The effect of polystyrene-block-poly(4-vinylpyridine) prepared by a RAFT method in the dispersion polymerization of MMA

The dispersion polymerization of methyl methacrylate (MMA) has been carried out using polystyrene-block-poly(4-vinylpyridine) copolymer [P(S-b-4VP)], which was prepared by a reversible addition-fragmentation chain transfer (RAFT) method, as a steric stabilizer in an alcohol media. The stable polymer particles were obtained when the block copolymer concentrations increased from 1 to 10 wt% relative to the monomer and the average particle sizes decreased from 5.3 to 3.4 μm with the increasing concentration of the block copolymer. In particular, the incorporation of 2 wt% polystyrene-block-poly(4-vinylpyridine) produced 4.3 μm of monodisperse PMMA particles with 2.14% of C_v. Thus, the P(S-b-4VP) block copolymer prepared by the RAFT method is working not only as a steric stabilizer, but also in providing monodisperse micron-sized PMMA particles.     

Phase continuity and inversion in polystyrene/poly(methyl methacrylate) blends

Dual-phase continuity and phase inversion of polystyrene (PS)/poly(methyl methacrylate) (PMMA) blends processed in a twin-screw extruder was investigated using a selective extraction technique and scanning electron microscopy. Emphasis was placed on investigating the effects of viscosity ratio, blend composition, processing variables (mixing time and annealing) and diblock copolymer addition on the formation of bi-continuous phase structure (BPS) in PS/PMMA blends. The experimental results were compared with the volume fraction of phase inversion calculated with various semi-empirical models. The results showed that the formation of a BPS strongly depends on the blend composition and the viscosity ratio of the constituent components. Furthermore, BPS was found in a wide volume fraction interval. Increasing the mixing time and the addition of diblock copolymer, both led to a narrowing range of volume fraction in which BPS exists. Quiescent annealing coarsened the structure but indicated no qualitative changes. Some model predictions for phase inversion could predict qualitative aspects of the observed windows of co-continuity but none of the models could account quantitatively for the observed data.     

聚苯乙烯-聚甲基丙烯酸甲酯核-壳粒子的制备

由种子乳液聚合法制备了聚苯乙烯-聚甲基丙烯酸甲酯核-壳粒子。以过硫酸钾(KPS)为引发剂,辛基酚聚氧乙烯醚(OP-10)为乳化剂,合成了聚苯乙烯(PS)种子核;连续滴加甲基丙烯酸甲酯(MMA),在核表面富集MMA,制备了粒径范围在0.16~0.67μm的核-壳粒子;当单体苯乙烯与甲基丙烯酸甲酯(St/MMA)的比为30∶70(质量比)时,所得粒径在0.18μm,粒径分布为0.012。差示扫描量热(DSC)研究显示,复合粒子的玻璃化转变温度(Tg)为97.2℃,峰形单一,表现出良好的热性能。     

Association behavior of poly(methyl methacrylate-b-methacrylic acid-b-methyl methacrylate) in aqueous medium

ABA type triblock amphiphilic polyelectrolyte consisting of poly(methyl methacrylate-block-methacrylic acid-block-methyl methacrylate) (P(MMA-b-MAA-b-MMA)) was synthesized by atom transfer radical polymerization technique and the self-assembly behavior of the polymers in aqueous solution was studied over the course of neutralization. Combination of potentiometric and conductometric titrations along with dynamic light scattering techniques were used to investigate the size and shape of aggregates at various degrees of neutralization. The effect of hydrophobic-hydrophilic (MMA-MAA) ratio and polymer chain length on the aggregation behavior during neutralization was studied. P(MMA-b-MAA-b-MMA) with longer MMA segment self-assembles via the closed association mechanism through stronger self-entanglement of MMA chains, whereas P(MMA-b-MAA-b-MMA) with shorter MMA chain self-assembles via the open association mechanism, as confirmed by transmission electron microscopy. Conductometric titration was used to determine the counterion condensation during the course of neutralization. When the charge density of micelle approaches a critical value as neutralization progresses, counterion condensation of Na⁺ ions on the polymer chains occurs. The effect of counterion condensation on the aggregation behavior during neutralization was elucidated.     

