transparent thin films of these polyimides exhibited tensile strength up to 147 MPa, a modulus of elasticity up to 2.51 GPa and elongation at break up to 30% depending upon the repeating unit structure. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 821–832, 2004     

Polyimides 7: Synthesis,characterization, and properties of novel soluble semifluorinated poly(ether imide)s

Three novel diamine monomers ( VI , VII , and VIII ) were synthesized. These diamine monomers lead to a number of semifluorinated poly(ether imide)s when reacted with different commercially available dianhydrides like pyromellitic dianhydride (PMDA), benzophenone tetracarboxylic acid dianhydride (BTDA), 2,2‐bis (3,4‐dicarboxyphenyl) hexafluoropropene (6FDA), and oxydiphthalic dianhydride (ODA) by thermal imidization route. Elemental analyses, IR and NMR techniques were used to characterize the monomers and polymers. The resulting polymers exhibited weight average molar masses up to 1.78 × 10⁵ g mol^?1 in GPC with respect to polystyrene standard and have very good solubility in several organic solvents such as NMP, DMF, DMAC, DMSO, chloroform, and THF. Very good solubility of these polymers in CDCl₃ enables their complete characterization by proton as well as ¹³C‐NMR techniques. The polymers showed very high thermal stability with decomposition temperature (5% weight loss) up to 511°C in air and high glass transition temperature up to 311°C depending upon the exact repeating unit structure. The polymer films showed high modulus (up to 2.9 GPa) as was evaluated by DMA. The polymers also showed very low water absorption (0.16%), low dielectric constant (2.35 at 1MHz) and very good optical transmission. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 3025–3044, 2007     

十一钨铜杂多钨硅酸盐位置异构体的合成、表征及性质

合成了通式为α-,βi-KnH6-n[SiW11Cu(H2O)O39].xH2O(βi=β1,β2,β3)的4种异构体,通过元素分析、IR光谱、UV光谱、极谱和循环伏安进行了表征。系统研究了它们在溶液中的电化学性质,提出了其还原机理,讨论了杂多酸阴离子的结构对其氧化还原性的影响,得出杂多阴离子的极谱半波电位顺序为β2>β1>β3>α,其还原过程包括铜的单电子还原和钨的双电子两质子加合过程。催化活性实验表明,合成化合物对烯烃环氧化反应具有良好的催化作用。     

Carbon nanofibers: Synthesis, characterization, and electrochemical properties

Carbon nanofibers (CNFs) have been synthesized by co-catalyst deoxidization process by a reaction between C₂H₅OC₂H₅, Zn and Fe powder at 650 °C for 10 h. These nanofibers exhibit diameters of ∼80 nm and lengths ranging from several micrometers to tens of micrometers. X-ray diffraction, Raman spectroscopy, and high-resolution transmission electron microscopy indicate that as-prepared CNFs possess low graphitic crystallinity. The resultant CNFs as electrode shows capacity of ∼220 mAh/g and high reversibility with little hysteresis in the insertion/deintercalation reactions of lithium-ion. In addition, the possible growth of CNFs is discussed.     

Synthesis and characterization of new injectable and degradable dextran-based hydrogels

Injectable and degradable hydrogels are very interesting networks for drug delivery and cell transplantation applications since they can be administered in the human body in a minimally invasive way. In most cases, the crosslinking reaction occurs by photopolymerisation or free radical polymerisation; however, the use of chemical initiators may promote cell death. In the current work, injectable and degradable dextran-based hydrogels were prepared without the use of initiators. Dextran, a natural glucose-containing polysaccharide, was oxidized with sodium periodate (dexOx) and the derivatives characterized by NMR and FTIR spectroscopy's as well as by colorimetric techniques. The oxidized derivatives were crosslinked with adipic acid dihydrazide (AAD), forming a gel within 2-4 min. The obtained hydrogels were characterized by their mechanical properties, swelling and degradation behavior under physiologic conditions. In addition, the hydrogel interior morphology as well as porous structure was evaluated by scanning electron microscopy (SEM) and mercury intrusion porosimetry (MIP). MIP analysis showed that dexOx hydrogels crosslinked with 10% of AAD were macroporous with pore sizes ranging from 0.32 to 0.08 μm. As expected, the average pore size increased during hydrogel degradation as confirmed by SEM and MIP studies.     

Synthesis and characterization of novel fluorinated azopolyamides

Summary  Novel soluble fluorinated azopolyamides 4a-d were synthesized by reacting 2-trifluoromethyl-4,4’-diaminodiphenyl ether 2 with various azodibenzoyl chlorides 3a-d using the low temperature solution polycondensation technique. The fluorinated diamine 2 was prepared through the nucleophilic substitution reaction of 4-nitrophenol and 2-chloro-5-nitrobenzotrifluoride via catalytic reduction catalytic reduction with hydrazine and Pd/C. All of the fluorinated azopolyamides exhibited excellent solubility at room temperature in strong polar solvents such as N,N-dimethylacetamide (DMAc), N,N-dimethylformamide (DMF), dimethyl sulfoxide (DMSO) and N-methyl-pyrrolidinone (NMP). Inherent viscosities of the azopolyamides were found to range from 0.85 to 1.35 dl/g, and those azopolyamides could be cast into flexible and tough films from DMAc solutions. The azopolyamides showed that the glass transition temperatures (T_g) were between 231 and 259^oC, and the char yields of all the azopolyamides except for 4d at 800^oC in nitrogen atmosphere were above 47%. Furthermore, all the azopolyamides exhibited thermal and photochromic properties.