Nanostructured thermosets from epoxy and poly(2,2,2-trifluoroethyl acrylate)-block-poly(glycidyl methacrylate) diblock copolymer: Demixing of reactive blocks and thermomechanical properties

Poly(2,2,2-trifluoroethyl acrylate)-block-poly(glycidyl methacrylate) (PTFEA-b-PGMA) diblock copolymer was synthesized via sequential reversible addition-fragmentation chain transfer (RAFT) polymerization. The reactive diblock copolymer was incorporated into epoxy to obtain the nanostructured thermosets. The morphology of the thermosets was investigated by means of atomic force microscopy (AFM) and small-angle X-ray scattering (SAXS). It is identified that the demixing of the reactive subchain (viz. PGMA) out of epoxy matrix occurred in the process of curing reaction, which exerted a profound impact on the glass transition temperatures of the nanostructured thermosets. The static contact angle measurements showed that the nanostructured thermosets displayed a significant enhancement in surface hydrophobicity as well as a reduction in surface free energy. The improvement in surface properties was attributed to the enrichment of the fluorine-containing block (i.e., PTFEA) of amphiphilic diblock copolymer on the surface of the thermosets, which was further evidenced by surface atomic force microscopy (AFM). The measurement of critical stress intensity factor (K_1C) showed that the fracture toughness of the materials was significantly enhanced by the inclusion of a small amount of PTFEA-b-PGMA diblock copolymer.     

Structure and properties of highly stereoregular isotactic poly(methyl methacrylate) and syndiotactic poly(methyl methacrylate) blends treated with supercritical CO2

The structure and properties of highly stereoregular isotactic poly(methyl methacrylate) (it-PMMA) and syndiotactic poly(methyl methacrylate) (st-PMMA) blends with crystalline stereocomplex formed by supercritical CO₂ treatment at temperatures ranging from 35 to 130 °C were investigated by means of differential scanning calorimetry (DSC), wide-angle X-ray diffraction (WAXD), and dynamic mechanical analysis (DMA) measurements. The melting temperature, T_m, and the heat of fusion, ΔH_m, had maximum values at about 200 °C and 25 J/g, respectively. The degree of crystallinity evaluated by WAXD ranged in value from 32 to 38%. The fringed-micellar stereocomplex crystallites were formed in case of treatment temperatures below 90 °C, and the orderliness perpendicular to the helix axis of the fringed-micellar crystallites was considered to be increased with increasing treatment temperature. In case of treatment temperature of 130 °C, the fringed-micellar crystallites and the lamellar crystallites with high orderliness parallel to the helix axis coupled with the perpendicular orderliness were formed, and the respective double endothermic peaks, T_m¹ and T_m³, were observed in DSC due to the melting of the two kinds of stereocomplex crystallites. The it-PMMA/st-PMMA blends containing the fringed-micellar crystallites maintained high values of storage modulus, E′, up to higher temperature compared with the amorphous blends. The E′ of the blend treated with CO₂ at 130 °C decreased twice at temperatures corresponding to T_m¹ and T_m³.     

Halofluorocarbon plasma treatments of polystyrene and poly(methyl methacrylate) surfaces

The effect of halofluorocarbon (CF₄, CF₃Cl, CF₃Br) discharges on polystyrene (PS) and poly(methyl methacrylate) (PMMA) has been studied. It has been shown that, depending on the halogen/halocarbon radical ratio, polymerization or etching can occur. The discharge chemistry has been altered by changing the excitation electrode material, and thus enhancing or depressing the amount of halocarbon radicals in the discharge. In CF₃Br and CF₃Cl plasmas, mass spectroscopy revealed the formation of molecular chlorine and bromine. Ion bombardment has been shown, in both PS and PMMA, to enhance etch rates and to depress the deposition of plasma polymer. While the etch rates of PMMA by CF₄, CF₃Cl and CF₃Br have the same kinetic dependence on bias voltage, the same is not true for PS. In this case the etch rates by CF₃Cl and CF₃Br discharges are preferentially enhanced, due to the different interaction with the species present in the discharge. As to derivatization, the introduction of halogens is more efficient in PS than in PMMA. Interestingly, the introduction of Cl and Br is enhanced much more than that of F, possibly due to the interaction of the PS aromatic ring with molecular chlorine and bromine present in the discharge.     

Preparation of poly(methyl methacrylate)/titanium oxide composite particles via in‐situ emulsion polymerization

Poly(methyl methacrylate) (PMMA)/Titanium oxide (TiO₂) composite particles were prepared via in‐situ emulsion polymerization of MMA in the presence of TiO₂ particles. Before polymerization, the TiO₂ particles was modified by the silane coupling agent, which is crucial to ensure that PMMA reacts with TiO₂ via covalent bond bindings. The structure of the obtained PMMA/TiO₂ composite particles was characterized using Fourier transform infrared spectra (FTIR) and thermogravimetric analysis (TGA). The results indicate that there are covalent bond bindings between PMMA macromolecules and TiO₂ particles. Based on these facts, several factors affecting the resulting PMMA/TiO₂ composite system, such as the type of coupling agents, the mass ratio of the MMA to the modified TiO₂, the emulsifier concentration, and the initiator concentration, etc., were examined by the measurement of conversion of monomers, the gel content of polymers, the percentage of grafting, and the grafting efficiency, using gravity method or TGA method. As a result, the optimized recipe was achieved, and the percentage of grafting and the grafting efficiency could reach 216.86 and 96.64%, respectively. In addition, the obtained PMMA/TiO₂ composite particles were found to a stable colloidal dispersion in good solvent for PMMA. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 4056–4063, 2006     

Comparison of the phase behaviour of the liquid-crystalline polymer/poly(methyl methacrylate) and poly(vinyl acetate)/poly(methyl methacrylate) blends

The phase behaviour of blends of a liquid-crystalline polymer (LCP) and poly(methyl methacrylate) (PMMA), as well as the phase state of blends of PMMA and poly(vinyl acetate) (PVA) has been investigated using light scattering and phase-contrast optical microscopy. The blends of LCP and PMMA have been obtained by coagulation from ternary solutions. The cloud point curves were determined. It was established that both pairs demix upon heating, ie have an LCST. In the region of intermediate composition, the phase separation proceeds according to a spinodal mechanism; however for LCP/PMMA blends, the decomposition proceeds according to a non-linear regime from the very onset. In the region of small amounts of LCP, the phase separation follows a mechanism of nucleation and growth. For PMMA/PVA blends, the spinodal decomposition proceeds according to a linear regime, in spite of the molecular mobility that PVA chains develop at lower temperatures. Only after prolonged heat treatment does the process transit to a non-linear regime. The data show a similarity between the phase behaviour of blends of liquid-crystalline and of flexible amorphous polymers. The distinction consists of the absence of a linear regime of decomposition for LCP-PMMA blends. © 1999 Society of Chemical Industry     

Synthesis and properties of poly(methyl methacrylate)/montmorillonite (PMMA/MMT) nanocomposites

PMMA/MMT nanocomposites were successfully synthesized via in situ intercalative polymerization, and characterized by means of wide‐angle X‐ray diffractometry, transmission electron microscopy, thermal gravimetric analysis, dynamic mechanical analysis and Fourier‐transform infrared analysis. The nanocomposites possess partially exfoliated and partially intercalated structure, in which the silicate layers are exfoliated into nanometre secondary particles with thickness of less than 20 nm and uniformly dispersed in the polymer matrix. In comparison with pure PMMA, the thermal stability, glass transition temperature, and mechanical properties of the polymer are notably improved by the presence of the nanometric silicate layers. It was found that part of the PMMA chains in the nanocomposites are well immobilized inside and/or onto the layered silicates and, therefore, the unique properties of the nanocomposites result from the strong interactions between the nanometric silicate layers and the polymer chains. Copyright © 2003 Society of Chemical Industry     

Preparation and characterization of graft copolymers of methyl methacrylate and poly(n-hexyl isocyanate) macromonomers

Living poly(n-hexyl isocyanate) (PHIC) was deactivated with methacryloyl chloride to produce methacryl-terminated poly(n-hexyl isocyanate) (PHIC-MA) rodlike macromonomers. Radical copolymerization of methyl methacrylate (MMA) with PHIC-MA was performed using 2,2′-azobis(isobutyronitrile) as an initiator in benzene at 60 °C to prepare poly(methyl methacrylate)-graft-poly(n-hexyl isocyanate) (PMMA-graft-PHIC) graft copolymers. The monomer reactivity ratios of MMA (M₁) and PHIC-MA (M₂) were evaluated as r₁=11.5 and r₂=∼0, exhibiting remarkably lower reactivity of PHIC-MA macromonomer than that of common macromonomers. The resultant graft copolymers were characterized using gel permeation chromatography equipped with low-angle laser light-scattering to determine the molecular weights, and equipped with a refractive index detector and an ultraviolet light detector to estimate a PHIC weight fraction of PMMA-graft-PHIC at the ith elution volume of the GPC chromatogram. There are 2-3 PHIC grafts per PMMA molecule, and the PHIC rodlike chains might be difficult to introduce into the PMMA main chains having higher molecular weights. A specific dimension of PMMA-graft-PHIC in solution was discussed in detail.     

Epoxy resin containing poly(ethylene oxide)-block-poly(?-caprolactone) diblock copolymer: Effect of curing agents on nanostructures

An amphiphilic diblock copolymer, poly(ethylene oxide)-block-poly(?-caprolactone) (PEO-b-PCL) was synthesized via the ring-opening polymerization of ?-caprolactone in the presence of a hydroxyl-terminated poly(ethylene oxide) monomethyl ether. The diblock copolymer was incorporated into epoxy thermosets. It is found that the formation of nanostructures of thermosetting blends is quite dependent on the uses of aromatic amine hardeners. For 4,4′-methylenebis(2-chloroaniline) (MOCA)-cured thermosetting system, the homogeneous morphology was obtained at the compositions investigated. Nonetheless, the nanostructured thermosets were obtained when the blends were cured with 4,4′-diaminodiphenylsulfone (DDS). The differential scanning calorimetry (DSC) showed that the nanostructured thermosets did not displayed any crystallinity although the subchains of the diblock copolymer are crystalline. The nanostructures were evidenced by means of atomic force microscopy (AFM), small-angle X-ray scattering (SAXS) and transmission electron microscopy (TEM). The dependence of morphological structures on the types of aromatic amines for epoxy and PEO-b-PCL thermosetting blends were interpreted on the basis of the difference in hydrogen bonding interactions resulting from the structure of curing agents. Considering the complete miscibility of the subchains (viz. PEO and PCL) with the precursors of epoxy resin before curing, it is judged that the formation of the nanostructures in the thermosets follows the mechanism of reaction-induced microphase separation, which is in marked contrast to the mechanism of self-assembly, i.e., micelle structures of block copolymers are formed prior to curing, followed by fixing these nanostructures via curing.     

Crystallization behavior and hydrophilicity of poly(vinylidene fluoride)/poly(methyl methacrylate)/poly(vinyl pyrrolidone) ternary blends

Ternary blends composed of matrix polymer poly(vinylidene fluoride) (PVDF) with different proportions of poly(methyl methacrylate) (PMMA)/poly(vinyl pyrrolidone) (PVP) blends were prepared by melt mixing. The miscibility, crystallization behavior, mechanical properties and hydrophilicity of the ternary blends have been investigated. The high compatibility of PVDF/PMMA/PVP ternary blends is induced by strong interactions between the carbonyl groups of the PMMA/PVP blend and the CF₂ or CH₂ group of PVDF. According to the Fourier transform infrared and wide‐angle X‐ray difffraction analyses, the introduction of PMMA does not change the crystalline state (i.e. α phase) of PVDF. By contrast, the addition of PVP in the blends favors the transformation of the crystalline state of PVDF from non‐polar α to polar β phase. Moreover, the crystallinity of the PVDF/PMMA/PVP ternary blends also decreases compared with neat PVDF. Through mechanical analysis, the elongation at break of the blends significantly increases to more than six times that of neat PVDF. This confirms that the addition of the PMMA/PVP blend enhances the toughness of PVDF. Besides, the hydrophilicity of PVDF is remarkably improved by blending with PMMA/PVP; in particular when the content of PVP reaches 30 wt%, the water contact angle displays its lowest value which decreased from 91.4° to 51.0°. Copyright © 2011 Society of Chemical Industry     

Electrospinning of cyclodextrin functionalized poly(methyl methacrylate) (PMMA) nanofibers

Cyclodextrin functionalized PMMA nanofibers (PMMA/CD) were successfully produced by electrospinning technique with the goal to develop functional nanowebs. Bead-free uniform electrospun PMMA/CD nanofibers were obtained from a homogeneous solution of CDs and PMMA in dimethylformamide (DMF) using three different types of CDs, α-CD, β-CD and γ-CD. The electrospinning conditions were optimized in order to form bead-free PMMA/CD nanofibers by varying the concentrations of PMMA and CDs in the solutions. The concentration of CDs was varied from 5% up to 50% w/w, with respect to the PMMA matrix. We find that the presence of the CDs in the PMMA solutions facilitates the electrospinning of bead-free nanofibers from the lower polymer concentrations and this behavior is attributed to the high conductivity and viscosity of the PMMA/CD solutions. The X-ray diffraction (XRD) spectra of PMMA/CD nanowebs did not show any significant diffraction peaks indicating that the CD molecules are homogeneously distributed within the PMMA matrix and does not form any phase separated crystalline aggregates. Furthermore, attenuated total reflection Fourier transform infrared (ATR-FTIR) studies elucidate that some CD molecules are located on the surface of the nanowebs. This suggests that these CD functionalized nanowebs may have the potential to be used as molecular filters and/or nanofilters for waste treatment purposes.     

Solvent effects on the miscibility of poly(methyl methacrylate)/poly(bisphenol a carbonate) blends

Blends of atactic or syndiotactic poly(methyl methacrylate) (designated as aPMMA or sPMMA) and poly(bisphenol A carbonate) (PC) were prepared from solution casting. Tetrahydrofuran (THF) and chloroform were used as solvent. Experimental results indicated that the as‐cast blends from THF were quite different from the chloroform‐cast ones. After film preparation, THF‐cast blends did not show any visible phase separation. However, chloroform‐cast blends formed a phase‐separated structure. The as‐cast PC from either solvent was not completely amorphous, and had a melting point at 239–242°C, indicating a certain degree of crystallinity. In contrast, the quenched samples of aPMMA/PC blends prepared from the two solvents behaved virtually the same. They both showed aPMMA dissolves better in PC, but PC solubility in aPMMA is very little. Using sPMMA instead of aPMMA to blend with PC, different results were obtained. The quenched sPMMA/PC blends cast from THF showed only one T_g. However, immiscibility (i.e., two T_gs) was found in the same blend system when cast from chloroform. THF was believed to cause the observation of single T_g due to the following kinetic reason. sPMMA and PC were still trapped together even after THF removal in a homogeneous, but nonequilibrium state below the glass transition. Therefore, the quenched sPMMA/PC blends were not truly thermodynamically miscible. From the results of aPMMA or sPMMA with PC, increasing syndiotacticity seemed to improve the miscibility between PMMA and PC. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 2842–2850, 2001     

Properties of mineral filled poly(lactic acid)/poly(methyl methacrylate) blend

This study examines the influence of three different minerals, that is, clay, calcium carbonate, and quartz on the physical, thermal, and mechanical properties of poly(lactic acid) (PLA)/poly(methyl methacrylate) blend. Rheological behavior and phase structure were initially studied by small-amplitude oscillatory shear rheology. Clay- and quartz-filled materials presented an increase in viscosity at low frequency associated with the presence of a yield stress. However, this behavior was not observed for calcium carbonate filled materials due to a matrix degradation effect. To elucidate this aspect, thermal stability and thermal properties were examined by thermogravimetric analysis and differential scanning calorimetry, showing that calcium carbonate promotes degradation of the PLA phase. No nucleating effect was observed in the presence of the minerals. Dynamical mechanical analysis and mechanical characterization revealed an increase of the overall softening temperature and, a reinforcing effect for clay- and quartz-based composites. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 46927.     

Morphological and infra-red studies on highly oriented poly(vinylidene fluoride)/poly(methyl methacrylate) blends

Highly oriented melt drawn films of poly(vinylidene fluoride) (PVDF) and blends of poly(vinylidene fluoride) and poly(methyl methacrylate) (PMMA) have been studied by transmission electron microscopy, electron diffraction and infra-red spectroscopy. Infra-red spectra show the second moment of the orientation function for PVDF samples to be greater than 0.94. Using such a sample, the transition dipole directions relative to the chain axis have been calculated. Electron microscopic studies of the PVDF/PMMA blends show a transformation for pure PVDF from a lamellar morphology to a mixture of lamellar and needle-like crystals for the 80/20 blend. The 60/40 blend shows a pure needle-like morphology. The β phase content for this blend is dependent upon the composition and thermal history. An increase in the β phase content is observed with the addition of PMMA. After annealing at 110°C, the 50/50 blend shows a lamellar β phase morphology. A significant increase in the segmental orientation of PVDF is also observed.     

Morphological characterization of attapulgite/poly(methyl methacrylate) particles prepared by soapless emulsion polymerization

BACKGROUND: The synthesis of core–shell inorganic/polymer nanocomposites, in which the polymer shell determines the chemical properties and the interaction with the environment, whereas their physical properties are governed by both the size and shape of the inorganic core and the surrounding organic layer, is an area of increasing research activity. RESULTS: Core–shell and bead–string shaped attapulgite/poly(methyl methacrylate) (ATP/PMMA) nanocomposite particles were prepared by soapless emulsion polymerization in an aqueous suspension of attapulgite organically modified with cetyltrimethylammonium bromide. CONCLUSION: Transmission electron microscopy analysis results showed that the amounts of the monomer added had no influence on the morphologies of the ATP/PMMA particles. The morphologies only depended on the length/diameter ratio of the attapulgite fibrillar single crystal used. Long ATP needles formed the bead–string structure while short ATP needles formed the core–shell structure. Copyright © 2007 Society of Chemical Industry     

Rheological properties of poly(methyl methacrylate)/rigid ladderlike polyphenylsilsesquioxane blends

A series of poly(methyl methacrylate) (PMMA) blends with rigid ladderlike polyphenylsilsesquioxane (PPSQ) were prepared at weight ratios of 100/0, 95/5, 90/10, 85/15, and 80/20 by solution casting and then hot‐pressing. Their rheological properties have been studied under both dynamic shear and uniaxial elongation conditions. Their rheological properties depend on the compositions. The storage modulus, G′, loss modulus, G″, and dynamic shear viscosity, η*, of the PMMA/PPSQ 95/5 blend were slightly lower than those of pure PMMA. However, the values of G′, G″, and η* for the other PMMA/PPSQ blends are higher than those of PMMA. The G′ values increase with an increase in PPSQ content from 5% through 15% PPSQ at low frequencies and then drop as the PPSQ content increases to 20%. Uniaxial elongational viscosity (η_E) data demonstrate that PMMA/PPSQ blends exhibit slightly weaker (5% PPSQ) and much weaker (10% PPSQ) strain‐hardening than PMMA. In contrast, the PMMA/PPSQ 85/15 blend shows strain‐softening. Neither strain‐hardening nor strain‐softening was observed in the 80/20 blend. The special rheological properties for the 95/5 blend is probably due to a decrease in PMMA entanglements brought by the specific PMMA–PPSQ interactions. Rheological properties of PMMA/PPSQ blends with higher PPSQ content (≥10%) are mainly affected by formation of hard PPSQ particles. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 352–359, 2007     

Preparation of gold nanoparticles on poly(methyl methacrylate) nanospheres with surface-grafted poly(allylamine)

A facile method for in situ anchoring of gold nanoparticles onto the surface of polymer nanospheres was successfully developed in this study. As polymer nanospheres, amphiphilic poly(methyl methacrylate) (PMMA)/poly(allylamine) (PAA) nanospheres were prepared by graft copolymerization of methyl methacrylate from PAA. The gold nanoparticles anchored were spherically symmetric and the average sizes were ∼12 nm for all samples. It was found that surface-grafted PAA effectively anchored and stabilized gold nanoparticles for a long period of time.